LQSE-4S8-120-D. 120 V~ 50 / 60 Hz 16 A. lutron.com LQSE-4S8-120-D. Dimming Power Module. Option. Input. Opt Def H M

Transcription

1 Input Entrada Entrée Ta > 70 C Prog Option 120 V~ Def 50 / 60 Hz Opt1 10 A Opt2 Opt3 lutron.com H Switching Power odule Switching Power odule b The DI Power odule (DP) family is a group of modular products for the control of lighting loads. This product is compatible with utron systems. This document describes the following product: : 4-zone power module for switching only. lutron.com UTRO1 CCO, 1/3 HP Features Four switched output zones. Adaptive zero-cross switching maximizes relay life. Rated for lighting loads as defined by U 508, EA 410, as well as IC, V, and EV. Rated for motor loads of 1/3 HP. Includes QS link for seamless connection to a system. EDs on the module provide diagnostic information. Buttons on module provide override control. anual Override Contact Closure Input (). Programmable Contact Closure Output (CCO). Power failure memory automatically returns the outputs to the levels they were set to prior to a power outage. System Example HomeWorks QS Panel Dimming Power odule QS Contact Closure Interface GRAFIK Eye QS Contact Closure Output 400 W 250 W 250 W 250 W Zn 1 Zn 2 Zn 3 Zn 4 anual Override Contact Closure Input Input Hi Temp Prog Power QSE-4A-120-D Opt Def H Switching Power odule lutron.com UTRO1 CCO, 1/3 HP Palladiom Keypad QS ink Sivoia QS Shades/ Draperies 7 Up to 100 QS devices Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:

2 Switching Power odule Specifications b Regulatory Approvals Complies with cuus O Certified utron Quality Systems registered to ISO Power 120 V~ 50/60 Hz Single input feed 16 A maximum input current ightning strike protection meets ASI/IEEE standard C Can withstand voltage surges up to 6000 V~ and current surges up to 3000 A. For ungrounded delta feed applications, contact utron. Environment For thermal specifications, see ounting section Relative humidity: less than 90% non-condensing For indoor use only Terminals ains wiring: 18 AWG to 12 AWG (1.0 mm² to 2.5 mm²) / CCO wiring: 20 AWG to 12 AWG (0.5 mm² to 2.5 mm²) 22 AWG to 16 AWG (0.5 mm² to 1.5 mm²) (two wires, solid or stranded) Zone wiring: 18 AWG to 12 AWG (1.0 mm² to 2.5 mm²) QS ink: 20 AWG to 12 AWG (0.5 mm² to 2.5 mm²) 22 AWG to 18 AWG (0.5 mm² to 1.0 mm²) (two wires, solid or stranded) anual Override Contact Closure Input () When the is open, the Switching Power odule will enter anual Override ode, which will turn on all loads and disable control of all local zones and QS devices. Default operation can be modified through programming software. When the is closed or jumpered (factory default), the Switching Power odule zones will return to the settings they were at prior to entering anual Override ode. Contact Closure Output (CCO) Accepts voltages of 0 24 V~ / 0 24 V-; see chart below for load switching capacities: Switching Voltage Resistive oad R 0 24 V- 1.0 A 0 24 V~ 0.5 A Provides both normally open (.O.) and normally closed (.C.) dry contacts. aintained or momentary output type. Output relay is non-latching (if relay is closed and power is lost, relay will open). The CCO is not rated to control unclamped, inductive loads. Inductive loads include, but are not limited to, relays, solenoids, and motors. To control these types of equipment, a flyback diode (not included) must be used (DC voltages only). See diagram below. Flyback Diode (required for inductive loads) Inductive oad + anual ode Operation Zone button on the unit can be used to turn loads on and off..o. CCO Output.C. 24 V- maximum Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:

3 Switching Power odule Specifications - (continued) b Programming and Compatibility Requirements Setup and programming of the Switching Power odule is done through the programming software. software version 12.0 or higher required. Wallstations wallstations can be configured to control Switching Power odules with the programming software. Wallstation ED indicators display the status of programmed lights. QS ink imits A QS link in a system can have up to 512 zones (outputs) and 100 devices (required processor counts as one device on the QS link). Each Switching Power odule counts as one device toward the 100 device limit, and 4 zones toward the 512 zone limit. Output Zone Ratings Each zone is rated at 8 A for switching. Rated for resistive, inductive, or capacitive lighting loads as defined by EA 410. Air gap off per output. o minimum load per output. This module is designed to control loads with ratings as noted in the table below. Outputs cannot be used to control general purpose receptacles. Relay Ratings oad Type 120 V~ Tungsten AC General Use Electric Discharge amp Electronic Ballast (EA 410) Resistive Inductive 8 A (1/3 HP)/zone, otor 16 A max/module Special considerations: When controlling lamps, utron recommends using permanently installed fixtures. If controlling plug-in lamps, installation must ensure a method of preventing non-rated loads being plugged into the unit. An example is utron P/ CAR-15-DDTR, which is a dedicated receptacle with an alternate plug type. Controlling loads outside the parameters listed in the specifications may damage the device and void the warranty. If attempting to control general purpose receptacles, use the appropriate third-party power pack for the rated load. Run a separate neutral for each load circuit. A common neutral connection is not recommended. Unit may be powered by Ground Fault Interrupter (GFI) or Arc Fault Circuit Interrupter (AFCI) protected circuit if required. For applications requiring higher wattage ratings, use PHP-SW-DV-WH or GRX-TVI for 120 V~. Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:

4 echanical Dimensions Switching Power odule b lutron.com UTRO1 CCO, 1/3 HP 3.53 in (89.7 mm) 2.38 in (60.6 mm) 6.37 in (161.7 mm) ounting ount in a utron DI Panel (see spec at or in a EA Type 1 rated consumer panel or breaker panel with integrated DI rail. Unit is 9 DI modules (6.37 in [161.7 mm]) wide. ount in an accessible and serviceable location. Unit may be mounted by pressing the unit onto the DI rail with the clips locked. To remove the unit from the DI rail, unlock the clips using a screwdriver. See utron P / at for more information on mounting and installation in panels with integrated DI rail. ount the Power odule where audible noise is acceptable (internal relays click). Unit generates heat, maximum 24 BTUs/hr. ount unit such that all the conditions below are met: Room ambient temperature is between 32 ºF and 104 ºF (0 ºC and 40 ºC). Temperature inside mounting panel, within 0.80 in (20 mm) of unit, is between 32 ºF and 104 ºF (0 ºC and 40 ºC). Calibration point maximum: 149 ºF (65 ºC). lutron.com UTRO1 CCO ounting clips (4) on unit ocked Unlocked, 1/3 HP Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:

5 Switching Power odule Wiring: ains and Output Zones Wiring from Distribution to Switching Power odule Turn off all circuit breakers or isolators feeding the Switching Power odule at the distribution panel. Run line / hot and neutral wires from a 120 V~ 50 / 60 Hz feed to the Switching Power odule unit. Run a separate neutral for each load circuit. A common neutral connection is not recommended. ains Wiring and EC Class 2 Separation Follow appropriate local and national codes to avoid violating required separation guidelines b EC Class 2 CCO QS ink lutron.com UTRO1 CCO, 1/3 HP ains eutral Outputs V~ 1 Distribution Panel 120 V~ ine / Hot eutral To additional modules ote: If wiring for feed-through to other utron modules using mains terminals, total current of all modules must be less than or equal to 16 A. Zone 1 Zone 2 Zone 3 Zone 4 Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:

6 Switching Power odule Wiring: anual Override Contact Closure Input and Contact Closure Output EC Class 2 Contact Closures anual Override Contact Closure Input ()/Contact Closure Output (CCO) wiring is EC Class 2. Follow all applicable national and local codes for proper circuit separation and protection. Turn off all breakers or isolators feeding the Switching Power odule at distribution panel before servicing unit. is local control only and cannot control other units over the QS link. on up to 32 units may be connected to an emergency or manual override device in parallel if event is intended to affect multiple units. When in anual Override ode: All zone outputs will be switched on. Controls will not affect units in anual Override ode. Controls connected to a unit in anual Override ode will continue to affect units on the link that are not in anual Override ode. anual override contact closure input is normally closed (.C.). The Switching Power odule is shipped with a jumper pre-installed. ote: The Switching Power odule will default to anual Override ode if the is left open. If no anual Override contact input is required, leave the wire jumper in the terminals. Pre-installed Jumper Wiring OR CCO Third-party Device lutron.com UTRO1 Device Wiring CCO CCO CCO Device Wiring CCO Wiring CCO, 1/3 HP b O. Wiring OR.C. Wiring CCO (.O.) CCO (.C.) CCO CCO Third-party Device Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:

7 Switching Power odule Wiring: QS ink QS link wiring is ECR class 2. Follow all applicable local codes for proper circuit separation and protection. Turn off all breakers or isolators feeding the Switching Power odule at distribution panel before servicing unit. Wiring may be daisy chained or t-tapped. Total length of QS link wiring must not exceed 2000 ft (610 m). Wire Gauge: Control (terminal 1): 18 AWG (1.0 mm 2 ). Data (terminals 3 and 4): 1 pair 22 AWG to 18 AWG, (0.5 mm 2 to 1.0 mm 2 ) twisted and shielded. Can use utron cable GRX-CB-346S-500 (less than 500 ft [150 m]) or GRX-CB-46 (500 ft to 2000 ft [150 m to 610 m]). See Wiring Guidelines application note on 1: Control ink 2: Do ot Connect 3: Data ink 4: lutron.com UTRO1 CCO b , 1/3 HP )utron, utron, HomeWorks, Sivoia, Palladiom, and GRAFIK Eye are trademarks of utron Electronics Co., Inc., registered in the U.S. and other countries. U is a trademark of U C. EC is a registered trademark of the ational Fire Protection Agency, Quincy, assachusetts. Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber: