ic-tw11 EVAL TW11_1C EVALUATION BOARD DESCRIPTION
|
|
- Candace Long
- 5 years ago
- Views:
Transcription
1 ic-tw11 EVAL TW11_1C ar y n i im prel Rev A2, Page 1/7 ORDERING INFORMATION Type Order Designation Evaluation Board ic-tw11 EVAL TW11_1C Description Options ic-tw11 Evaluation Board Ready-to-operate, includes mini-usb cable Optional Software ic-tw11 GUI GUI software for Windows PC Device readout and setup For download link check BOARD TW11_1C Figure 1: Board image Copyright 2014 ic-haus
2 ic-tw11 EVAL TW11_1C ar y n i im prel Rev A2, Page 2/7 RELATED DOCUMENTS ic-tw11 documentation LAYOUT AND TERMINALS TERMINAL DESCRIPTION P1 Mini-USB socket for PC connection (for GUI communication and board supply with 5 V) P4/P8 GPIOx GND SAMPLE VBUS SCLK Daisy-chain connectors General purpose in/out for custom use Ground (USB ground) Triggers position conversion Voltage output used to indicate daisy-chaining Sense input for daisy-chaining (pull-down) Interrupt request from ic-tw11 Interrupt chain input Active-low chip reset SPI Master-In/Slave-Out of MCU (connected to SO if not in daisy-mode) SPI Slave-In SPI Slave-Out (connected to MISO if not in daisy-mode) Active-low SPI Slave-Select Board supply voltage (connected to USB 5 V) SPI Clock P3 C2D C2CK Silabs MCU programming interface MCU programming interface: data MCU programming interface: clock P2 V_CORE V_IO Supply voltages Core supply voltage (input) I/O supply voltage (input) P7 TM0 TP0 TM1 TP1 Test pins 3.3V D_SENSE IRQ_OUT IRQ_IN xrst MISO SI SO xss Figure 2: Board image Figure 3: Board layout LEDs LED D2 LED D1 Negative test pin channel 0 Positive test pin channel 0 Negative test pin channel 1 Positive test pin channel 1 "Power" (green) indicates 5 V on VBUS "SPI active" (red) indicates that the MCU is driving the SPI interface (high-z if deactivated)
3 Rev A2, Page 3/7 CIRCUIT SCHEMATIC Figure 4: Connections to the SiLabs C8051F320 MCU
4 Rev A2, Page 4/7 Figure 5: Connections to ic-tw11
5 Rev A2, Page 5/7 ASSEMBLY PART LIST Reference Footprint Rate Manufacturer Part# Count C1,C2 SMD uF 2 C3,C4 SMD uF 2 C5 SMD nF 1 C6 SMD0603 1uF 1 C7 SMD nF 1 C8 SMD0603 1uF 1 D1 SMD0805 Red Stanley BR1112H-TR 1 D2 SMD0805 Green Stanley BG1112H-TR 1 FB1 SMD Ohm Laird MI0805K400R-10 1 P1 USB_MINI_B USB_MINI_B TE Connectivity R1,R2 SMD R3,R4 SMD0603 1k 2 R5,R6 SMD R7 SMD R11 SMD k 1 R12 SMD k 1 U1 QFN16-4x4mm ic-tw11 ic-haus ic-tw11* 1 U2 DRL_SN74LVC1G125 SN74LVC1G125 Texas Instruments SN74LVC1G125DBVR 1 U3 LQFP32 C8051F320 Silicon Laboratories C8051F320 1 *) The evaluation board is equipped with a ic-tw11 chip release C1. Advanced chip samples are available for the evaluation of standby current consumption.
6 Rev A2, Page 6/7 GETTING STARTED Step Description Download GUI-Software For the evaluation software please check The package includes all files which are necessary for operation. Install GUI-Software When download is finished, open the download folder and double click "TW111SO_gui_XX/setup.exe". Follow the instructions on the screen. Connect Demoboard Plug the mini-usb cable to the ic-tw11_1c mini-usb connector and find a free USB slot on your Windows PC. The green "Power" LED will light up once the board is powered. Start GUI-Software Double click on the TW111SO_gui_XX.exe in your installation folder to start the GUI. The red "SPI active" LED indicates that the MCU is driving the SPI interface now. Start the Help system To help you interact with the GUI, there is a help system which teaches you about the main features of the GUI software. You will find the help system in the menubar "Help", as shown below. Figure 6: Help system
7 Rev A2, Page 7/7 REVISION HISTORY Rel Rel.Date Chapter Modification Page A All Initial Release all Rel Rel.Date Chapter Modification Page A LAYOUT AND TERMINALS Description modified 2 ASSEMBLY PART LIST Note added on chip release 5 GETTING STARTED Description modified 6 ic-haus expressly reserves the right to change its products and/or specifications. An info letter gives details as to any amendments and additions made to the relevant current specifications on our internet website this letter is generated automatically and shall be sent to registered users by . Copying even as an excerpt is only permitted with ic-haus approval in writing and precise reference to source. ic-haus does not warrant the accuracy, completeness or timeliness of the specification and does not assume liability for any errors or omissions in these materials. The data specified is intended solely for the purpose of product description. No representations or warranties, either express or implied, of merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to information/specification or the products to which information refers and no guarantee with respect to compliance to the intended use is given. In particular, this also applies to the stated possible applications or areas of applications of the product. ic-haus conveys no patent, copyright, mask work right or other trade mark right to this product. ic-haus assumes no liability for any patent and/or other trade mark rights of a third party resulting from processing or handling of the product and/or any other use of the product.
ic-mu EVAL MU1C MOTOR FEEDBACK EVALUATION KIT DESCRIPTION
Rev B4, Page 1/10 ORDERING INFORMATION Type Order Designation Description Options Evaluation kit ic-mu EVAL MU1C Evaluation kit includes PCB module MU1C, magnetic code disc MU2S 30-32N, cable signal output
More informationic-mu EVAL MU2M 3-TRACK NONIUS EVALUATION KIT DESCRIPTION
Rev A, Page /7 ORDERING INFORMATION Type Order Designation Description Options Evaluation Kit ic-mu EVAL MUM Evaluation kit includes board MUM populated with two ic-mu DFN6-5x5 and an two EEPROMs (see
More informationic-mh EVAL MH1D EVALUATION BOARD DESCRIPTION
Rev A5, Page 1/10 ORDERING INFORMATION Type Order Designation Description Options Evaluation Board ic-mh EVAL MH1D ic-mh Evaluation Board ready to operate, accessible through GUI via PC adapter Software
More informationMB4U BiSS, SSI, PC-USB 2.0 ADAPTER
MB4U Rev B1, Page 1/5 FEATURES APPLICATIONS BiSS / SSI application development BiSS / SSI debugging Flexible interface configuration Encoder calibration Portable applications USB 2.0 high speed PC interface
More informationic-msb EVAL MSB1D EVALUATION BOARD DESCRIPTION
Rev A2, Page 1/7 ORDERING INFORMATION Type Order Designation Description and Options Evaluation Board ic-msb EVAL MSB1D ic-msb Evaluation Board ready to operate, accessible through GUI via PC adapter Software
More informationic-mcw EVAL MCW1D EVALUATION KIT DESCRIPTION
Rev A2, Page 1/11 ORDERING INFORMATION This evaluation kit includes the evaluation board MCW1D (assembled with ic-mcw QFN24), and an USB (A-B) cable for PCs. Type Description Options Order Designation
More informationic-mh EVAL MH1D EVALUATION BOARD DESCRIPTION
Rev A4, Page 1/9 ORDERING INFORMATION Type Order Designation Description Options Evaluation Board ic-mh EVAL MH1D ic-mh Evaluation Board ready to operate, accessible through GUI via PC adapter Software
More informationic-hf EVAL HF1D EVALUATION BOARD DESCRIPTION
Rev B1, Page 1/8 ORDERING INFORMATION Type Order Designation Description Options Evaluation Board ic-hf EVAL HF1D ic-hf Evaluation Board ready to operate: Encoder Link Sequence and power down available
More informationic-ht EVAL HT1D EVALUATION BOARD DESCRIPTION
Rev A2, Page 1/12 ORDERING INFORMATION Type Order Designation Description Options Evaluation Board ic-ht EVAL HT1D ic-ht Evaluation Board ready to operate, accessible through GUI via USB including USB
More informationic-htp EVAL HTP1D EVALUATION BOARD DESCRIPTION
Rev A1, Page 1/11 ORDERING INFORMATION Type Order Designation Description Options Evaluation Board ic-htp EVAL HTP1D ic-htp Evaluation Board ready to operate, accessible through GUI via USB including USB
More informationic-mhm EVAL MHM1D EVALUATION BOARD DESCRIPTION
Rev A3, Page 1/12 ORDERING INFORMATION Type Order Designation Description Evaluation board ic-mhm EVAL MHM1D ic-mhm evaluation board Ready-to-operate, includes adapter MHM3M, accessible by GUI using PC
More informationic-px Series EVAL PXM EncoderBlue EVALUATION KIT DESCRIPTION
Rev A1, Page 1/5 ORDERING INFORMATION The evaluation kit includes a scanner module PX1M assembled with ic-pxnnnn. Please refer to Page 4 for an overview of kit parts. EncoderBlue is a trademark of ic-haus
More informationic-nq EVAL NQ1D EVALUATION BOARD DESCRIPTION
Rev B4, Page 1/6 ORDERING INFORMATION Type Order Designation Description/Options ic-nq Demo EVAL NQ1D ic-nq Evaluation Board with BiSS PC Adapter ready-to-operate, incl. adapter MB3A equipped with ic-mb3
More informationMB3U, MB3U-I2C BiSS TO PC-USB ADAPTER
Rev A5, Page /7 ORDERNG NFORMATON Type Order Designation Options PC Adpater ic-mb3 icsy MB3U BiSS to PC-USB Adapter ic-mb3 icsy MB3U-C BiSS and C to PC-USB Adapter Software BiSS GU GU software for Windows
More informationMB3D ic-mb3 BiSS MASTER DEMO-BOARD
Release B1, Page 1/6 ORDERING INFORMATION Type Ordering Information Descriptions/Options ic-mb3 Demo Board MB3D-S MB3D-P Demo board for connecting BiSS/SSI sensors to the LPT port on a PC (serial configuration)
More informationic-nq, ic-nqc EVAL NQ6D EVALUATION BOARD DESCRIPTION
ic-nq, ic-nqc EVL NQD EVLUTION ORD DESCRIPTION Rev, Page /0 ORDERING INFORMTION Type Order Designation Description Options Evaluation oard ic-nq EVL NQD ic-nq Evaluation oard ic-nqc EVL NQD ic-nqc Evaluation
More informationic-tl6 BLCC Point Source LED
Rev A1, Page 1/6 FEATURES High brightness Ultra Red LED Glass cover High temperature range -40 to 125 C SMD 1206 LED Package APPLICATIONS Illumination for high resolution optical encoder, PSDs and optical
More informationic-pv EVAL PV1D EVALUATION BOARD DESCRIPTION
Rev A1, Page 1/10 ORDERING INFORMATION Type Order Designation Description Options Evaluation Board ic-pv EVAL PV1D ic-pv Evaluation Board Ready-to-operate, supplied with magnet, accessible by GUI using
More informationic-mhl200 EVAL MH2D EVALUATION BOARD DESCRIPTION
ar y n i im prel ic-mhl00 EVL MH EVLUTION BOR ESCRIPTION Rev, Page / ORERING INFORMTION Type Order esignation escription Options Evaluation Boards ic-mhl00 EVL MH Evaluation board for MHLM pcb connection
More informationUM0401 User manual. User manual for eight bit port expander STMPE801 demonstration board. Introduction
User manual User manual for eight bit port expander STMPE801 demonstration board Introduction This document explains the functioning of the demo board for the port expander Chip STMPE801 with a PC GUI
More informationAN10428 UART-SPI Gateway for Philips SPI slave bridges
UART-SPI Gateway for Philips SPI slave bridges Rev. 01 7 March 2006 Application note Document information Info Keywords Abstract Content UART-SPI Gateway, UART to SPI, RS-232 to SPI The UART-SPI Gateway
More informationFigure 1. 8-Bit USB Debug Adapter
8-BIT USB DEBUG ADAPTER USER S GUIDE 1. Introduction The 8-bit USB Debug Adapter (UDA) provides the interface between the PC s USB port and the Silicon Labs 8-bit target device s in-system debug/programming
More informationic-hd7 QUAD DIFFERENTIAL LINE DRIVER
Rev A6, Page 1/8 FEATURES Complementary short-circuit-proof push-pull driver stages for RS422 and 24 V applications up to 2 MHz Pin-compatible to 26LS31, xx7272 Integrated line adaptation for high signal
More informationTable of Contents 1 Typical Applications General Description Block Diagram Pinout System Connections Typical A
Data Sheet: Product Preview Rev 0.3, 3/2014 Xtrinsic 3-Axis Digital Angular Rate Gyroscope is a small, low-power, yaw, pitch, and roll angular rate gyroscope. The full-scale range is adjustable from ±250
More informationic-mh16 Evaluation Software Software Description
Rev A1, Page 1/14 DESCRIPTION ic-haus ic-mh16 evaluation software is developed for PCs running the Windows operating system. The evaluation software is developed in LabVIEW and requires a one-time installation
More informationic-hvxxxv 200 MHz LASER SWITCH preliminary WITH INTEGRATED POWER VCSEL ARRAY
Rev A1, Page 1/10 FEATURES VCSEL output from CW up to 200 MHz Integrated power VCSEL array Three independent channels for bias and pulse control TTL and LVDS inputs VCSEL array supply voltage up to 5.5
More informationic-mn AN5 APPLICATION NOTE: CIRCUIT EXAMPLES
i-mn N5 PPLITION NOTE: IRUIT EXMPLES Rev 5, Page 1/6 OPTIL ROTRY ENOER 6 isc i-pnxxxx PS_N N_N PS_M N_M PS_S N_S V RLE 47 P_N NS_N P_M NS_M P_S NS_S LE i-tl85 VREF PS_N NS_N P_N N_N PS_M NS_M P_M N_M PS_S
More informationSi7005USB-DONGLE. EVALUATION DONGLE KIT FOR THE Si7005 TEMPERATURE AND HUMIDITY SENSOR. 1. Introduction. 2. Evaluation Kit Description
EVALUATION DONGLE KIT FOR THE Si7005 TEMPERATURE AND HUMIDITY SENSOR 1. Introduction The Si7005 is a relative humidity and temperature environmental sensor in a 4 mm x 4 mm QFN package. Access to the sensor
More informationEVALKIT-VL6180X. VL6180X plug-in and STM32 F401RE Nucleo board explorer kit. Description. Features
EVALKIT-VL6180X VL6180X plug-in and STM32 F401RE Nucleo board explorer kit Data brief Equipped with Arduino UNO R3 connector. RoHS compliant. Full system SW supplied, download from www.st.com/vl6180x in
More informationUM PCAL6524 demonstration board OM Document information
Rev. 1 23 September 2015 User manual Document information Info Content Keywords OM13320 Fm+ development kit, OM13260 Fm+ I2C bus development board, OM13303 GPIO target board Abstract Installation guide
More informationEVB-USB3300 User Manual
EVB-USB00 User Manual Copyright 006 SMSC or its subsidiaries. All rights reserved. SMSC is a registered trademark of Standard Microsystems Corporation ( SMSC ). The information contained herein is proprietary
More informationEVB-USB2514Q36-BAS, USB2513 and USB Pin QFN Evaluation Board, Revision C User Manual
EVB-USB2514Q36-BAS, USB2513 and USB2512 36-Pin QFN Evaluation Board, Revision C User Manual Copyright 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating
More informationE Demonstration Board AN 0178 Dec 15, 2016
E.0 Demonstration Board AN 0 Dec, 0 E.0 Power LIN.X Stepper with Stall Detection What you get. Demoboard E.0 What you need in addition. V Power Supply, capable of providing the motor current. Bipolar stepper
More informationMB3U, MB3U-I2C BiSS, SSI, PC-USB ADAPTER
Rev C3, Page 1/16 FEATURES USB 2.0 compatible PC interface ic-mb3 TSSOP24 based BiSS master Hardware implemented interface protocols Fast realtime data communication (10 MHz BiSS; 4 MHz SSI) API for Windows
More informationWIZ810MJ Datasheet. (Ver. 1.2) 2007 WIZnet Inc. All Rights Reserved. For more information, visit our website at
(Ver. 1.2) 2007 WIZnet Inc. All Rights Reserved. For more information, visit our website at www.wiznet.co.kr Document History Information Revision Data Description Ver. 1.0 September, 2007 Release with
More informationCBC-EVAL-06. EnerChip CC Real-Time Clock Evaluation Kit. Product Discontinued - Not for New Designs
System Features and Overview CBC-EVAL-06 is a demonstration kit featuring the Cymbet EnerChip CBC3112 backup power and battery management circuit coupled with the Micro Crystal low power RV-2123 real-time
More informationAppNote-US2400-EVB Low Power 2.4GHz Transceiver
US2400-EVB for IEEE 802.15.4 Standard Revision History Hardware Revision Date Description of Changes V01 / V02 Sep. 2011 Initial release V03 Dec 2011 Addition 4.1 Evaluation Board Variants and 5.3 Connector
More informationThe USB Debug Adapter package contains the following items: USB Debug Adapter (USB to Debug Interface) with attached 7 Ribbon Cable
USB DEBUG ADAPTER USER S GUIDE 1. Contents The USB Debug Adapter package contains the following items: USB Debug Adapter (USB to Debug Interface) with attached 7 Ribbon Cable 2. USB Debug Adapter Specifications
More informationZSSC4151 Evaluation Kit Hardware Manual
Important Notes Restrictions in Use IDT s ZSSC4151 SSC Evaluation Kit, consisting of the SSC Communication Board (SSC CB), ZSSC415x/6x/7x Evaluation Board (SSC EB), Sensor Replacement Board (SSC RB), and
More informationBIG8051. Development system. User manual
BIG8051 User manual All s development systems represent irreplaceable tools for programming and developing microcontroller-based devices. Carefully chosen components and the use of machines of the last
More informationEvaluation Board User Guide UG-047
Evaluation Board User Guide UG-047 One Technology Way P.O. Box 9106 Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 Fax: 781.461.3113 www.analog.com Evaluating the ADT7310/ADT7410 Temperature Sensors
More informationAN3001 Application note
Application note Demonstration board user guidelines for the TS4657 single supply stereo digital audio line driver Introduction This application note focuses on the TS4657 demonstration board, designed
More informationSi7005USB-DONGLE. EVALUATION DONGLE KIT FOR THE Si7005 TEMPERATURE AND HUMIDITY SENSOR. 1. Introduction. 2. Evaluation Kit Description
EVALUATION DONGLE KIT FOR THE Si7005 TEMPERATURE AND HUMIDITY SENSOR 1. Introduction The Si7005 is a relative humidity and temperature environmental sensor in a 4 mm x 4 mm QFN package. Access to the sensor
More informationEthernet1 Xplained Pro
Ethernet1 Xplained Pro Part Number: ATETHERNET1-XPRO The Atmel Ethernet1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The board enables the user to experiment with
More informationPlease refer to "4. Evaluation Board" on page 2 for more information about these steps. Figure 1. System Connections
CP2120 EVALUATION KIT USER S GUIDE 1. Kit Contents The CP2120 Evaluation Kit contains a CP2120 evaluation board and a power supply. The following supporting documents can be downloaded from www.silabs.com:
More informationEVB-USB2250 User Manual Revision B
Copyright 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
More informationUM0726 User manual STEVAL-PCC009V1, universal USB to serial communication interface (UUSCI) based on the STM32x Introduction
UM0726 User manual STEVAL-PCC009V1, universal USB to serial communication interface (UUSCI) based on the STM32x Introduction This user manual explains the functions of the STM32-based universal USB to
More informationTable 1. RS232 Serial Adapter DEBUG Connector Pin Descriptions
RS232 SERIAL ADAPTER (EC2) USER S GUIDE 1. Contents The RS232 Serial Adapter (EC2) package contains the following items: RS232 Serial Adapter (RS232 to Debug Interface) 7 Ribbon Cable 2. RS232 Serial Adapter
More informationAN2240 Application note
AN0 Application note Using the evaluation board for the TS7 low noise microphone preamplifier with V bias Introduction This application note describes the DEMO TS7 evaluation board, specifically designed
More informationHVP-KV31F120M User s Guide
Freescale Semiconductor, Inc. User s Guide Document Number: HVPKV31F120MUG Rev. 0, 12/2014 HVP-KV31F120M User s Guide by: Ivan Lovas 1 High voltage controller card HVP-KV31F120M This document supports
More informationic-hd2 QUAD DIFFERENTIAL LINE DRIVER
Rev A6, Page 1/8 FEATURES Complementary short-circuit-proof push-pull driver stages for RS422 and 24 V applications up to 2 MHz Pin-compatible to xx2068 Integrated line adaptation for high signal quality
More informationEval Kit Manual. DN[Document ID] CCS811. Standard Board CCS811-LG_EK_ST. ams Eval Kit Manual Page 1
Eval Kit Manual DN[Document ID] CCS811 Standard Board CCS811-LG_EK_ST ams Eval Kit Manual Page 1 Content Guide 1 Introduction... 3 2 General Description... 3 2.1 USB to I 2 C Board (ENS-USB-I2CIO)... 3
More informationZLED7030KIT-D1 Demo Kit Description
ZLED7030KIT-D Demo Kit Description Kit Important Notice Restrictions in Use IDT s ZLED7030KIT-D Demo Kit hardware is designed for ZLED7030 demonstration, evaluation, laboratory setup, and module development
More informationGENERAL DESCRIPTION MC3635 FEATURES
Quick Start Guide and Demo GENERAL DESCRIPTION The MC3635 is an ultra-low power, lownoise, integrated digital output 3-axis accelerometer with a feature set optimized for wearables and consumer product
More informationAN10688_1. PN532C106 demoboard. Document information. NFC, PN532, PN532C106, demoboard. This document describes PN532C106 demoboard.
AN10688_1 Rev.0.1 February 1, 2008 Application note Document information Info Keywords Abstract Content NFC, PN532, PN532C106, demoboard This document describes. Revision history Rev Date Description 0.1
More informationams AG austriamicrosystems AG is now The technical content of this austriamicrosystems document is still valid. Contact information:
austriamicrosystems AG is now The technical content of this austriamicrosystems document is still valid. Contact information: Headquarters: Tobelbaderstrasse 30 8141 Unterpremstaetten, Austria Tel: +43
More informationMB4U BiSS, SSI, PC-USB 2.0 ADAPTER
Rev C2, Page 1/16 FEATURES USB 2.0 high speed PC interface FPGA based logic Hardware implemented interface protocols Fast realtime data communication (10 MHz BiSS; 4 MHz SSI) API for Windows : BiSS-Interface
More informationic-lo EVAL LO1D EVALUATION BOARD DESCRIPTION
ic-lo EVAL LO EVALUATION BOAR ESCRIPTION Rev A, Page /3 ORERING INFORMATION Type Order esignation escription Options Evaluation Board ic-lo EVAL LO ic-lo Evaluation Board ready to operate, accessible through
More informationChrontel CH7251A for USB Type-C Charger
Chrontel for USB Type-C Charger Features Component for USB Type-C Charger(USB Type-C Specification 1.2) On chip 3A switch. On chip over voltage, over current and over temperature detection and protection.
More informationFor more detailed information about this product please refer to the QT510 datasheet.
E510 1 User Manual 2 E510 User Manual OVERVIEW This kit is designed for evaluation and development of QT510-based QWheel Rotary slider. It includes a fully assembled rotary slider evaluation board, user
More informationUSER GUIDE. Atmel OLED1 Xplained Pro. Preface
USER GUIDE Atmel OLED1 Xplained Pro Preface Atmel OLED1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The board enables the user to experiment with user interface applications
More informationLevel Shifter. for. Hardware User s Manual.
Level Shifter for USB-to to-i2c Hardware User s Manual https://www.i2ctools.com/ Information provided in this document is solely for use with the I2C and SPI Level Shifter from SB Solutions, Inc. SB Solutions,
More informationQT2 Xplained Pro. Preface. Atmel QTouch USER GUIDE
Atmel QTouch QT2 Xplained Pro USER GUIDE Preface Atmel QT2 Xplained Pro kit is an extension board that enables the evaluation of a mutual capacitance touch surface using the Peripheral Touch Controller
More informationKIT33972AEWEVBE Evaluation Board
Freescale Semiconductor, Inc. User s Guide Document Number: KT33972UG Rev. 1.0, 7/2013 KIT33972AEWEVBE Evaluation Board Featuring the MC33972A Multiple Switch Detection Interface IC Contents Figure 1.
More informationUSER GUIDE. Atmel PROTO1 Xplained Pro. Preface
USER GUIDE Atmel PROTO1 Xplained Pro Preface The Atmel PROTO1 Xplained Pro extension kit is a development board that can be used to prototype small circuits and easy connect it to Xplained Pro MCU boards
More informationEVB-USB2517 Evaluation Board User Manual (Revision A)
EVB-USB2517 Evaluation Board User Manual (Revision A) Copyright 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means
More informationHVP-MC56F82748 User s Guide
Freescale Semiconductor, Inc. User s Guide Document Number: HVPMC56F82748UG Rev. 0, 12/2014 HVP-MC56F82748 User s Guide by: Ivan Lovas 1 High voltage controller cards overview This document supports the
More informationAN231K04-DVLP3 AnadigmApex Development Board
1.0 Overview The AnadigmApex development board is an easy-to-use platform designed to help you get started with implementing and testing your analog designs on the AnadigmApex FPAA silicon devices. While
More informationmotioncookie SYSTEM IN A PACKAGE
motioncookie SYSTEM IN A PACKAGE motioncookie TMCC160-EVAL MANUAL TMCC160 TMCL Hardware Version 1.1 Document Revision 1.0 2015-AUG-16 The TMCC160-EVAL is designed for evaluating all features of the TMCC160-LC
More informationE Demonstration Board AN 0177 Dec 15, 2016
E. Demonstration Board AN 0 Dec, 0 E. Power LIN.X Stepper with Stall Detection What you get. Demoboard E. What you need in addition. V Power Supply, capable of providing the motor current. Bipolar stepper
More informationRFID Reader Board 13.56MHz RFID Transceiver MLX90132
Table of Contents 1. General Description... 2 1.1 Connector X1 (SPI/ UART Communication)... 2 2. MLX90132 Pin Definitions & Descriptions... 3 2.1 MLX90132 simplified Block Diagram... 3 3. RFID90132 Circuit
More informatione-link Emulation/Programming Adapter Cable (ESTD-206) User s Guide
Cable (ESTD-206) User s Guide Revision: V1.00 Date: December 12, 2018 Table of Contents e-link Emulation/Programming Adapter Cable (ESTD-206) Introduction... 3 For the e-link On-Chip Debug Function OCDS...
More informationUM1750 User manual. STEVAL-IPE023V1: STPMxx programmer. Introduction
User manual STEVAL-IPE023V1: STPMxx programmer Introduction This evaluation board is a tool for programming the STPMxxx energy meter ICs family. The board has been developed to provide an insulated USB
More informationEVB8720 Evaluation Board User Manual
Copyright 2011 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
More informationUG271: CP2615-EK2 User's Guide
The CP2615 device is designed to enable rapid development of USB-based audio applications. The CP2615 simplifies the process of transferring audio data from USB to I2S without any code development, speeding
More informationUSB-to-I2C. Professional Hardware User s Manual.
USB-to-I2C Professional Hardware User s Manual https://www.i2ctools.com/ Information provided in this document is solely for use with the USB-to-I2C Professional product from SB Solutions, Inc. SB Solutions,
More informationAN2474 Application note
AN474 Application note TS4995.W fully differential audio power amplifier with selectable standby and 6db fixed gain - Evaluation board user guidelines Introduction This application note describes the DEMO
More informationSystem-on-Chip Battery Board User s Guide
System-on-Chip Battery Board User s Guide swru241 Table of Contents 1 Introduction...3 2 About this Manual...3 3 Acronyms and Definitions...3 4 Kit Contents...4 5 Hardware Description...5 5.1 LED, Button
More informationEVB-USB2640 Evaluation Board Revision A
Copyright 2008 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
More informationUSB3740. High Speed Switch for Mobile and Portable Applications USB3740 PRODUCT FEATURES DATASHEET. USB3740 Block Diagram
USB3740 High Speed Switch for Mobile and Portable Applications PRODUCT FEATURES High Speed USB Mux for multiplexing the USB lanes between different functions Switch the USB connector between two different
More informationEVB-USB2240-IND User Manual Revision B
Copyright 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
More informationugreen DAB Board Instructions v5
ugreen Instructions v5 1 Introduction The v4 is a revised and more efficient new version of the. Its smaller layout allows a better integration into most Raspberry Pi enclosures. It is available in two
More informationUSB3740 Evaluation Board User Manual
USB0 Evaluation Board User Manual Copyright 0 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical
More informationUSB3319. Hi-Speed USB Transceiver with 1.8V ULPI Interface - 13MHz Reference Clock PRODUCT FEATURES. Applications. Data Brief
USB3319 Hi-Speed USB Transceiver with 1.8V ULPI Interface - 13MHz Reference Clock PRODUCT FEATURES Data Brief USB-IF Hi-Speed compliant to the Universal Serial Bus Specification Rev 2.0 Interface compliant
More informationMSP430-PG2231 development board Users Manual
MSP430-PG3 development board Users Manual All boards produced by Olimex are ROHS compliant Revision A, June 0 Copyright(c) 0, OLIMEX Ltd, All rights reserved Page INTRODUCTION: MSP430-PG3 is prototype
More informationE Mux Demonstration Board AN 0141 Jul 10, 2015
1 What you get: 1. One or more demonstration boards 2. Board description (this document) 3. USB Stick or CD - with driver for elmos LIN converter - GUI - flash and auto-addressing software 2 What you need
More informationHVP-KV10Z32 User s Guide
Freescale Semiconductor, Inc. User s Guide Document Number: HVPKV10Z32UG Rev. 0, 12/2014 HVP-KV10Z32 User s Guide by: Ivan Lovas 1 High voltage controller card HVP-KV10Z32 This document supports the HVP-MC3PH
More informationMPU-6000/MPU Axis Evaluation Board User Guide
MPU-6000/MPU-6050 9-Axis Evaluation Board User Guide InvenSense, Inc., 1197 Borregas Ave., Sunnyvale, Ca 94089, USA 1 AN-MPU-6000EVB-00 Table of Contents 1. REVISION HISTORY... 3 2. PURPOSE... 4 2.1 USAGE...
More informationUSB2I 2 C Programming Kit Quick-Start User s Guide
Revision A USB2I 2 C Programming Kit Quick-Start User s Guide General Description The SMX3203 USB programming system is used for device prototype development. The SMX3203 system consists of a programming
More informationEvaluation Board for CS5345
Evaluation Board for CS5345 Features Single-ended Analog Inputs Single-ended Analog Outputs CS8406 S/PDIF Digital Audio Transmitter Header for Optional External Software Configuration of CS5345 Header
More informationMC3635 FEATURES GENERAL DESCRIPTION
GENERAL DESCRIPTION MC3635 FEATURES The MC3635 is an ultra-low power, low noise, integrated digital output 3-axis accelerometer with a feature set optimized for wearables and the Internet of Moving Things
More informationEVB-USB2514Q36-BAS, USB2513 and USB Pin QFN Evaluation Board User Manual
EVB-USB2514Q36-BAS, USB2513 and USB2512 36-Pin QFN Evaluation Board User Manual Copyright 2008 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products
More informationSmart Card Bridge to Full-Speed USB, SPI, and UART Interfaces
SEC00/SEC200 Bridge to Full-Speed USB, SPI, and UART Interfaces PRODUCT FEATURES Data Brief General Description The SEC00 and SEC200 provide a single-chip solution for a bridge to USB, SPI, and UART interfaces.
More informationEVB-USB2514Q48 48-Pin QFN Evaluation Board Revision A1
EVB-USB2514Q48 48-Pin QFN Evaluation Board Revision A1 Copyright 2007 SMSC or its subsidiaries. All rights reserved. The information contained herein is proprietary to SMSC and shall be used solely in
More informationUSB2512. USB 2.0 High-Speed 2-Port Hub Controller PRODUCT FEATURES
USB2512 USB 2.0 High-Speed 2-Port Hub Controller PRODUCT FEATURES General Description The SMSC 2-Port Hub is a low power, OEM configurable, STT (Single transaction translator) hub controller IC with 2
More informationQT3 Xplained Pro. Preface. Atmel QTouch USER GUIDE
Atmel QTouch QT3 Xplained Pro USER GUIDE Preface The Atmel QT3 Xplained Pro is an extension board, which enables the evaluation of a capacitive touch 12 key numpad in mutual capacitance configuration.
More informationTP80301 Data Sheet Copyright SIGMATONE Version 1.0
1 Copyright Version 1.0 2 Disclaimer Information contained in this data sheet regarding device applications is provided only for your convenience and may be superseded by updates. Sigmatone makes no representations
More informationic-hg 3 A LASER SWITCH
Rev A1, Page 1/19 FEATURES Six channel laser switch from CW up to 200 MHz CW operation with up to 500 ma per channel Spike-free switching of the laser current 6 x 1 channels with TTL inputs 3 x 2 channels
More informationEnerChip RTC Evaluation Kit CBC34803 Real-Time Clock with Integrated Backup Power. CBC-TAB Registers
System Features and Overview CBC-EVAL-12-34803 is a demonstration kit featuring the Cymbet CBC34803 EnerChip RTC - an integrated surface mount device combining an Ambiq Micro AM0803 Real-Time Clock (RTC),
More informationPRODUCT SPECIFICATION
nrfl0+ Evaluation System nrfl0+-evsystem INTRODUCTION This document describes the nrfl0+ EVSYSTEM and its use with the Nordic Semiconductor nrfl0+ REFMOD. GETTING STARTED The nrfl0+ EVSYSTEM consists of
More information