1 XS3W-M R Robot cable

Transcription

1 Round Water-resistant Connectors (M8/S8) XS Small Round Water-resistive Connectors Water-resistive, compact connector meets IP67 requirements. Conventional M8 screw-on models are available along with S8 snap-in models that connect and disconnect with one touch. Ideal for a wide variety of FA and OA applications. Connectors on both cable ends require no harness work. Some new M8 models with or poles. Oil-resistant Polyurethane Robot Cables added. M8-M conversion cables are also available. Refer to Safety Precautions on page. Model Number egend Connectors with Cables Model Number egend Connector Cable specifications XS: M8 screw connection Cable length (m) Model Reference page XSW-M-0-R Robot cable XSW-M-0-R XSW-M-0-R Connectors on both cable ends XSW-M-0-PR Oil-resistant (PUR) robot XSW-M-0-PR cable XSW-M-0-PR XSF-M-0-A Standard cable XSF-M-0-A 0 XSF-M-0-A XSF-M-0-R XSF-M-0-R Connector on one cable end Robot cable XSF-M-0-R (Socket) 0 XSF-M-0-R 9 Oil-resistant (PUR) robot XSF-M-0-PR cable XSF-M-0-PR PUR (low-temperature use) XSF-M-0- cable XSF-M-0-0. XSH-M-C-R Robot cable Connector on one cable end XSH-M-0-R (Plug) Oil-resistant (PUR) robot XSH-M-0-PR cable XSH-M-0-PR Note: Only DC, straight, and -core types are shown in this table. Refer to the relevant pages for other products.

2 Ratings and Specifications XS Item Model XSF/H/W/P/M XSR Rated current ADC ADC ADC Rated voltage VDC * 0 VDC VDC Contact resistance (connector) Insulation resistance Dielectric strength (connector) Degree of protection Insertion tolerance Cable tensile strength * Ambient operating temperature range Ambient humidity range *. Models with cable only *. Except poles *. Use the robot cable within a temperature range between 0 C and 70 C to prevent the wires inside the cable from being broken when bending it. Materials and Finish Connector Cables 0 m max. (0 mv max., 00mA max.),000 M min. (at 00 VDC),000 VAC for min (leakage current: ma max.) IP67 (IEC609) 00 times 9 N/ s Note: Only the XSF (socket) is available with poles. Pin Arrangement (Engaged Side) 60 VAC for min (leakage current: ma max.) 60 m max. (0 mv max., 00 ma max.),000 VAC for min (leakage current: ma max.) to 70 C * to 8 C to 70 C 0 to 8%RH Type M8 S8 Item Model XSF/H/W/R XSP/M * XSM-M-@ XSF/W (Socket side) XSH/W (Plug side) XSP Contact block PBT resin (U9 V-0) light gray or black Contacts Phosphor bronze/nickel Brass/nickel base, Phosphor bronze/nickel Brass/nickel base, base, 0.-μm gold plating 0.-μm gold plating base, 0.-μm gold plating 0.-μm gold plating Fixture Brass/nickel plating or SUS6 Brass/nickel plating Body Brass/ Nickel-plated zinc nickel plating alloy Shell TPEE C-Ring Phosphor bronze/ tin plating Grounding fixture Phosphor bronze/ tin plating Nut Brass/nickel plating Brass/nickel plating Cover Soft PBT resin (U9V-0) TPEE O-ring Rubber *Except poles Note: The XSM is for both M8 and S8. Item Poles poles poles poles mm dia, AWG (0. mm Standard cable ).7 mm dia, AWG (0. mm ) Structure: 0. mm/8 Structure: 0.6 mm/ mm dia, AWG (0. mm Robot Cable ) Structure: 0.08 mm/0 Oil-resistant polyurethane robot cable Item Poles poles poles poles.7 mm dia, AWG (0. mm ) Structure: 0.08 mm/60 DC Male (plug) contacts Female (socket) contacts

3 XS XSW Connectors with Cables, Connectors on Both Cable Ends (Socket/Plug) Model Number egend Use this model number legend to identify products from their model number. Use this model number legend to identify products from their model number. When ordering, use a model number from the table in Ordering Information. XSW-@@@-@@@-@ 6. Fastening Method M: M8 S: S8. Connector Poles : poles : poles. Cable Connection Direction : Straight/Straight : Right-angle/Right-angle : Straight (socket)/ Right-angle (plug) : Right-angle (socket)/ Straight (plug). Connections ➀ ➂ ➃ : Brown Blue Black ➀ ➁ ➂ ➃ : Brown White Blue Black. Cable ength 0: m 0: m 0: m 6. Cable Specifications R: Vibration-proof robot cable PR: Oil-resistant polyurethane robot cable Ordering Information M8 Screw-on Connectors Cable specifications No. of cable cores Cable connection direction Cable length (m) Model Vibration-proof robot cable Oil-resistant polyurethane robot cable Straight/Straight Straight/Straight Right-angle/Right-angle Straight (Socket)/Right-angled (Plug) Right-angle (socket)/straight (plug) Straight/Straight Right-angle/Right-angle Straight (Socket)/Right-angled (Plug) Right-angle (socket)/straight (plug) XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-R XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR XSW-M-0-PR

4 XS S8 Snap-in Connectors Cable specifications No. of cable cores Cable connection direction Cable length (m) Model Vibration-proof robot cable Note: Ask your OMRON representative about other cable lengths. Straight/Straight Right-angle/Right-angle Straight (Socket)/Right-angled (Plug) Right-angle (socket)/straight (plug) XSW-S-0-R XSW-S-0-R XSW-S-0-R XSW-S-0-R XSW-S-0-R XSW-S-0-R XSW-S-0-R XSW-S-0-R XSW-S-0-R Wiring Diagram/Engaged Side poles Cable lead colors Brown Blue Black poles Socket Plug Cable lead colors Brown White Blue Black Socket Plug Mating Connectors Model Socket side Plug side XSW (M8) XSW (S8) XSM (M8/S8) XSH (M8) XSM (M8/S8) XSH (S8) XSF (M8) XSW (M8) XSP (M8) XSF (S8) XSW (S8) XSP (S8) Note. Cables can be extended with more than one XSW.. M8 screw models and S8 snap-in models cannot be connected to each other.

5 Dimensions XS (Unit: mm) M8 Screw-on Connectors with Vibration-proof Robot Cable Straight/Straight Connectors (-core) (-core) Straight (Socket)/Right-angle (Plug) Connectors (-core) M8.0 0 dia. Socket dia. Plug M8.0 dia.. 0 dia.... Right-angle/Right-angle Connectors XSW-M-@@-R (-core) Right-angle (Socket)/Straight (Plug) Connectors XSW-M-@@-R (-core) M8.0 0 dia. 0. dia.. 0. dia. M8.0 0 dia.... M8 Screw-on Connectors with Oil-resistant Polyurethane Robot Cable Straight/Straight Connectors XSW-M-@@-PR (-core) M8 Molded part (black).7 dia. Straight (Socket)/Right-angle (Plug) Connectors XSW-M-@@-PR (-core) M8 Molded part (black).7 dia. 0 dia. 0 dia Right-angle/Right-angle Connectors XSW-M-@@-PR (-core) Right-angle (Socket)/Straight (Plug) Connectors XSW-M-@@-PR (-core) Molded part (black) 0 dia..7 dia. 0 dia. M8 Molded part (black).7 dia.. M

6 XS S8 pin Snap-in Connectors with Vibration-proof Robot Cable Straight/Straight Connectors Socket dia. Plug Straight (Socket)/Right-angle (Plug) Connectors dia. 8. dia dia. 8. dia. 8. dia Right-angle/Right-angle Connectors 8. dia. 8. dia. Right-angle/Straight Connectors 8. dia. dia. dia dia

7 XS XSW Connectors with Cables, Connectors on Both Cable Ends (M8 Socket/M Plug or M8 Plug/M Socket) Model Number egend Use this model number legend to identify products from their model number. Use this model number legend to identify products from their model number. When ordering, use a model number from the table in Ordering Information. XSW-M@@-@C-A 6. Fastening Method M: M8. Connector Poles : poles : poles. Cable Connection Direction C: M8 (screw-on) socket: Straight, M (Smartclick) plug: Straight D: M8 (screw-on) plug: Straight, M (Smartclick) socket: Straight. Connections ➀ ➂ ➃ : Brown Blue Black ➀ ➁ ➂ ➃ : Brown White Blue Black. Cable ength C: 0 cm 6. Cable Specifications A: Standard cable Ordering Information Cable specifications No. of cable cores Connectors Cable length (m) Model M8 socket/m plug XSW-MC-C-A M8 plug/m socket XSW-MD-C-A Standard cable 0. M8 socket/m plug XSW-MC-C-A M8 plug/m socket XSW-MD-C-A Wiring Diagram poles poles Cable lead colors Cable lead colors Brown Blue Black Brown White Blue Black 7

8 XS Dimensions (Unit: mm) Screw-on Connectors (M8 to M) XSW-MC-C-A XSW-MC-C-A ( cores). M.0 Plug dia. Socket M8.0 ( cores) M8.0 Smartclick Connectors (M8-M) XSW-MD-C-A XSW-MD-C-A ( cores). 0 dia. M.0 Socket dia. Plug M8.0 ( cores) M8.0 Note: For -core, M connectors, pin is not connected internally. XS Series Click! Insert fully. Rotate /8 turn. One-touch Connection 8

9 XS XSF Connectors with Cables, Sockets on One Cable End Model Number egend Use this model number legend to identify products from their model number. When ordering, use a model number from the table in Ordering Information. XSF-@@@-@@@-@ 6. Fastening Method M: M8 S: S8 E: M8 SUS6 ock. Connector Poles : poles : poles : poles. Cable Connection Direction : Straight : Right-angle. Connections ➀ ➂ ➃ : Brown Blue Black ➀ ➁ ➂ ➃ : Brown White Blue Black ➀ ➁ ➂ ➃ ➄ : Brown White Blue Black Gray. Cable ength 0: m 0: m 0: m 0: 0 m 6. Cable Specifications A: Standard cable : PUR cable (low-temperature use) R: Vibration-proof robot cable PR: Oil-resistant polyurethane robot cable 9

10 XS Ordering Information M8 Screw-on Connectors Cable specifications No. of cable cores Cable connection direction Cable length (m) Model Standard cable Vibration-proof robot cable Standard cable Standard SUS6 cable lock Vibration-proof robot cable Oil-resistant polyurethane robot cable PUR cable (low-temperature use) Standard cable S8 Snap-in Connectors Note: Ask your OMRON representative about other cable lengths. Straight Right-angle Straight Right-angle Straight Right-angle Straight Right-angle Straight Right-angle Straight Right-angle Straight Right-angle Straight Right-angle XSF-M-0-A XSF-M-0-A XSF-M-0-A XSF-M-0-A XSF-M-0-R XSF-M-0-R XSF-M-0-R 0 XSF-M-0-R XSF-M-0-R XSF-M-0-R XSF-M-0-A XSF-M-0-A 0 XSF-M-0-A XSF-M-0-A XSF-M-0-A 0 XSF-M-0-A XSF-E-0-A XSF-E-0-A XSF-E-0-A XSF-E-0-A XSF-M-0-R XSF-M-0-R XSF-M-0-R 0 XSF-M-0-R XSF-M-0-R XSF-M-0-R XSF-M-0-R 0 XSF-M-0-R XSF-M-0-PR XSF-M-0-PR XSF-M-0-PR XSF-M-0-PR XSF-M-0-PR XSF-M-0- XSF-M-0- XSF-M-0- XSF-M-0- XSF-M-0-A XSF-M-0-A 0 XSF-M-0-A XSF-M-0-A XSF-M-0-A 0 XSF-M-0-A Cable specifications No. of cable cores Cable connection direction Cable length (m) Model Vibration-proof robot cable Straight Right-angle XSF-S-0-R XSF-S-0-R XSF-S-0-R XSF-S-0-R XSF-S-0-R XSF-S-0-R 0

11 Mating Connectors XS Model Mating Connectors XSF (M8) XSM (M8/S8), XSH (M8), XSW (M8) XSF (S8) XSM (M8/S8), XSH (S8), XSW (S8) Note: M8 screw models and S8 snap-in models cannot be connected to each other. Dimensions (Unit: mm) M8 Screw-on Connectors (-core) Straight Connectors Vibration-proof robot cable Standard cable M8.0 dia Right-angle Connectors XSF-M-@@-A Vibration-proof robot cable XSF-M-@@-R Standard cable. 0 dia M8.0 Wiring Diagram Cable lead colors Brown Blue Black M8 Screw-on Connectors (-core) Straight Connectors XSF-M-@@-A Vibration-proof robot cable XSF-M-@@-R Standard cable. M8.0.9 dia Right-angle Connectors XSF-M-@@-A Vibration-proof robot cable XSF-M-@@-R Standard cable dia M8.0.9 Wiring Diagram Cable lead colors Brown White Blue Black

12 XS M8 SUS6 ock (-core) Straight Connectors XSF-E-0-A XSF-E-0-A. M8.0.9 dia Right-angle Connectors XSF-E-0-A XSF-E-0-A dia.. M Wiring Diagram Cable lead colors Brown White Blue Black M8 Screw-on Connectors (-core) Straight Connectors Oil-resistant polyurethane robot cable XSF-M-@@-PR PUR cable XSF-M-@@-..7 dia. M8 0 Right-angle Connectors Oil-resistant polyurethane robot cable XSF-M-@@-PR PUR cable XSF-M-@@-.9.7 dia. 0. Molded part (black) 0 M Wiring Diagram Cable lead colors Brown White Blue Black

13 XS M8 Screw-on Connectors (-core) Oil-resistant Standard Cable Straight Connectors M8.0.7 dia Right-angle Connectors XSF-M-@@-A.9.7 dia M Wiring Diagram Cable lead colors Brown White Blue Black Gray S8 pin Snap-in Connectors with Vibration-proof Robot Cable Straight Connectors XSF-S-@@-R. 8. dia..9 dia Right-angle Connectors XSF-S-@@-R dia.. 8. dia Wiring Diagram Cable lead colors Brown White Blue Black

14 XS XSH Plugs on One Cable End Model Number egend Use this model number legend to identify products from their model number. When ordering, use a model number from the table in Ordering Information. XSH-@@@-@@@-@ 6. Fastening Method M: M8 S: S8. Connector Poles : poles : poles. Cable Connection Direction : Straight : Right-angle. Connections ➀ ➂ ➃ : Brown Blue Black ➀ ➁ ➂ ➃ : Brown White Blue Black. Cable ength C: 0. m 0: m 0: m 0: m 6. Cable Specifications R: Vibration-proof robot cable PR: Oil-resistant polyurethane robot cable Ordering Information M8 Screw-on Connectors Cable specifications No. of cable cores Cable connection direction Cable length (m) Model Vibration-proof robot cable Oil-resistant polyurethane robot cable Note: Ask your OMRON representative about other cable lengths. S8 Snap-in Connectors Straight Straight Right-angle Straight Right-angle 0. XSH-M-C-R XSH-M-0-R 0. XSH-M-C-R XSH-M-0-R 0. XSH-M-C-R XSH-M-0-R XSH-M-0-PR XSH-M-0-PR XSH-M-0-PR XSH-M-0-PR XSH-M-0-PR Cable specifications No. of cable cores Cable connection direction Cable length (m) Model Vibration-proof robot cable Straight Right-angle 0. XSH-S-C-R XSH-S-0-R 0. XSH-S-C-R XSH-S-0-R Mating Connectors Model Mating Connectors XSH (M8) XSF (M8), XSW (M8), XSP (M8) XSH (S8) XSF (S8), XSW (S8), XSP (S8) Note: M8 screw models and S8 snap-in models cannot be connected to each other.

15 XS Dimensions (Unit: mm) M8 pin Screw-on Connectors with Vibration-proof Robot Cable Straight Connectors M8.0 dia dia Wiring Diagram Cable lead colors Brown Blue Black M8 pin Screw-on Connectors with Vibration-proof Robot Cable Straight Connectors XSH-M-@@-R Four, dia.. M8.0.9 dia. 0 dia Right-angle Connectors XSH-M-@@-R dia. M8.0 Four, dia. 0 dia.. Wiring Diagram Cable lead colors Brown White Blue Black

16 XS M8 pin Screw-on Connectors with Oil-resistant Polyurethane Robot Cable Straight Connectors Four, dia. M8.0.7 dia dia. 0 Right-angle Connectors XSH-M-@@-PR.9.7 dia.. 0 dia. Molded part (black) M8 0 Four, dia Wiring Diagram Cable lead colors Brown White Blue Black S8 pin Snap-in Connectors with Vibration-proof Robot Cable Straight Connectors XSH-S-@@-R Four, dia...9 dia. 8. dia Right-angle Connectors XSH-S-@@-R dia. 8. dia. Four, dia Wiring Diagram Cable lead colors Brown White Blue Black 6

17 XS XSP Panel-mounting Sockets for Terminal Boxes Ordering Information Connection method Panel mounting Pin shape Applicable wires Model DIP pins XSP-M- Front lock or rear lock M8 screw-on Solder cup pins AWG max. XSP-M- Rear lock Solder cup pins AWG max. XSP-M- DIP pins XSP-S- S8 snap-in Front lock or rear lock Solder cup pins AWG max. XSP-S- Note: Orders are accepted in multiples of the minimum order. Mating Connectors Model Mating Connectors XSP (M8) XSH (M8), XSW (M8) XSP (S8) XSH (S8), XSW (S8) Note: M8 screw models and S8 snap-in models cannot be connected to each other. Dimensions (Unit: mm) M8 Screw-on Connectors XSP-M- (DIP Pins) Front lock or rear lock XSP-M- (Solder Cup Pins) Front lock or rear lock.8.9 Four, dia dia dia.. 9. M.0 M.0.. M.0 nut Rubber bushing. 9.7 M8.0 8 dia.. 9. Solder cup hole 0.8 dia.. M.0. M.0 nut M.0. Rubber bushing. 9.7 M8.0 XSP-M- (Solder Cup Pins), Rear ock Slim Models 0 7. (0.) dia. M8 0. M8 0. nut Rubber bushing. 0 M8.0 7

18 XS S8 Snap-in Connectors XSP-S- (DIP Pins) Front lock or rear lock XSP-S- (Solder Cup Pins) Front lock or rear lock Four, dia dia dia.. 9. M.0 M.0.. M.0 nut Rubber bushing dia.. 9. Solder cap hole 0.8 dia.. M.0. M.0 nut M.0. Rubber bushing. 9. Mounting Dimensions for XSP Screw-on Models and Snap-in Models (Unit: mm) Panel Cutout XSP-@-@ XSP-M- PCB-mounting Dimensions and min.. Panel-mounting Dimensions Rear lock Panel Front ock Panel dia. min. Note: The panel thickness is to mm Four,. dia Note: The panel thickness is. mm maximum. Nut Rubber bushing Rubber bushing Nut Safety Precautions Refer to Safety Precautions on page. Precautions for Correct Use Panel-Mounting When mounting XSP Panel-mounting Connectors to panels, refer to Panel-mounting Dimensions and provide rubber bushings and nuts for the Connectors. Apply a tightening torque of between 0. and 0.6 N m to mount the Connectors. 8

19 XS XSM Sensor-Embedded Plugs Ordering Information Mounting method Pin shape Applicable wires Model DIP pins XSM-K- Embedded model Solder cup pins AWG6 max. XSM-K- Mating Connectors Model Mating Connectors XSM XSF (M8/S8), XSW (M8/S8) Note: The plug can be connected to both M8 screw and S8 snap-in models. Dimensions (Unit: mm) Embedded Plug with Screw Threads DIP Pins XSM-K- Four, dia. M8.0 dia. 0.. Four, dia. Mounting 6. dia..8±0. dia..8 dia. 6. dia dia. Solder Cup Pins XSM-K- Four, dia..6 dia M dia Four, dia. Resin filled 7. (min) Mounting 6. dia..8±0. dia..8 dia. 6. dia dia..6 dia. Solder cup hole 0.7 dia Resin filled. (min) 9

20 XS XSM Panel-mounting Plugs Ordering Information Mounting method Pin shape Shield pin Applicable wires Model Front ock Mating Connectors DIP pins. mm (for either round holes or solder cups) No Yes AWG6 max. XSM-M-0 XSM-M- Model Mating Connectors Dimensions (Unit: mm) Front lock ( pins) DIP Pins. mm (for Either Round Holes or Solder Cups), Without Shield Pin XSM-M-0 Panel Cutout PCB-mounting Dimensions 8. mm dia Five,.7 dia. lands Five,. dia SW7 SW0.9 O-ring on panel side* Note: The panel thickness is 0.8 to mm. O-ring on panel side* M8.0 - dia min (.) Panel location (example for t =.0) Note: The panel thickness is. mm maximum DIP Pins. mm (for Either Round Holes or Solder Cups), With Shield Pin XSM-M- Panel Cutout PCB-mounting Dimensions SW 0..9 Pin Numbers *The O-ring on the panel side maintains a waterproof structure (IP67) between the panel and Connector. 8. mm dia Five,.7 dia. lands Five,. dia Two,. lands R0.6 -R0. Two,.8 lands..9 O-ring on panel side* Note: The panel thickness is 0.8 to mm. O-ring on panel side* M Two,. -0. lands Note: The panel thickness is. mm maximum Pin Numbers. - dia SW7 SW min. 7.0 (.) Panel location (example for t =.0) SW *The O-ring on the panel side maintains a waterproof structure (IP67) between the panel and Connector. 0

21 XS Safety Precautions Refer to Safety Precautions on page. Precautions for Correct Use Connection To mate the Connectors, align the mating marks on the Plug and Socket (see following figure), insert the Connectors completely, and tighten the lock nut, being careful not to damage the threads. Panel Mounting After you mount the Connector to the panel, attach the nut and tighten it to a suitable torque (0. N m). Plug Mating marks Socket

22 XS XSR Y-Joint Plug/Socket Connectors Ordering Information Mating Connectors For M8 Connectors Cable With cable Without cable Connector Connectors on both cable ends Connector on one cable end Connectors on both cable ends Cable length Model (m) 0. XSR-M6-C-A XSR-M6-0-A XSR-M6-0-A XSR-M6-0-A XSR-M6-00-A XSR-M6-00-A XSR-M XSR-M6- Model XSR (M8) Mating Connectors XSF (M8) XSH (M8) XSW (M8) XSP (M8) Dimensions (Unit: mm) M8 Screw-on Connectors Connectors on Both Cable Ends (Y-Joint Plug/Socket) 0. M8.0 Socket CN. CN 6. Connector on One Cable End (Y-Joint Plug/Socket) dia..6 dia. dia. Plug 0 dia. CN0 M M8.0. Socket CN CN 6. Connector on Both Ends (Y-Joint Plug/Socket) without Cable XSR-M6-@ 0. M8.0 Socket CN CN. dia. 6.. dia dia. Plug. 0 dia. CN0 dia. 0 0 M8.0 Wiring Diagram XSR-M6-@@-A XSR-M6-@@0-A XSR-M6- XSR-M6- CN CN CN0 CN CN ead color Black Blue White Brown CN CN CN CN0 CN CN0

23 XS XS M8/S8 Connector Cover Dust Covers XSZ- XSZ- M8 Plug XSZ- XSZ- M8 Socket S8 Socket S8 Plug The Dust Cover is for dust prevention and does not ensure IP67 degree of protection. When mounting the Dust Cover to a Connector, be sure to press the Dust Cover onto the Connector until the Connector is fully inserted into the Dust Cover. Model Material Suitable connector Model Mounting portion XSH/XSW/XSR M8 plug XSZ- XSF/XSW S8 socket PVC resin/red XSH/XSW S8 plug XSM M8/S8 plug XSZ- XSF/XSW/XSR M8 socket

24 XS Safety Precautions Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. Connections The XS and XS Sensor I/O Connectors cannot be connected to each other. You cannot mate Connectors that have a different number of poles. When using Sensors with Connectors or imit Switches, use the Sensor I/O Connectors specified in the catalog. Do not connect M8 screw-on models and S8 snap-in models together, otherwise the proper degree of protection of the Connectors will not be maintained. Connector Connection and Disconnection Before connecting or disconnecting Connectors, make sure that no power is being supplied to the Connectors. When connecting or disconnecting Connectors, be sure to hold the Connectors by hand. Do not disconnect the Connectors by pulling the cable. Do not touch the mating surface of the connectors with wet hands. If there is any water on the Connector or near the Connector, be sure to wipe off the water before connecting or disconnecting the Connector, otherwise the Connector may short-circuit internally or not ensure good insulation. Make sure that mating section of any Connector is free of metal dust or power. Do not use pliers to tighten mounting the thread bracket, otherwise the thread bracket may be damaged. Be sure to tighten each thread bracket by hand within a torque of 0. N m. If the thread bracket is not tightened securely, the Connector may not maintain its proper degree of protection or the thread bracket may fall off due to vibration. When you tighten or loosen a thread bracket, hold onto only the thread bracket. If you hold onto the cover or cable, excessive rotational force will be applied to the Connector and may damage it. Fully insert S8 snap-in models until the Connectors are hidden by the metal casing of the opposite parts, otherwise the Connectors will not maintain their proper degree of protection or the thread brackets may become loose due to vibration. Degree of Protection Do not impose external force continuously on the joints of pin blocks and covers, otherwise the Connectors may not keep its proper degree of protection (i.e., IP67). Connectors are not fully watertight. Do not use them underwater. The Connectors are not oil-resistant. Do not use them where they would be subject to oil. If Connectors are used in places with vibration or shock, secure the mating section of each Connector, otherwise the Connectors may be disconnected or fail to maintain their proper degree of protection. Connectors are of resin mold construction. Do not impose excessive force on them. Storage Do not store Connectors for long periods of time in the following locations ocations subject to dust or high humidity ocations subject to ammonia gas or sulfide gas Setup Do not make any cable bends near the base of the Unit. Any bends made must have a minimum radius of 6 mm.

25 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) imitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPIED, ABOUT NON-INFRINGEMENT, MERCHANTABIITY OR FITNESS FOR A PARTICUAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWEDGES THAT IT AONE HAS DETERMINED THAT THE PRODUCTS WI SUITABY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron s sole obligation hereunder shall be, at Omron s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See or contact your Omron representative for published information. imitation on iability; Etc. OMRON COMPANIES SHA NOT BE IABE FOR SPECIA, INDIRECT, INCIDENTA, OR CONSEQUENTIA DAMAGES, OSS OF PROFITS OR PRODUCTION OR COMMERCIA OSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CAIM IS BASED IN CONTRACT, WARRANTY, NEGIGENCE OR STRICT IABIITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer s application or use of the Product. At Buyer s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPICATION INVOVING SERIOUS RISK TO IFE OR PROPERTY OR IN ARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERY RATED AND INSTAED FOR THE INTENDED USE WITHIN THE OVERA EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron s Warranty and imitations of iability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. OMRON Corporation Industrial Automation Company In the interest of product improvement, specifications are subject to change without notice. (c)copyright OMRON Corporation 08 All Right Reserved.