T8xC5121 Starter Kit... User Guide

Transcription

1 T8xC Starter Kit... User Guide

2

3 Section Introduction Features...- Section Getting Started Package Contents...-. PC System Requirements...-. Quick Start...-. Connecting the Microcontroller...-. Hardware Connection Power Supply...- Section Hardware Description Description of Jumpers Description of Switches Reset Clock EA Switch INT Switch Serial Port LEDs Smart Card Interface SIM Card Interface...-0 Section Microcontroller Programming FLIP Software...-. Programming the T89C...-. Programming the T8C...- Section Software Description Programming Using FLIP...-. Running the Demonstration Program...-7 Section 6 Appendix A Schematics References Acronyms...-6 T8xC Starter Kit User Guide

4

5 Section Introduction The T8xC Starter Kit allows you to fully evaluate the T8xC microcontrollers. You can run either the included demonstration program or your own application. The board can also be used as a programmer for the T89C product. The T8xC Demonstration Board supports communication through RS- serial communication mode. This user s guide describes the hardware of the Demonstration Board as well as documentation about the demonstration software.. Features The Demonstration Board Contains Either: Stand-alone Mode With the On-chip EEPROM Program Memory (T89C Product Version) or, On-board EEPROM Program Memory In-System Programmable (ISP) via the ROM Bootloader that Downloads HEX Files Into Internal RAM Memory Smart Card Connector SIM Connector LEDS On-board Voltage Regulator with Voltage Setting Sockets: SSOP, DIL for Package Adapter RS- Serial Port Interrupt (INT) Input Manual Reset Switch Data, Address and Control Lines Conveniently Brought Out on Connectors Prototyping Area T8xC Starter Kit User Guide - Rev.

6 Introduction Figure. T8xC Starter Kit - T8xC Starter Kit User Guide

7 Section Getting Started. Package Contents n T8xC Demonstration Board n T8C and T89C Microcontrollers n MPCOS EMV smart card n SSOP Adapter n CD-ROM with Software and Documentation FLIP software for In-System Programming Quickterm Software for Demonstration Note: A direct serial cable (DB9) and a power supply are not provided.. PC System Requirements n 86 processor n 6 MB RAM n MB Free disk Space n Windows 98, Windows NT, XP or Windows 000. Quick Start The T8xC D Starter Kit is shipped with a T8C and T89C microcontroller. The demonstration board and accompanying software allow you to read data from a smartcard and display it on a host PC. You can also load your own application (in.hex file format) to retrieve data from a smartcard or a credit card.. Connecting the Microcontroller The T8xC Demonstration Board is designed to support two different microcontrollers, T8C and T89C. The microcontrollers are connected either on the bottom or top of the board, respectively. The T89C requires the use of the SSOP Adapter which must be plugged into the DIL support. Alternatively, the T89C can be soldered on the board. T8xC Starter Kit User Guide - Rev.

8 Figure -. T8xC Demonstration Board with T89C Microcontroller (Top View) Figure -. T8xC Demonstration Board with T8C Microcontroller (Bottom View)

9 Getting Started. Hardware Connection. A 9 - V power supply must be connected to the J connector.. A serial cable must first be attached between COM PC port and J DB9 connector of the demonstration board.. Ensure the T89C or the T8C microcontroller is connected to the board.. The ON/OFF Switch (SW) must be ON. See Figure -. The Board is delivered with one.76 MHz quartz (Y)..6 Power Supply.6. Board Supply The Board can be powered from: n 9V DC IN J Power connector n 9V DC IN JR connector for battery connection n - V DC IN JH connector connected to V CC /V SS Signals n RS- Connector using Pin 9 and JP Connector In the first two configurations the potentiometer R is used to adjust the V CC level. In the last two configurations V CC is directly connected to the board. Table - outlines the isolated Power Supply control for the demonstration board and microcontroller. Table -. Power Supply Control Settings Reference Designation Switch On/Off Test Point Jumpers Function Vcc Product Power Supply SW TP JP Global Vcc Vcc Microcontroller Power Supply JP7 MCU Vcc.6. Internal Voltages Three test points are provided to monitor the internal voltages. Table -. Test Points Table Reference Designation Test Point DVCC Core regulated voltage (V) TP EVCC UART power supply TP0 CVCC Smart Card Supply TP T8xC Starter Kit User Guide -

10 Getting Started -6 T8xC Starter Kit User Guide

11 Section Hardware Description Figure -. T8xC Demonstration Board Components SW JP JP7 SSOP JP6 JP DIL PLCC Socket () Y JP JP JP LED LED Smart Card Slot U JP JP JP JP8 JP JP9 JP8 JP JP9 JP7 SW Reset JP6 Note:. On solder side. T8xC Starter Kit User Guide -7 Rev.

12 Hardware Description. Description of Jumpers The following table sums up the configuration jumpers available on the board. Their location is detailed in Figure -. Table -. Configuration Jumpers Reference Type Designation Configuration Function JP Jumper Board Vcc ON Demonstration board V CC Jumper JP Solder P. ON External IC SDA = P. (..0 Bootloader): Default Configuration JP Solder V CC PC Demonstration board V CC power from RS Connection JP Solder P. External IC SCL = P. (.0. Bootloader) JP Jumper Rx ON Isolate MAX to test EVCC control JP6 Jumper Tx ON Isolate MAX to test EVCC control JP7 Jumper R+ CPRES Connect external CPRES pull-up resistor (internal by default) JP8 Jumper + CPRES V CC CPRES connection (CPRES high level detect) JP9 Jumper - CPRES ON V SS CPRES connection JP Jumper RST ON Isolate External Reset Switch JP Jumper LED0 ON Isolate LED0 JP Jumper LED ON Isolate LED JP Jumper R- CPRES Connect external pull-down resistor (CPRES high level detect) JP6 Jumper Vpp Card Vpp option connected to V CC JP7 Jumper MCU Vcc ON Microcontroller V CC Jumper JP8 Solder P.7 ON External IC SCL=P.7 (..0 Bootloader): Default Configuration JP9 Solder CLK EXT External Clock connected to XTAL JP Solder P. External IC SDA=P. (.0. Bootloader). Description of Switches The following table sums up the switches available on the board. Their location is detailed in Figure -. Table -. Switches Reference Designation Function SW RESET External Reset pushbutton SW ON/OFF Board ON/OFF Switch SW Smart Card Reader Connector SW INT INT pushbutton SW6 EA/INT - EA switch = 0 or - INT switch to enable/disable INT pushbutton SW7 CPRES Optional CPRES manual switch -8 T8xC Starter Kit User Guide

13 Hardware Description. Reset The on-chip Power-on Reset function generates an internal Reset at power-up. The external reset push button is provided to easily generate a warm reset during the ISP process. See Figure -.. Clock Crystal can be installed on the Y socket. To use an external Clock, the input must connected to the optional J connector and a jumper must be placed at JP9. See Figure -.. EA Switch EA switch inside the SW6 Dip switch is by default connected to Vcc. Figure -. Default Configuration: switches opened SW6 0 EA EA= INT INT switch opened.6 INT Switch The INT configuration switch (SW6 dip switch) selects whether or not the INT push button is connected to port pin P. on the microcontroller. See Figure -..7 Serial Port The Board supports a MAX at U (See Figure -) to convert RS- voltage levels. The serial I/O P.0/RXD, P./TXD can be disconnected using the JP, JP6 jumpers..8 LEDs The JP and JP jumpers placed in series with the LED0 and LED can be used to monitor the LED current or to disconnect the LEDs..9 Smart Card Interface.9. Card Detection Card detection, by default, uses the on-chip internal pull-up register and the jumper JP9 connected to Vss. This configuration detects the low level input. Another configuration can be used to detect a high level input when the card is inserted. This is done using the jumpers JP8 and JP. In this case, it is necessary to first disconnect the internal pull-up resistor, using accompanying software. See Section Software Description. T8xC Starter Kit User Guide -9

14 Hardware Description.9. Card I/O The following test points are provided to monitor the Smart Card I/O signals: Table -. Smart Card I/O Signals Test Points Reference Designation Test Point CVCC Card power supply TP CRST Card Reset TP CCLK Card Clock TP CIO Card I/O TP CVSS Card power ground TP6 The JP6 Jumper can be used to connect VPP to the card..0 SIM Card Interface The following test points are provided to monitor the SIM Card I/O signals: Table -. SIM Card I/O Test Points Reference Designation Test Point CRST Card Reset TP7 CCLK Card Clock TP8 CIO Card I/O TP9-0 T8xC Starter Kit User Guide

15 Section Microcontroller Programming The CD-ROM includes: n The demonstration software designed to read cards n The software tool for ISP: FLIP (Flexible In-system Programmer) n The terminal software: Quickterm - to interface the card access on host n The SCI library including software drivers in C language. FLIP Software FLIP is software that runs on Windows 98, Windows NT, XP or Windows 000. FLIP supports in-system programming of Flash C devices through RS. The latest version of FLIP software can be found on the Atmel web site, Programming the T89C.. Programming from External EEPROM Source The on-chip internal EEPROM of the T89C version can be programmed using either: n External EEPROM Atmel ATC8 n Serial RS- After Reset, if an ATC8 EEPROM has been detected at U (see Figure -), the on-chip ROM Bootloader downloads the external EEPROM content (6K bytes) in the on-chip EEPROM and in the Code RAM. Figure -. EEPROM at U of Demonstration Board T8xC Starter Kit User Guide - Rev.

16 Microcontroller Programming When the download is achieved, the Bootloader runs the program. This process duration is 7. seconds at.76 MHz. Figure -. Bootloader Diagram T89C External Serial EEPROM ATC8 TWI Internal on-chip EEPROM Code RAM 6K bytes.. Programming from RS- source As specified in the T8xC datasheet, the two highest addresses of the 6K bytes code must contain the program CRC and the bootloader compares with computed CRC to launch (or not) the program execution. The CRC value can be calculated with FLIP Software: the user must load the Hex file and press the button: CRC. The updated buffer can then be saved as a new Hex file including the two CRC bytes. CAUTION: The Jumper JP (LED) must be removed. Otherwise the TWI Clock signal will not be at the correct levels. A serial cable must first be attached between COM PC port and J DB9 connector of the Demonstration board. After Reset, if a ATC8 EEPROM has not been detected at U, the on-chip ROM Bootloader tests if the UART receives U (0x) characters. Then, commands can be sent to the microcontroller, using FLIP software. The programming sequence is detailed in Section. When the Program command is processed, the Internal EEPROM is programmed at the same time as CRAM. The program execution can be launched from FLIP (RUN Application Button). Figure -. Serial Programming Diagram T89C External Serial EEPROM C8 Internal on-chip EEPROM Code RAM 6K bytes RS- J - T8xC Starter Kit User Guide

17 Microcontroller Programming.. Using Preprogrammed Parts If neither ATC8 External EEPROM nor RS- programming has been detected, the on-chip ROM Bootloader downloads the internal EEPROM content (6K bytes) in the Code RAM and runs the corresponding program. This assumes that, previously, the T89C microcontroller has been programmed. After reset, execution of the program takes seconds at.76 MHz. T89C Internal on-chip EEPROM Code RAM 6K bytes. Programming the T8C The T8C version can be loaded in CRAM with the application program and executed once connected to the Demonstration Board. See Figure -. The processes are the same as for T89C (RS- and External EEPROM) except that there is not an internal EEPROM and so the standalone configuration is not valid. T8xC Starter Kit User Guide -

18 Microcontroller Programming - T8xC Starter Kit User Guide

19 Section Software Description The included demonstration software allows you to:. Program the microcontroller connected to the demonstration board.. Read data from a SmartCard or a Credit Card.. Display the data on the host PC (Quickterm). The demonstration including device programming is described with ISP via RS- communication to host.. Programming Using FLIP This section allows you to program the microcontroller through the RS- cable using FLIP software.. Run FLIP.. From the Device Menu, choose Select and select the device (T8xC) that is connected on your demonstration board. T8xC Starter Kit User Guide - Rev.

20 Software Description. Click the Set Communication button and indicate the COM port settings and Baud Rate. The autobaud feature of the boot loader will configure the device according to the baud rate. Device Selection Set Communication. Initialize the communication by selecting the Connect button in RS pop-up window.. Reset the demonstration board (SW push button) see Figure -. The Rs Communication Synchronized message is displayed at the bottom of the FLIP status window. 6. Load the HEX file. This is the program that performs the demonstration data exchange. In the File menu select Load HEX and choose the demonstration program exchange.hex in the zip file: T8XC_starter/demonstration_soft/t89xc_DemoS 0.zip The message HEX file exchange.hex loading done is displayed at the bottom of the FLIP window. 7. Ensure the following check boxes are selected in the Operations Flow section of FLIP: - Erase - Program - Verify These are the operations that will be performed on the microcontroller. 8. Press the Run button. Programming is executed. The Memory Verify Pass message confirms programming is successful and that the microcontroller has been programmed... Verifying the Application Once programming is complete, press the Start Application button on the FLIP window. The LED0 blinks until a card is introduced. This indicates the device has been programmed. Exit from FLIP. Switch Off the demonstration board. -6 T8xC Starter Kit User Guide

21 Software Description. Running the Demonstration Program.. Running Quickterm PC Software Run Quickterm. Software is located in the zip file: T8XC_starter/demonstration_soft/t89xc_DemoS 0.zip. Execute the quickterm-_0_7.exe file.. In the Quickterm File Menu, select the "Read TRM... command and locate whiteshark.trm file.. Turn On the demonstration board. Note: Help is available in the menu and F can be used to clear the display. For the T89C version, after Reset, LED0 is off during the download of program from EEPROM to Code RAM ( seconds at.76 MHz). When this sequence is achieved, the program is automatically executed and the LED0 blinks again while waiting for a card. The message Insert a card is displayed in the Quickterm window. Figure -. Quickterm Card Reader Window Insert a card into the reader with the chip side facing the bottom of the board, the LED0 turns on. Two types of cards can be read when inserted:. MPCOS-EMV card, use the following sequence to read the serial number of the card: Select a directory (mandatory first command). The response 90 00, indicates that the command has been successful. select a file (mandatory second command) read the serial number The serial number is displayed.. CREDIT card you can choose to read the: name of the card T8xC Starter Kit User Guide -7

22 Software Description end of validity of the card the card number A reset of the reader occurs if the card is removed. To program the chip using a new application load a different HEX file and return to Section.. -8 T8xC Starter Kit User Guide

23 Section 6 Appendix A Figure 6-. Board Components View Diagram T8xC Starter Kit User Guide 6-9 Rev.

24 Appendix A Table 6-. Bill of Materials Table Identifier Designation Qty Radiospares Reference C, C, C, C, C, C Capacitor Tantalum CMS 9D A µf/6v 6 - C8 Capacitor Tantalum CMS 9D B 0µF/0V - C Capacitor Tantalum CMS 9D B 0µF/0V - C0, C7 Capacitor Tantalum CMS 9D B 0µF/0V - C, C, C, C7, C8, C0, Capacitor CMS080 00nF CA, CB, CC C9 Capacitor CMS06 0µF/0V 67-7 C, C6, C, C6 Capacitor CMS080 pf 6-8 C7 Capacitor CMS080 0pF C8 Capacitor CMS080 D Led CMS Red 7-0 D8 Led CMS Red 7-0 D, D Led : Red diameter mm D0 Diode N00 D, D6 Diode N00 JR Connector male Molex -0 J Connector: jack Diam,mm (Power Supply) J Connector SMB -00 J Connector SubD 9pts female J Connector DIN6 Female 9- JH Connector Phoenix MKDS/-,8 0-8 L Coil Murata LQHCNR7M R, R Resistor CMS080 Optional 0 R, Resistor CMS080 00K R Resistor CMS080 00K R7 Resistor CMS080 0K R6, R7 Resistor CMS080 0K R9, R Resistor CMS080 0ohm R Resistor CMS080 K R8 Resistor CMS080 K R Resistor CMS080 0 ohms R Potentiometer K Bourns 96W SW Card reader ITT CCM SW ON/OFF Switch SECME K -68 SW Push-button type KSA trad. SW Push-button type KSA trad. SW7 Push-button type KSA trad. SW6 Dipswitch ways -980 SIM Card reader ITT CCM TP à TP, TP, TP Test points U ATC8 DIP8 U6 ATC8 DIP8 UA PLCC Socket UC DIP Socket U MAXCSE SO6 U7 7HC SO U LM7_ Y Quartz T8xC Starter Kit User Guide

25 Appendix A 6. Schematics Figure 6-. Demonstration Board ( of ) Vcc JP7 J JP9. CA CB CC EA 0 C EA P0.0 P0. D XTAL P0. 0 D P0. 9 Y C6 P0. XTAL P0. 8 P0.6 /RST P P0 ( 7:0 ) RST 9 P.0 8 P./INT0 P. 7 P./INT/OE P./INT0 P. 7 P./T0 P./INT/OE P P./CIO/T P./T0 P. P./CIO/T P. P.0/CIO P.6 8 P./CC8 P.0/CIO P.7 7 P ( 7:0 ) P./CPRES P./CC8 6 P.7/R\D\/CRST/LED P./CCLK P./CC P./CPRES P.7/CRST/RD 9 P.6/W\R\/CCLK/LED0 C P./CRST P./CC P.6/WR 8 PSEN C P./CCLK PSEN 7 ALE P./CRST ALE/ + C9 P./TXD JP D C0 6 P.0/RXD TP0 CVcc VCC CVss ALE R JP6 EVcc EVcc U LI RIN ROUT 8 9 JP C8 RIN ROUT J C TIN TOUT 0 TIN TOUT 7 L TP 9 C C+ 9 TP C- MAX C+ 8 8 C- 7 B DVcc B C V+ 7 6 VCC + V- P./INT/OE 6 6 C7 C VCC VCC + C CONN DSUB 9-Female R7 SW6 Vcc Vss DVcc, Vcc Vss 6 + EA INT_SW6 A A Title T8XC Demonstration Board Size Do c ument Number R e v A..0 Date: Wednesday, December 8, 00 Sheet of T8xC Starter Kit User Guide 6-

26 Appendix A Figure 6-. Demonstration Board ( of ) P./INT/OE JP R VCC 8 VCC optional A0 Vcc JP D A P. D SDA P. VCC JP 7 6 WP SCL ATC8 Vss External JP8 R optional VCC P.7 P. CC VCC U6 CC8 VCC 8 JP6 A0 Vcc TP A SDA C Vpp TP TP TP C 7 C7 P.0 WP Vss 6 SCL CVcc ATC8 Optional VCC R R SW CRST CCLK C CIO + CVss C6 C8 Card Reader 0 JP JP7 B TP6 DVcc B CPRES CRST CCLK Vcc JP8 SIM Connector CIO Vss SW7 Vss JP9 TP7 TP8 TP9 A A Title T8XC Demonstration Board Size Do c ument Number R e v A..0 Date: Wednesday, December 8, 00 Sheet of 6- T8xC Starter Kit User Guide

27 Appendix A Figure 6-. Demonstration Board ( of ) D D VCC R6 JP RST VCC + C7 RST SW Reset R7 + C8 C C U7A U7B INT_SW6 SW INT 7HC 7HC DVCC B B JP D LED0 R LED 0 dummy resistor 0 ohm LED JP R9 D LED dummy resistor 0 ohm A A Title T8XC Demonstration Board Size Do c ument Number R e v A C Date: Wednesday, December 8, 00 Sheet of T8xC Starter Kit User Guide 6-

28 Appendix A Figure 6-. Demonstration Board ( of ) JH -V DC IN D0 SW D6 C0 + Vcc J C D8 D POWER ON D 9V DC IN ON/OFF + C TP JP Vcc R8 VIN VOUT ADJ R VCC + C U LM7_T C C C R C JR D Battery connector 9V DC IN U_B U_C CVss Vcc CVss Vcc B LI EVcc LI EVcc B CVcc DVcc CVcc DVcc Vss Vss P./CRST P./CRST 0 0 P./CCLK P.0/Rx P./CCLK P.0/Rx 6 P./CC P./Tx P./CPRES P./INT/OE 8 P./CC P./Tx 9 7 P./CPRES P./INT/OE P./CC8 P./T0 P./CC8 P./T P.0/CIO P./INT0 P.0/CIO P./INT0 0 RST XTAL XTAL P./CIO/T P.6/CCLK/LED0 P.7/CRST/LED 0 RST XTAL XTAL P./CIO/T P.6/CCLK/LED0 P.7/CRST/LED SSOP DIL A A Title T8XC Demonstration Board Size Do c ument Number R e v A C Date: Wednesday, December 8, 00 Sheet of 6- T8xC Starter Kit User Guide

29 Appendix A Figure 6-6. Demonstration Board ( of ) P0 ( 7:0 ) JR 8 6 D 8 6 D J_A J_B J_C 0 0 P0 ( 7:0 ) P P ( 7:0 ) C P. 0 P./CC 0 7 C P. P ( 7:0 ) P./CC8 6 6 P EA Vcc 7 ALE RST 8 8 P 9 PSEN 9 P ( 7:0 ) P Vcc 0 P.7 0 Vss Vss P ( 7:0 ) JR P.0 P. 8 6 P INT B P B T WR RD 0 0 DIN 6 female connector DIN 6 female connector DIN 6 female connector JR P P A A Title T8XC Demonstration Board Size Do c ument Number R e v A C Date: Wednesday, December 8, 00 Sheet of T8xC Starter Kit User Guide 6-

30 Appendix A 6. References n T8XC Product Datasheet. 6. Acronyms n ISP: In-System programming n FLIP: FLexible In-system Programming 6-6 T8xC Starter Kit User Guide

31 Atmel Headquarters Corporate Headquarters Orchard Parkway San Jose, CA 9 TEL (08) -0 FAX (08) Europe Atmel Sarl Route des Arsenaux Case Postale 80 CH-70 Fribourg Switzerland TEL () 6-6- FAX () Asia Room 9 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (8) FAX (8) 7-69 Japan 9F, Tonetsu Shinkawa Bldg. --8 Shinkawa Chuo-ku, Tokyo 0-00 Japan TEL (8) -- FAX (8) --78 Atmel Operations Memory Orchard Parkway San Jose, CA 9 TEL (08) -0 FAX (08) 6- Microcontrollers Orchard Parkway San Jose, CA 9 TEL (08) -0 FAX (08) 6- La Chantrerie BP Nantes Cedex, France TEL () FAX () ASIC/ASSP/Smart Cards Zone Industrielle 06 Rousset Cedex, France TEL () FAX () East Cheyenne Mtn. Blvd. Colorado Springs, CO TEL (79) FAX (79) 0-79 Scottish Enterprise Technology Park Maxwell Building East Kilbride G7 0QR, Scotland TEL () FAX () --7 RF/Automotive Theresienstrasse Postfach 70 Heilbronn, Germany TEL (9) FAX (9) East Cheyenne Mtn. Blvd. Colorado Springs, CO TEL (79) FAX (79) 0-79 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 8 Saint-Egreve Cedex, France TEL () FAX () literature@atmel.com Web Site Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company s standard warranty which is detailed in Atmel s Terms and Conditions located on the Company s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel s products are not authorized for use as critical components in life support devices or systems. Atmel Corporation 00. All rights reserved. ATMEL is a registered trademark of Atmel. Windows 98, Windows NT, and Windows 000 are registered trademarks of Microsoft Corporation. Other terms and product names may be the trademarks of others. Printed on recycled paper. /xm