Natural cooling, When output exceed 80% LOAD, a 18 CFM(min) DC fan is required

Transcription

1 SPU-250P-xx Series Features: Universal AC input with active power factor correction, P.F.>0.95 High efficiency and high reliability Built-in filter, low ripple noise Output voltage remote sense -20 ~70 Operating temperature U, cu, TUV, CB, CE standard 3 years warranty Specification: Voltage IPUT OUTPUT Frequency Current Inrush Current eakage Current 88V ~ 264VAC universal full range or 125V ~ 375VDC Hz AC input, full load condition <35A@115V, <70A@230V AC input. Cold start at 25 ambient <1.5mA@264V AC input Power Factor PF 0.95 MODE o. SPU-250P-05 SPU-250P-7.5 SPU-250P-12 SPU-250P-15 SPU-250P-24 SPU-250P-48 Voltage 5V 7.5V 12V 15V 24V 48V Min oad 0A 0A 0A 0A 0A 0A Max oad 42A 30A 20.8A 16.7A 10.5A 5.3A Voltage adjustment 4.5V~5.5V 6.7V~8.3V 10.8V~13.2V 13.5V~16.5V 21.6V~26.4V 43.2V~52.8V Output Tolerance ± 2% ±2% ± 1% ± 1% ± 1% ± 1% Ripple oise MAX. 70mV mv 120mV 150mV 200mV 250mV Efficiency (TYP.) 83% 84% 86% 86% 87% 89% Output MAX. 210W 225W 250W 250.5W 252W 254W Over Voltage 5.8~7.0V 8.6~10.5V 13.8~16.8V 17.3~21.0V 27.6~33.6V 55.2~67.2V Shutdown and latch off, recover after re-start up. PROTECTIO When power supply over 105%~ 150 max load or short circuit acted, power supply will be shutdown and Over oad Short Circuit recover automatically after the fault is removed. Rise time <20mS EEC. CHAR. Hold up time >20mS@230V, full load condition Setup time <2.0S@ 2V AC Remote sensing (RS+, RS-). Temperature Operating: -20 ~ +70 ; De-rating: 45 ~ 70 : 2.5%/ ; Storage: - ~ +85 EVIROMET Humidity Operating: 20% ~ 90% RH (non condensing) ; Storage: 10% ~ 95% RH (non condensing) Withstand voltage -O/P:3KVAC, -:1.5KVAC, O/P-:0.5KVAC, 1minute SAFETY Isolation resistance -O/P, -, O/P- M /500VDC at 25 / 70% RH Safety standard U nd,csa C22.2 o nd,tuv E 950-1:2006+A11+A1+A12,IEC 950-1:2005+A1, standard. E CASS B FCC CFR 47 PART 15 CASS B CS CASS B. EMC Compliance to E-3-2 CASS D, E-3-3 EMS E E -4-2,3,4,5,6,8,11 Cooling atural cooling, When output exceed % OAD, a 18 CFM(min) DC fan is required OTHERS M.T.B.F. K hours Dimension 198 x 97 x 38 (*W*H) Packing.W.: Kg / 1pc; 18 pcs / 1.38 CUFT / 1 CT OTE 250W, Single Output Active P.F.C Function All measurements which not mentioned are based on 230VAC input, output Max at ambient 25 / 70%RH Output tolerance included set up voltage, line regulation and load regulation. Ripple noise are measured at 254VAC input with condition and 20MHz of bandwidth by using a twisted pair-wire terminated with a 0.1uF a 47uF parallel capacitor. The operating temperature shall follow the de-rating curve in spec 198 x 97 x 38 mm 7.8 x 3.82 x 1.50 inch The output load may be requested for decreasing as de-rating curve in spec when low input voltage is under VAC. The power supply is considered a component of end-equipment. The end-equipment must be re-confirmed whether comply with EMC directives. Copy Right Sunpower Technology Corp. 2009, All Rights Reserved. SPU-250P-xx Rev 0.2 RS MAY

2 SPU-250P-xx Series Block Diagram PS3 V+ V- FWM S- S+ De-rating Curve Output De-rating Vs Input Voltage Ta= (HORIZOTA) ~ Dimension: AMBIET TEMRATURE( ) IPUT VOTAGE (VAC) Hz (Unit: mm) OTES: TERMIA BOCK: =3P, P=9.5mm MODE o SPU-250P-xx TERMIA BOCK: O/P:6P, P=9.5mm MODE o SPU-250P-xx +V +V +V -V -V -V Copy Right Sunpower Technology Corp. 2009, All Rights Reserved. SPU-250P-xx Rev 0.2 RS MAY

3 SPU-250P-IDx Series 16F.-1, o.150, Jian 1st Rd., Zhonghe Dist., ew Taipei City 235, Taiwan (R.O.C.) Features: * Universal AC input with active power factor correction, P.F.>0.95 * outputs are isolated * High efficiency and high reliability * Built-in filter, low ripple noise * Output voltage remote sense * Over temperature protection (Optional) * -20 ~70 Operating temperature * U, cu, TUV, CB, CE standard * 3 years warranty Specification: Voltage IPUT OUTPUT 88V ~ 264VAC universal full range or 125V ~ 375VDC. Frequency Hz Current <3.5A@VAC input, full load condition Inrush Current <35A@115V, <70A@230V AC input. Cold start at 25 ambient eakage Current <1.5mA@264V AC input Power Factor PF > 0.95 MODE o. SPU-250P-ID5 SPU-250P-ID6 SPU-250 P-ID7 Voltage 12V 5V 24V 5V 48V 5V Min oad 1A 0A 0.5A 0A 0.3A 0A Max oad 20A 4A 10A 4A 5A 4A Output Tolerance ±1% ±5% ±1% ±5% ±1% ±5% Ripple oise MAX. 120mV 70mV 200mV 70mV 2mV 70mV Efficiency (TYP.) 83% 85% 86% Output MAX. 250W 250W 250W Over Voltage 13.8 ~ 16.8V ~ 33.6V ~ 67.2V --- Shutdown and latch off, recover after re-start up. PROTECTIO When power supply over 105%~ 150 max load or short circuit acted, power supply will be shutdown and Over oad Short Circuit recover automatically after the fault is removed. Over Temperature Optional, Over 95 ± 5 Shutdown, recovers automatically after fault condition has been removed. Rise time <20mS EEC. CHAR. Hold up time >20mS@230V, full load condition Setup time <2 Sec@ ~ 2V AC Remote sensing (RS+, RS-). Temperature Operating: -20 ~ +70 ; De-rating: 45 ~ 70 : 2.5%/ ; Storage: - ~ +85 EVIROMET Humidity Operating: 20% ~ 90% RH (non condensing) ; Storage: 10% ~ 95% RH (non condensing) Withstand voltage -O/P:3KVAC, -:1.5KVAC, O/P-:0.5KVAC, 1minute SAFETY Isolation resistance -O/P, -, O/P- >MΩ/500VDC at 25 / 70% RH Safety standard U nd,csa C22.2 o nd,tuv E 950-1:2006+A11+A1+A12,IEC 950-1:2005+A1, standard. E CASS B FCC CFR 47 PART 15 CASS B CS CASS B. EMC Compliance to E-3-2 CASS D, E-3-3 EMS E 55024:E -4-2,3,4,5,6,8,11 Cooling atural cooling, when output exceed % OAD, a 18 CFM(min) DC fan is required OTHERS M.T.B.F. K hours Dimension 198*97*38 mm (*W*H) Packing.W.: Kg / 1pc; 18 pcs / 1.38 CUFT / 1 CT OTE 250W, Dual Output Active P.F.C Function All measurements which not mentioned are based on 230VAC input, output Max at ambient 25 / 70%RH Output tolerance included set up voltage, line regulation and load regulation. The regulation is measured between 20%-% max load of each output, Total output t must under output Max. 198 x 97 x 38 mm 7.8 x 3.82 x 1.50 inch Ripple noise are measured at ~254VAC input with 10~50 condition and 20MHz of bandwidth by using a 10 ~15 twisted pair-wire terminated with a 0.1uF a 47uF parallel capacitor. The operating temperature shall follow the de-rating curve in spec The output load may be requested for decreasing as de-rating curve in spec when low input voltage is under VAC The power supply is considered a component of end-equipment. The end-equipment must be re-confirmed whether comply with EMC directives. Copy Right Sunpower Technology Corp. 2009, All Rights Reserved. SPU-250P-IDx Rev 0.2 RS MAY

4 SPU-250P-IDx Series 16F.-1, o.150, Jian 1st Rd., Zhonghe Dist., ew Taipei City 235, Taiwan (R.O.C.) Block Diagram:PD4 REGUATOR G2 G1 PWM S- S+ De-rating Curve: 20 Output De-rating Vs Input Voltage: Ta= (HORIZOTA) ~ Dimension: AMBIET TERRATURE( ) IPUT VOTAGE (VAC) Hz (Unit: mm) OTES: TERMIA BOCK: =3P, P=9.5mm MODE o SPU-250P-IDx TERMIA BOCK: O/P:6P, P=9.5mm MODE o SPU-250P- IDx G1 G1 G2 Copy Right Sunpower Technology Corp. 2009, All Rights Reserved. SPU-250P-IDx Rev 0.2 RS MAY

5 SPU-250P-Qx Series Features: * Universal AC input with active power factor correction, P.F.>0.95 * High efficiency and high reliability * Built-in filter, low ripple noise * -20 ~70 Operating temperature * U, cu, TUV, CB, CE standard * 3 years warranty Specification: Voltage IPUT OUTPUT PROTECTIO 88V ~ 264VAC universal full range or 125V ~ 375VDC. Frequency Hz Current <3.5A@VAC input, full load condition Inrush Current <35A@115V, <70A@230V AC input. Cold start at 25 ambient eakage Current <1.5mA@264V AC input Power Factor PF > 0.95 MODE o. SPU-250P-Q1 SPU-250P-Q3 SPU-250P-Q4 Voltage V3 V4 V3 V4 V3 V4 5V 12V -12V -5V 5V 12V 24V -12V 5V 15V 24V -15V Min oad 1A 0.5A 0A 0A 2A 1A 0A 0A 2A 1A 0A 0A Max oad 15A 15A 1A 1A 15A 12A 4A 1A 15A 10A 4A 1A Output Tolerance 2 ±3% ±3% ±5% ±5% ±3% ±3% ±5% ±5% ±3% ±3% ±5% ±5% Ripple oise MAX. 3 70mV 120mV 150mV mv 70mV 120mV 200mV 150mV 70mV 150mV 200mV 150mV Efficiency (TYP.) 81% 82% 82% Output MAX. 250W 250W 250W MODE o. SPU-250P-Q5 SPU-250P-Q7 --- Voltage V3 V4 V3 V V 3.3V 12V -12V 5V 3.3V 24V 12V Min oad 1A 0A 0.5A 0A 2A 0A 0A 1A Max oad 15A 15A 12A 1A 15A 15A 4A 10A Output Tolerance 2 ±3% ±3% ±3% ±5% ±3% ±3% ±8% ±3% Ripple oise MAX. 3 70mV mv 120mV 150mV 70mV mv 200mV 150mV Efficiency (TYP.) % 81% --- Output MAX. 250W 250W --- ote *SPU-250P-Q7,V4 : +12V, SPU-250P-TxA is with V3, TxB is with V4 SPU-250P-Q1,Q3 : :5.8 ~ 7V;:13.8 ~ 16.8V ; SPU-250-Q4 : :5.8 ~ 7V;:17.3 ~ 21V; SPU-250P-Q5 : :5.8 ~ 7V;:3.8 ~ 4.6V;V3:13.8~ 16.8V; Over Voltage SPU-250P-Q7 : :5.8 ~ 7V;:3.8 ~ 4.6V;V4:13.8~ 16.8V; Shutdown and latch off, recover after re-start up. Over oad Short Circuit When power supply over 105%~ 150 max load or short circuit acted, power supply will be shutdown and recover automatically after the fault is removed. Rise time <20mS EEC. CHAR. Hold up time >20mS@230V Setup time <2 Sec@ 2V AC Temperature 4 Operating: -20 ~ +70 ; De-rating: 45 ~ 70 : 2.5%/ ; Storage: - ~ +85 EVIROMET Humidity Operating: 20% ~ 90% RH (non condensing) ; Storage: 10% ~ 95% RH (non condensing) Withstand voltage -O/P:3KVAC, -:1.5KVAC, O/P-:0.5KVAC, 1minute SAFETY Isolation resistance -O/P, -, O/P- >MΩ/500VDC at 25 / 70% RH Safety standard U nd,csa C22.2 o nd,tuv E 950-1:2006+A11+A1+A12,IEC 950-1:2005+A1, standard. E CASS B FCC CFR 47 PART 15 CASS B CS CASS B. EMC Compliance to E-3-2 CASS D, E-3-3 EMS E 55024:E -4-2,3,4,5,6,8,11 Cooling atural cooling, When output exceed % OAD, a 18 CFM(min) DC fan is required OTHERS M.T.B.F. K hours Packing.W.: Kg / 1pc; 18 pcs / 1.38 CUFT / 1 CT OTE 250W, Quad Output Active P.F.C Function 198 x 97 x 38 mm 7.8 x 3.82 x 1.50 inch 1 All measurements which not mentioned are based on 230VAC input, output max. at ambient 25 / 70%RH 2 Output tolerance included set up voltage, line regulation and load regulation. The regulation is measured at the condition:when any of output is with 20% ~ % max load and the rest of each outputs are with % max load, Each output could work within max load but must under total output max. 3 Ripple noise are measured at condition and 20MHz of bandwidth by using a twisted pair-wire terminated with a 0.1uF a 47uF parallel capacitor. 4 The operating temperature shall follow the de-rating curve in spec The output load may be requested for decreasing as de-rating curve in spec when low input voltage is under VAC 5 The power supply is considered a component of end-equipment. The end-equipment must be re-confirmed whether comply with EMC directives. Copy Right Sunpower Technology Corp. 2009, All Rights Reserved. SPU-250P-Qx Rev 0.3 RS OV

6 SPU-250P-Qx Series Block Diagram:PQ12 SPU-250P-Q1 Q4 REGUATOR V4 REGUATOR V3 SYCHROIZE COM PWM SPU-250P-Q5 REGUATOR V4 SYCHROIZE V3 COM PWM SPU-250P-Q7 V3 SYCHROIZE V4 COM PWM Copy Right Sunpower Technology Corp. 2009, All Rights Reserved. SPU-250P-Qx Rev 0.3 RS OV

7 SPU-250P-Qx Series De-rating Curve: 20 ATURA COOIG FORCED AIRFOW COOIG > 18CFM Output De-rating Vs Input Voltage: Ta=25 Dimension: (HORIZOTA) ~ IPUT VOTAGE (VAC) Hz (Unit: mm) OTES: TERMIA BOCK: =3P, P=9.5mm MODE o SPU-250P-Qx TERMIA BOCK: O/P:6P, P=9.5mm MODE o SPU-250P- Qx GD GD V3 V4 Copy Right Sunpower Technology Corp. 2009, All Rights Reserved. SPU-250P-Qx Rev 0.3 RS OV