READ/WRITE MODULES (RWM) RLS

Transcription

1 HOUSING M READ/WRITE DISTANCE mm* HF RFID SYSTEM READ/WRITE MODULES (RWM) RLS-- ü M Metal threaded housing ü Sensing face of PBTP ü Insensible to dirt ü IO-Link V. Mx ü x PNP output in SIO mode configurable ü RWM reconfigurable via a Master Tag SW Ø LED (x) Mx * Please refer to table page GENERAL DATA INTERFACE Carrier frequency. MHz Data transfer rate baud Compatible standard ISO 9 LED green on RWM live Maximum transmission speed. kbit/s LED green blinking IO-Link communication Read-write distance max. mm with RTP-- LED yellow on Transponder detected LED yellow blinking Transponder + IO-Link communication IO-Link ü ELECTRICAL DATA MECHANICAL DATA Supply voltage range (Ub)... VDC Protection degree IP No-load supply current (field off) ma Ambient temperature range TA* C Max. current consumption (no load) ma Storage temperature range TS** C Polling current ma Sensing face material PBTP Short-circuit protection ü Housing material Chrome-plated brass Voltage reversal protection ü Connector type M -pin Max. output current ma Weight (incl. nuts) g * Read/write operations possible ** Data retention and mechanical stability limit route du Pâqui - P.O. Box - CH Corminboeuf - Switzerland - Tel: + - Fax: + - Internet: info@contrinex.com

2 MOUNTING RECOMMENDATIONS CLEARANCE Read/write modules must not mutually influence each other. For this reason a minimum distance of x D between the devices must be observed. D D D sensing face mm metal free zone support WIRING DIAGRAM PIN ASSIGNMENT bk wh bu L+ C/Q Q L- Pin Signal Function L+ + V Q DO (tag presence or data comparison) L- OV C/Q SDCI/SIO (tag presence or data comparison) M IO-Link characteristics Value for RLS-- IO-Link Protocol. COM-Mode COM (. kbaud) Min. cycle time. ms Process data width in bytes Process data width out 9 bytes Profile Smart Sensor Profile SIO-Mode support Yes Port type A Memory request for data management bytes Device ID xab Vendor ID x route du Pâqui - P.O. Box - CH Corminboeuf - Switzerland - Tel: + - Fax: + - Internet: info@contrinex.com

3 CONFIGURATION PARAMETER (IO-LINK / SIO MODE) Index Sub Hex Name Access Data Type Value Default IDENTIFICATION Vendor Name R char [] Contrinex h Vendor Text R char [] h Product Name R char [] RLS-- Product ID R char [] h Product Text R char [] IO-Link RFID reader h Serial Number R char [] h Firmware Revision R char [].9. h Application Specific Tag R/W char [] <user string byte (variable length)> READER PARAMETER PROCESS DATA <vendor specific> Operating Mode R/W h Data Hold Time R/W : Scan UID : Scan User Data : Read / Write Command : No Hold Time : Hold Time ms : Hold Time ms h : Hold Time ms : Hold Time ms h : Hold Time ms Scan Address R/W Address to scan READER PARAMETER SIO h C/Q PIN SIO Operating Mode R/W : Presence Transponder : Compare Data : No SIO h C/Q SIO Data to compare H R/W uint Comparison value Byte to C/Q SIO Data to compare L R/W uint Comparison value Byte to h SIO Compare Data Address (C/Q & Q) R/W Comparison address for C/Q and Q (A valid address must be chosen) h Data Hold Time Output (C/Q & Q) R/W : No Hold Time : Hold Time ms : Hold Time ms h : Hold Time ms : Hold Time ms h : Hold Time ms h C/Q PIN SIO Polarity R/W h Q PIN SIO Operating Mode R/W : Output close if condition = true : Output open if condition = true : Presence Transponder : Compare data (C/Q must be also in compare data) : No SIO h Q SIO Data to compare H R/W uint Comparison value Byte to 9 h Q SIO Data to compare L R/W uint Comparison value Byte to A h Q PIN SIO Polarity R/W : Output close if condition = true : Output open if condition = true route du Pâqui - P.O. Box - CH Corminboeuf - Switzerland - Tel: + - Fax: + - Internet: info@contrinex.com

4 PROCESS DATA REPRESENTATION PROCESS DATA MODE SCAN UID MODE PROCESS DATA INPUT TAG ANT NB TAG UID UID UID UID UID UID UID UID TAG : ANT : NB TAG : UID : UID : = No tag present in front of the RWM = tag or more present in front of the RWM = RF field off = RF field on Number of tag in front of the RWM UID LSB UID MSB PROCESS DATA OUTPUT N_ANT TAG NB N_ANT : TAG NB : = Switch on RF field = Switch off RF field Index of tag to be printed in UID area (index from ) PROCESS DATA MODE SCAN USER DATA PROCESS DATA INPUT RDY ERR TAG ANT EXT Data / Error Code Data Data Data Extended Data Extended Data Extended Data Extended Data PROCESS DATA OUTPUT RDY : ERR : TAG : ANT : EXT : Data : Data / : = No data available yet = Memory scanned and data available = Memory scanned and no error = Memory scanned but error; = No tag present in front of the RWM = Tag present in front of the RWM = RF field off = RF field on = bytes data = bytes data User data LSB / Error Code User data MSB N_ANT N_ANT : = Switch on RF field = Switch off RF field route du Pâqui - P.O. Box - CH Corminboeuf - Switzerland - Tel: + - Fax: + - Internet: info@contrinex.com

5 PROCESS DATA MODE READ/WRITE PROCESS DATA INPUT RDY ERR TAG ANT EXT Data / Error Code Data Data Data Extended Data Extended Data Extended Data Extended Data RDY : ERR : TAG : ANT : EXT : Data : Data / : = No data available yet = Command executed and data ready for user = Command executed and no error = Command executed but error = No tag present in front of the RWM = Tag present in front of the RWM = RF field off = RF field on = bytes data = bytes data Read data LSB / Error Code Read data MSB Error Code Definition CommandNotSupported = FormatError = OptionNotSupported = CommandProblem = CommTagError = TagError = NoMomoryBloc = BlocProtected = PROCESS DATA OUTPUT 9 START N_ANT CMD EXT ADD Data Data Data Data Extended Data Extended Data Extended Data Extended Data START : N_ANT : CMD : EXT : ADD : Data : Data / : = Do not execute the command = Execute the command = Switch on RF field = Switch off RF field = No command = Read = Write = bytes data = bytes data Block address Write data LSB Write data MSB SYSTEM COMMAND (idx h ) Value hex Value dec Function h ParamDownloadStore Device Reset h Restore factory settings* *always do a reset after the restore of factory settings route du Pâqui - P.O. Box - CH Corminboeuf - Switzerland - Tel: + - Fax: + - Internet: info@contrinex.com

6 MASTER TAG CONFIGURATION For the RLS-- the IO-Link mode or the SIO (standard I/O mode) can be configured via IO-Link or via a Master Tag. For the configuration via a Master Tag a transponder (called Master Tag) will contain all the data used for the configuration. The structure of the data are explained in the table on page. There is a simple procedure to configure the RWM. Once all the data are written in the Master Tag you need to put it in front of the RWM sensing face to switch off the RWM power supply and to switch on again. The RWM will detect that it s a Master Tag and read all the data and configure the outputs accordingly. On the Contrinex webpage ( it is possible to download a software to setup the Master Tag via a Contrinex USB RWM. This program is called IO-Link Master Tag programmer. SIO MODE POSSIBILITIES If you use the RLS-- in a SIO mode you will have two main possibilities:. Presence Transponder: In this mode the output will switch if a transponder is in the field of the RWM.. Compare Data: In this mode the output will switch if the data red in the defined block memory of the transponder matches with the data stocked in the RWM. MASTER TAG To build a Master Tag it s possible to use any ISO9 chip with at least eight memory blocks with bits each. route du Pâqui - P.O. Box - CH Corminboeuf - Switzerland - Tel: + - Fax: + - Internet: info@contrinex.com

7 CONFIGURATION PARAMETER (IO-LINK / SIO MODE) Bloc + A:H Byte Offset Name Data Type Value Default Comment READER PARAMETER PROCESS DATA (IO-LINK MODE) Operating Mode : Scan UID : Scan User Data : Read / Write Command See process data organisation h h Data Hold Time : No Hold Time : Hold Time ms : Hold Time ms h : Hold Time ms : Hold Time ms h : Hold Time ms h h Scan Address Address to scan Addres to scan in user data READER PARAMETER SIO (SIO MODE) C/Q PIN SIO Operating Mode : Presence Transponder : Compare Data : No SIO h... h C/Q SIO Data to compare H uint Comparison value Byte to Ext. Data Ext. Data Ext. Data Ext. Data h... h C/Q SIO Data to compare L uint Comparison value Byte to Data Data Data Data C h Address (C/Q & SIO Compare Data Q) Comparison address for C/Q and Q (A valid address must be chosen) h D h Output (C/Q & I/ Data Hold Time Q) : No Hold Time : Hold Time ms : Hold Time ms h : Hold Time ms : Hold Time ms h : Hold Time ms h E h C/Q PIN SIO Polarity : Output close if condition = true : Output open if condition = true h F h Q PIN SIO Operating Mode : Presence Transpondere : Compare Data : No SIO h... Q SIO Data to compare H uint Comparison value Byte to Ext. Data Ext. Data Ext. Data Ext. Data h... h Q SIO Data to compare L uint Comparison value Byte to Data Data Data Data h h Q PIN SIO Polarity : Output close if condition = true : Output open if condition = true CRC h... C h CRC CHECK uint CRC on all config field with polynom: X +X +X +X +X +X +X + X +X +X +X +X +X +X +X route du Pâqui - P.O. Box - CH Corminboeuf - Switzerland - Tel: + - Fax: + - Internet: info@contrinex.com

8 POSSIBLE COMBINATION AND TYPICAL DISTANCE - RLS-- Transponder type S max S D Ø 9 RTP-9-9. Ø RTP--. 9 Ø RTP-- 9 Ø RTP-- 9 Ø RTP-- Ø RTP-- Read/Write Module Working area Transponder D RLS- - y x S S max AVAILABLE TYPES Part number Part reference Ø Mounting Connection RLS-- M Non-embeddable M -pin Operators of the products we supply are responsible for compliance with measures for the protection of persons. The use of our equipment in applications where the safety of persons might be at risk is only authorized if the operator observes and implements separate appropriate and necessary measures for the protection of persons and machines. Terms of delivery and rights to change design reserved. route du Pâqui - P.O. Box - CH Corminboeuf - Switzerland - Tel: + - Fax: + - Internet: info@contrinex.com RLS-- YAG