Design-in guide. Philips CertaFlux PLM II Gen1

Transcription

1 Design-in guide Philips CertaFlux PLM II Gen1 April

2 Contents Contents Introduction to this guide 1 Information and support 1 Introduction to the Certaflux PLM II Gen1 2 Applications 2 Product description 2 The CertaFlux PLM II system components 2 Performance specification 4 Typical operating conditions 4 Performance specifications CertaFlux PLM II 3000lm 740 Gen1 4 Performance specifications CertaFlux PLM II 3000lm 850 Gen1 5 Specified lifetime performance 6 Optical distributions 7 Optical performance of CertaFlux PLM II Gen1 7 Recommendations for SON-T replacements 8 Lighting characteristics 10 Light distribution 10 Optical files 10 Color consistency (SDCM) 10 Product dimensions 11 Important recommendations and warnings 12 Installation instructions 12 Design-in phase 12 Installation and service phase of luminaires 13 Installation instructions 14 1-n connector fixation 15 Module placement in a luminaire 16 Fixation of the driver 16 Surge Protection in a CertaFlux PLM II system 16 Thermal management 17 Thermal specifications 17 Operating temperature 17 Module temperature 18 Recommendations for module clusters in luminaire fixture design 20 Xitanium LED driver temperature 21 Please refer to individual product datasheets for Tcase max information. 21 Quality 22 Compliance and approval marks 22 Sustainability 22 Warranty 22 IP rating 22 Photobiological safety 22 EMC 23 Electrostatic discharge (ESD) 23 Remote system operation 24 Use of circuit breakers: Xitanium LED drivers 24 Note on conditions for storage, transportation and operation24 During operation 24 System disposal 25 Contact details 26 Philips PLM II Gen1 26 Thermal management partners 26 Mechanical fixation 14 Wiring 15

3 Introduction to this guide Thank you for choosing the Philips CertaFlux PLM II Gen1. In this guide you will find the information you need to design this system into a luminaire. This edition describes the performance, technical details of CertaFlux PLM II Gen1. Extensions to the range will be included in future updates of this guide. We advise you to consult our websites for the latest up-to-date information. Philips CertaFlux PLM II Gen1 Information and support If you require any further information or support please consult your local Philips office or visit: OEM website Xitanium drivers Note LED technology is continuously improving. For the latest updated information, please check 1

4 Introduction to the Certaflux PLM II Gen1 Applications The Philips CertaFlux PLM II Gen1 has been developed primarily for outdoor applications. Figure 1. CertaFlux PLM II Gen1 Product description To operate a system you will need the following products, which are sold separately: One or more CertaFlux PLM II LED modules, Table1 Specified connectors, Table1 Compatible Xitanium LED driver, Table 2 Figure 2. CertaFlux PLM 1-3 multi-connector Classification The CertaFlux PLM II Gen1 with Xitanium driver listed below can be used in: Class I IEC isolation systems IMPORTANT USAGE NOTES Tcase,max must not exceed 75 C for Ta 30 o C ΔT (Tambient -Tcase) must not exceed 45 C Failure to comply with usage conditions will void product warranty The CertaFlux PLM II system components Figure 3. CertaFlux PLM 1-5 multi-connector Table 1. CertaFlux PLM II and 1-n multi-connector Product GPC CertaFlux PLM II 3000lm 740 Gen CertaFlux PLM II 3000lm 850 Gen CertaFlux PLM 1-3 multi-connector CertaFlux PLM 1-5 multi-connector CertaFlux PLM II system with Xitanium LED drivers, Class I The following drivers are highly recommended to operate the CertaFlux PLM II outdoor modules. If other drivers are connected to PLM II, please contact with your local sales representative for further confirmation, it can void warranty. 2

5 Table 2. CertaFlux PLM II system with fixed Xitanium LED drivers, Class I compliant Number of CertaFlux PLM Max output current Driver GPC Cable II (any type) (ma) 3x-5x 700 Xitanium 150W 0.70A 230V IP x CertaFlux PLM 1-5 multi-connector Xitanium 150W 0.70A 230V-6P I x CertaFlux PLM 1-3 multi-connector Xitanium 150W 0.70A 1-10V IP x 700 Xitanium 75W 0.70A 230V IP x CertaFlux PLM 1-3 multi-connector Xitanium 75W 0.70A 230V-3P I x 700 Xitanium 50W 0.7A 230V IP No additional Cable needed Table2 includes fix output and single output dimmable drivers, for non IP66 drivers i.e. IP42 150W, please contact with local sale representative. As the Xitanium LED driver portfolio is always expanding to include new products, please visit or contact your Philips sales representatives for the latest system combinations. 3

6 Performance specification The following paragraphs contain the performance specifications of the CertaFlux PLM II Gen1 modules. Typical operating conditions Table 3. Typical operating conditions Item Symbol Unit Value Description Default Driver current Idriver ma 700 Fixed output driver current Case temperature Tcase C 65 Case temperature: typical temperature at which the module operates within specs Ambient temperature Tamb C 30 Ambient temperature outside luminaire Note: Philips maintains a tolerance of ±6.5% on luminous flux measurements, ±0.06 V on forward voltage measurements, ±2 on CRI measurements and ±5% on CCT measurements Performance specifications CertaFlux PLM II 3000lm 740 Gen1 CertaFlux PLM II 3000lm 740 Gen1 performance at 700mA and Tcase = 65 C Table 4. Performance specification of the CertaFlux PLM II 3000lm 740 Gen1under typical operating conditions (If = 700 ma and Tcase = 65 C). Item Min Typ Max Unit Initial lumen output lm Initial efficacy lm/w Forward voltage V Initial power consumption W Correlated Color Temperature (CCT) K Color Rendering Index (CRI) 70 - Ra Initial color accuracy - 6 SDCM Operating Ta range o C Weight 0.6 Kg Approbation CQC,CE,CB, ENEC 4

7 IP rating Insulation class IP66 III IMPORTANT USAGE NOTES PLM Systems with recommended Xitanium drivers should be installed in Class I luminaires only. For Class II luminaires additional isolation layer for the driver is needed. Design-in support is available please contact your local Philips sales representative for additional information. Figure 4. Estimated module flux and module efficacy of the CertaFlux PLM II 3000lm 740 Gen1 under typical driver current 700 ma and various case Temperatures (Tcase) Performance specifications CertaFlux PLM II 3000lm 850 Gen1 CertaFlux PLM II 3000lm 850 Gen1 performance at 700mA and Tcase = 65 C Table 5. Performance specification of the CertaFlux PLM II 3000lm 850 under typical operating conditions (If = 700 ma and Tcase = 65 C). Item Min Typ Max Unit Initial lumen output lm Initial efficacy lm/w Forward voltage V Initial power consumption W Correlated color temperature (CCT) K Color Rendering Index (CRI) 80 - Ra Initial color accuracy - 6 SDCM Operating Ta range o C Weight 0.6 Kg 5

8 Approbation IP rating Insulation class CQC,CE,CB, ENEC IP66 III IMPORTANT USAGE NOTES PLM Systems with recommended Xitanium drivers should be installed in Class I luminaires only. Figure 5. Estimated module flux and module efficacy of the CertaFlux PLM II 3000lm 850 Gen1 under typical driver current 700 ma and various case Temperatures (Tcase) Specified lifetime performance Figures 6. show the expected lumen maintenance over a typical product (both 850 and 740 as well) lifetime 6

9 Optical distributions Optical performance of CertaFlux PLM II Gen1 Figure 7. CertaFlux PLM II Figures 8. Polar intensity diagram, PLM II Gen1 PLM II is designed for narrow roads and urban street lighting. Figure 9. Example of application rendering, PLM II 7

10 N.B. Component and process tolerances can result in imperfectly symmetrical light distributions. Maximum acceptable tolerances will have minimal impact on optical distributions and optical performance in the final application for a variety of reasons (e.g. light from neighboring poles, flux differences < 20% not visible for the human eye). All polar intensity diagram illustrations are just an indication of the beam shape. We suggest making use of the IES files available on the CertaFlux PLM II module website. Recommendations for SON-T replacements The recommendations are made by means of Dialux simulations for specific road examples as mentioned in tables x,x x. The road width (w), pole height (H), pole distance (P), tilt angle (T) and overhang (O) are specified per application. Figure 10: Specified installation parameters For road properties the following settings have been used for all three applications; Road type: Asphalt pavement ; Reflection table: CIE R3; Q0 of table: 0.07; SON-T 150W replacement solution We propose to replace a 150W SON-T conventional luminaire with a system of 3 x PLM 3000lm and 1 Xitanium 150W IP67 driver. The recommended system can meet the requirement of standard for lighting design of urban road in China. Figure 11: Application rendering of 10m road with single installation Remark: CJJ is regulation of China 8

11 SON-T 250W replacement solution We propose to replace a 250W SON-T conventional luminaire with a system of 5 x PLM 3000lm and 1 Xitanium 150W IP67 driver. The recommended system can meet the requirement of standard for lighting design of urban road in China. Figure 12: Application rendering of 15m road with single installation SON-T 400W replacement solution We propose to replace a 400W SON-T conventional luminaire with a system of 8 x PLM 3000lm and 2 Xitanium 150W IP67 drivers. The recommended system can meet the requirement of standard for lighting design of urban road in China. Figure 13: Application rendering with double installation of 19m road and central reserve Figure 14: Road application with 4 lanes and central reserve 9

12 Cie y CRI K 6.0 SDCM CRI K 6.0 SDCM BBL Cie x

13 Product dimensions Dimensions of CertaFlux PLM II Figure 16. CertaFlux PLM II (any type) Module Type A1 A2 B1 C1 C2 D1 CertaFlux PLM II 3000lm Gen Dimensions of connecting cable Figure17. CertaFlux PLM 1-3 multi-connector Figure 18. CertaFlux PLM 1-5 multi-connector 11

14 Important recommendations and warnings The following recommendations and warnings should be taken into account when designing PLM II in a luminaire. Installation instructions Please refer to section xxx for module and driver wiring and proper module placement in a luminaire. CertaFlux PLM II is a product with integrated heatsink. The heatsink can warrantee the lifetime performance of the product if certain precautions are taken into account in luminaire design. Refer to section Thermal Management CertaFlux PLM II is a product with integrated optics. No additional secondary optics are needed. CertaFlux PLM II is an IP66 rated module. Recommended Xitanium LED drivers are IP67. For IP66 applications no additional efforts are needed. Min module mounting pitch is 5mm. IMPORTANT USAGE NOTES (approval from Alex) Tcase,max must not exceed 75 C for Ta 30 o C ΔT (Tambient -Tcase) must not exceed 45 C Failure to comply with usage conditions will void product warranty Design-in phase It is recommended to use the approved Philips Xitanium LED drivers. For a list of approved drivers please see Tables 2. If drive PLM II with other drivers not in table 2, please contact your local Philips sales representative for additional confirmation. Safety and IEC/CQC recommendations: the general IEC/CQC recommendations for luminaire design and national safety regulations (ENEC, CE, CB, etc.) also apply to selected PLM II modules and Xitanium LED drivers. Luminaire manufacturers are advised to conform to the international standards for luminaire design (IEC Luminaires). Do not apply mains power directly to the LED module. 12

15 Do not use damaged or defective modules. Do not drop the LED module or let any object fall onto it as this may damage the module. Do not use the LED module if it has been dropped or an object has fallen onto it and there are visible defects or damage. Installation and service phase of luminaires The luminaire should not be serviced while the mains voltage is connected; this includes connecting or disconnecting the PLM II module cable. Hot switching is not allowed. The following recommendations and warnings should be taken into account when using PLM II modules and Xitanium LED drivers. 13

16 Installation instructions Warning! The CertaFlux PLM II should always be replaced by an OEM-qualified installer. Special attention should be paid to the following points: Do not service the system when the mains voltage is connected; this includes connecting or disconnecting the cable The water proof connector has to be fully tightened up to prevent the water penetration via the connection in the field application. Mechanical fixation The separate components (driver and module/s) of the PLM II system can be fixed in place securely using the mounting holes located on the module(s) and driver. Please refer to the dimensional drawings for specific details. The 3D CAD files can be downloaded from the Philips Technology website at Figure 19. Screw To fix the system in place we recommend using an M4 hexagonal socket-head cap screw with an M4 spring-lock washer for screws with cylindrical heads. In a system with multiple modules, it is recommended that the modules are mounted with min distance of 5 mm. 14

17 Notes: 1. means the input connector of cable; no. 1-5 is the output connector of cable. 2. Each output connector can be connected or not. But an end cap must be in place when you leave any connector open. As the internal connection of these connectors are in series, which means if any one of them is open, there will be no output. Wiring A Xitanium 150w outdoor driver can support up to 3~5 CertaFlux PLM II modules in series and a Xitanium 75W outdoor driver can support 2 CertaFlux PLM II modules in series. The below is the connections we recommend. Philips SPD + Xitanium 150W/75W outdoor driver + CertaFlux PLM II modules 3. For easy installation, we strongly suggest you to leave the first or last one connector open (with an end cap) when not all of the connectors are necessary. 4. SPD is used to strength the surge handling capability of your luminaire; it is an optional device here. Figure 20. Wiring Philips SPD+ Xitanium 150W/75W outdoor driver+ CertaFlux PLM II 1-n connector fixation PLM II modules can be connected using the cable interface as specified below. This cable allows connection with fixed and dimmable single output drivers and serial connection from 1 and up to 5 modules. To secure the long term reliability of the module and application, below instructions have to be followed strictly. Figure n cable Putting too much stress on the cables or bending the cables with too much angle can cause seals to leak. The diameter of the bending circle should not exceed 25mm. The water proof connector has to be fully tightened to prevent the water leaking into the connection in the filed application. A bulge structure on the connector as the position indicator. Intense exposure of connectors, cables and 1-n multi-connectors to sunlight (UV) will make the seals brittle over time causing water leaks. It s recommended to cover the electrical connections to avoid this risk, also to avoid cables being damaged by wildlife. Cannot be used in a marine environment without additional protection against salt 15

18 Module placement in a luminaire Please follow remark on PLM II module as below picture for installing the module to right direction, this is critical to get the correct light distribution. Figure 22. Please install the module as arrow to road side direction Fixation of the driver The Xitanium driver has fixation holes at the short ends of the casing. The driver should be mounted securely on a flat part of the luminaire, using the mounting hole on each side of the driver. Please refer to the specific Xitanium LED driver product datasheet and design-in guide for individual product dimensions and installation instructions. Surge Protection in a CertaFlux PLM II system CertaFlux PLM II has a high level of integrated protection against the adverse effects of external surges and electro-static discharges. For optimum system protection, apply external common-mode and differential-mode surge protection at luminaire level in order to mitigate the harmful effects of surges on the LED driver and the CertaFlux PLM II. More details on surge protection can be found in the Application Design-In Guide for the Philips 277V SPD Surge Protection Device. 16

19 Thermal management The critical thermal management points for the module and driver are set out in this chapter in order to facilitate the design-in of the PLM II module. Keeping these thermal points in mind will help to ensure the optimal performance and lifetime of the system. Thermal specifications The main thermal specification that needs to be taken into account when designing in the PLM II module is the Tcase temperature. The Tcase must never exceed Tcase,max tested in a draft-free lab environment at 30 C, with final driver and within the luminaire fixture. Table 6. Thermal rating of the system Item Description Symbol Unit Max value Case temperature Delta T Temperature at which the module operates within specifications The maximum temperature difference between Tambient and Tcase Tcase C 75 ΔT C 45 Operating temperature Definitions Module temperature: temperature measured at the specified Tcase point (at the base) of the module Tcase: Heatsink temperature measured at the middle of the heatsink at specified Tcase Driver temperature: temperature measured at the specified Tcase point on the driver Ambient temperature: temperature of the air surrounding the luminaire in the test environment or application Ambient temperature in a lab environment: air temperature in a testing area, in a controlled environment free from drafts Average ambient temperature: monthly average temperature based on at least 2 measurements per day, with at least 8-hour intervals between measurements 17

20 Module temperature To achieve typical product lifetime characteristics, it is crucial to ensure that the product is operating within the specified temperature limits. These limits are determined not only by the product and the application, but also by the luminaire design and ambient environment. Warning! Maximum Tcase should never exceed specified Tcase max Thermal design should ensure that module Tcase <75 C Thermal design should ensure that driver Tcase < max specified driver Tcase Thermal design must ensure maximum ΔT (Tcase Ta) 45 C Warning! PLM modules in combination with Xitanium Fixed Output drivers don t have temperature protection settings (NTC) to detect overheating and extreme lifetime degradation of the LEDs when operated outside the maximum permitted environmental conditions. Such conditions can be caused by extreme ambient conditions or inadequate heat management design. Optimum performance will only be achieved if the Tcase stays below 75 C at 30 C average ambient temperature, measured according to the procedure described above. Thermal measurements The maximum ambient temperature at which the luminaire will operate constitutes the initial key criterion for defining the correct temperature limit and validating the thermal luminaire design. If the maximum ambient temperature (Tamb,max) is 30 C or lower, the luminaire design needs to ensure that the module temperature does not exceed 75 C when tested in a lab environment at 30 C ambient. Note: The ambient temperatures given above are average temperatures during the operational period of the module. Critical temperature point (Tcase) For LEDs, the junction temperature is the critical factor for operation. Since there is a direct relation between the case temperature and the LED junction temperature, it is sufficient to measure the aluminum casing of the PLM board at its critical temperature point, see Figure 23. If the case temperature at the Tcase point exceeds the recommended Tcase life, this will have an adverse effect on the performance of the LEDs and the PLM module in terms of light output, lifetime and lumen maintenance. 18

21 Measurement of critical temperature point On the back of the module there is a Tcase (Tc) point, which should be used for all temperature measurements. The maximum temperature of the module should be measured at a point in the center of the bottom of the LED board, see Figure 23. The temperature must be stable before any reliable data can be obtained (depending on the size and material of the luminaire, this will take between 30 and 180 minutes). Figure 23. Tc point N.B. It is important that the Tcase point is free of thermal interface material when the thermocouple is connected so that temperature measurements can be taken. It is essential to have a stable connection between the thermocouple and the module. Any shifting of the thermocouple will result in measurement errors and poor measurement repeatability. The Tcase should be measured at its critical temperature point using a thermocouple on the base of the LED module. N.B. In order to ensure accurate Tcase test results, the case temperature should not vary by more than 1 C for a period of at least 30 minutes. 19

22 Recommendations for module clusters in luminaire fixture design CertaFlux PLM II modules are designed for IP66 applications. Clustering of max number of 5 modules is an option. The min distance between the modules is 5mm as specified in CSA standard. A reference luminaire with 4 PLM modules is shown in figure 15. Open slots in top cover have been designed to optimize heat management and minimize enviroemntal polluion (i.e. dirt, dust etc). Figure 24. Frontside of reference luminaire Minimum clearance distance between modules 5mm 5mm Figure 26. Clearance distance between modules Figure 25. Backside of reference luminaire Warning! Clusters of PLM modules in closed luminaires will affect the temperatures and the lifetime performance. Thermal performance should be tested in luminaire fixture with maximum number of modules in wind free environment of Ta 30 C. Enclosed environments of clusters with module distance < 5mm will deviate from lifetime spec. Figure 27. Example of open slots designed on top cover of reference luminaire CertaFlux PLM II modules are equipped with integrated heatsink. However, thermal perfomance of the modules and therefore lifetime performance can be influenced by the three following factors: the number of modules designed in the luminaire, the moutning distance between the modules and the design of the top cover. Figure 27 shows an example of open slots designed on the top cover of a reference luminaire to faciliate heat management. Figures 28 and 29 depict two examples of reference luminaires with slots 1mm and 5mm high respectively designed on the top cover of the luminaire. The modules are designed-in with 5mm distance. Expected temperature rise by means of thermal simulations is estimated to 10 o C for 1mm high open slot and to 5 o C for 5mm high open slot. Therefore it is highly recommended that thermal performance should be tested in luminaire fixture with maximum number of modules in wind free environment of Ta 30 o C. 20

23 Figure 28. Top cover of reference luminaire with 1mm open slot Figure 29. Top cover of reference luminaire with 5mm open slot Xitanium LED driver temperature The next key component is the driver, which influences the lifetime and reliability of the system. It is important to ensure good thermal and electrical contact between the driver and the luminaire as this enables the heat to dissipate efficiently and allows the driver to deliver optimal electrical performance. The driver temperature can be measured with a thermocouple at the Tcase point, shown on the driver label. Please refer to individual product datasheets for Tcase max information. 21

24 Quality Compliance and approval marks The Philips CertaFlux PLM II system is CQC, CB/CE and ENEC approved and complies with the applicable EU directives. To ensure approval of the luminaire, the conditions of acceptance need to be fulfilled. Module-related data can be found in GB24819 and IEC All luminaire manufacturers are advised to conform to the international standards of luminaire design GB and IEC Sustainability CertaFlux PLM II system is compliant with European Directive 2011/65/EU, recasting 2002/95/EC on Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS). The modules comply with Reach, as defined by the EU Chemical Agency. Warranty The warranty on CertaFlux PLM II module performance only applies if the product is used in combination with approved Philips Xitanium LED drivers (Tables 2 to 7). IP rating CertaFlux PLM II system is independent systems and has IP66 classification. They are designed for operation in the open air. The OEM is responsible for proper IP classification and approbation of the luminaire. Photobiological safety The photobiological safety standard IEC (Photobiological safety of lamps and lamp systems) gives guidance on the evaluation of the photobiological safety of lamps and lamp systems, including luminaires. This standard specifies the exposure limits, reference measurement technique and classification scheme. It should be used for the evaluation and control of photobiological hazards from all electrically powered, incoherent broadband sources of optical radiation, including LEDs, in the wavelength range from 200 to 800 nm. 22

25 Table 7. Wavelengths used for photobiological safety measurements Radiance-based Irradiance-based Blue Light LB nm Retinal Thermal LR nm Actinic UV Skin & Eye ES nm Eye UVA EUVA nm Retinal Thermal LIR nm Blue Light Small EB nm Sources Eye IR EIR nm Table 8. PLM II Gen1 photobiological measurement results Item Symbol Result: Risk group Actinic UV Es Exempt Near-UV EUVA Exempt Retinal Blue Light LB RG1 Retinal thermal LR Exempt Infrared eye EIR Exempt EMC Electromagnetic compatibility, EMC, is the ability of a device or system to operate satisfactorily in its electromagnetic environment without causing unacceptable interference in practical situations. To maintain good EMC performance at the luminaire level, the input, output and control wires should be kept as far apart as possible. Addition of ferrite beads in series with the wires, or coupling the wires through ferrite cores within the luminaire may improve the overall EMC performance. However, selection of the type and characteristics of the additional filter depends on what frequency components have to be damped and by how much. In general, LED modules have no effect on the EMC of a luminaire. The PLM II Gen1 was tested with a Xitanium driver in a reference luminaire and no EMC issues were observed. Electrostatic discharge (ESD) Introduction to ESD It is generally recognized that Electro Static Discharge (ESD) can damage electronic components, like LED chips, resulting in early failures. Professional users of electronic components are used to implementing extensive and rigorous measures to prevent ESD damage in their finished products. With the introduction of LED components for lighting, a new breed of users, such as OEMs and installers, are now involved in handling and using electronic LED components in the manufacturing process. 23

26 ESD in the production environment Depending on the immunity level of the LED board, there is a minimum set of measures that have to be implemented when handling LED boards. ESD measures are required in a production environment where handling can exceed the ESD immunity level. Furthermore, products that are susceptible to ESD must be packed and delivered in ESD-safe packaging. The purpose of an effective ESD-control strategy is to reduce line failures, final inspection failures and field failures. ESD specifications Philips designed PLM II Gen1 products to be robust when exposed to ESD. The maximum permitted contact discharge level and air discharge level, according to IEC , is 4 kv contact and 8 kv air. Servicing and installing luminaires It is highly recommended that installers are instructed not to touch the LED components and to use earthed arm straps to prevent ESD damage during installation and maintenance. ESD consultancy Independent ESD consultancy companies can advise and supply adequate tools and protection guidance. Philips Innovation Services can provide consultancy at More information can be found in the Contact details section. Remote system operation Please consult the design-in guide for Xitanium LED drivers. Use of circuit breakers: Xitanium LED drivers Please consult the design-in guide for Xitanium LED drivers at Note on conditions for storage, transportation and operation Store in a dark place Do not expose to sunlight Maintain temperature between -40 and +85 C Relative humidity (RH) between 5% and 90% During operation PLM II Gen1 must be operated within the specifications stated in the product leaflet and design-in guide. Please contact your local sales representative for additional information. 24

27 System disposal We recommend that the PLM II Gen1 and its components are disposed of in an appropriate way at the end of their (economic) lifetime. The modules are in effect normal pieces of electronic equipment containing components that are currently not considered to be harmful to the environment. We therefore recommend that these parts are disposed of as normal electronic waste, in accordance with local regulations. 25

28 Contact details Philips PLM II Gen1 or contact your local Philips sales representative. The following are suggested products for use with the PLM II Gen1 systems. Reference to these products does not constitute endorsement thereof by Philips. Philips makes no warranties regarding these products and assumes no legal liability or responsibility for loss or damage resulting from the use of the information provided here. Philips EMC support The Philips corporate EMC competence center is a leading provider of approbation and consultancy services. Phone: +31- (0) Fax: (0) Thermal management partners Asia Vital Components Co., Ltd The Bergquist Company Laird Technologies