System wide configuration file is "C:\Program Files (x86)\arduino\hardware\mightycore\avr/avrdude.conf"

Transcription

1 C:\Program Files (x86)\arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\arduino\hardware\mightycore\avr/avrdude.conf -v -patmega1284p -cstk500v1 - PCOM5 -b e -Ulock:w:0x3f:m -Uefuse:w:0xfd:m -Uhfuse:w:0xde:m - Ulfuse:w:0xf7:m avrdude: Version 6.0.1, compiled on Apr at 19:59:58 Copyright (c) Brian Dean, Copyright (c) Joerg Wunsch System wide configuration file is "C:\Program Files (x86)\arduino\hardware\mightycore\avr/avrdude.conf" Using Port : COM5 Using Programmer : stk500v1 Overriding Baud Rate : AVR Part : ATmega1284P Chip Erase delay : us PAGEL : PD7 BS2 : PA0 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack eeprom no xff 0xff flash yes xff 0xff lock no x00 0x00 lfuse no x00 0x00 hfuse no x00 0x00 efuse no x00 0x00 signature no x00 0x00 calibration no x00 0x00 Programmer Type : STK500

2 Description : Atmel STK500 Version 1.x firmware Hardware Version: 2 Firmware Version: 1.18 Topcard : Unknown Vtarget : 0.0 V Varef : 0.0 V Oscillator : Off SCK period : 0.1 us avrdude: AVR device initialized and ready to accept instructions Reading ################################################## 100% 0.02s avrdude: Device signature = 0x1e9705 avrdude: erasing chip avrdude: reading input file "0x3f" avrdude: writing lock (1 bytes): C:\Program Files (x86)\arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\arduino\hardware\mightycore\avr/avrdude.conf -v -patmega1284p -cstk500v1 - PCOM5 -b Uflash:w:C:\Program Files ega1284p_16mhz.hex:i -Ulock:w:0x0f:m avrdude: Version 6.0.1, compiled on Apr at 19:59:58 Copyright (c) Brian Dean, Copyright (c) Joerg Wunsch System wide configuration file is "C:\Program Files (x86)\arduino\hardware\mightycore\avr/avrdude.conf" Using Port : COM5 Using Programmer : stk500v1 Overriding Baud Rate : avrdude: 1 bytes of lock written avrdude: verifying lock memory against 0x3f: avrdude: load data lock data from input file 0x3f: avrdude: input file 0x3f contains 1 bytes avrdude: reading on-chip lock data: Reading ################################################## 100% -0.00s avrdude: 1 bytes of lock verified

3 avrdude: reading input file "0xfd" avrdude: writing efuse (1 bytes): Writing ################################################## 100% 0.02s avrdude: 1 bytes of efuse written avrdude: verifying efuse memory against 0xfd: avrdude: load data efuse data from input file 0xfd: avrdude: input file 0xfd contains 1 bytes avrdude: reading on-chip efuse data: avrdude: 1 bytes of efuse verified avrdude: reading input file "0xde" avrdude: writing hfuse (1 bytes): avrdude: 1 bytes of hfuse written avrdude: verifying hfuse memory against 0xde: avrdude: load data hfuse data from input file 0xde: avrdude: input file 0xde contains 1 bytes avrdude: reading on-chip hfuse data: avrdude: 1 bytes of hfuse verified avrdude: reading input file "0xf7" avrdude: writing lfuse (1 bytes): avrdude: 1 bytes of lfuse written avrdude: verifying lfuse memory against 0xf7: avrdude: load data lfuse data from input file 0xf7: avrdude: input file 0xf7 contains 1 bytes avrdude: reading on-chip lfuse data: avrdude: 1 bytes of lfuse verified

4 avrdude done. Thank you. AVR Part : ATmega1284P Chip Erase delay : us PAGEL : PD7 BS2 : PA0 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack eeprom no xff 0xff flash yes xff 0xff lock no x00 0x00 lfuse no x00 0x00 hfuse no x00 0x00 efuse no x00 0x00 signature no x00 0x00 calibration no x00 0x00 Programmer Type : STK500 Description : Atmel STK500 Version 1.x firmware Hardware Version: 2 Firmware Version: 1.18 Topcard : Unknown Vtarget : 0.0 V Varef : 0.0 V Oscillator : Off SCK period : 0.1 us avrdude: AVR device initialized and ready to accept instructions Reading ################################################## 100% 0.02s

5 avrdude: Device signature = 0x1e9705 avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed To disable this feature, specify the -D option. avrdude: erasing chip avrdude: reading input file "C:\Program Files ega1284p_16mhz.hex" avrdude: writing flash ( bytes): Writing ################################################## 100% -0.00s avrdude: bytes of flash written avrdude: verifying flash memory against C:\Program Files ega1284p_16mhz.hex: avrdude: load data flash data from input file C:\Program Files ega1284p_16mhz.hex: avrdude: input file C:\Program Files ega1284p_16mhz.hex contains bytes avrdude: reading on-chip flash data: Reading ################################################## 100% 0.00s avrdude: bytes of flash verified avrdude: reading input file "0x0f" avrdude: writing lock (1 bytes): Writing ################################################## 100% 0.03s avrdude: 1 bytes of lock written avrdude: verifying lock memory against 0x0f: avrdude: load data lock data from input file 0x0f: avrdude: input file 0x0f contains 1 bytes avrdude: reading on-chip lock data: avrdude: 1 bytes of lock verified avrdude done. Thank you.