Series EX600. Fieldbus System EX600 S DN. SI Unit. How to Order. Specifications. SI Unit. SI Unit COM. 1 PNP ( COM.) 2 NPN (+COM.)

Transcription

1 Fieldbus System Series EX600 SI Unit How to Order EX600 S DN SI Unit Fieldbus protocol DN DeviceNet TM MJ CC-Link PR PROFIBUS DP SI Unit COM. PNP ( COM.) NPN (+COM.) EX600-SDN EX600-SMJ EX600-SPR Specifications Communication Valve output Environmental resistance Model EX600-SDN EX600-SDN EX600-SMJ EX600-SMJ EX600-SPR EX600-SPR DeviceNet TM CC-Link PROFIBUS DP Protocol Volume (Edition.) (Ver..0, Ver..00) (DP-V0) Volume (Edition.) Device type Group Only Server Remote Device Station DP Slave Communication speed Configuration file I/O occupation area (Inputs/Outputs) Terminator DeviceNet TM power supply Internal current consumption (Power supply for Control and Input) Output type Number of outputs Load Fail safe Protection Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation resistance Standards Mass Vibration resistance Impact resistance /0/00 kbps Max. ( inputs/ outputs) 6/6 kbps.//0 Mbps EDS file GSD file Max. ( inputs/ outputs) /// stations to VDC Max. ( inputs/ outputs) Internally implemented ma or less 7 ma or less 80 ma or less PNP NPN PNP NPN PNP NPN outputs (8/6// outputs selectable) Solenoid valve with light/surge voltage suppressor VDC,. W or less (SMC) HOLD/CLEAR Short-circuit protection IP67 (Manifold assembly) 0 to 0 C to 8% RH (No dew condensation) 00 VAC for minute between external terminals and FE 00 VDC, 0 MΩ or more between external terminals and FE 0 to 7 Hz with constant amplitude of 0.7 mm p-p 7 to 0 Hz with constant acceleration of 9 m/s for hours in each direction of X, Y and Z direction (During de-energizing) 7 m/s times in each direction of X, Y and Z (During de-energizing) CE marking, UL (CSA) recognition 00 g 9.6/9././9.7/ 87./00 kbps.//6/ Mbps

2 Fieldbus System Series EX600 Parts Description q w e r t!!0 o y u i No Description Status indication LED Indication cover Indication cover set screw Connector (BUS OUT) Marker groove Connector (for Handheld Terminal) Valve plate mounting holes Valve plate mounting groove Joint bracket Connector for unit (Plug) Connector (BUS IN) Dimensions

3 Series EX600 Digital Input Unit How to Order EX600 DX ND Digital Input Unit Input type P PNP N NPN EX600-DX B EX600-DX C/C EX600-DX D Specifications Connector, number of inputs, and open circuit detection Symbol B C C D Connector x M ( pins) 8 x M8 ( pins) 8 x M8 ( pins) 8 x M ( pins) Number of inputs Open circuit detection 8 inputs No 8 inputs No 8 inputs Yes 6 inputs No Input specifications Environmental resistance Model EX600-DXPB EX600-DXNB Input type Input connector Number of inputs Sensor supplied voltage Maximum sensor supplied voltage Protection Input resistance Rated input current ON voltage/on current OFF voltage/off current Open Note ) circuit detection current Current consumption Indicator Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation resistance Vibration resistance Impact resistance Standards Mass wires wires EX600-DXPC EX600-DXNC EX600-DXPD EX600-DXND PNP NPN PNP NPN PNP NPN M ( pins) Note ) M8 ( pins) 8 inputs ( inputs/connector) 8 inputs ( input/connector) 6 inputs ( inputs/connector) VDC (Supplied from power supply for control and input) 0. A/connector A/unit Short-circuit protection.7 kω 9 ma or less 7 V or more / ma or more (At NPN input, between the pin for input terminal and for sensor supplied voltage of + V) (At PNP input, between the pin for input terminal and for sensor supplied voltage of 0 V) V or less / ma or less (At NPN input, between the pin for input terminal and for sensor supplied voltage of + V) (At PNP input, between the pin for input terminal and for sensor supplied voltage of 0 V) 0 ma or less Note ) M ( pin) connector can be connected. Note ) Applicable only for unit with open circuit detection function A/connector A/unit 0. ma or less/input Note ) 0. ma or less/connector Note ) ma or less IP67 (Manifold assembly) 0 to 0 C to 8% RH (No dew condensation) 00 VAC for minute between external terminals and FE 00 VDC, 0 MΩ or more between external terminals and FE 0 to 7 Hz with constant amplitude of 0.7 mm p-p 7 to 0 Hz with constant acceleration of 9 m/s for hours in each direction of X, Y and Z direction (During de-energizing) 7 m/s times in each direction of X, Y and Z (During de-energizing) CE marking, UL (CSA) recognition M ( pins) Note ) 0. A/connector A/unit 70 ma or less Green LED on (When input is ON.) Red LED on (When short circuit is detected at sensor s power supply.) Red LED flashing (ON/OFF counter is exceeded, or open circuit is detected. Note ) ) 00 g 7 g 0 g

4 Fieldbus System Series EX600 Parts Description EX600-DX B q w e No. Description Status indication LED Connector (Input) Marker groove Joint bracket Connector for unit (Plug) Connector (Input) Pin Assignment t Pin No. Signal name V (for control/input) Input w 0 V (for control/input) Input q FE r EX600-DX C q w e No. Description Status indication LED Connector (Input) Marker groove Joint bracket Connector for unit (Plug) Connector (Input) Pin Assignment t Pin No. Signal name V (for control/input) 0 V (for control/input) Input r EX600-DX D q w e No. Description Status indication LED Connector (Input) Marker groove Joint bracket Connector for unit (Plug) Connector (Input) Pin Assignment t Pin No. Signal name V (for control/input) Input w 0 V (for control/input) Input q FE r 8

5 Series EX600 Dimensions EX600-DX B EX600-DX C

6 Fieldbus System Series EX600 EX600-DX D

7 Series EX600 Digital Output Unit How to Order EX600 DY P B Digital Output Unit Connector and number of outputs Symbol Connector Number of outputs B x M ( pins) 8 outputs Output type P PNP N NPN Specifications Output specifications Model Output type Output connector Number of outputs Rated load voltage Maximum load current Protection Current consumption Indicator Environmental resistance Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation resistance Vibration resistance Impact resistance Standards Mass EX600-DYPB EX600-DYNB PNP NPN M ( pins) 8 outputs ( outputs/connector) VDC (Supplied from power supply for output) 0. A/ output, A/unit Short-circuit protection 0 ma or less Green LED on (When output is ON.) Red LED on (When short circuit is detected at load.) Red LED flashing (Open circuit is detected, or ON/OFF counter is exceeded.) IP67 (Manifold assembly) 0 to 0 C to 8% RH (No dew condensation) 00 VAC for minute between external terminals and FE 00 VDC, 0 MΩ or more between external terminals and FE 0 to 7 Hz with constant amplitude of 0.7 mm p-p 7 to 0 Hz with constant acceleration of 9 m/s for hours in each direction of X, Y and Z direction (During de-energizing) 7 m/s times in each direction of X, Y and Z (During de-energizing) CE marking, UL (CSA) recognition 00 g

8 Fieldbus System Series EX600 Parts Description q w e No. Description Status indication LED Connector (Output) Marker groove Joint bracket Connector for unit (Plug) Connector (Output) Pin Assignment t Pin No. Signal name EX600-DYPB EX600-DYNB NC V (for output) Output w Output w 0 V (for output) NC Output q Output q FE FE r Dimensions

9 Series EX600 Analog Input Unit How to Order EX600 AX A Analog Input Unit Connector and input channel Symbol Connector Input channel A x M ( pins) channels Specifications Input specifications Model Input type Input connector Input channel Sensor supplied voltage Maximum sensor supplied voltage Protection Input signal range Maximum input signal Input impedance Linearity Repeatability Absolute accuracy Current consumption Indicator Environmental resistance Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation resistance Vibration resistance Impact resistance Standards Mass bit resolution 6 bit resolution Voltage input EX600-AXA M ( pins) channels ( channel/connector) Note) VDC (Supplied from power supply for control and input) 0. A/channel Short-circuit protection 0 to 0 V to V 0 to V 0 to 0 V (Factory default setting) to V ± V 00 kω ±0.% F.S. or less ±0.0% F.S. or less ±0.% F.S. or less 70 ma or less Current input 0 to 0 ma to 0 ma 0 to 0 ma ±0 ma 0 Ω ±0.6% F.S. or less Green LED on (When input is ON.) Red LED on (When short circuit is detected at sensor s power supply.) Red LED flashing (Analogue input exceeds measurement range or user setting range.) IP67 (Manifold assembly) 0 to 0 C to 8% RH (No dew condensation) 00 VAC for minute between external terminals and FE 00 VDC, 0 MΩ or more between external terminals and FE 0 to 7 Hz with constant amplitude of 0.7 mm p-p 7 to 0 Hz with constant acceleration of 9 m/s for hours in each direction of X, Y and Z direction (During de-energizing) 7 m/s times in each direction of X, Y and Z (During de-energizing) CE marking, UL (CSA) recognition 90 g Note) channels are occupied per one unit. Considering influence of noise, etc. from outside source to the Analog Input Unit, when connecting a sensor that has ground connected at one end (SMC sensor uses this method), please connect sensor s ground line to unit connector s Input ( ) terminal.

10 Fieldbus System Series EX600 Analog Characteristics Offset Binary Data Format AD value AD value AD value 90 (FD) 868 (FC) 6976 (F9E8) 8 (E) 60 (68) 0 a Input 0 a b Input a 0 b Input Input signal range a Input signal range a b Input signal range a b 0 to 0 V 0 V to V V V 0 to 0 V 0 V 0 V 0 to V V to 0 ma ma 0 ma to V V V 0 to 0 ma 0 ma 0 to 0 ma 0 ma 0 ma Regarding AD value In the above graph, AD values are explained as below. 90 : AD value [Decimal value] (FD): Offset Binary type [Hexadecimal value] Signed Binary & s Complements Data Format 90 (79E) (79E) AD value 9 (78E) (78E) AD value 08 (79E8) (79E8) AD value a 0 b Input 0 a Input (7) (7) 0 a b Input 08 (F9E8) (868) Input signal range a Input signal range a b Input signal range a b 0 to 0 V 0 V to V V V 0 to 0 V 0 V 0 V 0 to V V to 0 ma ma 0 ma to V V V 0 to 0 ma 0 ma 0 to 0 ma 0 ma 0 ma Regarding AD value In the above graph, AD values are explained as below. 08 : AD value [Decimal value] (F9E8): Signed Binary type [Hexadecimal value] (868) : s complements [Hexadecimal value]

11 Series EX600 Parts Description q w e No. Description Status indication LED Connector (Analog input) Marker groove Joint bracket Connector for unit (Plug) Connector (Analog Input) Pin Assignment t r Pin No. Signal name V (for control/input) Input + 0 V (for control/input) Input FE When connecting analogue input device, wiring method differs depending on which type of sensor is used. Refer to below diagram for wiring method example. Especially when connecting [-wire output type sensor] and [-wire current output type sensor], short the pin no and the pin no. Otherwise, it will not be correctly detected. When -wire output type sensor is used Analog Input Unit V : V (for control and input) Output : Input (+) Sensor 0V : 0 V (for control and input) Short : Input ( ) FE : FE Compatible SMC Products Pressure sensor: Series PSE Series PSE Series PSE0 Series PSE6 Flow sensor: Series PFM Series PFMV Series PFA Series PFD Series PFW When -wire current output type sensor is used Analog Input Unit V : V (for control and input) Output : Input (+) Sensor Short : 0 V (for control and input) : Input ( ) FE : FE Compatible SMC Products Pressure sensor: Series PSE0-8 Series PSE When -wire output type sensor is used Analog Input Unit Sensor V Output (+) 0V Output ( ) FE : V (for control and input) : Input (+) : 0 V (for control and input) : Input ( ) : FE

12 Fieldbus System Series EX600 Dimensions

13 Series EX600 End Plate EX600 End Plate on D side How to Order ED Connector M ( pins) 7/8 inch ( pins) Mounting method Nil No DIN rail mounting plate With DIN rail mounting plate for manifold solenoid valve EX600-ED EX600-ED Specifications Input Environmental resistance specifications Model Power connector Power supply for control/input Power supply for output Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation resistance Vibration resistance Impact resistance Standards Mass EX600-ED M ( pins) plug VDC ±0% Max. supply current A VDC +0%/ % Max. supply current A EX600-ED 7/8 inch ( pins) plug VDC ±0% Max. supply current 8 A VDC +0%/ % Max. supply current 8 A IP67 (Manifold assembly) 0 to 0 C to 8% RH (No dew condensation) 00 VAC for minute between external terminals and FE 00 VDC, 0 MΩ or more between external terminals and FE 0 to 7 Hz with constant amplitude of 0.7 mm p-p 7 to 0 Hz with constant acceleration of 9 m/s for hours in each direction of X, Y and Z direction (During de-energizing) 7 m/s times in each direction of X, Y and Z (During de-energizing) CE marking, UL (CSA) recognition 70 g 7 g Parts Description EX600-ED q Not used EX600-ED q w w 7 No. r w e Description Power connector Fixing hole for direct mounting DIN rail fixing hole FE terminal No. r w e Description Power connector Fixing hole for direct mounting DIN rail fixing hole FE terminal

14 Fieldbus System Series EX600 Dimensions EX600-ED EX600-ED

15 Series EX600 Handheld Terminal EX600 HT Handheld Terminal Cable length for Handheld Terminal Nil No cable m m Option When option item is needed separately, please order using below part number. Description Handheld Terminal cable m Handheld Terminal cable m How to Order Model EX600-AC00- EX600-AC00- Specifications Model Communication method Baud rate Power supply Current consumption Display Resolution Connector Environmental resistance Protective structure Operating temperature Operating humidity Withstand voltage Insulation resistance Vibration resistance Impact resistance Standard Mass EX600-HT RSC 9600 bps Power supplied from SI Unit connector ( VDC) 0 ma or less LCD with backlight 8 x 6 dots -pin connector IP0 0 to 0 C to 8% RH (No dew condensation) 00 VAC for minute between external terminals and frame 00 VDC, 0 MΩ or more between external terminals and frame 0 to 7 Hz: Constant amplitude 0.7 mm p-p 7 to 0 Hz: Constant acceleration 9 m/s for hours in each direction (During de-energizing) 00 m/s times for each X, Y, Z direction (During de-energizing) CE marking 60 g Dimensions 70 (9.6)

16 Fieldbus System Series EX600 Parts Description q t r e w No. Description LCD display Operation button Connector Handheld Terminal cable Status display LED Operation Button and LED Details u q y t r e w No. 6 7 Description ENTER button Cursor button F button F button Escape button ERROR status LED POWER status LED 0

17 Series EX600 Accessories 7. Power supply cable with M connector. Seal cap (M8) 9. I/O cable with connector 8. Communication cable with connector. Marker. Valve plate. Seal cap (M) 6. Power supply cable with 7/8 inch connector. Reinforcing brace (for direct mounting). End plate bracket. Reinforcing brace (for DIN rail mounting) 6. 7/8 inch fieldwireable connector. End plate bracket This bracket is used for the end plate of DIN rail mounting. EX600-ZMA. Valve plate EX600-ZMV Enclosed parts Round head screw (M x 0) P-tight screw ( x ) pc. pcs. Enclosed parts Round head screw (M x 6) Round head screw (M x 8) pcs. pcs.. Reinforcing brace This bracket is used on the bottom of the unit at the intermediate position for connecting 6 or more units. For direct mounting EX600-ZMB For DIN rail mounting EX600-ZMB Enclosed parts Round head screw (M x ) pcs. Enclosed parts Round head screw (M x 6) pcs.

18 Fieldbus System Series EX600. Seal cap (0 pcs.) The seal cap needs to be placed the unused I/O connector. The specified protection cannot be maintained.. Marker ( sheet, 88 pcs.) The signal name of I/O device and each unit address can be entered and mounted on each unit. EX600-ZT EX9-AWES For M8 EX9-AWTS For M 6. 7/8 inch connector and its related parts Power supply cable with 7/8 inch connector PCA-880 Straight m PCA-88 Straight 6 m PCA-886 Right angle m PCA-889 Right angle 6 m SPEEDCON and its related parts 7. Power supply cable with M connector ( pins B-coded) PCA-697 Straight m PCA-690 Straight 6 m PCA-69 Right angle m PCA-6969 Right angle 6 m 7/8 inch fieldwireable connector [compatible to AWG-6] PCA-8797 Plug PCA-8807 Socket Note) For M connector, description of A-coded for a normal type and B-coded for a reverse type is used as a connector shape respectively. 8. Communication cable with connector / Communication connector The communication cable with connector and communication connector available to this series are found in page through to I/O cable with connector / I/O connector The I/O cable with connector and I/O connector available to this series are found in page 7 through to 9.

19 Communication Cable/Connector M Example of Connection PLC 9 Connected at the end Serial wiring with Input/Output unit Solenoid valve manifold Discrete and decentralized serial wiring GW unit Series EX600 Specifications Series EX00 Part no. Description Communication cable (With one side connector) Fieldwireable connector Terminal plug PCA-76 PCA-766 PCA-769 PCA-766 PCA Product image Number of functional poles Key type Pin assignment Wiring specifications Note) Rating/Performance Material Fixed cable length Cable O.D. Wire gauge Power pair (Stranded wire cross section) Data pair Wire outer diameter Power pair (Including insulating material) Data pair Connection type Rated current Rated voltage Contact resistance Insulation resistance Withstand voltage Ambient Connector temperature Operating Cable Fixed Protection class Allowable repeated insertion/withdrawal Cable retaining force Vibration resistance Material of knurl Contact (Surface treatment) Insulating material Material of sheath Socket Plug Plug Socket Plug, A-coded Socket, A-coded (Viewed from the plug/socket side) m 6.70 ±0. mm 0. mm /AWG 0. mm /AWG. ±0.0 mm.0 ±0.0 mm to 90 C 0 to 7 C 0 to 80 C 0 N/ sec. Zinc for die casting Thermoplastic polyurethane (TPU) Polyurethane (PUR) M: poles DeviceNet TM : DRAIN : V+ (Red) : V (Black) : CAN H (White) : CAN L (Blue) For DeviceNet TM (Plug, A-coded) : DRAIN: NC : V+: NC : V : NC : CAN H : CAN L Weight (Mass) Approx. 08 g Approx. 06 g Approx. 7 g Approx. g Approx. g Note) The shaded parts show the specifications for the applicable cable. Adaptation for the connector may vary on account of the conductor construction of the electric wire. A 00 MΩ.0 kv Applicable cable 8 V mω 00 CuSn (Au plating (Ni plating)).0 to 8.0 mm 0. to 0. mm /AWG6 to 0 Spring-cage connection 0 to 8 C IP67 (Only with screw tightened) 0 to 00 Hz/98 m/s Brass Polyamide (PA6.6) Ω to 90 C Zinc for die casting Thermoplastic polyurethane (TPU)

20 Communication Cable/Connector M Example of Connection PLC Serial wiring with Input/Output unit Solenoid valve manifold OUT side IN side OUT side IN side Discrete and decentralized serial wiring GW unit Series EX600 Specifications Series EX00 Part no. Description Communication cable (With one side connector) Fieldwireable connector PCA-6770 PCA-6777 PCA-767 PCA-760 Product image Number of functional poles Key type Pin assignment Wiring specifications Note) Rating/Performance Material Fixed cable length Cable O.D. Wire gauge (Stranded wire cross section) Wire outer diameter (Including insulating material) Connection type Rated current Rated voltage Contact resistance Insulation resistance Withstand voltage Ambient Connector temperature Operating Cable Fixed Protection class Allowable repeated insertion/withdrawal Cable retaining force Vibration resistance Material of knurl Contact (Surface treatment) Insulating material Material of sheath Weight (Mass) Socket Approx. 06 g Plug Plug Socket M: poles Plug, A-coded Socket, A-coded (Viewed from the plug/socket side) m 7.7 ±0. mm 0. mm /AWG0. ±0.07 mm 0 V to 90 C 0 to 60 C 0 to 60 C 0 N/ sec. Zinc for die casting Thermoplastic polyurethane (TPU) Polyvinyl chloride (PVC) Approx. 08 g Approx. 8 g : SLD (Shield wire) : DB (White) : DG (Yellow) : DA (Blue) Approx. g Note) The shaded parts show the specifications for the applicable cable. Adaptation for the connector may vary on account of the conductor construction of the electric wire. A mω 00 MΩ. kv IP67 (Only with screw tightened) 00 Applicable cable 0 to 00 Hz/98 m/s CuSn (Au plating (Ni plating)).0 to 8.0 mm 0. to 0. mm /AWG6 to 0 Spring-cage connection 8 V 0 to 8 C Brass Polyamide (PA6.6)

21 Communication Cable/Connector M Example of Connection PLC A product connected at the end Serial wiring with Input/Output unit Solenoid valve manifold 0 Discrete and decentralized serial wiring GW unit IN side 0 OUT side Series EX600 Specifications Series EX00 Part no. Description Communication cable (With one side connector) Fieldwireable connector Terminal plug PCA-7688 PCA-769 PCA-770 PCA-77 PCA Product image Number of functional poles Key type Pin assignment Wiring specifications Note) Rating/Performance Material Fixed cable length Cable O.D. Wire gauge (Stranded wire cross section) Connection type Rated current Rated voltage Contact resistance Insulation resistance Withstand voltage Ambient Connector temperature Operating Cable Fixed Protection class Allowable repeated insertion/withdrawal Cable retaining force Vibration resistance Material of knurl Contact (Surface treatment) Insulating material Material of sheath Socket Plug Plug Socket M: poles M: poles B-coded (Reverse key) : : A Line (Green) : Plug, B-coded Plug, B-coded : B Line (Red) : (Viewed from the plug/socket side) m 7.80 ±0. mm Applicable.0 to 8.0 mm 0. mm /AWG cable 0. to 0. mm /AWG6 to 0. ±0.07 mm Spring-cage connection 60 V to 90 C 0 to 80 C 0 to 8 C 0 N/ sec. Zinc for die casting Polyurethane (PUR) For PROFIBUS DP (Plug, B-coded) M: poles : VP : B Line : A Line : DGND Weight (Mass) Approx. g Approx. 6 g Approx. 8 g Approx. g Approx. g Note) The shaded parts show the specifications for the applicable cable. Adaptation for the connector may vary on account of the conductor construction of the electric wire. Wire outer diameter (Including insulating material) A 00 MΩ. kv mω 8 V 0 to 8 C IP67 (Only with screw tightened) 00 0 to 00 Hz/98m/s Brass CuSn (Au plating (Ni plating)) Polyamide (PA6.6) 60 V 90 Ω 0 Ω 90 Ω to 90 C Zinc for die casting Thermoplastic polyurethane (TPU)

22 Communication Cable/Connector Dimensions Communication cable (With one side connector) PCA-6770 For CC-Link (Socket) Socket connector pin assignment ø.8. M SPEEDCON ø Terminal no. Wiring Cable wire colors :SLD White: DB Yellow: DG Blue: DA PCA-6777 For CC-Link (Plug) Plug connector pin assignment ø.8 7. M SPEEDCON ø PCA-76 For DeviceNet TM (Socket) Socket connector pin assignment ø.8. M SPEEDCON ø Terminal Cable wire no. colors : DRAIN Red: V+ Black: V White: CAN H Wiring 6 Blue: CAN L PCA-766 For DeviceNet TM (Plug) Plug connector pin assignment ø.8 7. M SPEEDCON ø Terminal Cable wire no. colors : Green: A Line : Red: B Line : Shield line is connected to the knurl. Wiring Fieldwireable connector 0 PCA-7688 For PROFIBUS DP (Socket) PCA-769 For PROFIBUS DP (Plug) Socket connector pin assignment B-coded (Reverse key) Plug connector pin assignment B-coded (Reverse key) 60 8 ø9 ø7 ø9 ø7 ø.8 ø.8. M SPEEDCON 7. M SPEEDCON Plug Socket PCA PCA-769 PCA-770 PCA PCA-766 PCA-77 For CC-Link For DeviceNet TM For PROFIBUS DP For CC-Link For DeviceNet TM For PROFIBUS DP ø7.8 ø A-coded (Normal key) B-coded (Reverse key) M SW6 A-coded (Normal key) B-coded (Reverse key) M SW6 Terminal plug 9 PCA-767 Terminal resistor for DeviceNet TM ø.8 6. M.8 PCA-777 Terminal resistor for PROFIBUS DP ø.8 6. M.8 6

23 Between Sensor/Switch and Input Device Fieldwireable Connector Specifications Part no. Product image/pin assignment Number of functional poles Key type Wiring specifications Note) Applicable cable Rating/Performance Material Cable O.D. Wire gauge (Stranded wire cross section) Weight (Mass) Core wire diameter (Including insulating material) Connection type Rated current Rated voltage Contact resistance Insulation resistance Withstand voltage Ambient temperature Protection class Allowable repeated insertion/withdrawal Allowable number of repeated connection between conductors of the same cross section Vibration resistance Material of knurl Contact (Surface treatment) Insulating material Note) The shaded parts show the specifications for the applicable cable. Adaptation for the connector may vary on account of the conductor construction of the electric wire. Dimensions PCA-770 PCA-77 PCA-776 M8 M M M8: poles.0 to.0 mm 0. to 0. mm /AWG6 to 0. to 0. mm /AWG to.0 to.6 mm Piercecon connection 60 V.0 kv 0 to 8 C 00 Brass Approx. g Plug. to 6.0 mm 0. to 0. mm /AWG6 to 0.7 to. mm A mω 00 MΩ IP67 (Only with screw tightened) M: poles QUICKON-ONE connection 0 V. kv to 80 C 00 Zinc for die casting CuZn (Au plating (Ni plating)) Polyamide (PA6.6) Approx. g Plug 0 0 to 00 Hz/98 m/s.0 to 8.0 mm 0. to 0.7 mm /AWG to 8. to. mm Approx. g Plug PCA-770 Fieldwireable connector (M8). Terminal no. Wire color SW ø.8 M8 PCA-77 Fieldwireable connector (M) M SPEEDCON PCA-776 Fieldwireable connector (M) ø.8 M SPEEDCON SW ø6. SW ø8. Plug connector pin assignment Plug connector pin assignment Plug connector pin assignment Brown Blue Black Terminal no. Terminal no. Wiring Wiring Wiring Wire color Brown White Blue Black Wire color Brown White Blue Black 7

24 Between Sensor/Switch and Input Device Cable with Connector Specifications Part no. M PCA-7769 M8 PCA-777 Product image Number of functional poles Key type Wiring specifications Rating/Performance Material Fixed cable length Cable O.D. Wire gauge (Stranded wire cross section) Rated current Rated voltage Contact resistance Insulation resistance Withstand voltage Ambient temperature Protection class Allowable repeated insertion/withdrawal Cable retaining force Vibration resistance Material of knurl Contact (Surface treatment) Insulating material Material of sheath Weight (Mass) Connector Cable Operating Fixed M: poles.7 ±0. mm 0. mm /AWG 0 V. kv 0 N/ sec. Approx. g m A mω 00 MΩ to 90 C to 80 C 0 to 80 C IP67 (Only with screw tightened) 00 0 to 00 Hz/98 m/s Zinc for die casting CuSn (Au plating (Ni plating)) Thermoplastic polyurethane (TPU) Polyurethane Black (PUR Black) M8: poles. ±0. mm 0. mm /AWG 60 V.0 kv 0 N/ sec. Approx. 80 g Dimensions PCA-7769 Cable with M connector ( poles) ø.8 M SPEEDCON ø.7 M SPEEDCON ø.8 Socket connector pin assignment Wiring Plug connector pin assignment PCA-777 Cable with M8 connector ( poles) ø0 M8 ø. M8 ø0 Socket connector pin assignment Wiring Plug connector pin assignment 8

25 Between Sensor/Switch and Input Device Y Connector Specifications Part no. PCA-778 Product image M M M Number of functional poles Key type Rated current Material Rating/Performance Rated voltage Contact resistance Insulation resistance Withstand voltage Ambient temperature Protection class Allowable repeated insertion/withdrawal Vibration resistance Material of knurl Contact (Surface treatment) Insulating material Weight (Mass) x M: poles + PE M: poles + PE A 60 V mω 00 MΩ.0 kv to 90 C IP67 (Only with screw tightened) 00 0 to 00 Hz/98 m/s Zinc for die casting CuZn (Au plating (Ni plating)) Thermoplastic polyurethane (TPU) Approx. 9 g Dimensions PCA-778 Y connector ( x M-M) 0. Socket connector pin assignment M SPEEDCON M SPEEDCON ø ø..8 ø ø.8.6 M SPEEDCON q w Socket connector pin assignment Wiring Plug connector pin assignment Connection image 9

26 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger. They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC), Japan Industrial Standards (JIS) ) and other safety regulations ). ) ISO : Pneumatic fluid power General rules relating to systems. ISO : Hydraulic fluid power General rules relating to systems. IEC 600-: Safety of machinery Electrical equipment of machines. (Part : General requirements) ISO 08-99: Manipulating industrial robots -Safety. JIS B 870: General rules for pneumatic equipment. JIS B 86: General rules for hydraulic equipment. JIS B 9960-: Safety of machinery Electrical equipment of machines. (Part : General requirements) JIS B 8-99: Manipulating industrial robots - Safety. etc. ) Labor Safety and Sanitation Law, etc. Caution: Operator error could result in injury or equipment damage. Warning: Operator error could result in serious injury or loss of life. Danger : In extreme conditions, there is a possibility of serious injury or loss of life. Warning. The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifications. Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalog information, with a view to giving due consideration to any possibility of equipment failure when configuring the equipment.. Only personnel with appropriate training should operate machinery and equipment. The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced.. Do not service or attempt to remove product and machinery/equipment until safety is confirmed.. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.. When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully.. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.. Contact SMC beforehand and take special consideration of safety measures if the product is to be used in any of the following conditions.. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight.. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifications described in the product catalog.. An application which could have negative effects on people, property, or animals requiring special safety analysis.. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. Back page

27 Safety Instructions Caution The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary. If anything is unclear, contact your nearest sales branch. Limited Warranty and Disclaimer/Compliance Requirements The product used is subject to the following Limited Warranty and Disclaimer and Compliance Requirements. Read and accept them before using the product. Limited Warranty and Disclaimer. The warranty period of the product is year in service or. years after the product is delivered. ) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch.. For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product.. Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the specified catalog for the particular products. ) Vacuum pads are excluded from this year warranty. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. Compliance Requirements When the product is exported, strictly follow the laws required by the Ministry of Economy, Trade and Industry (Foreign Exchange and Foreign Trade Control Law). Back page

28 Series EX600 Specific Product Precautions Be sure to read this before handling. Refer to back pages and for Safety Instructions, Handling Precautions for SMC Products (M-E0-) for // Port Solenoid Valves Precautions. Warning Design / Selection. Use this product within the specification range. Using beyond the specified specifications range can cause fire, malfunction, or damage to the system. Confirm the specifications when operating.. When using for an interlock circuit: Provide a multiple interlock system which is operated by another system (such as mechanical protection function). Perform an inspection to check that it is working properly. This may cause possible injury due to malfunction. Caution. Use the UL-certified products below for combined direct current power supply. () Circuit in which voltage and current are controlled in accordance with UL08 Circuit which makes the winding wire in the secondary side of the insulation transformer (which meets the following conditions) to be as the power supply Maximum voltage (with no load): 0 Vrms (. V at peak) or less Maximum current:. 8 A or less (including short-circuited). and in case of being controlled by circuit protection devices (fuse, etc) which meets the below rated voltages. Voltage with no load (V peak) Maximum rated current 0 to 0 (V).0 00 Exceeding 0 (V) up to 0 (V) Voltage figure at peak () Class power supply unit in accordance with UL0 or circuit (Class circuit) in accordance with UL8, that is powered by Class transformer with the maximum of 0 Vrms (. V at peak). Use this product within the specified voltage range. Using beyond the specified voltage range is likely to cause the units and connecting devices to be damaged or to malfunction.. The power supply for the unit should be 0 V as the standard for both power supply for output as well as power supply for control/input. Back page Power supply for output Power supply for control/input + V 0 V + V Power supply for output Power supply for control/input + V. Do not install a unit in a place where it can be used as a foothold. Applying any excessive load such as stepping on the unit by mistake or placing a foot on it, will cause it to break.. Keep the surrounding space free for maintenance. When designing a system, take into consideration the amount of free space needed for performing maintenance. 6. Do not remove the name plate. Improper maintenance or incorrect use of instruction manual can cause failure and malfunction. Also, there is a risk of losing conformity with safety standards. 7. Beware of inrush current when the power supply is turned on. Some connected loads can apply an initial charge current which will trigger the over current protection function, causing the unit to malfunction. 0 V V Caution Mounting. When handling and assembling units: Do not touch the sharp metal parts of the connector or plug. Do not apply excessive force to the unit. The connecting portions of the unit are firmly joined with seals. When joining units, take care not to get fingers caught between units. Injury can result.. Do not drop, bump, or apply excessive impact. Otherwise, the unit can become damaged, malfunction, or fail to function.. Observe the tightening torque range. Tightening outside of the allowable torque range will likely damage the product. IP67 protection class cannot be guaranteed if the screws are not tightened to the specified torque.. When lifting a large size manifold solenoid valve unit, take care to avoid causing stress to the valve connection joint. The connection parts of the unit may be damaged. Because the unit may be heavy, carrying and installation should be performed by more than one operator to avoid strain or injury.. When placing a manifold, mount it on a flat surface. Torsion in the whole manifold can lead to trouble such as air leakage or defective insulation. Caution Wiring. Confirm grounding to maintain the safety of the reduced wiring system and for anti-noise performance. Provide a specific grounding as close to the unit as possible to minimize the distance to grounding.. Avoid repeatedly bending or stretching the cable and applying a heavy object or force to it. Wiring applying repeated bending and tensile stress to the cable can break the circuit.. Avoid miswiring. If miswired, there is a danger of malfunction or damage to the reduced wiring system.. Do not wire while energizing the product. There is a danger of malfunction or damage to the reduced wiring system or input/output equipment.

29 Series EX600 Specific Product Precautions Be sure to read this before handling. Refer to back pages and for Safety Instructions, Handling Precautions for SMC Products (M-E0-) for // Port Solenoid Valves Precautions. Caution Wiring. Avoid wiring the power line and high pressure line in parallel. Noise or surge produced by signal line resulting from the power line or high pressure line could cause malfunction. Wiring of the reduced wiring system or input/output device and the power line or high pressure line should be separated from each other. 6. Confirm the wiring insulation. Defective insulation (contact with other circuits, improper insulation between terminals, etc.) may cause damage to the reduced wiring system or input/output device due to excessive voltage or current. 7. When a reduced wiring system is installed in machinery/equipment, provide adequate protection against noise by using noise filters, etc. Noise in signal lines may cause malfunction. 8. When connecting wires of input/output device or handheld terminal, prevent water, solvent or oil from entering inside from the connecter section. This can cause damage, equipment failure or malfunction. 9. Avoid wiring patterns in which excessive stress is applied to the connector. This may cause malfunction or damage to the unit due to contact failure. Operating Environment Warning. Do not use in an atmosphere containing an inflammable gas or explosive gas. Use in such an atmosphere is likely to cause a fire or explosion. This system is not explosion-proof. Caution. Select the proper type of protection according to the environment of operation. IP6/67 protection class is achieved when the following conditions are met. ) The units are connected properly with connector. ) Suitable mounting of each unit and manifold valve. ) Be sure to mount a seal cap on any unused connectors. If using in an environment that is exposed to water splashes, please take measures such as using a cover. Also, the Handheld Terminal confirms to IP0, so prevent foreign matter from entering inside, and water, solvent or oil from coming in direct contact with it. Caution Operating Environment. Provide adequate protection when operating in locations such as the following. Failure to do so may cause damage or malfunction. The effect of countermeasures should be checked in individual equipment and machine. ) Where noise is generated by static electricity, etc. ) Where there is a strong electric field ) Where there is a danger of exposure to radiation ) When in close proximity to power supply lines. Do not use in an environment where oil and chemicals are used. Operating in environments with coolants, cleaning solvents, various oils or chemicals may cause adverse effects (damage, malfunction) to the unit even in a short period of time.. Do not use in an environment where the product could be exposed to corrosive gas or liquid. This may damage the unit and cause it to malfunction.. Do not use in locations with sources of surge generation. Installation of the unit in an area around the equipment (electromagnetic lifters, high frequency induction furnaces, welding machine, motors etc.), which generates the large surge voltage could cause to deteriorate an internal circuitry element of the unit or result in damage. Implement countermeasures against the surge from the generating source, and avoid touching the lines with each other. 6. Use the product type that has an integratedsurge absorption element when directly driving a load which generates surge voltage by relay, solenoid valves or lamp. When a surge generating load is directly driven, the unit may be damaged. 7. The product is CE marked, but not immune to lightning strikes. Take measures against lightning strikes in your system. 8. Keep dust, wire scraps and other extraneous material from getting inside the product. This may cause malfunction or damage. 9. Mount the unit in such locations, where no vibration or shock is affected. This may cause malfunction or damage. 0. Do not use in places where there are cyclic temperature changes. In case that the cyclic temperature is beyond normal temperature changes, the internal unit is likely to be adversely effected.. Do not use in direct sunlight. Do not use in direct sunlight. It may cause malfunction or damage.. Use this product within the specified ambient temperature range. This may cause malfunction.. Do not use in places where there is radiated heat around it. Such a place is likely to cause malfunction. Back page

30 Series EX600 Specific Product Precautions Be sure to read this before handling. Refer to back pages and for Safety Instructions, Handling Precautions for SMC Products (M-E0-) for // Port Solenoid Valves Precautions. Warning Adjustment / Operation. Do not perform operation or setting with wet hands. There is a risk of electrical shock. <Handheld Terminal>. Do not apply pressure to the LCD display. There is a possibility of the crack of LCD display and injuring.. The forced input/output function is used to change the signal status forcibly. When operating this function, be sure to check the safety of the surroundings and installation. Otherwise, injury or equipment damage could result.. Incorrect setting of parameters can cause malfunction. Be sure to check the settings before use. This may cause injury or equipment damage. Caution. Use a watchmaker s screwdriver with thin blade for the setting of each switch of the SI unit. When setting the switch, do not touch other unrelated parts. This may cause parts damage or malfunction due to a short circuit.. Provide adequate setting for the operating conditions. Failure to do so could result in malfunction. Refer to the instruction manual for setting of the switches.. For the details of programming and address setting, refer to the manual from the PLC manufacturer. The content of programming related to protocol is designed by the manufacturer of the PLC used. <Handheld Terminal>. Do not press the setting buttons with a sharp pointed object. This may cause damage or malfunction.. Do not apply excessive load and impact to the setting buttons. This may cause damage, equipment failure or malfunction. When the order does not include the SI unit, the valve plate to connect the manifold and SI unit is not mounted. Use attached valve fixing screws and mount the valve plate. (Tightening torque: 0.6 to 0.7 N m) Screw tightened parts Series SV: places Series S0700: places Series VQC000: places Series VQC000: places Series VQC000: places Warning Maintenance. Do not disassemble, modify (including circuit board replacement) or repair this product. Such actions are likely to cause injuries or breakage.. When an inspection is performed, Turn off the power supply. Stop the air supply, exhaust the residual pressure in piping and verify that the air is released before performing maintenance work. Unexpected malfunction of system components and injury can result. Caution. When handling and replacing the unit: Do not touch the sharp metal parts of the connector or plug. Do not apply excessive force to the unit. The connecting portions of the unit are firmly joined with seals. When joining units, take care not to get fingers caught between units. Injury can result.. Perform periodic inspection. Unexpected malfunction in the system composition devices is likely to occur due to malfunction of machinery or equipment.. After maintenance, make sure to perform an appropriate functionality inspection. In cases of abnormality such as faulty operation, stop operation. Unexpected malfunction in the system composition devices is likely to occur.. Do not use benzene and thinner for cleaning units. Damage to the surface or erasure of the display can result. Wipe off any stains with a soft cloth. If the stain is persistent, wipe off with a cloth soaked in a dilute solution of neutral detergent and wrung out tightly, and then finish with a dry cloth. Caution Other. Refer to the catalog of each series for Common Precautions and Specific Product Precautions on manifold solenoid valves. Valve holding screw Valve plate Trademark DeviceNet TM is a trademark of ODVA. Product names described in this catalog may be used as trademarks by each manufacturer. Back page

31 SMC'S GLOBAL MANUFACTURING, DISTRIBUTION AND SERVICE NETWORK EUROPE AUSTRIA SMC Pneumatik GmbH (Austria) BELGIUM SMC Pneumatics N.V./S.A. BULGARIA SMC Industrial Automation Bulgaria Eood CROATIA SMC Industrijska Automatika d.o.o. CZECH REPUBLIC SMC Industrial Automation CZ s.r.o. DENMARK SMC Pneumatik A/S ESTONIA SMC Pneumatics Estonia OÜ FINLAND SMC Pneumatics Finland Oy FRANCE SMC Pneumatique SA GERMANY SMC Pneumatik GmbH GREECE SMC Hellas E.P.E. HUNGARY SMC Hungary Ipari Automatizálási Kft. IRELAND SMC Pneumatics (Ireland) Ltd. ITALY SMC Italia S.p.A. LATVIA SMC Pnuematics Latvia SIA LITHUANIA UAB SMC Pneumatics NETHERLANDS SMC Pneumatics B.V. NORWAY SMC Pneumatics Norway AS POLAND SMC Industrial Automation Polska Sp.z.o.o. ROMANIA SMC Romania S.r.l. RUSSIA SMC Pneumatik LLC SLOVAKIA SMC Priemyselná Automatizácia Spol s.r.o. SLOVENIA SMC Industrijska Avtomatika d.o.o. SPAIN/PORTUGAL SMC España S.A. SWEDEN SMC Pneumatics Sweden AB SWITZERLAND SMC Pneumatik AG U.K. SMC Pneumatics (U.K.) Ltd. ASIA CHINA SMC (China) Co., Ltd. HONG KONG SMC Pneumatics (Hong Kong) Ltd. INDIA SMC Pneumatics (India) Pvt. Ltd. MALAYSIA SMC Pneumatics (S.E.A.) Sdn. Bhd. PHILIPPINES Shoketsu SMC Corporation SINGAPORE SMC Pneumatics (S.E.A.) Pte. Ltd. SOUTH KOREA SMC Pneumatics Korea Co., Ltd. TAIWAN SMC Pneumatics (Taiwan) Co., Ltd. THAILAND SMC (Thailand) Ltd. NORTH AMERICA CANADA SMC Pneumatics (Canada) Ltd. MEXICO SMC Corporation (Mexico), S.A. de C.V. U.S.A. SMC Corporation of America SOUTH AMERICA ARGENTINA SMC Argentina S.A. BOLIVIA SMC Pneumatics Bolivia S.r.l. BRAZIL SMC Pneumáticos do Brasil Ltda CHILE SMC Pneumatics (Chile) S.A. VENEZUELA SMC Neumatica Venezuela S.A. OCEANIA AUSTRALIA SMC Pneumatics (Australia) Pty. Ltd. NEW ZEALAND SMC Pneumatics (N.Z.) Ltd. Safety Instructions Be sure to read Handling Precautions for SMC Products (M-E0-) before using. Akihabara UDX F, --, Sotokanda, Chiyoda-ku, Tokyo 0-00, JAPAN Phone: Fax: URL SMC Corporation All Rights Reserved Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. D-DN st printing MW printing MW 600DN Printed in Japan. This catalog is printed on recycled paper with concern for the global environment.