AMENDED FINAL REPORT FOR:

Transcription

1 731 Enterprise Drive Lexington, KY Telephone: Facsimile: AMENDED FINAL REPORT FOR: CUSTOMER NAME: PRODUCT NAME: Leviton Manufacturing Co. 417 Stone Drive St. Charles, IL Fiber 100G 5 Matings OM3 Link System Tested To: IEEE 802.3ba-2010 IEEE Standard for Information technology-- Local and metropolitan area networks-- Specific requirements-- Part 3: CSMA/CD Access Method and Physical Layer Specifications Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation, June 2010 Date: September 8, 2011 Project: G Report: LEX Responsible Engineer: Date: 9/8/2011 Paul Alt, Senior Project Engineer Approved By: Date: 9/8/2011 Richard Proctor, Operations Manager This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services NA, Inc.

2 TABLE OF CONTENTS Page Declaration of Compliance...3 Sample Condition and Receive Date IEEE 802.3ba-2010, IEEE Standard for Information technology-- Local and metropolitan area networks-- Specific requirements Part 3: CSMA/CD Access Method and Physical Layer Specifications Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation...4 References:...12 LIST OF TABLES Page Table 1: History of Revision...2 Table 2: IEEE 802.3ba Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation - Table Fiber Optic Cabling Channel Characteristics at 850 nm...4 Table 3: 24 Fiber 100G 5 Matings OM3 Link System Part Numbers and Quantities...6 Table 4: Insertion Loss Forward Reading at 850 nm...8 Table 5: Insertion Loss Reverse Reading at 850 nm...9 Table 6: Insertion Loss Average Reading at 850 nm...10 LIST OF FIGURES Page Figure 1: Cable Link Channel Testing Configuration...6 Figure 2: Manufacturer s 24 Fiber 100G 5 Matings OM3 Link System Diagram...6 Figure 3: 24 Fiber 100G 5 Matings OM3 Link System Test Setup...11 Table 1: History of Revision Revision Date Section # Description of Revision Original August 30, 2011 All Original Document Issued 01 September 8, 2011 All Corrected reference to IEEE standard Report: LEX Page 2 of 12 Revision 01

3 Declaration of Compliance The 24 Fiber 100G 5 Matings OM3 Link System was evaluated and found to be compliant with all applicable criteria of channel insertion loss testing for IEEE 802.3ba-2010, IEEE Standard for Information technology-- Local and metropolitan area networks-- Specific requirements-- Part 3: CSMA/CD Access Method and Physical Layer Specifications Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation, June Sample Condition and Receive Date Leviton Manufacturing Co. selected and provided the test samples for evaluation to the criteria of IEEE 802.3ba-2010, IEEE Standard for Information technology-- Local and metropolitan area networks-- Specific requirements-- Part 3: CSMA/CD Access Method and Physical Layer Specifications Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation, June The equipment tested was the 24 Fiber 100G 5 Matings OM3 Link System; the new and unused samples were tested by Leviton and witnessed by Intertek on 8/15/2011. Report: LEX Page 3 of 12 Revision 01

4 1 IEEE 802.3ba-2010, IEEE Standard for Information technology-- Local and metropolitan area networks-- Specific requirements 1.1 Part 3: CSMA/CD Access Method and Physical Layer Specifications Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation Channel Insertion Loss Testing Conformance Criteria The cable link system channel shall not exhibit a change greater than the value stated in Table 2 below for the Multi-Mode test condition and the corresponding product type evaluation. a. For this evaluation, the criteria is for an Ethernet 40GBASE-SR4 and 100GBASE- SX system measured at 850 nm laser-optimized 50/125 µm TIA 492AAAC (OM3) having a maximum channel value of 1.9 db as indicated by the matching values in Table 2. Table 2: IEEE 802.3ba Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation - Table Fiber Optic Cabling Channel Characteristics at 850 nm. Description Type OM3 OM4 Unit Operating Distance Max m Cabling Skew a Max 79 ns Cabling Skew Variation Max 2.5 ns Channel Insertion Loss Min 0 db Channel Insertion Loss b Max 1.9 c 1.5 d db a An additional 300 ps of Skew Variation could be caused by wavelength changes, which are attributable to the transmitter, not the channel. b These channel insertion loss values include cable, connectors and splices. c 1.5 db allocated for connection and splice loss. d 1 db allocated for connection and splice loss. Report: LEX Page 4 of 12 Revision 01

5 Sample Size One 24 Fiber 100G 5 Matings OM3 Link System was tested for compliance to IEEE 802.3ba-2010, IEEE Standard for Information technology-- Local and metropolitan area networks-- Specific requirements-- Part 3: CSMA/CD Access Method and Physical Layer Specifications Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation Test Method 1. The test methodology used was the Leviton Manufacturing Co. internal qualification document FBFMM127, Revision A, dated 2/23/2011 titled Insertion Loss and Continuity Testing Instructions on the 24 Channel MM OptoTest Power Meter. 2. These instructions were reviewed prior to the start of testing and found to be sufficient to the required channel loss testing as detailed in IEEE 802.3ba-2010, IEEE Standard for Information technology-- Local and metropolitan area networks- - Specific requirements-- Part 3: CSMA/CD Access Method and Physical Layer Specifications Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation, June Prior to the beginning of testing, the Intertek witness representative reviewed the training records of all employees involved to determine that the manufacturer had kept detailed training records of testing qualifications. 4. The testing was conducted per the FBFMM127, Revision A, dated 2/23/2011 titled Insertion Loss and Continuity Testing Instructions on the 24 Channel MM OptoTest Power Meter and the results were recorded. 5. The data was reviewed by the Intertek witness representative and found to be compliant with all applicable criteria. 6. The loss for each channel, as well as the measurement direction the loss was calculated in, was reported individually in the Test Results section of this report Test Configurations and Conditions The test was conducted at lab ambient atmospheric conditions; 23 2 C, ~75% RH. Optical measurements were taken at 850 nm. The test measurement configuration is demonstrated in Figure 1. The customer s equipment configuration is demonstrated in Figure 2 and the individual part identification numbers are listed in Table 3. Report: LEX Page 5 of 12 Revision 01

6 Figure 1: Cable Link Channel Testing Configuration Figure 2: Manufacturer s 24 Fiber 100G 5 Matings OM3 Link System Diagram Table 3: 24 Fiber 100G 5 Matings OM3 Link System Part Numbers and Quantities Item Leviton Part Number Description Qty 1 FH-EH024HG336BC Harness, 24 fiber-mtp to FC/APC, 3FT, OM L4TE-M05 Array cord, 24 fiber, MTP-MTP, OM3, Method B, 5mtr 2 3 5L4TE-M01 Array cord, 24 fiber, MTP-MTP, OM3, Method B, 1mtr 2 4 FT-EB024JJ100M36C36CN-NNBS Trunk, 24 fiber, OM3, MTP-MTP, Plenum, Method B, 100M 1 5 5F100-MB MTP Adapter plate 5 Report: LEX Page 6 of 12 Revision 01

7 Test Equipment Channel Insertion Loss Testing Model Last Cal Next Cal Equipment Type Manufacturer Number Date Date Fiber Optic Cleaning Reels CLETOP Type A NA NA 850 nm Light Source OptoTest OP930-MM- SW24-85/13 NA NA Power Meter with S-RHIS Detector Head OptoTest OP710-R-S 11/30/ /30/2011 Optical Fiber Multi Mode 50/125 µm Jacketed Cable (Launch Lead) Leviton NA NA NA Mandrel Wrap Leviton NA NA NA Computer with Measurement Software Leviton NA NA NA NA: Not Applicable Summary of Test Results Conformance/Nonconformance Criteria Ethernet 40GBASE-SR4 and 100GBASE-SX system measured at 850 nm laser-optimized 50/125 µm TIA 492AAAC (OM3) having a maximum channel value of 1.9 db Conforms? C/NC C Actual Sample Size and Test Method Deviations One 24 Fiber 100G 5 Matings OM3 Link System was tested for compliance to this section. There were no deviations from, additions to, or exclusions from, the documented test method here. Failure History There was no history of failure for the testing in this section. Disposition of Nonconformance There was no failure for the testing in this section. Report: LEX Page 7 of 12 Revision 01

8 Test Data OM3 Channel Table 4: Insertion Loss Forward Reading at 850 nm Test Witnessed By: Test Date Paul Alt 8/15/2011 OM3 Configuration Directional Reading Max Value (db) Loss Criteria Complies? Y/N 1 Forward db Y 2 Forward db Y 3 Forward db Y 4 Forward db Y 5 Forward db Y 6 Forward db Y 7 Forward db Y 8 Forward db Y 9 Forward db Y 10 Forward db Y 11 Forward db Y Fiber 100G 5 Matings OM3 Forward db Y 13 Link System Forward db Y 14 Forward db Y 15 Forward db Y 16 Forward db Y 17 Forward db Y 18 Forward db Y 19 Forward db Y 20 Forward db Y 21 Forward db Y 22 Forward db Y 23 Forward db Y 24 Forward db Y Report: LEX Page 8 of 12 Revision 01

9 OM3 Channel Table 5: Insertion Loss Reverse Reading at 850 nm Test Witnessed By: Test Date Paul Alt 8/15/2011 OM3 Configuration Directional Reading Max Value (db) Loss Criteria Complies? Y/N 1 Reverse db Y 2 Reverse db Y 3 Reverse db Y 4 Reverse db Y 5 Reverse db Y 6 Reverse db Y 7 Reverse db Y 8 Reverse db Y 9 Reverse db Y 10 Reverse db Y 11 Reverse db Y Fiber 100G 5 Matings OM3 Reverse db Y 13 Link System Reverse db Y 14 Reverse db Y 15 Reverse db Y 16 Reverse db Y 17 Reverse db Y 18 Reverse db Y 19 Reverse db Y 20 Reverse db Y 21 Reverse db Y 22 Reverse db Y 23 Reverse db Y 24 Reverse db Y Report: LEX Page 9 of 12 Revision 01

10 OM3 Channel Table 6: Insertion Loss Average Reading at 850 nm Test Witnessed By: Test Date Paul Alt 8/15/2011 OM3 Configuration Directional Reading Max Value (db) Loss Criteria Complies? Y/N 1 Average db Y 2 Average db Y 3 Average db Y 4 Average db Y 5 Average db Y 6 Average db Y 7 Average db Y 8 Average db Y 9 Average db Y 10 Average db Y 11 Average db Y Fiber 100G 5 Matings OM3 Average db Y 13 Link System Average db Y 14 Average db Y 15 Average db Y 16 Average db Y 17 Average db Y 18 Average db Y 19 Average db Y 20 Average db Y 21 Average db Y 22 Average db Y 23 Average db Y 24 Average db Y Report: LEX Page 10 of 12 Revision 01

11 Photograph: Figure 3: 24 Fiber 100G 5 Matings OM3 Link System Test Setup Report: LEX Page 11 of 12 Revision 01

12 References: External Reference Documents ANSI Z136.2 ANS For Safe Use Of Optical Fiber Communication Systems Utilizing Laser Diode And LED Sources ANSI/TIA-568-C.0 General Telecommunications Cabling for Customer Premises ANSI/TIA-568-C.1 Commercial Building Telecommunications Cabling Standard ANSI/TIA-568-C.2 Balanced Twisted-Pair Telecommunications Cabling and Components Standard ANSI/TIA Fiber Optic Connector Intermateability Standard, Type SC and SC- APC ANSI/TIA Fiber optic Intermateability Standard, Type MPO IEEE C2-2007, National Electrical Safety Code (NESC ) IEEE , Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications IEEE 802.3ba-2010, IEEE Standard for Information technology-- Local and metropolitan area networks-- Specific requirements-- Part 3: CSMA/CD Access Method and Physical Layer Specifications Amendment 4: Media Access Control Parameters, Physical Layers, and Management Parameters for 40 Gb/s and 100 Gb/s Operation IEC , Industrial Communication Networks - Installation of Communication Networks in Industrial Premises NFPA 70, National Electrical Code TIA-492AAAA, Detail Specification For 62.5-μm Core Diameter/125-μm Cladding Diameter Class IA Graded-Index Multimode Optical Fibers TIA-492AAAB, Detail Specification For 50-μm Core Diameter/125-μm Cladding Diameter Class IA Graded-Index Multimode Optical Fibers TIA-492AAAC, Detail Specification For 850-nm Laser-Optimized, 50-μm Core Diameter/125-μm Cladding Diameter Class IA Graded-Index Multimode Optical Fibers TIA-492AAAD, Detail Specification For 850-nm Laser-Optimized, 50 µm Core Diameter/125 µm Cladding Diameter Class IA Graded-Index Multimode Optical Fibers of OM4 Performance TIA-492CAAA, Detail Specification For Class IVA Dispersion-Unshifted Single-Mode Optical Fibers TIA-492CAAB, Detail Specification For Class IVA Dispersion-Unshifted Single-Mode Optical Fibers With Low Water Peak TIA TSB-31-C, Telephone Terminal Equipment Rationale and Measurement Guidelines for US Network Protection 51 Report: LEX Page 12 of 12 Revision 01