CORRECTION OF SERVICE MANUAL. Please correct your service manual

Transcription

1 CORRECTION OF SERVICE MANUAL Date: Dec. 1, 2005 No.: SCH05034 ( 1/7 ) MODEL No. S/M No. PG MODEL No. S/M No. PG DVD-R7322/ZUCYV/WL RRV Please correct your service manual Please refer to RRV2570 page Acquisition of the Error History The new version of Diagnose5 test program has been released. When you use new Diagnose5 of v2.960, please download from Niis site and see this information. PIONEER SERVICE NETWORK CORPORATION K.NOHARA,MANAGER HE Technical Support Group Service Engineering Division Memo: SMC06H021 NM, 62

2 7.1.7 ACQUISITION OF THE ERROR HISTORY This method is applied from v2.960 of GGS /7 If "Error Log" is selected and executed, internal information, such as error logs, is displayed on the screen. This internal information is also recorded in a file "driven.log," where n is the drive number. Description of error logs (Up to four error logs are displayed at one time.) Items 1 Execute Task, 2 Endeco Cmd, 3 Error Code, 4 Error Address Identify=ff Aging No.=0x0f Aging pointer=0x00 Controller Cmd=0x3e Controller step=0x06 Host Cmd=0x27 Endeco Cmd=0x0d< Error =0x90<---3. Execute Task=0x04< Error Address=0x00 0x00 0x00< Detail=0x00 0x00 First check item 1 Execute Task. It tells you with which command for a task an error was generated. The issued command is indicated in 2 Endeco Cmd. Then check item 3 Error Code. It tells you where the error was generated. In 4 Error Address, the address at which the error was generated is indicated as a Logical Block Address (LBA). 1 Execute Task 2 Endeco Cmd 3 Error Code 01h: An error was generated in the Mecha-con. See "Table 1: Mecha-con Command". See "Table 2 : Mecha-con Error". 02h: An error was generated in the der. See "Table 3 : Der Command". See "Table 4 : Der Error". 04h: An error was generated in the DVD enr. See "Table 5 : DVD enr Command". See "Table 6 : DVD enr Error". 08h: An error was generated in the CD enr. See "Table 7 : CD enr Command". See "Table 8 : CD enr Error". 10h: An error was generated in the controller. See "Table 9 : CD Controller Command". See "Table 10 : Controller Error". Note: Normally a command and error are issued from the same device. However, for a mechanical error during recording, the command is issued from the CD/DVD enr, but the error is issued from the mechanical-control computer.

3 Meaning of each item 3/7 Item Indentify Aging No. Aging pointer Controller Cmd Controller step Host Cmd Endeco command Error Execute task Error address Detail Meaning Indicates which is the latest error: The latest error is indicated as FFh. After an error was generated, if the power was turned off then back on and an error was generated again, the previous error is changed to BBh, and the latest error is indicated as FFh. After an error was generated, if the power was not turned off but an error was generated again, the previous error is changed to 00h, and the latest error is indicated as FFh. Indicates in which aging mode the unit was operating. Indicates which operation was being executed in the aging cycle. No indication is displayed for Normal mode. Indicates the mode the controller was in. Indicates the step of the mode the controller was executing. Details on this item are not described in this manual. Indicates an intermediate command that was issued from the host. (See Table 11.) No indication is displayed for aging. Indicates a command that was issued to the enr, der, or mechanical-control computer. Indicates an error that was returned from the enr, der, or mechanical-control computer. Indicates for which task the error was returned. Indicates the address where the error was generated. There may not be an error address. Indicates the details of the error. Details on this item are not described in this manual. EX: Identify=ff Aging No.=0x0f Aging pointer=0x00 Controller Cmd=0x07 Controller step=0x03 Host Cmd=0x62 Endeco Cmd=0x04 Error =0x0b Execute Task=0x02 Error Address=0x22 0x00 0x00 Detail=0x00 0x00 // Latest error // Normal mode // Read // Read // DVD User Data Read & De, Read Time Out // An error was generated in the der. // Address where the error was generated: LBA h In the above example, 1 The error was generated in the der. 2 The command being executed when the error was generated is "DVD User Data Read & De." 3 The status when the error was generated is "Read Timeout." 4 The address where the error was generated is "220000h."

4 Table 1 Mecha-con Command Table 2 Mecha-con error 00 NOP 80 Unsupported Command 01 Initialize 81 Illegal Mode 03 Unload 82 Illegal Request 04 Load 88 Loading Mecha NG 05 Park 89 TOC Read Error 08 Play 8a PrePit Read Error 09 Pause 90 Search Address Error 0a Rec 91 Illegal Track Request 0b Erase a0 No Disc 10 Setup a1 Disc NG 11 Setup1 a8 Servo NG Stop 12 Setup retry b0 Focus Close Fail 13 Setup end b1 Focus Servo Failure 17 XN Change b5 Focus Jump Fail 18 Search & Play c0 Track Close Fail 19 Search & Pause c1 Track Servo NG 1a Search & Record c2 Track Jump NG 20 LPP read d0 Spindle Start Fail 28 Disc Judge d1 Spindle Stop Fail 38 For examining BCA, etc. d2 Spindle High Speed Fail 39 Reading BCA d3 Spindle Low Speed Fail 3a Detection of existence of BCA d4 Spindle DVD Wob In Fail 49 RF End Seek d5 OPC end search Error 59 OPC End Seek d6 RF end search Error 4/7 Table 3 Der Command Table 4 Der error 01 DVD De Stop 01 De error 02 DVD De Clear 02 RF not exist 03 DVD User Data Cashe 03 RMD RF Not Exist 04 DVD User Data Read & De 04 Lead In RF Not Exist 05 RMD End Seek & Read 05 Lead In Not Complete 06 Layer0 Control Data De 06 Illegal Read Request 07 Layer1 Control Data De 07 Detect Interface Abort Request 08 R physical Information Data De 08 Mecha Search Time Over 09 CGMS Data De 09 Buffering Time Over 0a Set Read Ahead 0a Retry Time Over 0b RMD 1,3 Area Clear 0b Read Time Out 0c RMD Read for Verify 10 m63 Internal Error 0d DVD No DMA Data Read 11 m63 Formatter Error 0e DVD Leadout check 12 m63 Target ID Over Error 81 CD De Stop 13 m63 Header Compare Error 82 CD De Clear 14 m63 Uncorrectable Error 83 CD User Data Cashe 15 m63 CRC Error 84 CD User Data Read & De 16 m63 ETC Error 85 CD User Data Read & 1a m63 Transport Error De for Read CD Command 1b mecha not active 86 CD Lead in TOC Read 1c mecha no error 87 CD Lead in TOC Read 1d data error 88 CD Text Data Read 1e target to far 89 CD PreGap TDB Data Read 1f m63 nor active 8a 8b 8c 8d 8e 8f 90 CD Play Audio CD Play Audio MSF CD Play Audio TRK/IDX CD Play Audio Pause/Resume CD Play Audio Abort CD Play Audio Check Stat CD No DMA Data Read

5 Table 5 DVD Enr Command Table 6 DVD Enr error 00 ENC_CMD_NONE 40 Buffer full 01 DAO_WRITE 41 Buffer underrun 02 DATA_WRITE 42 OPC power insufficient 03 FLUSH_DAO 43 Excess OPC power 04 FLUSH_INC 44 OPC failed. 05 LEADIN_WRITE 45 Encoding failed. 06 LEADOUT_WRITE 46 DMA failed. 07 BORDERIN_WRITE 47 DECSS measures 08 BORDEROUT_WRITE The rotation speed of the spindle was not the BORDERLOUT_WRITE same as that during OPC. 0a 0b 0c 0d 0e 0f PADDING_WRITE CONTROL_WRITE RMD_WRITE OPC_WRITE OPC_READ DC_ERASE TEST_WRITE TEST_WRITE_OFF WRITE_START_DAO WRITE_START_INC EE_WRITE AGING_WRITE DVDENC_RESET CHANGE_ID CM_WRITE 5/7 Table 7 CD Enr Command Table 8 CD Enr error 00 NOP 20 Buffer overrun b 2d Buffer underrun Discontinuous time data Allowed value for ASYOVR count exceeded Invalid Cue Sheet Disc Full Address Error Aborted by the host (where Pregap 2 is to be recorded) (where Pregaps 1 and 2 are to be recorded) (where CD-DA is to be recorded) (where Pregap 2 is to be recorded) (where Pregaps 1 and 2 are to be recorded) (Session at once) (where Pregap 2 is to be recorded) a 2c 2e Panic In Excess phase difference of the wobble servo Allowed ASYNC interpolation exceeded Non Cue Sheet Reserved Track Full Aborted because of a mechanical error Invalid Command 2f Target address exceeded 08 (where Pregaps 1 and 2 are to be recorded) OPC write error 0 30 (Before recording: retrial from recording) 09 (Session at once) OPC write error a (Session at once) (After recording: retrial from area search) 0b Import of Cue Sheet OPC read error c Recording onto the PMA (Before reading: retrial from reading) 0d OPC count recording OPC read error 1 0e OPC recording 33 (Data error: retrial from recording 0f OPC playback or area search) 10 Recording start OPC read high limit 11 Synchronize Cache 34 (Retrial after changing power range 12 Recording onto the lead-in to higher limit) 13 Recording onto the lead-out OPC read low limit 14 Close Track 35 (Retrial after changing power range 15 Erase to lower limit) 16 Format 36 En Start Error 17 Dummy-writing start 3a atip is over the search address 18 Dummy-writing stop 3b ctime is over the search address 19 Dummy-erasure start 3c atip is over the ctime 1a Dummy-erasure stop 3d ctime is over the atip 1b 1c 1d Self-writing Self-erasure EE Write

6 6/7 Table 9 Controller Command 00 No operation 3c Verify Format 2 RMD 72 dvd add border format 01 Mecha.con initialize 3d Verify Format 3 RMD dvd quick grow border Disc At Once 3e Do OPC format 03 Track at once 3f Read Lead-in physical data 74 dvd quick add border format 04 Track at once 40 Read Copyright Information 75 dvd quick format 05 Incremental write 41 Read Disc Key Close Intermediate Syncronized cashe Read Manufacturer's BORDER Read Information 77 Blank the disc 08 Read Read Pre-recorded 78 Minimally blank Seek Information in Lead-in 79 Blank a Track/RZone tail 0a Start/Stop Unit 44 Read Unique Disc 7a Disc Close Check 0b Reserve RZone command Identifier of the Disc 7b Border Close Check 0c Time Stamp data set 45 Read BCA 7c RZone Close Check 0d Send User Specific Data 46 DVD Write Lead In Synchronize Cache 0e No operation 47 DVD Write Lead Out 7d Incremental 0f No operation 48 DVD Write Border In (execution child ) 10 Micro download 49 DVD Write Border Out 7e Track start address check 11 No operation DVD Write Border 7f - 4a 12 No operation & Lead Out 80 Set CD Speed / Streaming 13 Syncronized cashe TAO 4b DVD Write Padding 81 Read DVD Structure List 14 Syncronized cashe Packet 4c DVD Write Control Data 82 DVD RF Seek 15 Synchronize Cache 4d DVD Write DC Erase 83 Get Last RZone NWA Session at once 4e Play Audio 84 Get 1st RZone NWA 16 Setup sequence 4f Play Audio Track/Index 85 Get 2nd RZone NWA 17 Setup sequence 50 Resume/Pause 86 Close RZONE execution 18 Spindle Stop sequence 51 Read CGMS, CPM 87 Speed down (Inactivity) 19 Tray open Read RMD in last DVD-RW setup a Tray close Border-out (compulsion BLANK DISC) 1b Setup ( with or without Read RMD 89 Physical Read 53 mecha tuning ) (rsn:relative sector number) 8a Rezero Unit 1c DVD Lead-in data read 54 fill Next Border Marker 8b Change Power Condition 1d Blank disc check write Pre Border In 8c Previous Border In check 55 1e Disc at once check or Lead In Next Border Marker 8d 1f Incremental write check 56 Close Disc for DVD close check 20 DVD-R setup 57 Send Cue Sheet 8e Border in close check 21 DVD-RW setup 58 Write Session at once 8f Border out close check 22 DVD-ROM setup Read Media Catalogue 90 Lead in close check CD Next writable check Number 91 Lead out close check 24 DVD Next writable check 5a Read ISRC 92 Border Lout close check 25 Close Track 5b Read Format Capacity 93 RZone Repair 26 Close Session 5c Set Read Ahead 94 Next Border Marker Repair 27 Close Disc for CD 5d Read Header 95 Border In Repair 28 Close RZONE 5e Send CPM, CGMS 96 Border Out Repair 29 Close BORDER 5f Send Write Protection Data 97 Lead In Repair 2a Get RZone Information 60 Report AGID 98 Lead Out Repair 2b Get Track Information 61 Report Challenge Key 99 Border Lead Out Repair 2c OPC execute 62 Report Key1 9a Repair Disc (DVD-R/RW) 2d OPC execute 63 Report Title Key 9b Read CD Text Data 2e CD OPC execute check 64 Report ASF 9c CD Full format 2f DVD OPC execute check 65 Report RPC State 9d Physical Write 30 PreGap Read 66 Annul AGID 9e Start Recording ( Packet Track check ) 67 Send Challenge Key c8 time wait (for aging) 31 PreGap Length Check 68 Send Key2 Disc inner search & pause c9 Synchronize Cache 69 Send RPC Structure (for aging) 32 Incremental 6a Enter/Exit Test Write Mode Disc outer search & pause ca 33 Reserve Track TAO First track information (for aging) 6b 34 Reserve Track Packet check cb Disc trace (for aging) Write and Verify Format 1 Get track information cc Audio play (for aging) 35 6c RMD (execution child ) If aging time is over, cd Write and Verify Format 2 Syncronized cashe TAO tray out (for aging) 36 6d RMD (execution chkid ) ce CD track reserve (for aging) 37 Write and Verify Format 3 Syncronized cashe PKT cf CD data write (for aging) 6e RMD (execution chkid ) d0 CD data read ( for aging) 38 Write Format 1 RMD Synchronize Cache SAO DVD rzone reserve 6f d1 39 Write Format 2 RMD (execution chid ) (for aging) 3a Write Format 3 RMD 70 dvd full format d2 DVD data write (for aging) 3b Verify Format 1 RMD 71 dvd grow border format

7 7/7 Table 9 Controller Command Table 11 Host Command d3 d4 DVD data read & verify CD Minimally blank No opertation Minimally blank DVD Next Writable Start Recording (for aging) (for aging) Blank the disc Blank a Track/Rzone 32 Address Check Read Capacity d5 DVD Disc erase (for aging) 04 Unreserve a Track 33 Read Format Capacity d6 CD-RW full format 05 Blank a Track/RZone tail 34 Read Lead-in physical data d7 DVD-RW full format Unclose the last 35 Read Copyright Information 06 CD Disc NWA check Session/Border 36 Read Disc Key d8 (for aging) 07 Erase Session/Border 37 Read BCA d9 DVD Disc NWA check 08 Full Format for CD Read Manufacturer's 38 (for aging) 09 Full Format for DVD Information rzone/track close 0a Grow Border 39 Read CGMS, CPM da (for aging) 0b Add Border Read RMD in last 3a db CD-R data write full area 0c Quick Grow Borde Border-out dc DVD-R data write full area 0d Quick Add Border Read RMD 3b 0e Quick Format (rsn:relative sector number) 0f Close Track Read Pre-recorded 3c Table 10 Controller Error 10 Close Session Information in Lead-in 11 Close Disc for CD Read Unique Disc Identifier 3d 60 Command Sequence Error 12 Close Rzone of the Disc 61 Logical Unit 13 Close Border 3e Read DVD Structure List Communication Failure 14 Close Disc foe DVD 3f Read Audio Status Illegal Logical Block Close Intermediate 40 Read CD Current Position Address Border Read Subchannel Internal Controller Error Synchronize Cache All Format Privent Medium Removal Disc at once Read Media Catalogue System Resource Failure 17 Synchronize Cache Number 66 Authentication Failure Incremental 43 Read ISRC 67 Key Not Present Synchronize Cache 44 Get Performance Key Not Established Session at once 45 Read CD Text Data 69 Authentication Not End Synchronize Cache 46 Read Header 19 6a Incompatible Format Track At once 47 Report AGID 6b Region Mismatch 1a Synchronize Cache Packe 48 Report Challenge Key 6c Region Reset Count Error Prevent/Allow Medium 49 Report Key1 1b 6d De-Conpression CRC Error Removal 4a Report Title Key 6e OPC area full 1c Repair Rzone 4b Report ASF 6f OPC area almost full 1d Annul AGID 4c Report RPC State 70 Parameter Value Invalied Reserve RZone DAO 4d Send User Specific Data 1e 71 Media detect error (size:rsv size) 4e Send CPM, CGMS 72 RMA almost full Reserve RZone Incremental 4f Send Write Protection Data 1f 73 Media not Present (size:rsv size) 50 Send Timestamp 74 Long Write In Progress Reserve Track TAO 51 Send Disc Control Block Session is not full (size:rsv size) 52 Send Challenge Key 76 Sub-Q is not valid Reserve Track Packet 53 Send Key2 21 track start arress is (size:rsv size) 54 Send RPC Structure 77 not valid 22 Seek 55 Send Cue Sheet 78 track end arress is not valid 23 Do OPC 56 Download Micro 79 track end arress error 24 Rezero Unit 57 Read at incomplete track 25 Set Read Ahead 58 Read CD 7a Pregap read error 26 Set Streaming 59 Read CD MSF 7b PMA is not complet 27 Set Write Speed 5a Physical Read 7f Data compare error 28 Start/Stop Unit 5b Write Disc at once ( for aging ) 29 Change Power Condition 5c Write Incremental 2a Play Audio 5d Write Session at once 2b Play Audio Track Index 5e Write Track at once 2c Resume/Pause 5f Write Packet 2d 2e 2f Get Track/ RZone Information Scan Enter/Exit Test Write Mode