Preparation and Installation of the Composite Type Rupture Disc (Light Lip and Heavy Lip) in 30 Seat Insert, Full-Bolted, and Union Type Holder

Transcription

1 GEP-7004 Rev. L Ref. ID: 5472 Preparation and Installation of the Composite Type Rupture Disc (Light Lip and Heavy Lip) in 30 Seat Insert, Full-Bolted, and Union Type Holder WARNING USER SHOULD READ AND THOROUGHLY UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING DISC. THESE INSTRUCTIONS DO NOT PURPORT TO ADDRESS ALL OF THE SAFETY FACTORS ASSOCIATED WITH THE DISC S USE IN SERVICE. IT IS THE RESPONSIBILITY OF THE USER TO ESTABLISH APPROPRIATE SAFETY, HEALTH, AND TRAINING MEASURES FOR THEIR PERSONNEL INSTALLING, SERVICING, OR WORKING IN AN AREA WHERE DISC ASSEMBLIES ARE IN USE. SERVICE AND/OR MAINTENANCE ON OR AROUND THE DISC DEVICE MUST NOT BE PERFORMED WHILE THE DEVICE IS SUBJECTED TO OPERATING PRESSURES AND/OR TEMPERATURES. IT IS THE USER S SOLE RESPONSIBILITY FOR DESIGN AND PLACEMENT OF DISCS WITHIN THEIR FACILITY AND UPON THE EQUIPMENT UPON WHICH THE DISC OF USER S SELECTION IS TO BE LOCATED. IT IS USER S SOLE RESPONSIBILITY FOR THE DESIGN OF ADEQUATE VENTING AND INSTALLATION OF ADEQUATE VENT PIPING OR DIRECTIONAL FLOW AFTER OCCURS WITH THE DISC AS INTENDED. WHEN SIZE IS SPECIFIED, CONTINENTAL DISC CORPORATION ASSUMES THAT ADEQUATE PROVISIONS HAVE BEEN MADE BY PURCHASER FOR PROPER VENTING OF A SYSTEM TO RELIEVE THE SPECIFIC PRESSURE. LOCATE DISC WHERE PEOPLE OR PROPERTY WILL NOT BE EXPOSED TO THE SYSTEM DISCHARGE IN CASE OF. VENT TOXIC OR FLAMMABLE FUMES OR LIQUIDS TO A SAFE LOCATION TO PREVENT PERSONAL INJURY OR PROPERTY DAMAGE. IT IS THE USER S SOLE RESPONSIBILITY TO SPECIFY THE BURST PRESSURE RATING OF A DISC AT A COINCIDENT TEMPERATURE AT WHICH THE DISC IS TO BE USED. A DISC IS A TEMPERATURE SENSITIVE DEVICE. THE BURST PRESSURE OF THE DISC IS DIRECTLY AFFECTED BY ITS EXPOSURE TO THE COINCIDENT TEMPERATURE. GENERALLY, AS THE TEMPERATURE AT THE DISC INCREASES, THE BURST PRESSURE DECREASES; INVERSELY, AS THE TEMPERATURE AT THE DISC DECREASES, THE BURST PRESSURE MAY INCREASE. FAILURE TO PROPERLY UTILIZE A DISC AT THE SPECIFIED COINCIDENT TEMPERATURE COULD CAUSE PREMATURE FAILURE OR OVERPRESSURIZATION OF A SYSTEM. THE INSTANTANEOUS RELEASE OF PRESSURE FROM THE DISC CAN CREATE VIOLENT NOISES DUE TO THE DISCHARGE AT SONIC VELOCITY. IT IS THE USER S SOLE RESPONSIBILITY TO PROTECT AGAINST HEARING DAMAGE TO ANY BYSTANDERS. DISCS AND TAGS ARE MADE OF METAL FOILS OF VARYING THICKNESS. THE METAL EDGES MAY BE SHARP. PERSONNEL INSTALLING OR EXAMINING THE DISCS SHOULD PROTECT AGAINST CUTS OR INJURY WHEN HANDLING THE DISC. DO NOT LIFT A DISC BY ITS ATTACHED TAG. PARTICLES MAY BE DISCHARGED WHEN THE DISC S. THESE PARTICLES MAY BE PART OF THE DISC ITSELF, OR OTHER ENVIRONMENTAL MATTER IN THE SYSTEM. IT IS THE USER S SOLE RESPONSIBILITY TO ASSURE THAT THESE PARTICLES ARE DIRECTED TO A SAFE AREA TO PREVENT PERSONAL INJURY OR PROPERTY DAMAGE. THERE IS NO GUARANTEE OF DISC LIFE. SUCH LIFE SPAN IS AFFECTED BY CORROSION, CREEP AND FATIGUE, AND PHYSICAL DAMAGE. THESE CONDITIONS WILL DERATE THE DISC TO A LOWER SET PRESSURE. THE CUSTOMER AND/OR USER SHOULD BE PREPARED TO HANDLE PREMATURE FAILURE OF THE DISC. THE MEDIA OR OTHER ENVIRONMENTAL CONDITIONS SHOULD NOT ALLOW ANY BUILDUP OR SOLIDIFICATION OF MEDIA TO OCCUR ON A DISC. THIS MAY INCREASE THE PRESSURE SETTING OF THE DISC. CUSTOMER AND/OR ITS INSTALLER SHALL BE SOLELY RESPONSIBLE FOR THE PROPER INSTALLATION OF SELLER S S AND DISCS INTO A SYSTEM. CUSTOMER AND/OR ITS INSTALLER SHALL BE SOLELY RESPONSIBLE FOR IMPROPER INSTALLATION AND PHYSICAL DAMAGE RESULTING THEREFROM, INCLUDING BUT NOT LIMITED TO, DAMAGE RESULTING FROM LEAKAGE, IMPROPER TORQUING OR SEATING OF A DISC OR FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS WHERE PROVIDED. DISCS ARE PRECISION SAFETY DEVICES AND MUST BE INSTALLED PROPERLY. DISCS MUST BE INSTALLED BY TRAINED, KNOWLEDGEABLE INSTALLERS AND ONLY WITHIN ENVIRONMENTS SUITABLE AND APPROPRIATE FOR A DISC. CARE MUST BE USED IN A FACILITY'S DESIGN TO PROTECT BOTH THE DISC FROM INADVERTENT DAMAGE WHICH COULD CAUSE ITS PREMATURE RELEASE AND TO PROTECT INDIVIDUALS EXPOSED TO HAZARDS CREATED BY SUCH SUDDEN RELEASE. PROPER INSTALLATION OF A DISC IS CRITICAL TO PERFORMANCE AND TO SAFETY. FAILURE TO PROVIDE PROPER SEATING OF A DISC MAY AFFECT DISC PERFORMANCE, BURST PRESSURE ACCURACY AND MAY RESULT IN ITS PREMATURE FAILURE.

2 I. Safety Precautions Before Installation 1. The Composite Type rupture disc is a precision instrument and must be handled with extreme care. Rupture discs should be installed only by qualified personnel familiar with rupture discs and proper piping practices. 2. Do not install rupture disc if there is any damage in the dome area. A damaged rupture disc is any rupture disc with visible nicks or dents in the dome. 3. Continental Disc Corporation does not recommend reinstalling a rupture disc that has been removed from the holder as reinstallation may adversely affect the joint sealing capabilities and/or performance of the rupture disc. 4. See rupture disc tag to verify set pressure, operating temperature, and all other operating parameters. II. Insert Type 30 Seat Holder A. Preparation of Holders for Installation New Installation Clean all foreign material from the rupture disc sealing area of both the holder inlet and outlet. Replacement Installation 1. Remove the holder from the system and place on a flat surface. Figure 'A' 2. Disassemble the holder by loosening the pre-assembly screws, or by removing the pre-assembly cap screws, whichever is applicable. Lift the holder outlet up and set aside; then remove the burst rupture disc. 3. Clean the rupture disc sealing area of both the holder inlet and outlet. These surfaces must be completely clean and free of all rust, corrosion, and foreign material to ensure a proper seal. Use of solvents, steel wool, or fine emery cloth is permissible. Do not remachine. Do not use scraper or abrasives. 4. Inspect the rupture disc sealing area for nicks, scratches, or pitting. If any of these conditions are present, consult the factory for repair. 5. Remove any adhered gasket material from previous installation. B. Assembly of the Rupture Disc and Holder (See Figure A) OUTLET DISC VACUUM SUPPORT (OPTIONAL) INLET DISC TAG Component parts of the Insert Type 30 Seat Holder assembly are illustrated in the proper installation sequence. 1. Carefully remove and discard any shipping protectors furnished with rupture discs or holder. DO NOT INSTALL A SHIPPING PROTECTOR IN A ASSEMBLY. 2. Place the holder inlet on a flat surface. 3. Place the COMPOSITE Type rupture disc on the holder inlet opening with the dome side facing up as illustrated. FLOW DIRECTION Figure 'B' STUD NUT 4. Align and lower the holder outlet carefully onto the holder inlet. GASKET 5. Fasten the assembly together by tightening the pre-assembly screws or by replacing and tightening the pre-assembly cap screws. C. Installation of the Insert Type 30 Seat Holder Assembly Into the System (See Figure B) 1. Before placing the assembly into the system, ensure that the companion flange gasket surfaces are clean and free of all rust, corrosion, and foreign material. 30 SEAT ASSEMBLY GASKET DISC TAG FLOW DIRECTION 2

3 2. A J-Hook (optional) may be provided in the holder inlet to ensure correct installation of the assembly relative to flow direction. If the J-Hook is used, the corresponding inlet companion flange must be drilled to accommodate the J- Hook prior to installation of the assembly. Refer to the J-Hook Installation Guide for locating and drilling specifications. NOTE: If replacing another Preventative Maintenance manufacturer s holder, the corresponding inlet companion flange must be re-drilled to accommodate the J-hook in the LAMOT holder inlet. 3. Install the Insert Type 30 Seat Holder assembly and customer furnished gaskets, WITH ALL FLOW ARROWS POINTING IN THE PROPER FLOW DIRECTION, and the J-Hook (if furnished) inserted into the drilled companion flange. 4. Install lightly oiled, free running studs and nuts to finger tightness. Using a cross torquing pattern (see Figure C), torque each nut with a calibrated torque wrench at 20% increments of recommended torque value (see Table 1). Repeat 20% increments and cross torquing pattern until final torque value is achieved. Recheck all nuts in rotational sequence at final torque value. When properly torqued, the distance between the holder inlet and the holder outlet should be approximately equal around the perimeter of the holder. These values are based on using gasket materials having a gasket factor of 2.75, gasket seating stress of 3,700 psi, and stud and nut material per ASME SA193-B7 and SA194-2H respectively, with a stress of up to 25,000 psi. The use of studs and nuts with lower strength may prove unsatisfactory. Figure 'C' EXAMPLE OF BOLT TORQUE SEQUENCE III. Full-Bolted Type 30 Seat Holder A. Preparation of Holders for Installation New Installation 8 - BOLTS Clean all foreign material from the rupture disc sealing area of both the holder inlet and outlet. Replacement Installation 1. Remove the studs and nuts that hold the assembly together. 2. Separate the inlet and outlet; then remove the burst rupture disc. 3. Clean the rupture disc sealing area of both the holder inlet and outlet. These surfaces must be completely clean and free of all rust, corrosion, and foreign material to ensure a proper seal. Use of solvents, steel wool, or fine emery cloth is permissible. Do not remachine. Do not use scraper or abrasives. OUTLET Figure 'D' STUD NUT 4. Inspect the rupture disc sealing area for nicks, scratches, or pitting. If any of these conditions are present, consult the factory for repair. 5. Remove any adhered gasket material from previous installation. DISC B. Assembly of the Rupture Disc and Holder (See Figure D) Component parts of the Full-Bolted Type 30 Seat Holder assembly are illustrated in the proper installation sequence. 1. Carefully remove and discard any shipping protectors furnished with rupture discs or holder. DO NOT INSTALL A SHIPPING PROTECTOR IN A ASSEMBLY. VACUUM SUPPORT (OPTIONAL) INLET DISC TAG 2. Place the COMPOSITE Type rupture disc on the holder inlet opening with the dome side facing up as illustrated. 3. Align and lower the holder outlet carefully onto the holder inlet. FLOW DIRECTION 3

4 4. Install lightly oiled, free running studs and nuts to finger tightness. Using a cross torquing pattern (see Figure C), torque each nut with a calibrated torque wrench at 20% increments of recommended torque value (see Table 1). Repeat 20% increments and cross torquing pattern until final torque value is achieved. Recheck all nuts in rotational sequence at final torque value. When properly torqued, the distance between the holder inlet and the holder outlet should be approximately equal around the perimeter of the holder. These values are based on using gasket materials having a gasket factor of 2.75, gasket seating stress of 3,700 psi, and stud and nut material per ASME SA193-B7 and SA194-2H respectively, with a stress of up to 25,000 psi. The use of studs and nuts with lower strength may prove unsatisfactory. IV. Union Type Holder A. Preparation of Holders for Installation New and Replacement Installation 1. Clean the rupture disc sealing area of both the holder inlet and outlet. These surfaces must be completely clean and free of all rust, corrosion, and foreign material to ensure a proper seal. Use of solvents, steel wool, or fine emery cloth is permissible. Do not re-machine. Do not use scraper or abrasives. 2. Care should be taken during assembly and installation to ensure that nothing sharp protrudes down through the inlet or outlet cavities. A rupture disc that has been scratched, dented, or damaged in any way, may result in premature failure. B. Assembly of the Rupture Disc and Holder (See Figure E) Component parts of the Union Type assembly are illustrated in the proper installation sequence. 1. Carefully remove and discard any shipping protectors furnished with rupture discs or holder. DO NOT INSTALL A SHIPPING PROTECTOR IN A ASSEMBLY. 2. Place the holder inlet on a flat surface. 3. Position the rupture disc in the holder inlet with the dome side facing up as shown. Handle with care. 4. Carefully lower the holder outlet onto the rupture disc. 5. Slip the nut over the holder outlet and thread it onto the holder inlet. Place a wrench on the holder inlet to keep it from turning. Using a calibrated torque wrench, torque the nut to the following requirements: Torque for Discs w/fluoropolymer Seals Pressure Rating Torque Requirement Size Holder (Ft Lbs) (N m) 1/ / Torque for Discs w/metal Seals Pressure Rating Torque Requirement Size Holder (Ft Lbs) (N m) 1/ /

5 C. Installation of the Union Type Assembly into the System (See Figure F) 1. Assure that the unit being installed is compatible with current system operating conditions. 2. Before installing the Union Type assembly into the system, clean mating threads of all grit, dirt, or foreign material to ensure proper seal. 3. Install the Union Type Assembly WITH ALL FLOW ARROWS POINTING IN THE PROPER FLOW DIRECTION. 4. When installing the assembly into the system, do not tighten or loosen seal between holder inlet and holder outlet, for this could cause damage to the rupture disc or cause premature failure. V. Preventative Maintenance 1. Risk assessment and an annual rupture disc replacement are recommended. Rupture disc service life is determined by system operating conditions. The effects of severe pressure/vacuum cycles, corrosion, temperature variations, or other adverse conditions must be evaluated by the user through actual service experience to determine optimal service life. 2. IF THE DISC IS NOT REPLACED PERIODICALLY WHEN EXPOSED TO THESE CONDITIONS, PREMATURE FAILURE OF THE DISC MAY OCCUR, THEREBY DISCHARGING THE PROCESS MEDIA. 3. To avoid extended downtime, maintain three spare rupture discs in stock at all times for each holder in use. The number of spares required ultimately will be determined by service conditions. VI. Customer Service If you wish to discuss your application, installation, or maintenance, please contact the Customer Service Department at one of the addresses shown on the last page of these instructions 5

6 Recommended Torque Values for Composite Type Rupture Discs (Light Lip and Heavy Lip) TABLE 1 SIZE COMPANION FLANGES DISCS WITH FLUOROPOLYMER SEALS DISCS WITH METAL SEALS IN. MM ANSI DIN JIS TORQUE (FT LB) TORQUE (N m) TORQUE (FT LB) TORQUE (N m) / /16/ / / / / ½ ½ /16 10/16/ ½ / ½ / ½ / ½ / ½ / / / / / / / / / / / / / /

7 Recommended Torque Values for Composite Type Rupture Discs (Light Lip and Heavy Lip) TABLE 1 (continued) SIZE COMPANION FLANGES DISCS WITH FLUOROPOLYMER SEALS DISCS WITH METAL SEALS IN. MM ANSI DIN JIS TORQUE (FT LB) TORQUE (N m) TORQUE (FT LB) TORQUE (N m) / / / / / / /

8 First Certified in 1992 If stamped, this product is built in accordance of the ASME Boiler and Pressure Vessel Code, Section VII, Division 1. China Manufacture License Products are in full compliance with the provisions of the Peoples Republic of China Import Regulations for Boiler and Pressure Vessel safety devices. 3A Sanitary Standards Stamp If stamped, this product is in full compliance with the 3A standards, Serial #60-00, of the International Association of Milk, Food and Environmental Sanitarians, Inc. European Union CE Mark If stamped, this product is certified to conform to the essential requirements of the Pressure Equipment Directive. Continental Disc Corporation has representatives located throughout the world. Contact the office nearest you for the authorized representative in your area. Continental Disc Corporation reserves the right to alter the information in this publication without notice. Reproduction without written permission prohibited. Printed in U.S.A. 1994, 1995, 1997, 1998, 2002, 2003, 2005, 2008, 2009, 2010, 2012, 2013, 2014 Continental Disc Corporation