mobile data carrier TW-R16-B128 Phone: Fax: Web: -

Transcription

1 Mobile data carrier TW-R6-B28 mobile data carrier read/write compatible with a series of BL ident read-write heads (see data sheet or compatibility table) EEPROM, memory size 28 bytes Type TW-R6-B28 Ident-No Data transfer inductance coupling Working frequency 3.56 MHz Memory read/write Memory type EEPROM Memory size 28 Byte Freely usable memory 2 Byte Number of read operations unlimited Number of write operations 0 5 Typical read time 2 ms/byte Typical write time 3 ms/byte Radio communication and protocol standards ISO 5693 Minimum distance to metal Ambient temperature Storage temperature Housing Housing material Material active face Protection class Packaged quantity 0 mm C C 60 C, x35 h 220 C, x30 s R6 Plastic, PA6 Plastic IP69K Functional principle The HF read-write heads and the work frequency of 3.56 MHz form a transmission zone, the size of which (0 500 mm) varies depending on the combination of readwrite head and data carrier. The read-write distances mentioned here, only represent standard values measured under laboratory conditions. The read-write distances of the data carriers for mounting in metal TW-R**-M(MF) were determined in metal. Due to component tolerances, mounting conditions, ambient conditions and material influences (especially metal, ) attainable distances can deviate by 30 %. Therefore testing of the application under real operating conditions is indspensable (especially regarding read-write on the fly)!

2 Mobile data carrier TW-R6-B28 Read/write heads Dimensions Type designation Read-write distance Transfer zone Minimum distance between two readwrite heads Ident - no. Recommended [mm] length [mm] width offset [mm] TB-M8-H TB-EM8WD-H TB-M8-H47/S TB-EM8WD-H47/S TN-M8-H TN-EM8WD-H TN-M8-H47/S TN-EM8WD-H47/S TB-M30-H TB-EM30WD-H TB-M30-H47/S TB-EM30WD-H47/S TN-M30-H TN-EM30WD-H TN-M30-H47/S TN-EM30WD-H47/S [mm]

3 Mobile data carrier TW-R6-B28 Read/write heads Dimensions Type designation Read-write distance Transfer zone Minimum distance between two readwrite heads Ident - no. Recommended [mm] length [mm] width offset [mm] [mm] TN-CK40-H TN-CK40-H47/S HT-IDENT-H HT-IDENT-H TN-Q4-0.5-RS4.47T

4 Mobile data carrier TW-R6-B28 Read/write heads Dimensions Type designation Read-write distance Transfer zone Minimum distance between two readwrite heads Ident - no. Recommended [mm] length [mm] width offset [mm] [mm] TN-Q80-H TN-Q80-H47/S TNLR-Q80-H TNLR-Q80-H47/S TNLR-Q80L400-H Lengthwise TNLR-Q80L400-H TNLR-Q80L400-H47L TNLR-Q80L400-H47L Lengthwise TNLR-Q350-H TNLR-Q350-H TNLR-Q350-H47/S

5 Mobile data carrier TW-R6-B28 Read/write heads Dimensions Type designation Ident - no. TN-S32XL-H Read-write distance Transfer zone Minimum distance between two readwrite heads Recommended [mm] length [mm] width offset [mm] [mm]

6 Mobile data carrier TW-R6-B28 Compatible handhelds PD-IDENT Handheld for mobile reading and writing on data carriers. PDA-IDENT The handheld can be used with two different antennas. Internal antenna, PDA-IDENT-IA, External antenna, PDA-IDENT-EA,

7 TURCK RFID Products RFID System - Read/Write Head Rectangular, 40 mm High 5-positions Turnable Plastic, PBT-GF30-V0 Partial Embedding Power Supply (24 VDC) and Function via BL ident Interfaces Connector (M2) eurofast, Connection via BL ident Connecting Cable Housing Part Number Function Principle TN-Q80-H47 The BL ident read/write head (transceiver) is used to exchange data with the data carrier (TAG). Together they form an air interface whose size depends on the combination of transceiver and TAG. The data carriers are passive. When they enter the air interface of the transceiver, the power from the transceiver is transferred inductively and data transfer completed. BL ident TAGs on the following page can be combined with this BL ident transceiver. The read/write interval varies between in. (3-7 mm). TAGs available with EEPROM or FRAM memory. Part Number ID Number Mounting Mode Ambient temperature Data Transfer Output function Operating frequency TN-Q80-H47 M Non flush, flush mounting possible -25 to +70 C (-3 to +58 F) Inductive 4-wire, write/read 3.56 MHz Housing Rectangular, CK40 Housing material Plastic, PBT-GF30-V0, yellow Material active face Plastic, PBT-GF30-V0, yellow Connection Connector, M2x Vibration resistance 55 Hz ( mm) Shock resistance 30 g ( ms) Protection IP 67 Pinout Power On Indication Read/write head off TAG with air interface Wiring Maximum cable length LED solid LED.5 Hz LED 3 Hz 50 m Mating Cordset: RK 4.5T-*-RS 4.5T/S250

8 Industrial Automation Associated Data Carrier Housing Fig. Part Number ID Number Read/Write Range Zone Width Distance Length minimum between two read/write heads Recomm. TW-R6-B28 M (3).52 (3) (63).968 (50) (63) 9.92 (252) 2 2 TW-R20-B28 M (33).709 (8) (67) (57) (288) 3 3 TW-R30-B28 M (40).866 (22) 3.50 (80) (64) 3.89 (8) (324) 4 TW-R50-B28 M (58).220 (3) (7) 3.66 (93) (7) (468) 4 2 TW-R20-K2 M (30).630 (6) (60) (5) (64) (256) 3 TW-R30-K2 M (20) (58) (288) 5 4 TW-R50-K2 M (52).063 (27) 4.34 (05) (83) 4.34 (05) (420) 5 TW-R50-90-HT-B28 M (58).220 (3) (7) 3.66 (93) (7) (468) 5 TW-R50-90-HT-K2 M (52).063 (27) 4.34 (05) (83) 4.34 (05) (420) Smaller intervals are possible by alternating switching the read/write heads on and off with software. 0 mm air gap required when mounting to ferrous metal. See accessories on page 26 for spacers. Ambient temperature: -25 to +85 C (-3 to +85 F); (-40 to +20 C (-40 to +40 F) for TW-R*-HT...).

9 TURCK RFID Products RFID System - Read/Write Head Rectangular, 40 mm High 5-positions Turnable Plastic, PBT-GF30-V0 Partial Embedding Power Supply (24 VDC) and Function via BL ident Interfaces Connector (M2) eurofast, Connection via BL ident Connecting Cable Housing Part Number Function Principle TN-CK40-H47 The BL ident read/write head (transceiver) is used to exchange data with the data carrier (TAG). Together they form an air interface whose size depends on the combination of transceiver and TAG. The data carriers are passive. When they enter the air interface of the transceiver, the power from the transceiver is transferred inductively and data transfer completed. BL ident TAGs on the following page can be combined with this BL ident transceiver. The read/write interval varies between in. (-8 mm). TAGs available with EEPROM or FRAM memory. Part Number ID Number Mounting Mode Ambient temperature Data Transfer Output function Operating frequency TN-CK40-H47 M Non flush, flush mounting possible -25 to +70 C (-3 to +58 F) Inductive 4-wire, write/read 3.56 MHz Housing Rectangular, CK40 Housing material Plastic, PBT-GF30-V0, black Material active face Plastic, PBT-GF30-V0, yellow Connection Connector, M2x Vibration resistance 55 Hz ( mm) Shock resistance 30 g ( ms) Protection IP 67 Power On Indication Read/write head off TAG with air interface LED solid LED.5 Hz LED 3 Hz Pinout Wiring Maximum cable length Accessories 50 m Fixing clamp BS4-CK40 (included in delivery) Mating Cordset: RK 4.5T-*-RS 4.5T/S250

10 Industrial Automation Associated Data Carrier Housing Fig. Part Number ID Number Read/Write Range Zone Width Distance Length minimum between two read/write heads Recomm. TW-R6-B28 M (22).433 ().772 (45).260 (32).575 (40) (60) 2 2 TW-R20-B28 M (24).472 (2).929 (49).457 (37).850 (47) (88) 3 3 TW-R30-B28 M (27).52 (3) 2.26 (54).693 (43) 2.26 (54) (26) 4 TW-R50-B28 M (40).866 (22) 3.89 (8) (64) 3.89 (8) (324) 4 2 TW-R20-K2 M (22).394 (0).732 (44).299 (33).654 (42) 6.64 (68) 3 TW-R30-K2 M (24).433 ().890 (48).496 (38).890 (48) (92) 5 4 TW-R50-K2 M (9) (57) (288) 5 TW-R50-90-HT-B28 M (40).866 (22) 3.89 (8) (64) 3.89 (8) (324) 5 TW-R50-90-HT-K2 M (9) (57) (288) Smaller intervals are possible by alternating switching the read/write heads on and off with software. 0 mm air gap required when mounting to ferrous metal. See accessories on page 26 for spacers. Ambient temperature: -25 to +85 C (-3 to +85 F); (-40 to +20 C (-40 to +40 F) for TW-R*-HT...).

11 TURCK RFID Products RFID System - Read/Write Head Threaded Barrel, M30x.5, Chrome Plated Brass Flush Mounting Power Supply (24 VDC) and Function via BL ident Interfaces Connector (M2) eurofast, Connection via BL ident Connecting Cable Housing Part Number Function Principle TN-M30-H47 The BL ident read/write head (transceiver) is used to exchange data with the data carrier (TAG). Together they form an air interface whose size depends on the combination of transceiver and TAG. The data carriers are passive. When they enter the air interface of the transceiver, the power from the transceiver is transferred inductively and data transfer completed. BL ident TAGs on the following page can be combined with this BL ident transceiver. The read/write interval varies between in. (9-54 mm). TAGs available with EEPROM or FRAM memory. Part Number ID Number Mounting Mode Ambient temperature Data Transfer Output function Operating frequency TN-M30-H47 M Flush -25 to +70 C (-3 to +58 F) Inductive 4-wire, write/read 3.56 MHz Housing Threaded barrel, M30x Housing material Metal, CuZn, chrome plated Material active face Plastic, PA2-GF30 Connection Connector, M2x Vibration resistance 55 Hz ( mm) Shock resistance 30 g ( ms) Protection IP 67 Power On Indication Read/write head off TAG with air interface Wiring Maximum cable length LED solid LED.5 Hz LED 3 Hz 50 m Pinout Mating Cordset: RK 4.5T-*-RS 4.5T/S250

12 Industrial Automation Associated Data Carrier Housing Fig. Part Number ID Number Read/Write Range Zone Width Distance Length minimum between two read/write heads Recomm. TW-R6-B28 M (6).354 (9).260 (32).02 (28) (44) 2 2 TW-R20-B28 M (6).394 (0).299 (33).02 (28).299 (33) 5.97 (32) 3 3 TW-R30-B28 M (20).433 ().575 (40).260 (32).64 (4) (64) 4 TW-R50-B28 M (27).52 (3) 2.26 (54).968 (50) (63) 9.92 (252) 4 2 TW-R20-K2 M (4).35 (8).42 (29).024 (26).42 (29) (6) 3 TW-R30-K2 M (8).394 (0) (28) (44) 5 4 TW-R50-K2 M (24).472 (2).890 (48).772 (45) (56) 8.89 (224) 5 TW-R50-90-HT-B28 M (27).52 (3) 2.26 (54).968 (50) (63) 9.92 (252) 5 TW-R50-90-HT-K2 M (24).472 (2).890 (48).772 (45) (56) 8.89 (224) Smaller intervals are possible by alternating switching the read/write heads on and off with software. 0 mm air gap required when mounting to ferrous metal. See accessories on page 26 for spacers. Ambient temperature: -25 to +85 C (-3 to +85 F); (-40 to +20 C (-40 to +40 F) for TW-R*-HT...).

13 TURCK RFID Products RFID System - Read/Write Head Threaded Barrel, M30x.5, Chrome Plated Brass Flush Mounting Power Supply (24 VDC) and Function via BL ident Interfaces Connector (M2) eurofast, Connection via BL ident Connecting Cable Housing Part Number Function Principle TB-M30-H47 The BL ident read/write head (transceiver) is used to exchange data with the data carrier (TAG). Together they form an air interface whose size depends on the combination of transceiver and TAG. The data carriers are passive. When they enter the air interface of the transceiver, the power from the transceiver is transferred inductively and data transfer completed. BL ident TAGs on the following page can be combined with this BL ident transceiver. The read/write interval varies between in. (9-36 mm). TAGs available with EEPROM or FRAM memory. Part Number ID Number Mounting Mode Ambient temperature Data Transfer Output function Operating frequency TB-M30-H47 M Flush -25 to +70 C (-3 to +58 F) Inductive 4-wire, write/read 3.56 MHz Housing Threaded barrel, M30 x.5 Housing material Metal, CuZn, chrome plated Material active face Plastic, PA2-GF30 Connection Connector, M2x Vibration resistance 55 Hz ( mm) Shock resistance 30 g ( ms) Protection IP 67 Power On Indication Read/write head off TAG with air interface Wiring Maximum cable length LED solid LED.5 Hz LED 3 Hz 50 m Pinout Mating Cordset: RK 4.5T-*-RS 4.5T/S250

14 Industrial Automation Associated Data Carrier Housing Fig. Part Number ID Number Read/Write Range Zone Width Distance Length minimum between two read/write heads Recomm. TW-R6-B28 M ().354 (9).866 (22).669 (7).866 (22) (88) 2 2 TW-R20-B28 M (2).394 (0).945 (24).748 (9).945 (24) (96) 3 3 TW-R30-B28 M (4).433 ().02 (28).827 (2).02 (28) (2) 4 TW-R50-B28 M (8).52 (3) (3).535 (39) 6.42 (56) 4 2 TW-R20-K2 M (0).236 (6).827 (2).630 (6).827 (2) (84) 3 TW-R30-K2 M (2).354 (9).984 (25).748 (9).984 (25) (00) 5 4 TW-R50-K2 M (6).472 (2).260 (32).945 (24).378 (35) 5.52 (40) 5 TW-R50-90-HT-B28 M (8).52 (3) (3).535 (39) 6.42 (56) 5 TW-R50-90-HT-K2 M (6).472 (2).260 (32).945 (24).378 (35) 5.52 (40) Smaller intervals are possible by alternating switching the read/write heads on and off with software. 0 mm air gap required when mounting to ferrous metal. See accessories on page 26 for spacers. Ambient temperature: -25 to +85 C (-3 to +85 F); (-40 to +20 C (-40 to +40 F) for TW-R*-HT...).

15 TURCK RFID Products RFID System - Read/Write Head Threaded Barrel, M8x, Chrome Plated Brass Flush Mounting Power Supply (24 VDC) and Function via BL ident Interfaces Connector (M2) eurofast, Connection via BL ident Connecting Cable Housing Part Number Function Principle TN-M8-H47 The BL ident read/write head (transceiver) is used to exchange data with the data carrier (TAG). Together they form an air interface whose size depends on the combination of transceiver and TAG. The data carriers are passive. When they enter the air interface of the transceiver, the power from the transceiver is transferred inductively and data transfer completed. BL ident TAGs on the following page can be combined with this BL ident transceiver. The read/write interval varies between in. (4-36 mm). TAGs available with EEPROM or FRAM memory. Part Number ID Number Mounting Mode Ambient temperature Data Transfer Output function Operating frequency TN-M8-H47 M Non flush -25 to +70 C (-3 to +58 F) Inductive 4-wire, write/read 3.56 MHz Housing Threaded barrel, M8 x Housing material Metal, CuZn, chrome plated Material active face Plastic, PA2-GF30 Connection Connector, M2x Vibration resistance 55 Hz ( mm) Shock resistance 30 g ( ms) Protection IP 67 Power On Indication Read/write head off TAG with air interface Wiring Maximum cable length LED solid LED.5 Hz LED 3 Hz 50 m Pinout Mating Cordset: RK 4.5T-*-RS 4.5T/S250

16 Industrial Automation Associated Data Carrier Housing Fig. Part Number ID Number Read/Write Range Zone Width Distance Length minimum between two read/write heads Recomm. TW-R6-B28 M (2).57 (4).984 (25).827 (2).063 (27) (08) 2 2 TW-R20-B28 M (3).97 (5).024 (26).906 (23).42 (29) (6) 3 3 TW-R30-B28 M (3).236 (6).063 (27).945 (24).220 (3) (24) 4 TW-R50-B28 M (8).354 (9) (39).929 (49) 7.77 (96) 4 2 TW-R20-K2 M ().57 (4).906 (23).55 (4).024 (26) (04) 3 TW-R30-K2 M (2).236 (6).945 (24).827 (2).063 (27) (08) 4 TW-R50-K2 M (6).35 (8).260 (32).827 (2).732 (44) (76) Smaller intervals are possible by alternating switching the read/write heads on and off with software. 0 mm air gap required when mounting to ferrous metal. See accessories on page 26 for spacers. Ambient temperature: -25 to +85 C (-3 to +85 F).

17 TURCK RFID Products RFID System - Read/Write Head Threaded barrel, M8x, Chrome Plated brass Flush Mounting Power Supply (24 VDC) and Function via BL ident Interfaces Connector (M2) eurofast, Connection via BL ident Connecting Cable Housing Part Number Function Principle TB-M8-H47 The BL ident read/write head (transceiver) is used to exchange data with the data carrier (TAG). Together they form an air interface whose size depends on the combination of transceiver and TAG. The data carriers are passive. When they enter the air interface of the transceiver, the power from the transceiver is transferred inductively and data transfer completed. BL ident TAGs on the following page can be combined with this BL ident transceiver. The read/write interval varies between in. (4- mm). TAGs available with EEpROM or FRAM memory. Part Number ID Number Mounting Mode Ambient temperature Data Transfer Output function Operating frequency TB-M8-H47 M Flush -25 to +20 C (-3 to +40 F) Inductive 4-wire, write/read 3.56 MHz Housing Threaded barrel, M8x Housing material Metal, CuZn, chrome plated Material active face plastic, pa2-gf30 Connection Connector, M2x Vibration resistance 55 Hz ( mm) Shock resistance 30 g ( ms) protection Ip 67 Power on Indication Read/write head off TAG with air interface LED solid LED.5 Hz LED 3 Hz Wiring Maximum cable length 50 m Pinout Mating Cordset: RK 4.5T-*-RS 4.5T/S250

18 Industrial Automation Associated Data Carrier Housing Fig. Part Number ID Number Read/Write Range Zone Width Distance Length minimum between two read/write heads Recomm. TW-R6-B28 M (6).57 (4).52 (3).55 (4).709 (8) TW-R20-B28 M (6) (4) (3) (6) (2) (84) 2 TW-R20-K2 M (5) (4) () () (8) Smaller intervals are possible by alternating switching the read/write heads on and off with software. 0 mm air gap required when mounting to ferrous metal. See accessories on page 26 for spacers. Ambient temperature: -25 to +85 C (-3 to +85 F).

19 TURCK RFID Products RFID System - Read/Write Head Ring Type, 32 mm High Plastic, ABS Non-flush Mountable Power Supply (24 VDC) and Function via BL ident Interfaces Connector (M2) eurofast, Connection via BL ident Connecting Cable Housing Part Number Function Principle TN-S32XL-H47 The BL ident read/write head (transceiver) is used to exchange data with the data carrier (TAG). Together they form an air interface whose size depends on the combination of transceiver and TAG. The data carriers are passive. When they enter the air interface of the transceiver, the power from the transceiver is transferred inductively and data transfer completed. BL ident TAGs on the following page can be combined with this BL ident transceiver. The read/write interval varies between in. (6-44 mm). All TAGs available with EEPROM or FRAM memory. Part Number ID Number Mounting Mode Ambient temperature Data Transfer Output function Operating frequency TN-S32XL-H47 M Non flush -25 to +70 C (-3 to +58 F) Inductive 4-wire, write/read 3.56 MHz Housing Ring type, S32 Ring inner diameter 00 mm Housing material Plastic Material active face Plastic, ABS, yellow Connection Connector, M2x Vibration resistance 55 Hz ( mm) Shock resistance 30 g ( ms) Protection IP 67 Pinout Power On Indication Read/write head off TAG with air interface LED solid LED.5 Hz LED 3 Hz Wiring Maximum cable length 50 m Mating Cordset: RK 4.5T-*-RS 4.5T/S250

20 Industrial Automation Associated Data Carrier Housing Fig. Part Number ID Number Read/Write Range Zone Width Distance Length minimum between two read/write heads Recomm. TW-R6-B28 M (3).630 (6) (63) (90) 4.73 (360) 2 2 TW-R20-B28 M (8) (82) (03) (42) 3 3 TW-R30-B28 M (45).866 (22) (90) 3.66 (93) (7) (468) 4 TW-R50-B28 M (44) (22) (53) (62) 4 2 TW-R20-K2 M (32).630 (6) (64) 2.93 (74) 3.70 (94) (376) 3 TW-R30-K2 M (40).787 (20) 3.89 (8) (84) 4.23 (07) (428) 5 4 TW-R50-K2 M (64).8 (30) (29) () (38) (552) 5 TW-R50-90-HT-B28 M (44) (22) (53) (62) 5 TW-R50-90-HT-K2 M (64).8 (30) (29) () (37) (552) Smaller intervals are possible by alternating switching the read/write heads on and off with software. 0 mm air gap required when mounting to ferrous metal. See accessories on page 26 for spacers. Ambient temperature: -25 to +85 C (-3 to +85 F); (-40 to +20 C (-40 to +40 F) for TW-R*-HT...).