OPERATION MANUAL. USB Datalogger (Temp./RH/Thermocouple)

Transcription

1 OPERATION MANUAL USB Datalogger (Temp./RH/Thermocouple)

2 INTRODUCTION & OPERATION A very smart and cost-effective mini USB logger, save your cost without logger cradle! Many different parameters are selectable with the modern shape design, versatile application is applicable and applied. Ultrasonic sealed housing meets IP57 water resistant for Temp.RH models. Sensor cap LCD display model shows :Temperature and Relative humidity interchange ( models only) :Temperature ( USB cap Battery compartment easy to replace battery Sensor part LED: Green and Red Green LED flashing stands for logging is in process Red LED flashing stands for reading exceeds High or Low alarm threshold. Button start USB connector and button stop for activate or inactivate logger recording Wrist strip conveniently carry around and avoid falling off Logger tripod receptacle for tripod mountable device Lithium battery ½ AA size User friendly USB driver and logger software CD P1

3 LOGGER SPECIFICATION Spec./ Model no Record data Temperature Temperature, RH LCD display We supply the unique feature for thermocouple logger with relative humidity recording: Spec./ Model no Sample interval Logger mode 0~6hours, 0~59 minutes, 0~59 seconds, ( 1 second to 6 hours) Key start/stop,immediately, Schedule, Real-time Temp.range ( ) YES ( NO ) K:-200~1370. YES ( NO ) K:-200~1370. J:-200~760, T:-200~390 YES (NO ) K:-200~1370. YES (NO ) Sample interval Start mode From 1 seconds to 6 hours Key start/stop, Real-time, Schedule, Immediately Temp.range -40.0~85.0 (-40~185 ) Accuracy Dew Point, Wet Bulb Temp. N/A +0.6 (-20~50 ), others+1.2 N/A YES Heat Index,WBGT Temp. N/A N/A YES RH % range accuracy N/A N/A 0.1%RH~99.9%RH +3%RH(at 25,10~90%RH, Memory capacity- Total Opeating Temp. 0~50 (32~122 )<80%RH K:-200~1370. J:-200~760, T:-200~390 ( ) K:-328~2372 K:-328~2372, J:-328~1400, T:-328~734 K:-328~2372 K:-328~2372, J:-328~1400, T:-328~734 Resolution Accuracy (K) 0.5 (Display 1 / ) ±(0.1% rdg+0.7 ) (J) N/A ±(0.1% rdg+0.7 ) N/A ±(0.1% rdg+0.7 ) (T) N/A ±(0.1% rdg+0.7 ) N/A ±(0.1% rdg+0.7 ) Dew Point, Wet Bulb Temp. N/A N/A N/A YES Heat Index. WBGT Temp. N/A N/A N/A YES RH % range N/A N/A 0.0%RH~99.9%RH accuracy N/A N/A +3%RH(at 25,10~90%RH, others+5%rh) Memory capacity- Total Opeating Temp. RH 0~50 (32~122 ),,80%RH The standard package supplied : a) USB logger unit with USB clear cap (All models), sensor cap (Temp.RH models) b) CD (USB driver and logger software) c) 1/2AA lithium battery x 1 pc d) Operation and installation manual e) White plain box f) Wrist stip x 1 g) K type thermocouple probe ( 9858x5 series only). J.T type are optional. Battery : 3.6V 1/2AA x 1 Battery life depends on sample rate, ambient temperature and sample point setting, normally one year. P2

4 A. Install logger driver for Windows The PL2303_Prolific_DriverInstaller_v110.exedriver is for Windows operation system, follow the installation steps hereunder: 1. Put the CD into CD driver, click PL2303_Prolific_DriverInstaller_v110.exe for installation the driver.. 2. The set up status 3. Click NEXT to continue. 4 After complete the installation, press Finished B. Install the logger software for Windows XP Please follow the following steps to install the software 1.Put CD into CD driver, click Setup.exe MSI Installer Bootstrapper National Instruments to install P3

5 2 Select the destination folder you are go to save by click Browse button 3 Once you finish selecting,press Next. 4.Select I accept the License Agreemen:(s) and press NEXT button. 5.Click NEXT button when you see the following. 6.Press FINISH button to complete the installation. 7 Restart the Windows XP system P4

6 . Run the software from Windows XP 1. Plug the USB datalogger into USB port, since you have already installed the USB driver, computer will automatically detect logger, click My computer Content in hardware content, click Device manager to find the listed (COMx) listed under Ports(COM & LPT) as below with red circle. If you may Prolific USB-to-Serial Comm. Port, it means the logger is connected to computer properly, if you can't see it, you may run 1. Install logger driver for Windows) rd 2. Select logger software folder ( The 3 step of logger software installation) 3.Clck below 4. The screen of logger software as below: 5. Click Setting Comm port select the port number as you see from step 2, then press OK button. P4 Logger setting: Software is installed completed, Get Datalog s Identifier shows below, then press SETTING button to enter Log setting(pic.1) Note: If logger is not plugged in USB port, the warning message Reminder: Data Logger is not plugged in USB port! shows below(pic.2) Make sure logger is plugged in and choose the correct COM port. (Pic.1) (Pic.2) LOGGER Status: Before download data, press LOGGER status to show ID, Records, Sample rate, Unit... NOTE: Once Download button is pressed, recording is inactivated. P5

7 (Pic.3) (Pic.4) (Pic.5) BASIC:(Pic.3) Step1:ID setting Maximum 20 characters, name your logger and press OK button to confirm. Step2:Current Date/Time Clock setting, the system automatically shows current date and time of your pc. Press OK to confirm.(note: Schedule date and time refers to the current pc date and time) button to confirm. Step3: LCD display set Press ON (LCD still illuminated after complete recording ), or OFF ( LCD is not illuminated after complete recording. Press OK after selection. Use LCD display ON may keep monitoring the status. ALARM&SENSOR:(Pic.4) Stpe1:Alarm setting Select Temp./Humidity alarm, set Hi/Lo Temp. and H/Lo Humidity values. SETTING:(Pic.5) Step1: Set sample point (K=1,000 multiple basis within total memory points) For examples: 16K memory store 8,000 points each of 2 parameters or store 5,333 points each of 3 parameters or store 16,000 points of selected parameter 32K memory store 16,000 points each of 2 parameters or store 10,666 points each of 3 parameters or store 32,000 points of selected parameter Select the parameter (Temperature, Humidity RH% or thermocouple type: K.J.T. or others), press OK to confirm the sample points and parameters. Step2:Set sample rate, start mode to record Select hour(1~6), minute(0~59), second(0~59) Select start mode from : Immediately, Schedule, Real-time (Pc is always connected with the logger unit)and Key start (Start recording by pressing button). Choose Immediately mode, the logger starts to record after press OK on logger setting screen, green LED is flashing to stand for logging function. Red LED flashing stands for readings exceed High Low alarm setting. Step3:Select Unit : Select Temperature unit C/ F,press OK after confirmed. P6

8 Download data: Press DOWNLOAD button, data download in few seconds. Graph shows automatically NOTE: Please do not perss DOWNLOAD button before you want stop record. You can press LOGGER STATUS button to see record points. Data area/message area Beside DOWNLOAD button, it is data area shows the cursor parameter s value Beside EXIT button, it is Reminder and Warning message area. Retrieve file: Press RETRIEVE FILE button to select file and show the graph. Save data: Press SAVE button to save txt. file. Or Excel, PDF file (Available soon by updating newest logger software version) Print graph: Press PRINT button and print graph. Follow the print setting below to print full screen graph. Press OK to print pdf file.(pic.6) View Data Table: Press View button to get data table with details.(pic.7) Print Table Data: Press table data, the screen shows the record range, enter the start number to the end number (For example: 1~500 or 200~ or leave it blank for printing all data ).(pic.8) (pic.6) (pic.7) (pic.8) P7

9 Real-time start mode: 1.After set start mode at real-time,datalogger starts login records. When the logger records each point, the fan at left corner shows green 2.When real-time selected, it shows QUIT button instead of DOWNLOAD at the right corner. Press QUIT to stop real-time recording. Key-start mode: Press NOTE: The button is designed for not easy to touch, users have to use a sharp pin to touch (If you set up start mode as BUTTON ),to prevent carelessly touch to start or stop the recording. After set up key start as start mode, remove the logger from USB port. Use a sharp pin to push the middle of gray button, until you hear a click sound, the LED will flash to start recording. Zoom in/out Hold Ctrl + Click Mouse = Screen graph zoom in Hold Screen graph zoom out Ctrl + Click Mouse = Line color selecting: 1.Click the color beside the reading(temp. RH), color box shows below. 2.Move mouse to review and select color. 3.Click to save, the color appear on line and bar. P8