C-more Selection Guide & Specifications

Transcription

1 Selection Guide & Specifications Model 8 TFT color 10 TFT color 12 TFT color 15 TFT color Specification Part Number EA7-T8C EA7-T10C EA7-T12C EA7-T15C Price Display Actual Size and Type 8.4" TFT color 10.4" TFT color 12.1" TFT color 15.0" TFT color Color Scale 65,536 colors Display Viewing Area 6.73" x 5.05" [170.9 mm x mm] 8.31" x 6.24" [211.2 mm x mm] 9.47" x 7.62" [240.6 mm x mm] 11.97" x 8.98" [304.1 mm x mm] Screen Pixels 640 x 480 (VGA) 800 x 600 (SVGA) 1024 x 768 (XGA) Display Brightness 300 cd/m 2 (NITS) 270 cd/m 2 (NITS) 260 cd/m 2 (NITS) 220 cd/m 2 (NITS) LCD Panel Dot Pitch mm x mm 0.33 mm x 0.33 mm mm x mm mm x mm Backlight Average Lifetime* Approximately 50,000 hours Backlight User Replaceable - Part Number EA-xx-BULB, xx = panel size Touch Panel Type Analog Resistive (10-bit resolution, 1024 x 1024 touch area) Analog Resistive (12-bit resolution, 4096 x 4096 touch area) CPU Type 32-Bit RISC CPU (400 MHz) 32-Bit RISC CPU (400 MHz) Plus Graphic Accelerator Chip Battery Replaceable battery ADC Part # D2-BAT-1 (Manufacturer Part # CR2354) System Memory SDRAM 32 MBytes SDRAM 64 MBytes System Flash Memory FLASH 32 MBytes FLASH 64 MBytes Backup Memory (SRAM) Control data backup memory (SRAM) 256 KBytes Logging Data Memory CompactFlash Memory Card p/n EA-FLASH-128MB, industrial grade, high speed (Optional) or USB Pen Drive p/n SDCZ4-512-A10 (Optional) Number of Screens Up to 999 limited by available project memory (10 MBytes) Up to 999 limited by available project memory (40 MBytes) Realtime Clock Built into panel ( clock is still accessible if available) Calendar Month/Day/Year - battery backup Screen Saver, backlight turns off after a minute adjustable time, or can be disabled Serial Interface Serial : RS-232C/422/ Pin D-sub (female) USB Type B Download/Program USB type B (ver. 1.2) USB Type A for USB device options type A (ver. 1.2) 10/100 Base-T Audio Line Out Audio Line Out, 1 Volt rms, stereo requires amplifier and speaker(s) CF Card Slot #1 Optional: CompactFlash Memory Card p/n EA-FLASH-128MB, industrial grade, high speed, CF slot #1 located on top side of touch panel. Expansion Assembly (p/n EA-EXP-OPT) Optional: Use the CF Card Interface Module p/n EA-CF-IF in the right slot of the Expansion Assembly for installing CF card - Slot #2. The left slot of the Expansion Assembly is for future options. Supply Power 24 VDC, -15%, +20% ( VDC operating range) (Use an AC Power Adapter, p/n EA-AC, to power the touch panel from a VAC, 50/60 Hz. power source.) Power Consumption VDC VDC VDC VDC Recommended Input Fuse 3.0 A DC slow blow Operating Temperature 0 to 50 C (32 to 122 F) Storage Temperature 20 to +60 C ( 4 to +140 F) Humidity 10 85% RH, non-condensing Noise Immunity Noise voltage: 1000 Vp-p, Pulse width: 1 µs, Rise time: 1 ns Withstand Voltage 1000 VDC for 1 minute, between DC power supply input terminal and safety ground Insulation Resistance Over 20 M between DC power supply input terminal and safety ground Vibration IEC compliant, Hz: mm amplitude, Hz 1.0 G: 10 sweep cycles per axis on each of 3 mutually perpendicular axes Shock 15 G peak, 11 ms duration, 2 shocks per axis, on 3 mutually perpendicular axes Enclosure NEMA 4/4X, IP-65 (When mounted correctly. For indoor use only.) Agency Approvals UL, cul, CE Dimensions 8.748" x " x 2.053" [222.2 mm x mm x 52.1 mm] " x " x 2.079" [271.0 mm x mm x 52.8 mm] " x " x 2.075" [280.0 mm x mm x 52.7 mm] " x " x 2.048" [330.2 mm x mm x 52.0 mm] Weight 2.60 lb. [1,180 g] 3.55 lb. [1,610 g] 4.59 lb. [2,080 g] 7.01 lb. [3,180 g] * NOTE: The backlight average lifetime is defined as the average usage time it takes before the brightness becomes 50% of the initial brightness. The lifetime of the backlight depends on the ambient temperature. The lifetime will decrease under low or high temperature usage Operator Interface

2 R 10" TFT Color Touch Panel - Full Model Overview The 10 TFT color full featured touch panel uses a 10.4" diagonal analog (1024 X 1024) touch screen with a 640 x 480 (VGA) pixel resolution TFT LCD (liquid crystal display) with 65K colors. 10 touch panels can be directly mounted into any EZTouch 10 touch panel cutouts. Part No. EA7-T10C DL05/06 Features 10.4" diagonal color TFT (Thin Film Transfer) LCD display with 65K colors 640 x 480 pixel resolution 270 NITS display brightness 50,000 hour average backlight lifetime, user replaceable Analog resistive (1024 X 1024) touch screen allowing unlimited touch areas USB port B (program/download) and USB port A (USB device options) 10/100 Base-T port (program/download & comm) Serial interface (RS-232/422/485) 1 GByte CompactFlash card slot, built-in Expansion assembly (optional) for CompactFlash devices (use with optional CF Card Interface Module) 24 VDC powered, 110 VAC power adapter (optional) Audio Line Out, stereo - requires amplifier and speaker(s) 10 MByte project memory Data logging 0 to 50 C (32 to 122 F) operating temperature range NEMA 4/4X, IP-65 compliant when mounted correctly, indoor use only Slim design save panel space UL, cul & CE agency approvals 2-year warranty from date of purchase [22.27] Mounting Brackets (6) places [ ] [ ] CUTOUT [42.8] Mounting Cutout Function Available Associated Features USB Compact Flash Expansion Assembly Audio Out FTP - - Web Server Data Logging Data Logging/Project CF Module & future modules Speaker/Amplifier Connection [22.27] [22.25] Dimensions [300.2] [347.0] Gasket Units: inches [mm] [271.0] [224.2] C CF Slot #1 (Top of Panel) UL US Mounting Bracket (6) places Drivers Serial Avail. Direct LOGIC K-sequence Modbus (Koyo Addressing) Allen-Bradley DF1 Full Duplex Allen-Bradley DF1 Half Duplex Allen-Bradley 5 DF1 Allen-Bradley DH485 Modbus RTU Entivity Modbus RTU GE Fanuc SNPX (90/30, 90/70) Omron HostLink (C200, C500) Mitsubishi Melsec FX Direct LOGIC Modbus TCP/IP Allen-Bradley /IP * Entivity Modbus TCP/IP * ControlLogix and CompactLogix s & Memory Expansion DC Power Label Optional Expansion Assembly Location Field I/O Software HMIs Other HMI AC Drives Motors Steppers/ Servos Motor Controls Proximity Photo Limit Switches Encoders Pushbuttons/ Lights Process Relays/ Timers Comm. TB s & Wiring Power Cutout Outline [ ] Enclosures Bezel Outline Units: inches [mm] [113.25] Serial Communications Product Label Appendix Part Index [22.25] For Future Use Audio Line Out USB B (Programming/ Download) 10/100 Base-T ( Communications, Programming/Download) USB A (Device Options) Operator Interface 9 37

3 Communication s Compact Flash memory slot #1 is located at the top of panel. Serial Communications Frame GND 2 TXD (232C) 3 RXD (232C) 6 LE 11 TXD+ (422/485) 7 CTS (232C) 12 TXD (422/485) 8 RTS (232C) 13 Term. Resistor 4 Vcc 9 RXD+ (422/485) 14 do not use 5 Logic GND 10 RXD (422/485) 15 do not use For Future Use Bottom View Audio Line Out, stereo, 1 Volt rms, 3.5mm Mini Jack (Amplifier Required) USB - Type B Programming/Download 1 Vbus 2 D 3 D+ 4 GND Shell Shield USB - Type A USB Device Options 1 do not use 2 D 3 D+ 4 GND 10/100 Base-T Communications, Programming/Download 1 TD+ 2 TD 3 RD+ 4 do not use Link Status LED (Green) On Linked Off No Comm do not use 6 RD 7 do not use 8 do not use Network Activity LED (Orange) On Active Network Data Off Network Idle Note: Device is not available on Base Feature touch panels, part numbers EA7-S6M-R and EA7-S6C-R. Note: Use USB Programming Cable, p/n USB--AB15. The port has several uses: Download program to panel Communicate to s/pcs Send Access FTP server Act as a Web server The port has an RJ-45 8-wire modular connector with green and orange LEDs. The orange LED indicates the communication status. It illuminates when there is data activity on the network. The green LED indicates link status and illuminates when a link is established. connections to s/pcs: DirectLOGIC Modbus TCP Allen-Bradley EtherNet/IP (ControlLogix and CompactLogix ) Entivity Modbus TCP/IP Note: The base panels (-R part numbers) do not include an port, and do not have these capabilities. USB B Program via the USB programming port. It's fast and easy, with no baud rate settings, parity, or stop bits to worry about. We stock standard USB cables for your convenience. USB B can be used to upload or download projects to and from a PC. USB A The Universal Serial Bus (USB) A is a standard feature for all models and can be used to connect various USB HID (Human Input Device) devices to the panel, such as: USB pen drives, (SDCZ4-512-A10) USB keyboards USB barcode scanners USB card scanners can log data to the USB pen drive as well as load projects to the panel from the pen drive. You can also back up project files and panel firmware. Sound Interface (Audio Line Out) When attached to an amplifier and speaker(s), can play warning sounds or pre-recorded messages such as: "conveyor is jammed". supports WAV type files. The output is stereo. The port is an RS-232, RS-422 or RS- 485 female 15-pin D-sub connector. Use this port for serial connections to s. The port supports the following protocols: All AutomationDirect.com DirectLOGIC s: DirectLOGIC K-sequence DirectNET Modbus (Koyo Addressing) Allen Bradley: DF1 Full Duplex DF1 Half Duplex 5 DF1 DH485 Modbus RTU Entivity Modbus RTU GE Fanuc SNPX (90/30, 90/70) Omron HostLink (C200, C500) Mitsubishi Melsec FX 9 40 Operator Interface

4 Communication Protocols & Cables Overview DL05/06 Compatibility Table /Network Model Protocols Allen-Bradley MicroLogix 1000/1200/1500, SLC 500, 5/01, /02, /03 MicroLogix 1000,1200 and 1500 SLC 5/03, /04, /05-5 DH485/AIC/AIC+ DF1 Half Duplex; DF1 Full Duplex DF1 Half Duplex; DF1 Full Duplex DF1 Full Duplex /IP /IP (ControlLogix and CompactLogix only) EtherNet/IP Modbus TCP/IP Modbus TCP/IP devices Modbus TCP/IP GE 90/30 and 90/70 SNPX Mitsubishi FX Series FX, Direct Modicon 984 CPU, Quantum 113 CPU, AEG Modicon Micro Series 110 CPU: 311-xx, 411-xx, 512-xx, 612-xx Modbus RTU Omron C200, C500 Host Link DirectLOGIC DL05/DL06 H0-ECOM/H0-ECOM100 Direct LOGIC D2-230 D2-240 D2-250/D /D2-260 D2-240/D /D2-260 Using DCM H2-ECOM/H2-ECOM100 D3-330/330P (Requires the use of a Data Communications Unit) Direct LOGIC D3-340 D3-350 D3-350 DCM Cable Description Direct LOGIC RJ-12 port, DL05, DL06,,, D3-350, D4-450 & H2-Win (RS-232) Direct LOGIC (VGA Style) 15-pin port, DL06, D2-250 (250-1), D2-260 (RS-232) Cable Part Number Price EA-2 EA-2-1 Direct LOGIC RJ-11 port, D3-340 (RS-232) EA-3 Direct LOGIC 15- pin D-sub port, (RS- 232) EA-4-1 Direct LOGIC 25-pin D-sub port,, D3-350, EA-4-2 DCU and all DCM s (RS-232) Allen-Bradley MicroLogix 1000, 1200 & 1500 (RS-232) Allen-Bradley SLC 5-03/04/05 DF1 port (RS-232) Allen-Bradley -5 DF1 port (RS-232) EA-MLOGIX- EA-SLC-232- EA Allen-Bradley SLC 500 DH485 port (RS-232) EA-DH485- GE 90/30 and 90/70 15-pin D-sub port (RS-422) EA MITSUBISHI FX Series 25-pin port (RS-422) MITSUBISHI FX Series 8-pin mini-din (RS-422) OMRON C200, C500 (RS-232) EA-MITSU- EA-MITSU- -1 EA-OMRON- NOTE: EZTouch serial communication cables are compatible with touch panels. EA-2 Field I/O Software HMIs Other HMI AC Drives Motors Steppers/ Servos Motor Controls Proximity Photo Limit Switches Encoders Pushbuttons/ Lights Process Relays/ Timers Comm. D4-430 TB s & Wiring D4-440 D4-450 EA-2-1 Power Enclosures Appendix All with DCM Part Index H4-ECOM/H4-ECOM100 H2-Win (Think & Do) Live V5.2 or later and Studio any version H2-Win (Think & Do) Live V5.5.1 or later and Studio V7.2.1 or later Direct LOGIC Think & Do Modbus RTU (serial port) Think & Do Modbus TCP/IP ( port) Operator Interface 9 41

5 1 Computer Programming Connections Using the Programming Software for project development, the touch panel can be connected to a PC (personal computer) in one of several ways: Connect a USB Programming Cable (USB--AB15) from a USB port type A on the PC to the USB type B programming port on the touch panel. The USB connection is for direct connection only and does not support USB hubs. Connect the touch panel to a PC via an hub or switch, and CAT5 cables (full feature panels only). Multiple panels can be programmed in this configuration. Use an crossover cable directly between the touch panel s port and the PC port (full feature panels only). Following are the minimum system requirements for running Programming Software, p/n EA-PGMSW, on a PC: Personal Computer with a 333 MHz or higher processor (CPU) clock speed recommended; Intel Pentium/Celeron family, or AMD K6/Athlon/Duron family, or compatible processor recommended Keyboard and Mouse or compatible pointing device Super VGA color video adapter and monitor with at least 800 x 600 pixels resolution (1024 x 768 pixels recommended) 64K color minimum 300 MB free hard-disk space 128 MB free RAM (512 MB recommended) CD-ROM or DVD drive for installing software from the CD USB port or 10/100 Mbps port for project transfer from software to touch panel ( port not available on -R models) Operating System - Windows XP Home / Professional Edition Service Pack 2 or Windows 2000 with Service Pack 4 USB Programming Cable Part No. USB--AB15 Other lengths available see USB--AB3, USB--AB6, USB--AB10 on page 9-27 Message in from a device Switch (switching hub) Message is sent out only from the port connected to destination device PC USB Connectivity Touch Panel USB Type B Programming/Download USB Type A USB--AB15 Part No. E-SW05U Connectivity via a Hub or Switch Hub or Switch 10/100 Base-T ACT/ 10/ ACT/ 10/ ACT/ 10/ ACT/ 10/ ACT/ 10/ LNK 100 LNK 100 LNK 100 LNK 100 LNK 100 Uplink E SW05U Touch Panel Configuration Kit PC (Bottom View) CAT5 Cable - Straight-thru Part No. RT-CNFGKIT PC Direct Connection Touch Panel CAT5 Cable - Crossover (Bottom View) The Configuration Kit includes a five-port 10/100 Base-T switch, four straight-through cables, and one crossover cable. (The cables are at least five feet in length.) The kit provides a great convenience for configuring systems, demonstration systems or basic control projects using Operator Interface

6 Power Connection Wiring Providing Power to the Touch Panel Connect a dedicated 24 VDC switching power supply rated for a minimum of 1.5 Amps to the DC connector on the rear of the touch panel. Connect the ground terminal to a proper equipment ground. or, install a AC Power Adapter (EA-AC) to the rear of the touch panel and connect an AC voltage source of VAC, 50/60Hertz, to its AC connector. then, turn on the power source and check the LED status indicators on the rear of the touch panel for proper operation. DC Wiring AC Wiring Overview DL05/06 Field I/O Software 24 VDC; -15%, +20% ( VDC) Recommended Fuse 3 A slow blow + NOT Used 24V Dedicated power supply recommended AC Power Adapter Not recommended for use with the EA7-T15C when operating temperatures are expected to be above 40 deg C. HMIs Other HMI AC Drives Equipment Ground GND CPU Motors Recommended Power Supply: AutomationDirect Part No. PS24-050D BATT VAC 50/60 Hz AC Power Adapter EA-AC Steppers/ Servos Motor Controls Proximity Photo LED Status Indicators Limit Switches CPU Status LED (Green, Orange & Red) Off Power Off Green Red Blinking Red Blinking Orange Blinking Green Normal CPU Run State Memory Error Operating System not found LCD Backlight Failure Power Loss Detection CPU TxD RxD BATT IOlOl Rear View Power LED (Green) On Power On Off Power Off Serial TxD/RxD LED (Green) On Comm. is active Off No communication Encoders Pushbuttons/ Lights Process Relays/ Timers Comm. TB s & Wiring WARNING: To minimize the risk of potential safety problems, you should follow all applicable local and national codes that regulate the installation and operation of your equipment. These codes vary from area to area and it is your responsibility to determine which codes should be followed, and to verify that the equipment, installation, and operation are in compliance with the latest revision of these codes. Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes and standards. We do not guarantee the products described in this publication are suitable for your particular application, nor do we assume any responsibility for your product design, installation, or operation. If you have any questions concerning the installation or operation of this equipment, or if you need additional information, please call us at or This publication is based on information that was available at the time it was printed. At Automationdirect.com we constantly strive to improve our products and services, so we reserve the right to make changes to the products and/or publications at any time without notice and without obligation. This publication may also discuss features that may not be available in certain revisions of the product. Power Enclosures Appendix Part Index Operator Interface 9 43