Installing Avaya P550 /P580/P880/P882

Transcription

1 Installing Avaya P550 /P580/P880/P882 CHAPTER 1 Gigabit Ethernet Modules Overview This document describes the following processes: Gigabit-Speed Modules Compliance Information Software Requirements Power Requirements Installing the Modules Installing GBIC Connectors Installing the Cables Gigabit-Speed Modules 50 Series Modules 80 Series Modules This document describes installation and configuration of the following media modules: 2-Port, Full-Duplex 1000BASE-X module: 850 nm (SX) and 1310 nm (LX and SLX) - (Layer 2 and Layer 3) 4-Port, Full-Duplex 1000BASE-X module: 850 nm (SX) and 1310 nm (LX and SLX) - (Layer 2) 4-Port, Gigabit Interface Card (GBIC) based module: 850 nm (SX), 1310 nm (LX and SLX) and 1550 nm (ELX) (Layer 2 and Layer 3) 8-Port, Gigabit Interface Card (GBIC) based module: 850 nm (SX), 1310 nm (LX and SLX) and 1550 nm (ELX) (Layer 2 and Layer 3) October

2 Compliance Information FCC Compliance Please read the following compliance information prior to installing your Avaya Gigabit Ethernet Module. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet apparell numérique de la classe A respecte toutes les exigences du Régelment sur le matériel brouilleur du Canada. WARNING This is a class A product. In a domestic environment, this product may cause radio interference, in which case you may be required to take adequate measures. Laser Safety Information * Note: This notice applies to devices that contain optical transceiver media modules installed. The transceivers used in this product are Class 1 Laser Products. This product complies with 21 CFR Chapter 1, Subchapter J. Any use other than that specified herein may result in hazardous laser radiation exposure. Unterminated optical receptacles may emit laser radiation. Do not view with optical instruments. This product complies with IEC , Safety of Laser Products, Class 1 Laser Product. 2 October

3 Software Requirements Power Requirements The Avaya P550R/P580/P880/P Series modules require software of Version 5.0 or higher. In the P550 chassis, each power supply powers approximately four media modules. In the P880 chassis, each power supply powers approximately nine media modules. It takes two power supplies to power a full chassis. Using three power supplies ensures that the system has redundant power capabilities. Use Tables 1 and 2 for the precise power values: Table 1. Power Values for System Devices - 50-Series Modules Device 2-Port Gigabit Module 4-Port Gigabit Module Power Used 35 W 55 W Table 2. Power Values for System Devices - 80-Series Modules Device 4-Port Gigabit Module 8-Port Gigabit Module Power Used 45 W 75 W Select Power System from the System > Configuration > group on the web agent window to determine how much power is currently available in your switch October

4 Installing the Modules * Note: All Avaya media modules are hot swappable. You do not need to shut down the switch when adding modules. To install modules in the chassis: 1. Carefully remove the module from its box, leaving the module in its anti-static wrapping. 2. Take appropriate antistatic precautions and carefully remove the module from the antistatic wrap (refer to Chapter 1, Installation in the Avaya P550/P580/P880/P882 Multiservice Switch Installation Guide for detailed information on proper antistatic precautions). 3. Open the Ejector Tabs until the stops make contact with the face plate (Figure 1). Figure 1. Installing the Module 4. Insert the module into the chassis (Figure 1). 5. Press on the center of the module as you push it into the chassis. The ejectors snap into place. 6. Push the ejectors into the closed position to complete seating the module (Figure 2). 4 October

5 Figure 2. Closing the Ejector Tabs 7. Tighten the captive screws. As the module powers up, the LEDs should function as described in the module descriptions provided in the Avaya P550/P580/P880/P882 User Guide. In general, the following is observed on a properlyfunctioning module (Table 3 ): Table 3. Power-up LED Function Module LED Normal Behavior All Modules Module Status Solid green, indicating normal operation. Gigabit Modules TX and RX Port HD/FD Solid green, flashing yellow intermittently to indicate traffic Solid green, indicating link integrity. Solid green, indicating full-duplex operation October

6 Installing GBIC Connectors GBIC connectors are only applicable to 80-Series modules. They come in the following types: SX (550m-capable) LX (10km-capable) SLX (25km-capable) ELX (70-100km-capable) Refer to Table 4 and Table for distances and wave lengths. * Note: All Avaya GBIC connectors are hot swappable. You do not need to shut down the switch when adding modules. To install a GBIC connector into a module: 1. Carefully remove the GBIC connector from its packaging, leaving the module in its anti-static wrapping. 2. Take appropriate antistatic precautions and carefully remove it from the antistatic wrap. (Refer to the Avaya P550/P580/P880/ P882 Multiservice Switch User Guide for more information on proper antistatic precautions). 3. Carefully slide the GBIC connector into the module until the side connectors click into place (Figure 3). 6 October

7 Figure 3. Installing a GBIC Connector Installing the Cables Install the appropriate cables for your network configuration. The Avaya P550/P580/P880/P882 Multiservice Switch supports the following cable type: Fiber cables with SC-type connectors Optical Channel Requirements The optical fiber types that can be used with the Gigabit Ethernet Modules are standard single-mode and multimode optical fibers that conform to the requirements of the following standards. Single-mode Optical Fiber: IEC B1.1 (dispersion unshifted single-mode) or IEC B1.3 (low water peak single-mode) ITU-T Recommendation G.652 Dispersion Unshifted Fiber October

8 TIA/EIA 492CAAA Dispersion-Unshifted Single-Mode Optical Fibers or TIA/EIA 492CAAB Dispersion-Unshifted Single-Mode Optical Fibers with Low Water Peak Multimode Optical Fiber: TIA/EIA 492AAAA 62.5/125 micron Multimode Optical Fiber TIA/EIA 492AAAB 50/125 micron Multimode Optical Fiber TIA/EIA 492AAAC 50/125 micron Laser Optimized Multimode Optical Fiber IEC type A1a.2 (in preparation) Examples of optical fibers that meet these requirements include (but are not limited to): Single-mode Optical Fiber Corning SMF-28 Fiber Corning SMF-28e Fiber OFS Fitel Single-Mode Fiber OFS Fitel AllWave Fiber Avaya Systimax Single-Mode Fiber Cable Multimode Optical Fiber Corning Infinicor Corning Infinicor SX OFS GigaSPEED OFS LazrSPEED Draka Comteq Max Cap October

9 Refer to Table 4 and Table 5 for supported link distances for the Gigabit Ethernet Modules. Table 4. Supported Link Distances Model Number M SX M SX M5502R- 1000SX M LX M LX M5502R- 1000LX M SLX M SLX M5502R- 1000SLX Wavelength Fiber Type Link Distance (m) 850 nm 50 µm MMF 400 MHz*km 500 MHz*km 62.5 µm MMF 160 MHz*km 200 MHz*km 2 to to nm 50 µm MMF 400 MHz*km 500 MHz*km 62.5 µm MMF 160 MHz*km 200 MHz*km 9/10 µm SMF 2 to nm 62.5 µm MMF 160 MHz*km 200 MHz*km 9/10 µm SMF 2 to Table 5. Supported Link Distances - GBICs GBIC Part Number M SX Wavelength Fiber Type Link Distance (m) 850 nm GBIC 50 µm MMF 400 MHz*km 500 MHz*km 62.5 µm MMF 160 MHz*km 200 MHz*km 2 to to October

10 GBIC Part Number M LX M SLX M ELX Wavelength Fiber Type Link Distance (m) 1310 nm GBIC 62.5 µm MMF 160 MHz*km 200 MHz*km 9/10 µm SMF 2 to nm GBIC 9/10 µm SMF 2 to nm GBIC 9/10 µm SMF Up to 70,000 to 100,000 Table 6 lists the optical fiber specifications for the Gigabit Ethernet Modules. Table 6. Optical Fiber Specifications Description 62.5 µm MMF 50 µm MMF Type B1.1, B1.3 SMF Unit Nominal fiber specification wavelength nm Fiber cable attenuation (max) Modal bandwidth (min) Zero dispersion wavelength (λ 0 ) Dispersion slope (max) (S0) a or 0.5 b See Footnote c db/km 160 d or 200 d 400 d or 500 d or 2000 e N/A MHz km 1320 λ λ for 1320 λ and 0.001( λ 0 ) for 1348 λ for 1300 λ and 0.001( λ 0 ) for 1295 λ λ nm ps / nm 2 km a. For the single-mode case, the 0.4 db/km attenuation for optical fiber cables is defined in ITU-T G October

11 b. For the single-mode case, the 0.5 db/km attenuation is provided for Outside Plant cable as defined in TIA 568B.3. Using 0.5 db/km may not support operation at 10 km. c. Attenuation for 1550 nm links is based on the fiber channel and is specified in IEEE 802.3ae Table d. Overfilled launch bandwidth per IEC or TIA/EIA e. Effective modal bandwidth for fiber meeting TIA /EIA-492AAAC when used with sources meeting the wavelength (range) and encircled flux specifications of IEEE 802.3ae Table For More Information Refer to the Avaya P550/P580/P880/P882 Multiservice Switch User Guide for more information concerning module configuration options October

12 12 October