ThinkCentre User Guide. Machine Types: 7522, 7560, 7610, and 7705

Transcription

1 ThinkCentre User Guide Machine Types: 7522, 7560, 7610, and 7705

2

3 ThinkCentre User Guide

4 Note Before using this information and the product it supports, be sure to read and understand the ThinkCentre Safety and Warranty Guide and Notices, on page 67. Third Edition (October 2009) Copyright Lenoo LENOVO products, data, computer software, and serices hae been deeloped exclusiely at priate expense and are sold to goernmental entities as commercial items as defined by 48 C.F.R with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or serices are deliered pursuant a General Serices Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F

5 Contents Important safety information Chapter 1. Product oeriew Features Specifications Software oeriew Software proided with your Windows operating system Locations Locating connectors on the front of your computer 7 Locating connectors on the rear of your computer 8 Locating components Locating parts on the system board Chapter 2. Installing options and replacing hardware Handling static-sensitie deices Installing options and replacing hardware Installing external options Opening the computer coer Accessing the system board components and dries Installing or replacing a memory module Installing or replacing a PCI card Installing internal dries Replacing the hard disk drie Replacing the optical drie Replacing the battery Replacing the power supply assembly Replacing the heat sink and fan assembly Replacing the microprocessor Replacing the keyboard Replacing the mouse Completing the parts replacement Installing security features Integrated cable lock Password protection Erasing lost or forgotten passwords (clearing CMOS) Chapter 3. Recoery information Creating and using recoery media Creating recoery media Using recoery media Performing backup and recoery operations Performing a backup operation Performing a recoery operation Using the Rescue and Recoery workspace Creating and using rescue media Creating rescue media Using rescue media Creating and using a recoery repair diskette Creating a recoery repair diskette Using a recoery repair diskette Installing or reinstalling deice driers Setting a rescue deice in the startup sequence.. 48 Soling recoery problems Chapter 4. Using the Setup Utility Starting the Setup Utility program Viewing and changing settings Using passwords Password considerations Power-On Password Administrator Password Setting, changing, and deleting a password Enabling or disabling a deice Selecting a startup deice Selecting a temporary startup deice Selecting or changing the startup deice sequence 52 Exiting from the Setup Utility program Chapter 5. Updating system programs 53 Using system programs Updating (flashing) BIOS from a disc Updating (flashing) BIOS from your operating system Recoering from a POST/BIOS update failure Chapter 6. Troubleshooting and diagnostics Basic troubleshooting Diagnostic programs Lenoo ThinkVantage Toolbox Lenoo System Toolbox PC-Doctor for Rescue and Recoery PC-Doctor for DOS Cleaning the mouse Optical mouse Non-optical mouse Chapter 7. Getting information, help, and serice Information resources Online Books folder Lenoo ThinkVantage Tools Lenoo Care Lenoo Welcome Access Help Safety and Warranty Lenoo Web site ( 64 Help and serice Using the documentation and diagnostic programs Calling for serice Using other serices Purchasing additional serices Appendix. Notices Copyright Lenoo 2009 iii

6 Teleision output notice European conformance CE mark Trademarks Index i User Guide

7 Important safety information CAUTION: Before using this manual, be sure to read and understand all the related safety information for this product. Refer to the ThinkCentre Safety and Warranty Guide that you receied with this product for the latest safety information. Reading and understanding this safety information reduces the risk of personal injury and or damage to your product. If you no longer hae a copy of the ThinkCentre Safety and Warranty Guide, you can obtain a Portable Document Format (PDF) ersion from the Lenoo Support Web site at: Copyright Lenoo 2009

8 i User Guide

9 Chapter 1. Product oeriew Features This chapter describes the computer features, specifications, preinstalled software programs, and part and connector locations. This section proides an oeriew of the computer features. System information The following information coers a ariety of models. For information about your specific model, use the Setup Utility program. See Chapter 4, Using the Setup Utility, on page 49. Microprocessor Intel Celeron processor Intel Celeron dual-core processor Intel Pentium dual-core processor Intel Core 2 Duo processor Intel Core 2 Quad processor Internal cache (size aries by model type) Memory Supports up to two double data rate 2 dual inline memory modules (DDR2 DIMMs) Internal dries Card reader (some models) Serial Adanced Technology Attachment (SATA) internal hard disk drie Optical drie (some models) Video subsystem Integrated graphics card for a Video Graphics Array (VGA) connector Peripheral Component Interconnect (PCI) Express x16 graphics card slot on the system board for a discrete graphics card Copyright Lenoo

10 Audio subsystem Integrated high-definition (HD) audio Audio line-in connector, audio line-out connector, and microphone connector on the rear panel Microphone connector and headphone connector on the front panel Internal speaker (some models) Connectiity 10/100/1000 Mbps integrated Ethernet controller PCI V.90 Data/Fax modem (some models) System management features Ability to store power-on self-test (POST) hardware test results Automatic power-on startup Preboot Execution Enironment (PXE) Remote Administration System Management (SM) Basic Input/Output System (BIOS) and SM software Wake on LAN Wake on Ring (in the Setup Utility program, this feature is called Serial Port Ring Detect for an external modem) Input/Output (I/O) features 9-pin serial port (one standard and one optional) Ethernet connector One standard 25-pin parallel port Standard keyboard connector Standard mouse connector Six USB connectors (two on the front panel and four on the rear panel) Two audio connectors on the front panel (microphone connector and headphone connector) Three audio connectors on the rear panel (audio line-in connector, audio line-out connector, and microphone connector) VGA monitor connector Expansion One hard disk drie bay One optical drie bay One drie bay for a card reader (some models) One PCI card slot One PCI Express x16 graphics card slot (aries by model type) Power 280-watt auto-sensing power supply Adanced Configuration and Power Interface (ACPI) support 2 User Guide

11 Security features Computrace Coer presence switch (also called intrusion switch) (some models) Hard disk drie password Keyboard with fingerprint reader (some models) Power-On Password (POP) and Administrator Password for BIOS access Serial and parallel port I/O control Startup sequence control Startup without diskette drie, keyboard, or mouse Support for the addition of an integrated cable lock (Kensington lock) Support to enable or disable a deice USB switch on/off Software programs, preinstalled Your computer might come with preinstalled software programs. If it does, an operating system, deice driers to support built-in features, and other support programs are included. For more information, see Software oeriew on page 5. Operating system, preinstalled Microsoft Windows 7 Microsoft Windows Vista Microsoft Windows XP Professional (preinstalled through downgrade rights in Windows 7 Professional, Windows 7 Ultimate, Windows Vista Business, or Windows Vista Ultimate) Operating systems, certified or tested for compatibility 1 (aries by model type) Linux 1. The operating systems listed here are being certified or tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by Lenoo as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been certified or tested for compatibility, check the Web site of the operating system endor. Chapter 1. Product oeriew 3

12 Specifications This section lists the physical specifications for your computer. Dimensions Width: 317 mm (12.48 inches) Height: 99 mm (3.9 inches) Depth: 355 mm (13.98 inches) Weight Maximum configuration as shipped: 7.5 kg (16.53 lbs) Enironment Air temperature: Operating: 10 to 35 C (50 to 95 F) Non-operating: -40 to 60 C (-40 to 140 F) (with package) Non-operating: -10 to 60 C (14 to 140 F) (without package) Humidity: Operating: 10% to 80% (10% per hour, non condensing) Non-operating: 10% to 90% (10% per hour, non condensing) Maximum altitude: Operating: -50 to ft (-15.2 to m) Non-operating: -50 to ft (-15.2 to m) Electrical input Input oltage: Low range: Minimum: 100 V ac Maximum: 127 V ac Input frequency range: 50 to 60 Hz Voltage-selection switch setting: 115 V ac High range: Minimum: 200 V ac Maximum: 240 V ac Input frequency range: 50 to 60 Hz Voltage-selection switch setting: 230 V ac 4 User Guide

13 Software oeriew The computer comes with a preinstalled operating system and seeral preinstalled applications. Software proided with your Windows operating system This section describes the Windows applications proided with your computer. Software proided by Lenoo The following software programs are proided by Lenoo to help you improe productiity and reduce the cost associated with maintaining your computer. Software programs proided with your computer might ary depending on your model type and preinstalled operating system. Lenoo ThinkVantage Tools: The Lenoo ThinkVantage Tools program guides you to a host of information sources and proides easy access to arious tools to help you work more easily and securely. For more information, see Lenoo ThinkVantage Tools on page 63. Note: The Lenoo ThinkVantage Tools program is only aailable on computers preinstalled with Windows 7 from Lenoo. Lenoo Care: The Lenoo Care SM program guides you to a host of information and tools to help you set up, understand, maintain, and enhance your computer. For more information, see Lenoo Care on page 63. Note: The Lenoo Care program is only aailable on computers preinstalled with Windows Vista or Windows XP from Lenoo. Lenoo Welcome: The Lenoo Welcome program introduces some innoatie built-in features of Lenoo to you and guides you through some important setup tasks to help you make the most of your computer. Note: The Lenoo Welcome program is only aailable on computers preinstalled with Windows 7 or Windows Vista from Lenoo. Product Recoery: The Product Recoery program enables you to restore the contents of the hard disk drie to the factory default settings. ThinkVantage Rescue and Recoery: The ThinkVantage Rescue and Recoery (RnR) program is a one button recoery and restore solution that includes a set of self-recoery tools to help you diagnose computer problems, get help, and recoer from system crashes quickly, een if the primary operating system could not start. Password Manager: The Password Manager program helps you automatically capture and fill in authentication information for Windows applications and Web sites. ThinkVantage System Update: The ThinkVantage System Update (TVSU) program helps you keep the software on your system up-to-date by downloading and installing software packages (TVT applications, deice driers, BIOS flashes, and other third party applications). Some examples of software that you should keep updated are programs proided by Lenoo, such as the ThinkVantage Rescue and Recoery program and the Lenoo Care program. Chapter 1. Product oeriew 5

14 ThinkVantage Power Manager: The ThinkVantage Power Manager program proides conenient, flexible, and complete power management for your ThinkCentre computer. By using the ThinkVantage Power Manager program, you can adjust your power settings to achiee the best balance between system performance and power saing. Fingerprint software: The integrated fingerprint reader proided on some keyboards enables you to enroll your fingerprint and associate it with your power-on password, hard disk drie password, and Windows password. As a result, fingerprint authentication can replace passwords and enable simple and secure user access. A fingerprint reader keyboard is aailable with select computers or can be purchased for computers that support this option. Lenoo ThinkVantage Toolbox The Lenoo ThinkVantage Toolbox program helps you maintain your computer, improe computing security, diagnose computer problems, get familiar with the innoatie technologies proided by Lenoo, and get more information about your computer. See Lenoo ThinkVantage Toolbox on page 59 for detailed information. Note: The Lenoo ThinkVantage Toolbox program is only aailable on computers preinstalled with Windows 7 from Lenoo. Lenoo System Toolbox The Lenoo System Toolbox diagnostic program is preinstalled on your hard disk drie. This diagnostic program works through the Windows operating system to diagnose hardware problems and report operating-system-controlled settings that can cause hardware failures. See Lenoo System Toolbox on page 59 for more information. Note: The Lenoo System Toolbox program is only aailable on computers preinstalled with Windows Vista or Windows XP from Lenoo. PC-Doctor for Rescue and Recoery The PC-Doctor for Rescue and Recoery diagnostic program is preinstalled on your hard disk drie. It is part of the Rescue and Recoery workspace on each Lenoo computer to diagnose hardware problems and report operating-systemcontrolled settings that can cause hardware failures. Use the PC-Doctor for Rescue and Recoery if you are unable to start the Windows operating system. See PC-Doctor for Rescue and Recoery on page 59 for more information. Adobe Reader The Adobe Reader is a tool used to iew, print, and search PDF documents. See Online Books folder on page 63 for more information about accessing the online books and the Lenoo Web site. Antiirus software Your computer comes with antiirus software that you can use to detect and eliminate iruses. Lenoo proides a full ersion of antiirus software on your hard disk drie with a free 30-day subscription. After 30 days, you must renew the license to continue receiing the antiirus program updates. For more information about updating your antiirus software, refer to the Access Help. See Access Help on page 64 for instructions on how to open the help system. 6 User Guide

15 Locations Locating connectors on the front of your computer Figure 1 shows the locations of the connectors on the front of your computer. Note: Not all computer models hae the following connectors. Figure 1. Front connector locations 1 USB connector 2 Headphone connector 3 Microphone connector 4 USB connector Chapter 1. Product oeriew 7

16 Locating connectors on the rear of your computer Figure 2 shows the locations of the connectors on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer. Figure 2. Rear connector locations 1 Serial port (some models) 8 USB connectors (4) 2 Power cord connector 9 Ethernet connector 3 Standard mouse connector 10 Microphone connector 4 Standard keyboard connector 11 Audio line-out connector 5 Serial port 12 Audio line-in connector 6 Parallel port 13 PCI Express x16 graphics card slot 7 VGA monitor connector 14 PCI card slot 8 User Guide

17 Connector Description Audio line-in connector Used to receie audio signals from an external audio deice, such as a stereo system. When you attach an external audio deice, a cable is connected between the audio line-out connector of the deice and the audio line-in connector of the computer. Audio line-out connector Used to send audio signals from the computer to external deices, such as powered stereo speakers (speakers with built-in amplifiers), headphones, multimedia keyboards, or the audio line-in connector on a stereo system or other external recording deices. Ethernet connector Used to attach an Ethernet cable for a local area network (LAN). Note: To operate the computer within FCC Class B limits, use a Category 5 Ethernet cable. Microphone connector Used to attach a microphone to your computer when you want to record sound or if you use speech-recognition software. Parallel port Used to attach a parallel printer, a parallel scanner, or other deices that use a 25-pin parallel port. Standard keyboard connector Used to attach a keyboard that uses a standard keyboard connector. Standard mouse connector Used to attach a mouse, a trackball, or other pointing deices that use a standard mouse connector. Serial port USB connector Used to attach an external modem, a serial printer, or other deices that use a 9-pin serial port. Used to attach a deice that requires a Uniersal Serial Bus (USB) connector, such as a USB keyboard, a USB mouse, a USB scanner, or a USB printer. If you hae more than six USB deices, you can purchase a USB hub, which you can use to connect additional USB deices. VGA monitor connector Used to attach a VGA monitor or other deices that use a VGA monitor connector. Chapter 1. Product oeriew 9

18 Locating components Figure 3 shows the locations of the arious components in your computer. To open the computer coer, see Opening the computer coer on page 14. Figure 3. Component locations 1 Hard disk drie 4 Optical drie 2 Heat sink and fan assembly 5 Memory slots (2) 3 Internal speaker (some models) 6 Power supply assembly 10 User Guide

19 Locating parts on the system board Figure 4 shows the locations of the parts on the system board. Figure 4. System board parts locations 1 PCI card slot 11 Memory slots (2) 2 PCI Express x16 graphics card slot 12 Front USB connectors (2) 3 Internal speaker connector 13 Serial (COM 2) connector 4 Battery 14 Power fan connector 5 Microprocessor fan connector pin power connector 6 Thermal sensor connector 16 SATA connectors (2) 7 Coer presence switch connector (Intrusion switch connector) (some 17 Clear CMOS (Complementary Metal Oxide Semiconductor)/Recoery jumper models) 8 Microprocessor 18 Front audio connector 9 4-pin power connector 19 System fan connector (some models) 10 Front panel connector Chapter 1. Product oeriew 11

20 12 User Guide

21 Chapter 2. Installing options and replacing hardware This chapter proides instructions for installing options and replacing hardware for your computer. You can expand the capabilities of your computer by adding dries, memory modules, or PCI cards. When installing or replacing an option, use these instructions along with the instructions that come with the option. Important: Before you install or replace any option, be sure to read and understand the Important safety information in the ThinkCentre Safety and Warranty Guide. The precautions and guidelines will help you work safely. Handling static-sensitie deices Do not open the static-protectie package containing the new part until the defectie part has been remoed from the computer and you are ready to install the new part. Static electricity, although harmless to you, can seriously damage computer components and parts. When you handle parts and other computer components, take these precautions to aoid static-electricity damage: Limit your moement. Moement can cause static electricity to build up around you. Always handle parts and other computer components carefully. Handle PCI cards, memory modules, system boards, and microprocessors by the edges. Neer touch any exposed circuitry. Preent others from touching the parts and other computer components. Before you replace a new part, touch the static-protectie package containing the part to a metal expansion-slot coer or other unpainted metal surface on the computer for at least two seconds. This reduces static electricity in the package and your body. When possible, remoe the new part from the static-protectie packaging, and install it directly in the computer without setting the part down. When this is not possible, place the static-protectie package that the part came in on a smooth, leel surface and place the part on it. Do not place the part on the computer coer or other metal surface. Installing options and replacing hardware This section proides introductions for installing options and replacing hardware for your computer. When installing or replacing an option, use these instructions along with the instructions that come with the option. Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: Note: Use only computer parts proided by Lenoo. Copyright Lenoo

22 Installing external options External speakers, a printer, or a scanner can be connected to your computer. For some external options, you must install additional software in addition to making the physical connection. When installing an external option, see Locating connectors on the front of your computer on page 7 and Locating connectors on the rear of your computer on page 8 to identify the required connector, and then use the instructions that come with the option to help you make the connection and install any software or deice driers that are required for the option. Opening the computer coer Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to open the computer coer. CAUTION: Turn off the computer and wait three to fie minutes to let the computer cool before opening the computer coer. To open the computer coer: 1. Remoe any media from the dries, shut down your operating system, and turn off all attached deices and the computer. 2. Unplug all power cords from electrical outlets. 3. Disconnect the cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. See Locating connectors on the front of your computer on page 7 and Locating connectors on the rear of your computer on page Remoe any locking deices, such as a cable lock that secures the computer coer. 14 User Guide

23 5. Press the buttons on the sides of the computer and piot the computer coer upward to open. Figure 5. Opening the computer coer Chapter 2. Installing options and replacing hardware 15

24 Accessing the system board components and dries This section proides instructions on how to access the system board components and dries. To access the system board components and dries: 1. Open the computer coer. See Opening the computer coer on page On some models, you might need to piot the drie bay assembly upward and remoe the hard disk drie to access the internal components. See Replacing the hard disk drie on page 24. Note: Make sure you note the locations of any cables that you disconnect from the dries or the system board. Attention: Make sure the hard disk drie assembly is in the latched down position before closing the computer coer to preent damage to the hard disk drie assembly. Figure 6. Pioting the drie bay assembly Installing or replacing a memory module Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to install or replace a memory module. Your computer has two slots for installing or replacing DDR2 DIMMs. When installing or replacing a memory module, use 1 GB or 2 GB DDR2 DIMMs in any combination up to a maximum of 4 GB system memory. 16 User Guide

25 To install or replace a memory module: 1. Open the computer coer. See Opening the computer coer on page Piot the drie bay assembly upward to access the memory slots. See Accessing the system board components and dries on page Remoe any parts that might preent your access to the memory slots. 4. Locate the memory slots. 5. Open the retaining clips. Figure 7. Opening the retaining clips If you are replacing an old memory module, open the retaining clips and remoe the memory module being replaced as shown. Figure 8. Remoing the old memory module Chapter 2. Installing options and replacing hardware 17

26 6. Position the memory module oer the memory slot. Make sure that the notch 1 on the memory module aligns correctly with the slot key 2 on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 9. Installing the memory module What to do next: To work with another option, go to the appropriate section. To complete the installation, go to Completing the parts replacement on page 37. Installing or replacing a PCI card Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to install or replace a PCI card. Your computer has one standard PCI card slot and one PCI Express x16 graphics card slot. To install or replace a PCI card: 1. Open the computer coer. See Opening the computer coer on page Rotate the card retainer to the open position. 3. Remoe the new PCI card from its static-protectie package. 18 User Guide

27 4. Install the new card into the appropriate card slot on the system board. See Locating parts on the system board on page 11. If you are replacing an old PCI card, remoe the old card currently installed before installing the new one. Figure 10. Remoing the old card Notes: a. The card fits tightly into the card slot. If necessary, alternately moe each side of the card a small amount until it is fully remoed from the card slot. b. If the card is held in place by a retaining latch, press the card retaining latch 1 as shown to disengage the latch. Grasp the card and gently pull it out of the slot. Chapter 2. Installing options and replacing hardware 19

28 5. Rotate the card retainer to the closed position. Figure 11. Installing the card What to do next: To work with another option, go to the appropriate section. To complete the installation, go to Completing the parts replacement on page 37. Installing internal dries This section proides instructions on how to install the internal dries. Internal dries are deices that your computer uses to read and store data. You can add dries to your computer to increase storage capacity and enable your computer to read other types of media. Some of the types of dries that are aailable for your computer are: Serial Adanced Technology Attachment (SATA) hard disk dries SATA optical dries, such as CD dries or DVD dries Remoable media dries Note: These types of dries are also referred to as integrated drie electronics (IDE) dries. Internal dries are installed in bays. In this manual, the bays are referred to as bay 1, bay 2, and so on. When you install an internal drie, it is important to note the type and size of the drie that you can install in each bay. Also, it is important to correctly connect the internal drie cables to the installed drie. 20 User Guide

29 Drie specifications Your computer comes with the following factory-installed dries: A 3.5-inch hard disk drie in bay 1 An optical drie in bay 2 (some models) Figure 12 shows the locations of the drie bays. Figure 12. Drie bay locations The following list describes the type and size of the drie that you can install in each bay: 1 Bay 1 - Maximum height: 25.8 mm (1 inch) 2 Bay 2 - Maximum height: 43.0 mm (1.7 inches) Maximum length: 180 mm (7.08 inches) Internal hard disk drie Optical drie, such as a CD drie or a DVD drie (preinstalled in some models) 5.25-inch hard disk drie Chapter 2. Installing options and replacing hardware 21

30 Installing a drie in bay 2 Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to install an optical drie or an additional hard disk drie in bay 2. To install an optical drie or an additional hard disk drie in bay 2: 1. Open the computer coer. See Opening the computer coer on page If there is a metal static shield installed in the drie bay, remoe the metal shield by using a flat-blade screwdrier to gently pry it loose. 3. Install the retainer that comes with your drie on the side of the drie. Figure 13. Installing the retainer 4. Slide the drie into the bay until it locks into position. Figure 14. Installing the drie 5. Piot the drie bay assembly upward to gain access to the cable connections and connect the signal cable and the power cable for the drie. 6. Continue at Connecting a SATA drie on page User Guide

31 Connecting a SATA drie A SATA optical drie or a SATA hard disk drie can be connected to any aailable SATA connector. To connect a SATA drie: 1. Locate the signal cable that comes with the new drie. 2. Locate an aailable SATA connector on the system board. See Locating parts on the system board on page Connect one end of the signal cable to the drie and the other end to the aailable SATA connector on the system board. 4. Locate one of the extra fie-wire power connectors and connect it to the drie. Figure 15. Connecting a SATA drie What to do next: To work with another option, go to the appropriate section. To complete the installation, go to Completing the parts replacement on page 37. Chapter 2. Installing options and replacing hardware 23

32 Replacing the hard disk drie Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to replace the hard disk drie. Important When you receie a new hard disk drie, you also receie a set of Product Recoery discs. The set of Product Recoery discs enables you to restore the contents of the hard disk drie to the factory default settings. For more information on recoering factory-installed software, refer to Chapter 3, Recoery information, on page 41. To replace the hard disk drie: 1. Open the computer coer. See Opening the computer coer on page You might need to piot the drie bay assembly upward to gain easy access to the hard disk drie. 3. Locate the hard disk drie. 4. Push the blue handle of the hard disk drie bracket inwards to release the two clips 1 that secure the hard disk drie to the chassis, and then rotate the hard disk drie upwards and lift it up to remoe it from the computer. Figure 16. Remoing the hard disk drie 5. Disconnect the signal cable and the power cable from the hard disk drie. 24 User Guide

33 6. Remoe the old hard disk drie from the bracket by flexing the sides of the bracket enough to slide it free from the hard disk drie. Figure 17. Remoing the hard disk drie from the bracket 7. To install a new hard disk drie into the bracket, flex the bracket and align pin 1, pin 2, pin 3, and pin 4 on the bracket with the holes in the hard disk drie. Important: Do not touch the circuit board on the bottom of the hard disk drie. 8. Connect the signal cable and the power cable to the new hard disk drie. 9. Install the new hard disk drie and bracket into the rear retainer and rotate down until the two clips on the blue handle of the hard disk drie bracket snap into position. 10. Go to Completing the parts replacement on page 37. Chapter 2. Installing options and replacing hardware 25

34 Replacing the optical drie Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to replace the optical drie. To replace the optical drie: 1. Open the computer coer. See Opening the computer coer on page Piot the drie bay assembly upward to gain access to the optical drie. See Accessing the system board components and dries on page Disconnect the signal cable and the power cable from the rear of the optical drie. 4. Press the optical drie lock 1 and slide the optical drie out the rear of the drie bay assembly. Figure 18. Remoing the old optical drie 5. Remoe the optical drie retainer from the old optical drie and then install it on the side of the new optical drie. Figure 19. Installing the retainer 26 User Guide

35 6. Slide the new optical drie into the bay until it snaps into position. Figure 20. Installing the new optical drie 7. Connect the signal and power cables to the rear of the optical drie. 8. Go to Completing the parts replacement on page 37. Replacing the battery Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to replace the battery. Your computer has a special type of memory that maintains the date, time, and settings for built-in features, such as parallel-port assignments (configuration). A battery keeps this information actie when you turn off the computer. The battery normally requires no charging or maintenance throughout its life; howeer, no battery lasts foreer. If the battery fails, the date, time, and configuration information (including passwords) are lost. An error message is displayed when you turn on the computer. Refer to the Lithium battery notice in the ThinkCentre Safety and Warranty Guide for information about replacing and disposing of the battery. To replace the battery: 1. Open the computer coer. See Opening the computer coer on page Locate the battery. See Locating parts on the system board on page 11. Chapter 2. Installing options and replacing hardware 27

36 3. Remoe the old battery. Figure 21. Remoing the old battery 4. Install a new battery. Figure 22. Installing a new battery 5. Reinstall the computer coer and connect the cables. See Completing the parts replacement on page 37. Note: When the computer is turned on for the first time after replacing the battery, an error message might be displayed. This is normal after replacing the battery. 6. Turn on the computer and all attached deices. 7. Use the Setup Utility program to set the date, time, and any passwords. See Chapter 4, Using the Setup Utility, on page User Guide

37 Replacing the power supply assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to replace the power supply assembly. To replace the power supply assembly: 1. Remoe the four screws at the rear of the chassis that secure the power supply assembly. Figure 23. Remoing the retaining screws for the power supply assembly 2. Open the computer coer. See Opening the computer coer on page Piot the drie bay assembly upward to gain access to the power supply assembly. 4. Locate the power supply assembly. See Locating components on page 10. Chapter 2. Installing options and replacing hardware 29

38 5. Disconnect the power supply assembly cables from all dries and from the power connectors 1 and 2. Note: You might need to remoe the hard disk drie to gain easy access to the power connector 1. See Replacing the hard disk drie on page 24. Figure 24. Power connectors on the system board 6. Remoe the power supply assembly cables from the cable clips and ties. 7. Slide the power supply assembly away from the chassis and remoe it from the computer. Figure 25. Remoing the power supply assembly 30 User Guide

39 8. Install the new power supply assembly into the chassis so that the screw holes in the new power supply assembly align with those in the chassis. 9. Install and tighten the four screws at the rear of the chassis to secure the power supply assembly. Note: Use only the screws proided by Lenoo. 10. Reconnect all the power supply assembly cables to the dries and the system board. 11. Go to Completing the parts replacement on page 37. Replacing the heat sink and fan assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to replace the heat sink and fan assembly. CAUTION: The heat sink and fan assembly might be ery hot. Turn off the computer and wait three to fie minutes to let the computer cool before opening the computer coer. To replace the heat sink and fan assembly: 1. Open the computer coer. See Opening the computer coer on page Piot the drie bay assembly upward to gain access to the heat sink and fan assembly. See Accessing the system board components and dries on page Locate the heat sink and fan assembly and disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system board. See Locating parts on the system board on page 11. Chapter 2. Installing options and replacing hardware 31

40 4. Remoe the heat sink and fan assembly from the system board by pioting the leer 1 that secures the heat sink and fan assembly until it is fully in the up position. Carefully lift the heat sink and fan assembly off the system board. Notes: a. You might hae to gently twist the heat sink and fan assembly to free it from the microprocessor. b. Do not touch the thermal grease while handling the heat sink and fan assembly. Figure 26. Remoing the heat sink and fan assembly 5. Place the new heat sink and fan assembly into position and lower the leer to secure the new heat sink and fan assembly. 6. Connect the new heat sink and fan assembly cable to the microprocessor fan connector on the system board. 7. Go to Completing the parts replacement on page User Guide

41 Replacing the microprocessor Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to replace the microprocessor. CAUTION: The heat sink and microprocessor might be ery hot. Turn off the computer and wait three to fie minutes to let the computer cool before opening the computer coer. To replace the microprocessor: 1. Open the computer coer. See Opening the computer coer on page Piot the drie bay assembly upward to gain access to the system board. See Accessing the system board components and dries on page Locate the heat sink and fan assembly and disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system board. See Locating parts on the system board on page Remoe the heat sink and fan assembly. See Replacing the heat sink and fan assembly on page Place the heat sink and fan assembly on its side so that the thermal grease does not come in contact with anything. 6. Remoe the hard disk drie. See Replacing the hard disk drie on page Lift the small handle 3 and open the retainer 1 to access the microprocessor 2. Chapter 2. Installing options and replacing hardware 33

42 8. Lift the microprocessor straight up and out of the socket. Notes: a. Your microprocessor and socket might look different from the one illustrated. b. Note the orientation of the microprocessor in the socket. You can either look for the small triangle 1 on one corner of the microprocessor or note the orientation of the notches 2 on the microprocessor. This is important when installing the new microprocessor on the system board. c. Touch only the sides of the microprocessor. Do not touch the gold contacts on the bottom. d. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. 9. Make sure that the small handle is in the raised position. 34 User Guide

43 10. Remoe the protectie coer 2 that protects the gold contacts on the new microprocessor Hold the new microprocessor and align the notches on it with the tabs in the microprocessor socket, or align the small triangle on one corner with the corresponding beeled corner of the microprocessor socket. 12. Lower the new microprocessor straight down into the microprocessor socket on the system board. 13. Close the microprocessor retainer and lock it into position with the small handle to secure the new microprocessor in the socket. 14. Reinstall the hard disk drie. See Replacing the hard disk drie on page Reinstall the heat sink and fan assembly. See Replacing the heat sink and fan assembly on page Reconnect the heat sink and fan assembly cable to the microprocessor fan connector on the system board. 17. Go to Completing the parts replacement on page 37. Chapter 2. Installing options and replacing hardware 35

44 Replacing the keyboard Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: This section proides instructions on how to replace the keyboard. To replace the keyboard: 1. Remoe any media from the dries, shut down your operating system, and turn off all attached deices and the computer. 2. Unplug all power cords from electrical outlets. 3. Locate the keyboard connector. Note: Your keyboard might be connected to a standard keyboard connector 1 or a USB connector 2. Depending on where your keyboard is connected, see Locating connectors on the rear of your computer on page 8 or Locating connectors on the front of your computer on page 7. Figure 27. Keyboard connectors 4. Disconnect the failing keyboard cable from the computer. 5. Connect a new keyboard to the appropriate connector on the computer. 6. Go to Completing the parts replacement on page 37. Replacing the mouse Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: 36 User Guide This section proides instructions on how to replace the mouse. To replace the mouse: 1. Remoe any media from the dries, shut down your operating system, and turn off all attached deices and the computer.

45 2. Unplug all power cords from electrical outlets. 3. Locate the connector for the mouse. Note: Your mouse might be connected to a standard mouse connector 1 or a USB connector 2. Depending on where your mouse is connected, see Locating connectors on the rear of your computer on page 8 or Locating connectors on the front of your computer on page 7. Figure 28. Mouse connectors 4. Disconnect the failing mouse cable from the computer. 5. Connect a new mouse cable to the appropriate connector on the computer. 6. Go to Completing the parts replacement. Completing the parts replacement After completing all parts replacements, you need to reinstall the computer coer and reconnect cables, such as the power cords. Depending on the parts replaced, you might need to confirm the updated information in the Setup Utility program. Refer to Chapter 4, Using the Setup Utility, on page 49. To close the computer coer and reconnect cables to your computer: 1. Ensure that all components hae been reassembled correctly and that no tools or loose screws are left inside your computer. See Locating components on page 10 for the locations of arious components. Chapter 2. Installing options and replacing hardware 37

46 2. Ensure that the cables are routed correctly before lowering the drie bay assembly. Important Correctly route all power supply cables to aoid interference with the drie bay assembly. Keep cables clear of the hinges and sides of the computer chassis. Figure 29. Cable routing 3. Lower the drie bay assembly and place the drie locks to the locked position. Otherwise, you cannot close the computer coer. 4. If you remoed the front bezel, reinstall it by aligning the three tabs on the front bezel with the corresponding holes on the chassis and pioting the front bezel inward until it snaps into position. 5. Close the computer coer. 6. If a computer coer lock is installed, lock the computer coer. 7. Reconnect the external cables and power cords to the computer. See Locating connectors on the rear of your computer on page To update your configuration, see Chapter 4, Using the Setup Utility, on page 49. Note: In most areas of the world, Lenoo requires the return of the defectie CRU. Information about this will come with the CRU or will come a few days after the CRU arries. Obtaining deice driers You can obtain deice driers for operating systems that are not preinstalled at: Installation instructions are proided in readme files with the deice-drier files. 38 User Guide

47 Installing security features To help preent hardware theft and unauthorized access to your computer, seeral security options are aailable. In addition to physical locks, unauthorized use of your computer can be preented by a software lock that locks the keyboard until a correct password is typed in. Make sure that any security cables you installed do not interfere with other computer cables. Integrated cable lock An integrated cable lock (sometimes referred to as the Kensington lock), can be used to secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to a security slot at the rear of your computer and is operated with a key. The cable lock also locks the buttons used to open the computer coer. This is the same type of lock used with many notebook computers. You can order a security cable directly from Lenoo by searching on Kensington at: Figure 30. Integrated cable lock Password protection To deter unauthorized use of your computer, you can use the Setup Utility program to set a password. When you turn on your computer, you are prompted to type the password to unlock the keyboard for normal use. Refer to Chapter 4, Using the Setup Utility, on page 49 for more information. Chapter 2. Installing options and replacing hardware 39

48 What to do next: To work with another option, go to the appropriate section. To complete the installation, go to Completing the parts replacement on page 37. Erasing lost or forgotten passwords (clearing CMOS) This section contains instructions on erasing lost or forgotten passwords, such as a user password. To erase lost or forgotten passwords: 1. Open the computer coer. See Opening the computer coer on page Locate the Clear CMOS/Recoery jumper on the system board. See Locating parts on the system board on page Moe the jumper from the standard position (pin 1 and pin 2) to the maintenance or configure position (pins 2 and pin 3). 4. Close the computer coer and connect the power cord. See Completing the parts replacement on page Restart the computer, leae it on for approximately 10 seconds, and then turn off the computer by holding the power switch for approximately fie seconds. 6. Repeat step 1 and step Moe the Clear CMOS/Recoery jumper back to the standard position (pin 1 and pin 2). 8. Close the computer coer and connect the power cord. See Completing the parts replacement on page User Guide