SOFTWARE CONFIGURATION GUIDE

Size: px

Start display at page:

Download "SOFTWARE CONFIGURATION GUIDE"

Dorothy Dickerson
5 years ago
Views:

SOFTWARE For Veris Aerospond Wireless Sensors and the NWGWA2 Wireless Gateway INTRODUCTION This guide is intended to aid in the configuration of a

sensors. To configure a network, the user must first download the software from the Veris website, www.veris.com.

CONFIGURATION Getting Started 1. Before beginning the configuration, contact the building administrator or IT administrator.

In return, the admin must provide a unique IP address, gateway address, and subnet mask for each device, as well as the network name, network

1 SOFTWARE For Veris Aerospond Wireless Sensors and the NWGWA2 Wireless Gateway INTRODUCTION This guide is intended to aid in the configuration of a wireless network that utilizes the Veris Aerospond NWGWA2 network wireless gateway with Veris Aerospond wireless (Wi-Fi) temperature and humidity sensors. To configure a network, the user must first download the software from the Veris website, This software requires Java version 7 or higher to run correctly. Java must match the operating system format (32 or 64 bit). CONFIGURATION Getting Started 1. Before beginning the configuration, contact the building administrator or IT administrator. Provide the administrator a list of all device MAC addresses (printed on the devices). In return, the admin must provide a unique IP address, gateway address, and subnet mask for each device, as well as the network name, network passphrase or WEP, and the SSID. 2. Locate the link on the Veris website, to download the software. Save the folder to the PC. 3. Open the folder and select the ACT_LAUNCHER.bat file. ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

In the Network Configuration tab, enter the network name, SSID, location, channel and passphrase,

2 Using the software. 1. In the Project tab, enter a Customer Name and Job ID. Then click Add New Project. 2. In the Network Configuration tab, enter the network name, SSID, location, channel and passphrase, as supplied by the building administrator or IT administrator. Click Add New Network. ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

Select the Device Configuration tab and enter the quantities of each wireless device to

3 3. Click on the new network created in step 2. Select the Group Configuration tab and enter a Group Name. Click Add New Group. 4. Select the Device Configuration tab and enter the quantities of each wireless device to be used in the installation. Click OK. ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

Each device type (JACE, Gateway, or sensor) has a different set of tabs. Required fields in these tabs are designated by the red icon).

4 5. When the device tree appears in the left panel, click on the adjacent icons to fully expand the tree, showing all devices. 6. To configure each device to the wireless network, click on it and enter the information requested. Each device type (JACE, Gateway, or sensor) has a different set of tabs. Required fields in these tabs are designated by the red icon). When information is successfully entered and accepted by the software, the icon turns yellow,. JACE: Click on the JACE in the device tree and fill in all required data. Click Apply. ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

Sensors: Click on each sensor in the device tree and fill in all

5 Gateway: Click on the Gateway in the device tree and fill in all required data. Click Apply. Sensors: Click on each sensor in the device tree and fill in all required data. Click Next. ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

If integrating the sensor with a JACE controller, use the drop-down list to select the JACE that the sensor will communicate with. Click Apply to complete sensor configuration.

6 If integrating the sensor with a JACE controller, use the drop-down list to select the JACE that the sensor will communicate with. Click Apply to complete sensor configuration. Repeat this step for each sensor. If integrating the sensor with a Gateway, use the drop-down list to select the Gateway that the sensor will communicate with and configure the sensor outputs. Click Apply to complete sensor configuration. Repeat this step for each sensor. ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

Complete Configuration 1. To map a device, remove the cover and locate the RS-232 port.

Note: Connect the NWGWA2 to a 20-30 VDC power supply before connecting the AWB01 cable (see the NWGWA2

RS-232 port Config button Power switch RS-232 port Config button 2. Select the Download tab. 3.

Click to select the correct communication port that the cable is plugged into.

7 Complete Configuration 1. To map a device, remove the cover and locate the RS-232 port. Connect the AWB01 configuration cable (sold separately) to the PC using this port. Note: Connect the NWGWA2 to a VDC power supply before connecting the AWB01 cable (see the NWGWA2 product installation guide for detailed wiring information). RS-232 port Config button Power switch RS-232 port Config button 2. Select the Download tab. 3. The red progress bar indicates that the configuration software has not located a device. Click to select the correct communication port that the cable is plugged into. If unsure which port is connected, use the Help Locate Port ID button, then follow the instructions that appear on the screen. ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

The progress bar turns yellow when the port is located, signaling that the software recognizes the device. Press the Config button on the device to load the networking data and map the device.

8 The progress bar turns yellow when the port is located, signaling that the software recognizes the device. Press the Config button on the device to load the networking data and map the device. The progress bar turns green when mapping is complete. 4. Remove the AWB01 cable. 5. NWGWA2 only: to make the new configuration data take effect, flip the power switch into the off position, then back into the on position. ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

9 6. Replace the device cover. 7. Repeat steps 1 through 6 for each device. Device Installation When all devices are configured and mapped by the software, you may now install them throughout the building. See the individual product installation guides for instructions on properly mounting these devices. ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

10 ZL0107-0A PAGE Veris Industries USA or / support@veris.com 12122

The SC receives a public IP address from the DHCP client of the ISP. All traffic is automatically sent out through the WAN interface.

The SC receives a public IP address from the DHCP client of the ISP. All traffic is automatically sent out through the WAN interface. Barracuda NextGen Secure Connectors can connect to the Internet using DHCP client, static, or Wi-Fi client connections. The connections can be configured through the Secure Connector Editor or, for troubleshooting