vnp ultrasonic sensors Extract from our online store: Current to:

Transcription

1 Extract from our online store: vnp ultrasonic sensors Current to: microsonic gmbh, hauert 16, d dortmund, telephone: , fax: ,

2 The vnp sensors supplement the successful mic+ sensor series. The technical data correspond to those of the mic+ sensors. Highlights External teaching ::: for remote sensor setting via the machine control or by the operator Externally continuously displaceable analogue characteristic ::: for fine application adjustments Numerically settable relative detect points ::: for precise switched output pre-setting Numerically settable relative analogue characteristic ::: for precise analogue output pre-setting Direct measurement value output in mm/cm or % via digital display ::: for immediately visible results Distance value display relative to the virtual zero ::: for relative distance measurement High-resolution display of distance values on the digital display ::: for accuracy down to the decimillimetre Automatic synchronisation ::: for the simultaneous operation of up to ten sensors in confined space Temperature compensation ::: for accurate measurements in case of temperature fluctuations Automatic switchover between current and voltage output ::: for ease of handling Operating voltage 9 30 V ::: for application in various supply networks

3 Description With the vnp sensors, relative detect distances (or relative window boundaries for the analogue output) are set via TouchControl as opposed to the mic+ sensors. Via pin 5 at the sensor plug (Com input), the current distance to the object can then be taught in at any time. For this purpose, pin 5 must be applied to +UB for 3 seconds. The respectively taught-in distance to the object is referred to as the virtual zero. The absolute detect distances (or absolute window boundaries for the analogue output) are derived from the summation of the previously programmed relative detect distances (or relative window boundaries) and the taught-in virtual zero. If, for example, a relative detect distance of -50 mm was programmed for switched output D1 and a relative detect distance of +80 mm was programmed for switched output D2 via TouchControl and the absolute distance to the object is then taught in via pin 5 as the virtual zero with 600 mm, the detect points are as follows: D1: -50 mm mm = 550 mm D2: +80 mm mm = 680 mm The vnp sensors are particularly useful whenever a detect distance has to be set recurrently by the machine control or manually by the operator, e.g. upon every machine cycle or machine setup. The characteristic curve of the analogue signal can also optionally be continuously displaced for sensors with analogue output via pin 5 (Com input). This special function has to be initially activated via TouchControl. If +UB is then applied to pin 5 at the sensor plug for <3 seconds, the virtual zero is continuously displaced away from the sensor; if, in contrast, +UB is applied for >3 seconds, the virtual zero is continuously displaced towards the sensor. A renewed short application of +UB to pin 5 stops the process. With vnp sensors with analogue output, the characteristic curve can be programmed numerically as the relative window width with this method, for example from -50 mm to +80 mm a rising analogue characteristic 0 10 V. Via pin 5 at the sensor plug, the complete analogue characteristic curve can then be continuously displaced with the virtual zero. If several vnp sensors are operated in a confined space, they can be synchronised with each other via pin 5 at the sensor plug.

4 vnp-25/dd/tc detection zone 2 x pnp 350 mm design operating mode ultrasonic -specific means of measurement transducer frequency blind zone maximum range angle of beam spread resolution/sampling rate mm cylindrical M30 proximity switch/reflective mode window mode echo propagation time measurement 320 khz 30 mm 250 mm 350 mm please see graphics detection zone mm reproducibility ± 0.15 % accuracy electrical data operating voltage U B voltage ripple ± 10 % no-load current consumption type of connection 2 % (temperature drift internally compensated) 9-30 V d.c., reverse polarity protection 80 ma 5-pin M12 initiator plug

5 vnp-25/dd/tc outputs output 1 output 2 switching hysteresis switching frequency response time delay prior to availability inputs input 1 material ultrasonic transducer switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof 3 mm 25 Hz 32 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 110 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display

6 vnp-25/iu/tc detection zone 1 x analogue 4-20 ma V 350 mm mm design cylindrical M30 operating mode analogue distance measurements ultrasonic -specific means of measurement echo propagation time measurement transducer frequency 320 khz blind zone 30 mm 250 mm maximum range 350 mm angle of beam spread please see graphics detection zone resolution/sampling rate mm reproducibility ± 0.15 % accuracy 2 % (temperature drift internally compensated) electrical data operating voltage U B 9-30 V d.c., reverse polarity protection voltage ripple ± 10 % no-load current consumption 80 ma type of connection 5-pin M12 initiator plug

7 vnp-25/iu/tc outputs output 1 response time delay prior to availability inputs input 1 material ultrasonic transducer analogue output current: 4-20 ma / voltage: 0-10 V (at U B 15 V), short-circuit-proof switchable rising/falling 32 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 110 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display

8 vnp-35/dd/tc detection zone 2 x pnp 600 mm design operating mode ultrasonic -specific means of measurement transducer frequency blind zone maximum range angle of beam spread resolution/sampling rate mm cylindrical M30 proximity switch/reflective mode window mode echo propagation time measurement 400 khz 65 mm 350 mm 600 mm please see graphics detection zone mm reproducibility ± 0.15 % accuracy electrical data operating voltage U B voltage ripple ± 10 % no-load current consumption type of connection 2 % (temperature drift internally compensated) 9-30 V d.c., reverse polarity protection 80 ma 5-pin M12 initiator plug

9 vnp-35/dd/tc outputs output 1 output 2 switching hysteresis switching frequency response time delay prior to availability inputs input 1 material ultrasonic transducer switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof 5 mm 8 Hz 70 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 110 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display

10 vnp-35/iu/tc detection zone 1 x analogue 4-20 ma V 600 mm mm design cylindrical M30 operating mode analogue distance measurements ultrasonic -specific means of measurement echo propagation time measurement transducer frequency 400 khz blind zone 65 mm 350 mm maximum range 600 mm angle of beam spread please see graphics detection zone resolution/sampling rate mm reproducibility ± 0.15 % accuracy 2 % (temperature drift internally compensated) electrical data operating voltage U B 9-30 V d.c., reverse polarity protection voltage ripple ± 10 % no-load current consumption 80 ma type of connection 5-pin M12 initiator plug

11 vnp-35/iu/tc outputs output 1 response time delay prior to availability inputs input 1 material ultrasonic transducer analogue output current: 4-20 ma / voltage: 0-10 V (at U B 15 V), short-circuit-proof switchable rising/falling 70 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 110 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display

12 vnp-130/dd/tc detection zone 2 x pnp 2,000 mm design operating mode ultrasonic -specific means of measurement transducer frequency blind zone maximum range angle of beam spread resolution/sampling rate 200-1,300 mm cylindrical M30 proximity switch/reflective mode window mode echo propagation time measurement 200 khz 200 mm 1,300 mm 2,000 mm please see graphics detection zone 0.18 mm reproducibility ± 0.15 % accuracy electrical data operating voltage U B voltage ripple ± 10 % no-load current consumption type of connection 2 % (temperature drift internally compensated) 9-30 V d.c., reverse polarity protection 80 ma 5-pin M12 initiator plug

13 vnp-130/dd/tc outputs output 1 output 2 switching hysteresis switching frequency response time delay prior to availability inputs input 1 material ultrasonic transducer switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof 20 mm 6 Hz 110 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 150 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display

14 vnp-130/iu/tc detection zone 1 x analogue 4-20 ma V 2,000 mm 200-1,300 mm design cylindrical M30 operating mode analogue distance measurements ultrasonic -specific means of measurement echo propagation time measurement transducer frequency 200 khz blind zone 200 mm 1,300 mm maximum range 2,000 mm angle of beam spread please see graphics detection zone resolution/sampling rate 0.18 mm reproducibility ± 0.15 % accuracy 2 % (temperature drift internally compensated) electrical data operating voltage U B 9-30 V d.c., reverse polarity protection voltage ripple ± 10 % no-load current consumption 80 ma type of connection 5-pin M12 initiator plug

15 vnp-130/iu/tc outputs output 1 response time delay prior to availability inputs input 1 material ultrasonic transducer analogue output current: 4-20 ma / voltage: 0-10 V (at U B 15 V), short-circuit-proof switchable rising/falling 110 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 110 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display

16 vnp-340/dd/tc detection zone 2 x pnp 5,000 mm design operating mode ultrasonic -specific means of measurement transducer frequency blind zone maximum range angle of beam spread resolution/sampling rate 350-3,400 mm cylindrical M30 proximity switch/reflective mode window mode echo propagation time measurement 120 khz 350 mm 3,400 mm 5,000 mm please see graphics detection zone 0.18 mm reproducibility ± 0.15 % accuracy electrical data operating voltage U B voltage ripple ± 10 % no-load current consumption type of connection 2 % (temperature drift internally compensated) 9-30 V d.c., reverse polarity protection 80 ma 5-pin M12 initiator plug

17 vnp-340/dd/tc outputs output 1 output 2 switching hysteresis switching frequency response time delay prior to availability inputs input 1 material ultrasonic transducer switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof 50 mm 3 Hz 180 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 250 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display

18 vnp-340/iu/tc detection zone 1 x analogue 4-20 ma V 5,000 mm 350-3,400 mm design cylindrical M30 operating mode analogue distance measurements ultrasonic -specific means of measurement echo propagation time measurement transducer frequency 120 khz blind zone 350 mm 3,400 mm maximum range 5,000 mm angle of beam spread please see graphics detection zone resolution/sampling rate 0.18 mm reproducibility ± 0.15 % accuracy 2 % (temperature drift internally compensated) electrical data operating voltage U B 9-30 V d.c., reverse polarity protection voltage ripple ± 10 % no-load current consumption 80 ma type of connection 5-pin M12 initiator plug

19 vnp-340/iu/tc outputs output 1 response time delay prior to availability inputs input 1 material ultrasonic transducer analogue output current: 4-20 ma / voltage: 0-10 V (at U B 15 V), short-circuit-proof switchable rising/falling 180 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 250 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display

20 vnp-600/dd/tc detection zone 2 x pnp 8,000 mm design operating mode ultrasonic -specific means of measurement transducer frequency blind zone maximum range angle of beam spread resolution/sampling rate 600-6,000 mm cylindrical M30 proximity switch/reflective mode window mode echo propagation time measurement 80 khz 600 mm 6,000 mm 8,000 mm please see graphics detection zone 0.18 mm reproducibility ± 0.15 % accuracy electrical data operating voltage U B voltage ripple ± 10 % no-load current consumption type of connection 2 % (temperature drift internally compensated) 9-30 V d.c., reverse polarity protection 80 ma 5-pin M12 initiator plug

21 vnp-600/dd/tc outputs output 1 output 2 switching hysteresis switching frequency response time delay prior to availability inputs input 1 material ultrasonic transducer switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof switching output pnp: I max = 200 ma (U B -2V) NOC/NCC adjustable, short-circuit-proof 100 mm 2 Hz 240 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 220 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display

22 vnp-600/iu/tc detection zone 1 x analogue 4-20 ma V 8,000 mm 600-6,000 mm design cylindrical M30 operating mode analogue distance measurements ultrasonic -specific means of measurement echo propagation time measurement transducer frequency 80 khz blind zone 600 mm 6,000 mm maximum range 8,000 mm angle of beam spread please see graphics detection zone resolution/sampling rate 0.18 mm reproducibility ± 0.15 % accuracy 2 % (temperature drift internally compensated) electrical data operating voltage U B 9-30 V d.c., reverse polarity protection voltage ripple ± 10 % no-load current consumption 80 ma type of connection 5-pin M12 initiator plug

23 vnp-600/iu/tc outputs output 1 response time delay prior to availability inputs input 1 material ultrasonic transducer analogue output current: 4-20 ma / voltage: 0-10 V (at U B 15 V), short-circuit-proof switchable rising/falling 240 ms < 300 ms class of protection to EN IP 67 operating temperature storage temperature weight technical features/characteristics temperature compensation controls scope for settings synchronization multiplex indicators particularities documentation (download) pin assignment synchronisation input teach-in input brass sleeve, nickel-plated, plastic parts, PBT, TPU polyurethane foam, epoxy resin with glass contents -25 C to +70 C -40 C to +85 C 220 g 2 pushbuttons + LED display (TouchControl) Teach-in TouchControl LCA-2 with LinkCopy or LinkControl software 3-digit LED display, 2 x three-colour LED virtual zero settable display