Vibration Transducer SLD121 A

Transcription

1 Vibration Transducer SLD2 A The vibration transducer SLD2 A is a piezo-electric accelerometer of compression type with built-in preamplifier, designed for vibration monitoring of industrial machinery. The electrical signal is isolated from the transducer housing. Min. 25 mm The transducer is mounted against a smooth, flat surface on the machine. Standard thread size is. The transducer is connected via a coaxial cable (SPM 0005-L or 0267-L) with SMB connector. Nominal sensitivity, main axis:.2 mv/m/s 2 * =2 Typical base strain sensitivity: Linear frequency range: Max. peak acceleration: 0.0 m/s 2 /m strain 2 to 000 Hz (±db) 600 m/s 2 = 60 g Bias point: 6 to V (typical 8 V) Power requirements: 40 C to +25 C ( 40 F to 260 F) 2 to 24 V, 2 to 5 ma IP 67 together with connector SPM 5388, 40 or 564 SMB / 40 / Pilot for To drill the mounting hole, use drill bit 6. mm. Torque the transducer with a 24 mm torque wrench k 40k Hz are subject to change without notice. ISO 00 certified. Copyright SPM TD-0. B

2 Vibration Transducer SLD2B / SLD2F PIN A + PIN B t = (SLD2B) UNF /4"(SLD2F) The vibration transducer SLD2 B and SLD2F are piezoelectric accelerometers of compression type with built-in preamplifier, designed for vibration monitoring of industrial machinery. The electrical signal is isolated from the transducer housing. The transducer is mounted against a smooth, flat surface on the machine. SLD2B has thread size and SLD2F has thread size UNF /4". The transducer is connected via a twisted pair cable with 2 pin connector, compatible with 2 pin MIL-C-505 style. Nominal sensitivity, main axis:.2 mv/m/s 2 * =2 Typical base strain sensitivity: 0.0 m/s 2 /µ strain Linear frequency range: 2 to 000 Hz (±db) Max. peak acceleration: 600 m/s 2 = 60 g Bias point: 6 to V (typical 8 V) 40 C to +25 C ( 40 F to 260 F) Power requirements: 2 to 24 V / 2 to 5 ma IP 67 together with appropriate connector Compatible with 2 pin MIL-C-505 style SPM 568 (UNF /4") Pilot for UNF /4" (SLD2F) 803 Pilot for (SLD2B) To drill the mounting hole, use drill bit 6. mm (5.5 for UNF /4"). Torque the transducer with a 24 mm torque wrench k 40k Hz are subject to change without notice. ISO 00 certified. Copyright SPM TD-255. B

3 Vibration Transducer SLD22 A The vibration transducer SLD22 A is a piezo-electric accelerometer of compression type with built-in preamplifier, designed for vibration monitoring of industrial machinery. The electrical signal is isolated from the transducer housing. Min. 25 mm The transducer is mounted against a smooth, flat surface on the machine. Standard thread size is. The transducer is connected via a coaxial cable (SPM 0005-L or 0267-L) with SMB connector. Nominal sensitivity, main axis: 4 mv/m/s 2 * =40 Typical base strain sensitivity: Linear frequency range: Max. peak acceleration: Bias point: Power requirements: 0.0 m/s 2 /µ strain 2 to 5000 Hz (±db) 600 m/s 2 = 60 g 6 to V (typical 8) V 40 C to +25 C ( 40 F to 260 F) 2 to 24 V, 2 to 5 ma IP 67 together with connector SPM 5388, 40 or 564 SMB / 40 / Pilot for To drill the mounting hole, use drill bit 6. mm. Torque the transducer with a 24 mm torque wrench k 0k k Hz are subject to change without notice. ISO 00 certified. Copyright SPM TD-87. B

4 Vibration Transducer SLD22B / SLD22F PIN A + PIN B t = (SLD22B) UNF /4"(SLD22F) The vibration transducer SLD22 B and SLD22F are piezoelectric accelerometers of compression type with built-in preamplifier, designed for vibration monitoring of industrial machinery. The electrical signal is isolated from the transducer housing. The transducer is mounted against a smooth, flat surface on the machine. SLD22B has thread size and SLD22F has thread size UNF /4". The transducer is connected via a twisted pair cable with 2 pin connector, compatible with 2 pin MIL-C-505 style. Nominal sensitivity, main axis: 4 mv/m/s 2 * =40 Typical base strain sensitivity: 0.0 m/s 2 /µ strain Linear frequency range: 2 to 5000 Hz (±db) Max. peak acceleration: 600 m/s 2 = 60 g Bias point: 6 to V (typical 8 V) 40 C to +25 C ( 40 F to 260 F) Power requirements: 2 to 24 V, 2 to 5 ma IP 67 together with appropriate connector Compatible with 2 pin MIL-C-505 style SPM 568 (UNF /4") 8030 Pilot for UNF /4" (SLD22F) 803 Pilot for (SLD22B) To drill the mounting hole, use drill bit 6. mm (5.5 for UNF /4"). Torque the transducer with a 24 mm torque wrench k 0k k Hz are subject to change without notice. ISO 00 certified. Copyright SPM TD-. B

5 Vibration Transducer SLD44B / SLD44F PIN A + PIN B t = (SLD44B) UNF /4"(SLD44F) The vibration transducer SLD44B and SLD44F are piezoelectric accelerometers of compression type with built-in preamplifier, designed for vibration monitoring of industrial machinery. The electrical signal is isolated from the transducer housing. The transducer is mounted against a smooth, flat surface on the machine. SLD44B has thread size and SLD44F has thread size UNF /4". The transducer is connected via a twisted pair cable with 2 pin connector, compatible with 2 pin MIL-C-505 style. Nominal sensitivity, main axis: 0 mv/m/s 2 * =00 Typical base strain sensitivity: 0.0 m/s 2 /µ strain Linear frequency range: 2 Hz - 0 khz (±db ) ( 3 db at 0.7 Hz typ) Max. peak acceleration: 600 m/s 2 = 60 g Bias point: to 3 V (typical 2 V) 40 C to +25 C ( 40 F to 260 F) Power requirements: 24 V /2 to 5 ma IP 67 together with appropriate connector Compatible with 2 pin MIL-C-505 style SPM 568 (UNF /4") 8030 Pilot for UNF /4" (SLD44F) 803 Pilot for (SLD44B) 40 To drill the mounting hole, use drill bit 6. mm for and 5.5 mm for UNF/4". Torque the transducer with a 24 mm torque wrench k 40k Hz are subject to change without notice. ISO 00 certified. Copyright SPM TD-3. B

6 Vibration Transducer TRV-8 / Measuring direction 7 ø Cable clamp t ø 5 TRV-8: t = TRV-: t = UNF /4"- 28 The transducers TRV-8 and TRV- are piezo-electric accelerometers of compression type with built-in preamplifier, designed for vibration monitoring of industrial machinery. They are used in permanent installations with the CMM System and MG-4. The cable length between transducer and measuring unit is max. 50m (65 ft). The transducer is mounted against a smooth, flat surface on the machine. TRV-8 has thread size and TRV- has UNF /4"-28. The transducers are delivered with three washers for adjusting the connector angle. Each washer turns the transducer 0ϒ. The coaxial cable (SPM 0005-L or 0267-L) with TNC connector must be secured with a clamp close to the transducer. In moist environments, use sealing TNC cable plugs SPM 3008 to prevent cable corrosion. For electric insulation, use insulation foot TRX-8 / TRX-. Electric insulation: TRX-8 () TRX- (UNF) Moist environment: SPM 3008 Nominal sensitivity, main axis:.2 mv/m/s 2 * Typical base strain sensitivity: 0.0 m/s 2 / strain Linear frequency range: 3 to 000 Hz Max. peak acceleration: 600 m/s 2 -ϒ C to +25ϒ C (-4ϒ F to +260ϒ F) Typical temperature drift: 0.25% / ϒC Housing, base:, Sandvik Grade:802, EN:.4523 Design: Sealed Connector tightness: IP65 with TNC connector IP67 with conn. SPM grams (5 oz) TNC 0 Nm (7.4 lbf/ft) Power requirement: 2 to 24 V DC Constant current: 2 to 5 ma Bias point: 5 to V (typ 7 V) 8030 Pilot for UNF /4"-28 (TRV-) 803 Pilot for (TRV-8) (UNF /4"-28) To drill the mounting hole, use drill bit 6. mm for and 5.5 mm for UNF /4"-28. Torque and unscrew the transducer with a torque wrench and a 7 mm socket (SPM 8086). are subject to change without notice. ISO 00 certified. Copyright SPM TD-0 B

7 Vibration Transducer TRV-/2 Measuring direction 7 36 ø 27.5 Cable clamp t ø5 The transducers TRV- and TRV-2 are piezo-electric accelerometers of compression type with built-in preamplifier, designed for vibration monitoring of industrial machinery. The transducers are used in permanent installations with the CMS System (measuring unit VCM) and with the hand-held instrument Leonova. The cable length between the transducer and the measuring unit is max. 50 m (65 ft). The transducer is mounted against a smooth, flat surface on the machine. TRV- has thread size and TRV-2 has UNF /4"-28. The transducers are delivered with three washers for adjusting the connector angle. Each washer turns the transducer 0. The coaxial cable (SPM 0005-L or 0267-L) with TNC connector must be secured with a clamp close to the transducer. In moist environments, use sealing TNC cable plugs SPM 3008 to prevent cable corrosion. For electric insulation, use insulated installation foot TRX-8/. Electric insulation: TRX-8 () TRX- (UNF) Typical frequency response Typical thermal response Moist environment: SPM 3008 Nominal sensitivity, main axis: 4.0 mv/m/s 2 * Typical base strain sensitivity: 0.0 m/s 2 /µ strain Linear frequency range: 2 to 5000 Hz Max. peak acceleration: 600 m/s 2 - C to +25 C (-4 F to +260 F) Power requirements: 2 24 V, 2 5 ma, Sandvik Grade:802, EN:.4523 Design: Sealed Connector tightness IP65 with TNC connector IP 67 with conn. SPM grams (5 oz) TNC 0 Nm (7.4 lbf ft) Bias point: 6 to 2 V (typ 8 V) (UNF /2"-28) 8030 Pilot for UNF /4" (TRV-2) 803 Pilot for (TRV-) To drill the mounting hole, use drill bit 6. mm for and 5.5 mm for UNF /4". Torque and unscrew the transducer with a torque wrench and a 7 mm socket (SPM 8086). are subject to change without notice. ISO 00 certified. Copyright SPM TD-24 B

8 Vibration Transducer TRV-22 / 23 Measuring direction 7 ø Cable clamp t ø 5 TRV-22: t = TRV-23: t = UNF /4"- 28 The transducers TRV-22 and TRV-23 are piezo-electric accelerometers of compression type, designed for vibration monitoring of industrial machinery. They can be used together with handheld instruments or in permanent installations. Max. cable length between transducer and measuring unit is 0 m (33 ft). The transducer is mounted in a threaded hole on a smooth, flat surface on the machine. It is delivered with three washers for adjusting the connector angle. Each washer turns the transducer 0ϒ. Fix low noise coaxial cable (SPM 076-L or 022-L) with TNC connector with a clamp close to the transducer. For installations in moist environments, use sealing TNC cable plugs SPM 3008 to prevent cable corrosion. Installation in moist environments SPM 3008 Nominal sensitivity, main axis: 0 pc/m/s 2 (7-2 pc/m/s 2 ) * Typical base strain sensitivity: 0.0 m/s 2 / strain Linear frequency range: 0 to 5000 Hz Max. peak acceleration: 600 m/s 2 30ϒ C to +50ϒ C ( 22ϒ F to +302ϒ F) Typical temperature drift: 0.25% / ϒC Housing, base:, Sandvik Grade:802, EN:.4523 Design: Sealed Connector tightness: IP65 with TNC connector IP67 with conn. SPM grams (6 oz) TNC 0 Nm (7.4 lbf/ ft) (UNF /4"-28) To drill the mounting hole, use drill bit 6. mm () or 5.5 mm (UNF /4"-28). Torque and unscrew the transducer with a torque wrench and a 7 mm socket (SPM 8086). Part Numbers TRV-22 Vibration transducer, TRV-23 Vibration transducer, UNF /4" Sealing TNC cable plug 8057 Counterbore, diam. mm 8030 Pilot for UNF /4" (TRV-23) 803 Pilot for (TRV-22) Tel Fax info@spminstrument.se are subject to change without notice. ISO 00 certified. Copyright SPM TD-33.B