delivering advanced Dry Ice solutions

Transcription

1 1

2 This catalog contains all of Cold Jet LLC s product offerings. All part numbers are included in this catalog. Cold Jet will always ship the latest version of each part. Invoices will always reflect the latest revision level numbers. Contact us: Customer Support* Cincinnati, OH Rancho Cucamonga, CA +32 (0) Europe East Coast (M-F 8:30-5:00 p.m.) West Coast (M-F 8:30-5:00 p.m.) info@coldjet.com * Customer Support is available 24 hours a day, 7 days a week. 3

3 Table of Contents PRODUCTS Blasting Equipment & Accessories Blasting Systems... 7 Applicators Cold Jet... 9 Alpheus...10 Nozzles/Barrels Cold Jet Low-Flow...11 Cold Jet Medium-Flow...14 Cold Jet Specialty High-Flow...18 Alpheus D-Series...20 Alpheus N-Series...22 Alpheus A-Series...24 Alpheus S-Series...25 Alpheus T-2 Series...27 Nozzle Accessories Cold Jet...28 Alpheus...32 Hoses & Hose Fittings Cold Jet...33 Alpheus...35 Accessories Cold Jet...37 Alpheus...38 Pelletizers P325, P750, P1500 & P Accessories...40 Block Maker...41 Engineered Systems Integrated Systems & Automated Cleaning Booth...42 FlashJet System...43 Safety Accessories...44 SERVICES Customer Support...45 Services...46 Cold Jet Solutions...47 Warranty Information...48 Terms & Conditions

4 Blasting Systems All blasting systems include one blast unit, one length each of air and blast hose, a cus tom er specifi ed applicator (unless otherwise noted) and nozzle (from appropriate group), and appropriate handle for nozzle (if ap pli ca ble). Alpheus PT-110 All pneumatic, dual-hose blast system Weight: 118 lbs (53.5 kg) Hopper lbs (50 kg) capacity Size (LxWxH): 18"x 14"x 42" Low-pressure system - 25 to 125 psi (1.72 to 8.62 bar) (86.4cm x 50.8cm x 96.5cm) Variable feed rate - 1 to 4 lbs/min (0.5 to 1.8 kg/min) Media - Pellets (3mm) Choice of A or D-series Applicator & Nozzle Cold Jet AeRO 30 Electric, single-hose blast system Weight: 165 lbs (75 kg) Fully isolated hopper - 30 lbs (13.6 kg) capacity Size (LxWxH): 25"x 17"x 30" Low-pressure system - 30 to 140 psi (2.1 to 9.7 bar) Alpheus Power PTX (63.5cm x 43.2cm x 76.2cm) Fixed feed rate lbs/min (0.7 kg/min) Media - Pellets (3mm) Standard applicator: Single-Speed Applicator Choice of nozzle from Group A Hose & Nozzle management devices Options Externally mounted blast pressure regulator Externally mounted coalescing air fi lter 3 lbs/min (1.36 kg/min) rotor Alpheus T-2 Electric, single-hose blast system Hopper capacity - 12 lbs ( 5.4 kg) capacity Weight: 103 lbs (46.7 kg) Low-pressure system - 30 to 120 psi (2.1 to 8.3 bar) Size (LxWxH): 22"x 14"x 20" Variable feed rate to 1.5 lbs/min (0.2 to 0.7 kg/min) (56cm x 36cm x 51cm) Ice Wand Applicator Media - Block (5"x 5"x 10") Choice of 12, 25 or 50 cfm (0.34, 0.71, or 1.42 m 3 /min) (12.7cm x 12.7cm x 25.4cm) Pencil Point Nozzle in 6" or 9" (15 or 22 cm) length (Standard 9" / 25 cfm (22 cm / 1.42 m 3 /min will be provided unless otherwise specifi ed) Options Durable transport cart with air fi lter (shown) All pneumatic, single-hose blast system Weight: 140 lbs (63.5 kg) Hopper lb. (50 kg) capacity Size (LxWxH): 18.5"x 14"x 45.8" Low-pressure system - 50 to 120 psi (3.4 to 8.27 bar) (43cm x 36cm x 116cm) Variable feed rate - 1 to 6 lbs/min (0.5 to 2.7 kg/min) Media - Pellets (3mm) Integral fi lter for blast air Choice of S-Series Applicator & Nozzle 7

5 Blast Systems All blasting systems include one blast unit, one length each of air and blast hose, a cus tom er specifi ed applicator (unless otherwise noted) and nozzle (from appropriate group), and appropriate handle for nozzle (if ap pli ca ble). Cold Jet AeRO 75 Electric, single-hose blast system Weight: 295 lbs (134 kg) Fully isolated hopper - 75 lbs (34 kg) capacity Size (LxWxH): 34"x 20"x 40" Low pressure system - 30 to 140 psi (2.1 to 9.7 bar) Cold Jet AeRO 75-DX Electric, single-hose blast system Weight: 315 lbs (143.2 kg) Fully isolated hopper - 75 lbs (34 kg) capacity Size (LxWxH): 34"x 20"x 40" Latch-turn slideout hopper (86.4cm x 50.8cm x 96.5cm) Full-pressure system - 30 to 300 psi (2.1 to 20.7 bar) Media - Pellets (3mm) Variable feed rate - 0 to 7 lbs/min (0 to 3.2 kg/min) Hose management system Hour meter Standard applicator: Tri-Mode Speed Applicator Choice of nozzle from Group A, B, or C Options Internally mounted air pressure regulator Externally mounted coalescing air fi lter (86.4cm x 50.8cm x 101.6cm) Variable feed rate - 0 to 7 lbs/min (0 to 3.2 kg/min) Media - Pellets (3mm) Hose & Nozzle management devices Hour meter Standard applicator: Single-Speed Applicator Choice of nozzle from Group A or B Options Internally mounted blast pressure regulator Externally mounted coalescing air fi lter Alpheus SDI-5 All pnematic, dual-hose blast system Weight: 315 lbs (142.9 kg) Hopper lbs (54.4 kg) capacity Size (LxWxH): 37"x 24.5"x 45" High-pressure system - 25 to 250 psi (1.72 to 17.2 bar) (94cm x 62.2cm x 114.3cm) Variable feed rate - 1 to 6 lbs/min (0.5 to 2.7 kg/min) Media - Pellets, Nuggets, and Hose management system Block (10"x 10"x 24") Integral fi lter for blast air (25.4cmx 25.4cmx 61cm) Choice of A, D, or N-series Applicator & Nozzle 8

6 Applicators Cold Jet Single-Speed - Part #: 2E0362-G1 Lightweight Single-fi nger trigger allows easy control of blasting power Safety switch Designed for right and left handed users Includes a JIC fi tting mounted to a rotary union for superior ergonomics Integrated Quick Change feature so that nozzles can be changed safely and easily Standard Applicator for AeRO 30 and AeRO 75 Tri-Mode Speed - Part #: 2E0362-G2 Lightweight Single-fi nger trigger allows easy control of blasting power Three position feed switch (Up - 75% feed, Center - machine controlled, Down - purge/air only) Safety switch Designed for right and left handed users Includes a JIC fi tting mounted to a rotary union for superior ergonomics Integrated Quick Change feature so that nozzles can be changed safely and easily Standard Applicator for AeRO 75-DX 90-Degree In-Line - Part #: 2E0350 Lightweight Ergonomic trigger Safety switch Works with all Micro Series (MS) nozzles and requires adaptor to work with all other nozzles Ideal for blasting into confi ned spaces Simple & easy design for better control of blasting power Foot Switch - Part #: 2G1070 Eliminates the need for a hand-held control switch Allows the nozzle to be attached directly to the blast hose for better ergonomics "Deadman style" safety foot pedal Hand Switch - Part #: 2E0258 Eliminates the need for a hand-held applicator Can be attached to the blast hose, an extension tube or can be hand held "Deadman style" safety switch Remote Switch - Part #: 2G1137 Remote start/stop station for fi xed applications Connects directly to blast control cable 9

7 Applicators Alpheus D-Series - Part #: M25 Lightweight Ergonomic design allows users to blast comfortably for long periods of time at blast pressures up to 125 psi (8.62 bar) Applicator can be used with dry ice pellets as well as the sugar-size granules produced from shaved block ice Sold only as part of hose assembly (Part #: M25) S-Series - Part #: For use with the Alpheus single-hose Power PTX Multi-fi nger trigger allows easy control of blasting power Nozzles can be changed easily and safely Applicator can use dry ice pellets as well as the sugar-size granules produced from shaved block ice A-Series - Part #: E25 Lightweight Multi-fi nger trigger allows easy control of blasting power Tefl on head glides easily over sensitive surfaces to prevent damage Designed to clean hard-to-reach areas with clearance as small as 8" (20.3 cm) Reverse-thrust capability directs an air stream through the back of the gun, providing superior balance and improved manoeuverability, even in one-hand operation Applicator can be used with dry ice pellets as well as the sugar-size granules produced from shaved block ice N-Series - Part #: Recommended for use on applications requiring pressures of 125 to 300 psi (8 to bar) Nozzles can be changed easily and safely Applicator can be used with dry ice pellets as well as the sugar-size granules produced from shaved block ice 10 Ice Wand - Part #: M25 For use with T-2 Lightweight Multi-fi nger trigger allows easy control of blasting power Safety switch Designed for right and left handed users Integrated Quick Change feature so that nozzles can be changed easily and safely Sold only as part of hose assembly (Part #: )

8 Low-Flow Nozzles Cold Jet Group A MS Part #: 2E Full pressure 45 o angle x 7.7" (19.6 cm) axial length. Minimum cavity opening of 3.5" (8.9 cm) At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 0.75" (1.9 cm) perpendicular to nozzle tube line Stainless steel nozzle with aluminum coupler and plastic coated Suggested for use with 3/4" (1.9 cm) OD Tube Style Handle - Part #: 2E0275 May be used with or without an extension for mold cleaning and other applications requiring this angle and swath orientation. MS Part #: 2E Full pressure 45 o angle x 7.8" (19.8 cm) axial length. Minimum cavity opening of 3.5" (8.9 cm) At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 0.75" (1.9 cm) in line with nozzle tube Stainless steel nozzle with aluminum coupler and plastic coated Suggested for use with 3/4" (1.9 cm) OD Tube Style Handle - Part #: 2E0275 May be used with or without an extension for mold cleaning and other applications requiring this angle and swath orientation. MS Part #: 2E Full pressure 90 o angle x 7" (17.8 cm) axial length. Minimum cavity opening of 5.3" (13.5 cm) At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 0.75" (1.9 cm) perpendicular to nozzle tube line Stainless steel nozzle with aluminum coupler and plastic coated Suggested for use with 3/4" (1.9 cm) OD Tube Style Handle - Part #: 2E0275 May be used with or without an extension for mold cleaning and other applications requiring this angle and swath orientation. MS Part #: 2E Full pressure 135 o angle x 7.3" (18.6 cm) axial length. Minimum cavity opening of 6.3" (16 cm) At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 0.75" (1.9 cm) in line with nozzle tube Stainless steel nozzle with aluminum coupler and plastic coated Suggested for use with 3/4" (1.9 cm) OD Tube Style Handle - Part #: 2E0275 May be used with or without an extension for mold cleaning and other applications requiring this angle and swath orientation. 11

9 Low-Flow Nozzles Cold Jet Group A MS Part #: 2E Full pressure 90 o angle x 7.3" (18.6 cm) axial length. Minimum cavity opening of 7" (17.8 cm) At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 1" (2.5 cm) in line with nozzle tube Stainless steel nozzle with aluminum coupler and plastic coated Suggested for use with 3/4" (1.9 cm) OD Tube Style Handle - Part #: 2E0275 May be used with or without an extension for mold cleaning and other applications requiring this angle and swath orientation. MS Part #: 2E Full pressure 90 o angle x 16.6" (42.2 cm) axial length. Minimum cavity opening of 3.4" (8.6 cm) At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 1" (2.5 cm) perpendicular to nozzle tube line Stainless steel nozzle with aluminum coupler and plastic coated Suggested for use with 3/4" (1.9 cm) OD Tube Style Handle - Part #: 2E0275 This nozzle works effectively in the smallest openings. The 16" length is usually suffi cient for most cleaning jobs but may be extended. Applications: Cleaning molds, especially PET molds. MS Part #: 2E0349 Full pressure 45 o angle x 7.3" (18.5 cm) axial length. Minimum cavity opening of 5" (12.7 cm) At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 1" (2.5 cm) perpendicular to nozzle tube line Stainless steel nozzle with aluminum coupler and plastic coated Suggested for use with 3/4" (1.9 cm) OD Tube Style Handle - Part #: 2E0275 This angled nozzle is one of a series that provides a customized angle and swath width to optimize the blasting of critical surfaces, a short length for excellent articulation that can be readily ex tend ed if desired. 12 TN Part #: 2E0314 Low Pressure At 80 psi (5.5 bar) requires 75 SCFM (2.1 m 3 /min) Blast swath is 0.5" (1.3 cm) Straight, 14" (35.6 cm) long Will not harm delicate tubing Ideal for cleaning deep-cavity injection molds. The longer length allows more fl ex i bil i ty for plants with different size slug molds and the small diameter allows the blast stream to escape the cavity being cleaned.

10 Low-Flow Nozzles Cold Jet Group A 510 SLF - Part #: 2E0341 Low pressure Straight, 10" (25.4 cm) long At 80 psi (5.5 bar) requires 50 SCFM (1.4 m 3 /min) Blast swath is 0.6" (1.5 cm) Aluminum Suggested for use with 1" (2.5 cm) OD Tube Style Handle - Part #: 2E0209 This nozzle provides a great combination of powerful cleaning and articulation with an exceptionally low air consumption - 50 SCFM (1.4 m 3 /min) thereby maximizing your cleaning without jeopardizing other compressed air operations. 523 SLF - Part #: 5E0179 Full pressure Straight, 23" (58.4 cm) long At 80 psi (5.5 bar) requires 50 SCFM (1.4 m 3 /min) Blast swath is 0.7" (1.8 cm) Aluminum Suggested for use with 1" (2.5 cm) OD Tube Style Handle - Part #: 2E0209 This nozzle provides powerful cleaning with an exceptionally low air consumption - 50 SCFM (1.4 m 3 /min) thereby maximizing your cleaning without jeopardizing other compressed air operations. TN Part #: 5E0183 Full pressure Straight, 10" (25.4 cm) long At 80 psi (5.5 bar) requires 50 SCFM (1.4 m 3 /min) Blast swath is 0.25" (0.6 cm) High-strength, low-temperature aluminum with a hard-coated aluminum base Alpha adapter required for this nozzle (P/N #: 3E0729) Suggested for use with 1 3/16" (3 cm) OD Tube Style Handle - Part #: 2E0289 The 1" (2.5 cm) FJIC end fi tting on this nozzle allows for its use as a direct-to-hose nozzle or for it to be attached to extensions or a 90-degree in-line applicator. This nozzle is ideal for cleaning deep-cavity injection molds. "J" Hook - Part #: 2E o angle blast fl ow turn At 80 psi (5.5 bar) requires 70 scfm (1.96 m 3 /min) Blast swath is 0.25" (0.6 cm) Plastic coated stainless steel nozzle See through safety blast shield Suggested for use with 3/4" (1.9 cm) OD Tube Style Handle - Part #: 2E0275 This nozzle is designed for PET mold cleaning and similar applications. 13

11 Medium-Flow Nozzles Cold Jet Group B 205 BL - Part #: 2E0321 Low pressure 80 o angle x 8.3" (21 cm) axial length At 80 psi (5.5 bar) requires 155 SCFM (4.4 m 3 /min) Blast swath is 0.83" (2.1 cm) Minimum cavity opening of 12.3" (31.2 cm) Aluminum with stainless steel tubing Shown with 1" (2.5 cm) OD Tube Style Handle - Part #: 2E0209 Moderate aggression low pressure nozzle designed to turn the fl ow 80 degrees for horizontal surfaces. Applications: Wafer plate cleaning, rubber mold cleaning, degreasing and general maintenance. 218 SL - Part #: 50E103 Low Pressure Straight, 18" (545.7 cm) long At 80 psi (5.5 bar) requires 165 SCFM (4.7m 3 /min) Blast swath is 3" (7.6 cm) Aluminum Recommended for use with Clamp Style Handle - Part #: 2E0287 The wide swath of this nozzle makes it ideal for a mild cleaning of large surface areas and provides a consistent level of cleanliness without "streaks" over the entire surface. Applications: Removing wax mold release from foam molds, and ideal for routine general maintenance cleaning. 223 SL - Part #: 5E0190 Low Pressure Straight, 23" (58.4 cm) long At 80 psi (5.5 bar) requires 165 SCFM (4.7m 3 /min) Blast swath is 3" (7.6 cm) Aluminum Recommended for use with Clamp Style Handle - Part #: 2E0287 This high performance nozzle is designed to gives an aggressive, continuous non-pulsing and smooth 3" (7.6 cm) blast path. 14

12 Medium-Flow Nozzles Cold Jet Group B 307 BL - Part #: 2E0322 Low pressure 45 o angle x 8.9" (22.6 cm) axial length At 80 psi (5.5 bar) requires 120 SCFM (3.4 m 3 /min) Blast swath is 0.75" (1.9 cm) Minimum cavity opening of 4" (10.16 cm) Aluminum Shown with Threaded Style Handle - Part #: 2E0245 Low pressure nozzle designed to turn the fl ow 45 degrees for mild cleaning in tight spaces. The nozzle's small exit tip makes it ideal for tight-access cavities. Applications: Cleaning rubber molds and general removal of mold release agents. 402 SL - Part #: 5E0160 Low pressure Straight, 2" (5.1 cm) long At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 1" (2.5 cm) Aluminum This nozzle's small size makes it ideal for tight-access cavities. Applications: Cleaning rubber molds and general removal of mold release agents. 403 SL - Part #: 2E0331 Low pressure Straight, 3" (7.6 cm) long At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 0.5" (1.3 cm) Aluminum This nozzle's small size makes it ideal for tight-access cavities. Applications: Cleaning rubber molds and general removal of mold release agents. 15

13 Medium-Flow Nozzles Cold Jet Group B 412 SL - Part #: 5E0156 Low pressure Straight, 12" (30.5 cm) long At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 1" (2.5 cm) Aluminum Suggested for use with 1 3/16" (3 cm) OD Tube Style Handle - Part #: 2E0289 This nozzle delivers maximum performance for low-fl ow and low-pressure air sys tems. It is ideal for removing release agents from permanent aluminum molds and any application requiring an aggressive blast. Applications: Cleaning rubber molds and general removal of mold release agents. 413 SL - Part #: 5E0159 Low pressure Straight, 12" (30.1 cm) long At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 1.8" (4.6 cm) Aluminum Suggested for use with 1 3/16" (3 cm) OD Tube Style Handle - Part #: 2E0289 The wide swath on this nozzle makes it ideal for removing wax release agents from polyurethane foam molds. Applications: Cleaning rubber molds, general removal of mold release agents, as well as general maintenance. 508 SL - Part #: 2E0323 Low pressure Straight, 8" (20.3 cm) long At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 0.75" (1.9 cm) Aluminum Suggested for use with 1" (2.5 cm) OD Tube Style Handle - Part #: 2E0209 This nozzle is an excellent combination of power and manoeuverability. Applications: Cleaning rubber and urethane molds, and general removal of mold release agents. 16

14 Medium-Flow Nozzles Cold Jet Group B 523 SF - Part #: 5E0175 Full pressure Straight, 23" (58.4 cm) long At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 1" (2.5 cm) Aluminum Suggested for use with 1" (2.5 cm) OD Tube Style Handle - Part #: 2E0209 This nozzle has the best track record for effectiveness and aggression at most pressure levels. Applications: Cleaning tire molds (side wall, treads, and micro-vents), urethane molds, general removal of mold re leas e agents, and high-aggression general maintenance. 523 SF.2 - Part #: 5E0176 Full pressure Straight, 23" (58.4 cm) long At 80 psi (5.5 bar) requires 100 SCFM (2.8 m 3 /min) Blast swath is 2" (5.1 cm) Aluminum Suggested for use with 1 3/16" (3 cm) OD Tube Style Handle - Part #: 2E0289 Applications: Cleaning tire molds (side wall, treads, and micro-vents), urethane molds, general removal of mold re leas e agents, and general maintenance. 807 SL - Part #: 5E0141 Low pressure Straight, 7" (17.8 cm) long At 80 psi (5.5 bar) requires 150 SCFM (4.3 m 3 /min) Blast swath is 2" (5.1 cm) Aluminum The wide cleaning swath makes this nozzle ideal for general degreasing and industrial clean-ups. Applications: Cleaning rubber molds and general removal of mold release agents. TN Part #: 2E0302-Length Full pressure Length: Customer Specifi ed - up to 10" (25.4 cm) At 80 psi (5.5 bar) requires 150 SCFM (4.3 m 3 /min) Blast swath is 0.5" (1.3 cm) Will not harm delicate tubing Ideal for cleaning deep-cavity injection molds. 17

15 Specialty High-Flow Nozzles Cold Jet Group C 523 Stealth - Part #: 5E0167 Full pressure Straight, 23" (58.4 cm) long At 80 psi (5.5 bar) requires 150 SCFM (4.3 m 3 /min) Blast swath is 1" (2.5 cm) Lightweight composite Suggested for use with 1 3/16" (3 cm) OD Tube Style Handle - Part #: 2E0289 Polymer construction will not damage surfaces in case of accidental contact with nozzle. Applications: Cleaning tire molds (side wall, treads, and micro-vents), urethane molds, aluminum core boxes, and general removal of mold re leas e agents. 533 SF - Part #: 5E0161 Full pressure Straight, 33" (83.8 cm) long At 80 psi (5.5 bar) requires 150 SCFM (4.3 m 3 /min) Blast swath is 1" (2.5 cm) Aluminum Suggested for use with 1" (2.5 cm) OD Tube Style Handle - Part #: 2E0209 Ideal nozzle for contract cleaning jobs due to its high aggression. Applications: Cleaning tire molds, urethane molds, general removal of mold release agents, and any general maintenance. 533 SF.2 - Part #: 5E0164 Full pressure Straight, 33" (83.8 cm) long At 80 psi (5.5 bar) requires 150 SCFM (4.3 m 3 /min) Blast swath is 2" (5.1 cm) Aluminum Suggested foruse with 1 3/16" (3 cm) OD Tube Style Handle - Part #: 2E0289 High-performance nozzle ideal for contract cleaning jobs due to its high aggression. Applications: Cleaning tire molds, urethane molds, and general removal of mold release agents. 18

16 Specialty High-Flow Nozzles Cold Jet Group C 902 BL - Part #: 2E0249 Low pressure 90 o angle with "air jet" opposite "blast jet" to balance nozzle thrust. Minimum cavity opening of 5" (12.7 cm) At 80 psi (5.5 bar) requires 215 SCFM (6.1 m 3 /min) Blast swath is 0.5" (1.3 cm) Aluminum with Tefl on bumper pads Battery operated lights Nozzle includes 10" (25.4 cm) extension tube (not shown) Suggested for use with 1" (2.5 cm) OD Tube Style Handle - Part #: 2E0209 Unique 90 degree nozzle utilizes an air jet, opposite in direction to the blast stream, to balance the nozzle. Applications: Removing general mold release agents, oils and greases, and some rubber compounds. TN Part #: 5E " OD (1.78 cm) -Bullet Nozzle At 80 psi (5.5 bar) requires 175 SCFM (5 m 3 /min) Length: 9" (22.9 cm) 3-"Jet" blast openings for full circumferential blast jet Alpha adapter required for this nozzle (P/N #: 3E0729) Ideal for cleaning the walls of deep-cavity injection molds, and recessed areas. 19

17 D-Series Nozzles Alpheus 2" (5.08 cm) 3" (7.62 cm) 4" (10.16 cm) 5" (12.7 cm) 6" (15.24 cm) 7" (17.78 cm) 8" (20.32 cm) Series 51 Series 53 Series 56 Series Blue color represents Black ABS. Other listing is Aluminum. All have 1 1/4" (3.18 cm) OD. Choosing a Stinger for your nozzle (using combination chart below): Determine your desired blast pressure (i.e.: if you wish to blast at 90 psi (6.21 bar), choose an LF85, MF85, or HF85 stinger, each with an operating range of psi ( bar). Based on the air flow rate your compressor can provide, choose a Low-Flow, Medium-Flow, or High-Flow stinger. (For maximum cleaning aggression, choose the highest air flow available from your compressor). Once you have selected a stinger, examine the chart below to determine which nozzle series (above) is appropriate for that stinger. EXAMPLE: If you wish to blast at 90 psi (6.21 bar) and your compressor can supply 160 SCFM (4.5 m 3 /min), you would choose an MF85 stinger and a matching nozzle from Series 53. STINGER-PSI Desired Operating Range Minimum Required Flow Rate Stinger Low Flow LF psi ( bar) 70 SCFM (2.0 m 3 /min) t LF psi ( bar) 110 SCFM (3.1 m 3 /min) t LF psi ( bar) 160 SCFM (4.5 m 3 /min) t Med. Flow MF psi ( bar) 120 SCFM (3.4 m 3 /min) t MF psi ( bar) 150 SCFM (4.2 m 3 /min) t MF psi ( bar) 225 SCFM (6.4 m 3 /min) t High Flow HF psi ( bar) 125 SCFM (3.5 m 3 /min) t HF psi ( bar) 195 SCFM (5.5 m 3 /min) t HF psi ( bar) 240 SCFM (6.8 m 3 /min) t 20

18 D-Series Nozzles Alpheus Fan Nozzle - Part #: (Aluminum) (Stainless Steel) Length: 15.5" (39.4 cm) Blast swath 2.375" x 0.25" (6.033 cm x cm) Medium Air Flow of 85 Ideal for easier to clean applications, less aggressive than barrel nozzles. Extended Length Nozzles - Aluminum Wrapped ABS - Part #: Customized to any length from 18" to 36" (45.72 cm to cm) Ideal for longer distance hard to reach areas. Bendable Nozzle - Part #: (5/8"/1.59 cm Dia.) (1/2"/1.27 cm Dia.) Length: 8" (20.32 cm) Allows you to gently shape the barrel to get around obstructions that block your cleaning path Due to its diameter, this nozzle is low-fl ow and may be less aggressive than larger diameter nozzles NOTE: Special stinger part number may be required Ideal for hard to reach areas. 21

19 N-Series Nozzles Alpheus N-Series Standard Round Nozzles Part Number Size (L x OD) ID " L x 1.25" OD 0.63" (1.6 cm) " L x 1.25" OD 0.633" (1.608 cm) " L x 1.25" OD 0.5" (1.27 cm) " L x 1.25" OD 0.562" (1.427 cm) " L x 1.25" OD 0.625" (1.587 cm) " L x 1.25" OD 0.687" (1.745 cm) " L x 1.25" OD 0.75" (1.905 cm) " L x 1.25" OD 0.594" (1.509 cm) " L x 1.25" OD 0.656" (1.666 cm) " L x 1.25" OD 0.531" (1.349 cm) Blue color represents Black ABS. Other listing is Aluminum. Choosing a Stinger for your nozzle (using the combination chart below): Determine your desired blast pressure (i.e.: if you wish to blast at 90 psi (6.21 bar), choose an LF85, MF85, or HF85 stinger, each with an operating range of psi ( bar). Based on the air flow rate your compressor can provide, choose a Low-Flow, Medium-Flow, or High-Flow stinger. (For maximum cleaning aggression, choose the highest air flow available from your compressor). Once you have selected a stinger, examine the chart below to determine which nozzle is appropriate for that stinger. EXAMPLE: If you wish to blast at 90 psi (6.21 bar) and your compressor can supply 160 SCFM (4.5 m 3 /min), you would choose an MF85 stinger and matching nozzle. Stingers for Standard Round Nozzles # X 22 STINGER-PSI Operating Range Required Flow Rate Stinger Nozzle Low Flow LF psi ( bar) 70 SCFM (2.0 m 3 /min) LF psi ( bar) 110 SCFM (3.1 m 3 /min) LF psi ( bar) 160 SCFM (4.5 m 3 /min) LF psi ( bar) 215 SCFM (6.1 m 3 /min) LF psi ( bar) 255 SCFM (7.2 m 3 /min) Med. Flow MF psi ( bar) 120 SCFM (3.4 m 3 /min) MF psi ( bar) 150 SCFM (4.2 m 3 /min) MF psi ( bar) 225 SCFM (6.4 m 3 /min) MF psi ( bar) 305 SCFM (8.6 m 3 /min) High Flow HF psi ( bar) 125 SCFM (3.5 m 3 /min) HF psi ( bar) 195 SCFM (5.5 m 3 /min) HF psi ( bar) 240 SCFM (6.8 m 3 /min) HF psi ( bar) 340 SCFM (9.6 m 3 /min)

20 N-Series Nozzles Alpheus Aluminum Fan Nozzle - Part #: Size: 14" L x 2.5" W (35.56 cm x 6.35 cm) Blast swath: 2" (5.08 cm) Works with higher pressure applications. 23

21 A-Series Nozzles Alpheus 2" (5.08 cm) 3" (7.62 cm) 4" (10.16 cm) 5" (12.7 cm) 6" (15.24 cm) 7" (17.78 cm) 8" (20.32 cm) Series 51 Series 53 Series 56 Series Blue color represents Black ABS. Other listing is Aluminum. All have 1 1/4" (3.175 cm) OD. Choosing a Stinger for your nozzle (using the combination chart below): Determine your desired blast pressure (i.e.: if you wish to blast at 90 psi (6.21 bar), choose an LF85, MF85, or HF85 stinger, each with an operating range of psi ( bar). Based on the air flow rate your compressor can provide, choose a Low-Flow, Medium-Flow, or High-Flow stinger. (For maximum cleaning aggression, choose the highest air flow available from your compressor). Once you have selected a stinger, examine the chart below to determine which nozzle series (above) is appropriate for that stinger. EXAMPLE: If you wish to blast at 90 psi (6.21 bar) and your compressor can supply 160 SCFM (4.5 m 3 /min), you would choose an MF85 stinger and a matching nozzle from Series STINGER-PSI Desired Operating Range Minimum Required Flow Rate Stinger Low Flow LF psi ( bar) 70 SCFM (2.0 m 3 /min) t LF psi ( bar) 110 SCFM (3.1 m 3 /min) t LF psi ( bar) 160 SCFM (4.5 m 3 /min) t Med. Flow MF psi ( bar) 120 SCFM (3.4 m 3 /min) t MF psi ( bar) 150 SCFM (4.2 m 3 /min) t MF psi ( bar) 225 SCFM (6.4 m 3 /min) t High Flow HF psi ( bar) 125 SCFM (3.5 m 3 /min) t HF psi ( bar) 195 SCFM (5.5 m 3 /min) t HF psi ( bar) 240 SCFM (6.8 m 3 /min) t

22 S-Series Nozzles Alpheus S-Series Standard Round Nozzle - Part #: Low Flow Size: 12.38" L x 1" OD x 0.32" ID (31.43 cm L x 2.54 cm OD x 0.80 cm ID) Part #: High Flow Size: 12.38" L x 1" OD x 0.53" ID (31.43 cm L x 2.54 cm OD x 1.33 cm ID) Ideal for most single-hose cleaning applications. S-Series Snub Nose Round Nozzle - Part #: Size: 6" L x 1" OD (15.24 cm L x 2.54 cm OD) Ideal for use in confi ned spaces. Shorter version of Standard Round Nozzle. S-Series Bent Tube Nozzle - Part #: High Flow Size: 13.1" L x 7/16" OD (33.27 cm L x 1.11 cm OD) 45 o angle Part #: Low Flow Size: 13.1" L x 3/8" OD (33.27 cm L x 0.95 cm OD) 45 o angle S-Series Straight Tube Nozzle - Part #: High Flow Size: 13.7" L x 7/16" OD (34.8 cm L x 1.11 cm OD) Part #: Low Flow Size: 13.7" L x 3/8" OD (34.8 cm L x 0.95 cm OD) Ideal for small openings and confi ned spaces. S-Series Rounded Fan Nozzle - Part #: Size: 12 3/4" L x 1 1/2" W x 0.4" H (32.38 cm L x 3.81 cm W x 1.02 cm H) Requires 1" (2.54 cm) ring (P/N# ) for recommended handle (P/N# A) and grip (P/N# ). Blast swath: 1" (2.54 cm) 25

23 S-Series Nozzles Alpheus S-Series Rounded Fan Nozzle - Part #: Size: 24" L x 2.230" W (60.96 cm L x cm W) Blast swath: 1.75" (4.445 cm) Requires 1 1/2" (3.81 cm) ring (P/N# ) for recommended handle (P/N# A) and grip (P/N# ) Part #: High Flow Size: 24" L x 1.230" W x 1" H (60.96 cm L x cm W x 2.54 cm H) Blast swath: 0.867" (2.202 cm) Requires 1" (2.54 cm) ring (P/N# ) for recommended handle (P/N# A) and grip (P/N# ) Part #: Low Flow Size: 24" L x 1.380" W x 1" H (60.96 cm L x cm W x 2.54 H) Blast swath: 0.867" (2.202 cm) Requires 1" (2.54 cm) ring (P/N# ) for recommended handle (P/N# A) and grip (P/N# ) Ideal for longer, harder to reach and overhead areas. S-Series 45 o Angle Extended Fan Nozzle - Part #: High Flow Size: 20" L x 2" W (50.8 cm L x 5.08 cm W) Blast swath: 2" (5.08 cm) Includes 1 1/4" (2.858 cm) grip ring assembly Part #: Low Flow Size: 20" L x 2.340" W (50.8 cm L x cm W) Blast swath: 2" (5.08 cm) Includes 1 1/4" (2.858 cm) grip ring assembly 26

24 T-2 Nozzles Alpheus T-2 Nozzles - Part #: Length 9" (22.86 cm) Length 6" (15.24 cm) Low Flow Yellow color 12 cfm (0.34 m 3 /min) Part #: Length 9" (22.86 cm) Length 6" (15.24 cm) Low Flow White color 25 cfm (0.71 m 3 /min) Part #: Length 9" (22.86 cm) Length 6" (15.24 cm) Low Flow Blue color 50 cfm (1.42 m 3 /min) 27

25 Nozzle Accessories Cold Jet Nozzle Case - Part #: 3E0773C Protect and store nozzles in this mobile rugged plastic case Holds up to 11 nozzles and accompanying accessories Wheels on one end for easy transport Nozzles shown are sold separately Adjustable Tube Handle Part #: 2E0275-3/4 (1.9 cm) OD 2E (2.6 cm) OD 2E /16 (3 cm) OD Slides easily and rotates around the extension tubes for optimal comfort and control Fully adjustable. Loosen and lock by rotating the handle. Allows for a horizontal or vertical orientation Threaded Nozzle Handle - Part #: 2E0245 Improves ergonomics Threads into 307 BL nozzle Adjustable Clamp-Style Nozzle Handle - Part #: 2E0287 This handle slides along grooves milled into the edges of the new rectilinear nozzles Designed to work with the 218 SL and 223 SL nozzles Alpha Series 1/2 (1.3 cm) to 1 (2.5 cm) Adapter Part #: 2E0295 Permits all nozzles to be used with the fl ange style 1" (2.54 cm) OD nozzle extension tube Allows the 1" (2.54 cm) OD nozzle extension tube to be used with Cold Jet Applicators Aluminum 28 Alpha Series 3/4 (1.9 cm) Base Coupler - Part #: 3E0729 Allows the Micro-Series (MS) type nozzles to be used with the Cold Jet Applicators or other nozzle base Aluminum

26 Nozzle Accessories Cold Jet Nozzle Base - Part #: 2E0233 Provides for the extension of any Radial Feed Series nozzle in a orientation beyond the exit of the blast applicator The patented 180 o base turns blast fl ow 180 o while main tain ing pellet integrity and blast aggression Ideal for cleaning confi ned spaces Quick Change Module - Part #: 2E0290 Enables quick and safe nozzle changes Can be used with all of Cold Jet's nozzles, with appropriate couplings and end fi ttings 3/4" (1.9 cm) JICF Quick Change Module Part #: 2E0360 Used on the 90-Degree In-Line Applicator Enables quick and safe nozzle changes Can be used with all of Cold Jet's nozzles, with appropriate couplings and end fi ttings JIC Modular End Fittings 1 (2.5 cm) JIC - Part #: 2N0060 3/4 (1.9 cm) JIC - Part #: 2N0064 Allows a nozzle base, extension tubes, or a rotary union to be connected directly to the blast hose Aluminum Precision Rotary Union - Part #: 2N0073 Allows full rotation when a nozzle is attached to a blast hose or extension tube Stainless Steel 3/4 (1.9 cm) JIC Rotary Union - Part #: 2N0163 Allows full rotation when a nozzle is attached to a blast hose, extension tube, or appropriate nozzle extension 3/4" (1.9 cm) JICF to 3/4" (1.9 cm) JICM Lightweight Hard-coat anodized Aluminum Adapter, Nozzle Retention x 3/4" (1.9 cm) JICF Part #: 3E0842 Allows all fl ange-style nozzles to be used with the 90-Degree In-Line Applicator 29

27 Nozzle Accessories Cold Jet Flange Style 1 (2.54 cm) OD Nozzle Extension Tube Part #: 2E Length 2E Length - with coupler Used for extending nozzle-base assemblies with minimum pressure loss Can be used with all available nozzles Available in 2" (5.1 cm), 10" (25.4 cm), 20" (50.8 cm) or 30" (76.2 cm) lengths Stainless Steel 3/4 (1.9 cm) OD Nozzle Extension Tube Part #: 3E Length Used for extending Micro-Series (MS) type nozzles directly from the applicator or nozzle-base Available in 5" (12.7 cm), 10" (25.4 cm), 15" (38.1 cm) or 20" (50.8 cm) lengths Stainless Steel Recommend purchasing a 3/4" (1.9 cm) JICM Fitting (12HTX-S) with this Extension Tube 1 (2.54 cm) OD Nozzle Bent Entry Tube Part #: 2E0227 Used for turning nozzle-base assemblies with minimum pressure loss Can be used with all nozzles Standard turning angle is 80 degrees, but other angles are available through special order Stainless Steel 1 (2.54 cm) OD Nozzle Bent Entry Tube with Extension Part #: 2E0259 Used for turning nozzle-base assemblies with minimum pressure loss Can be used with all nozzles Turning angle of 80 degrees with an 11" (28 cm) linear extension after the turn Stainless Steel 30

28 Nozzle Accessories Cold Jet 1" (2.54 cm) Nozzle Deflector Plate Part #: 2E0367 Used with the 523 SF and 412 SL nozzles to break-up pellets Nozzle sold separately 2" (5.08 cm) Nozzle Deflector Plate Part #: 2E0352 Used with the 807 SL nozzle to break-up pellets Nozzle sold separately Flow Divider Part #: 2E /4 (3.2 cm) Hose to Two 1 (2.5 cm) Hos es 2E /2 (3.8 cm) Hose to Two 1 1/4 (3.2 cm) Hos es 2G Dual Trigger Interconnect Box Splits one blast hose into two blast hoses for simultaneous blasting The unique fl ow path contour allows the pellets to separate into two paths while maintaining pellet integrity A dual-trigger interconnect box is required (P/N #: 2G1157) 31

29 Nozzle Accessories Alpheus Cold Jet MS Nozzle Adapter to Alpheus S-Series Applicator - Part #: 3N0050 Used to attach Cold Jet MS-Series nozzles to Alpheus S-Series Applicator Can be used with all Cold Jet MS-Series nozzles Aluminum Handle for Nozzle Handle Assembly Part #: Handle allows for easier maneuverability and improved ergonomics of nozzles while blasting Can be used with all Alpheus nozzles Entire Handle Assembly shown at left Grip for Nozzle Handle Assembly Part #: Rubber coating placed over handle for easier grip Ring for Nozzle Handle Assembly Part #: (1"/ 2.54 cm) (1 1/4" / 2.88 cm) (1 1/2" / 3.81 cm) (7/8" / cm) Slides easily and rotates around the nozzle for optimal comfort and control Attaches to Handle 32

30 Hoses & Hose Fittings Cold Jet Low-Pressure Urebrade Core Blast Hose Part #: 12-UNS /4" (1.9 cm) ID, 140 psi (8.3 bar), 20' (6.1 m) section Part #: 12-U5S with control cable Part #: 16-UNN " (2.5 cm) ID, 140 psi (8.3 bar), 20' (6.1 m) section Part #: 16-U5N with control cable Part #: 20-UNN /4" (3.2 cm) ID, 140 psi (8.3 bar), 20' (6.1 m) section Part #: 20-U5N with control cable Full-Pressure Kevlar Braided Blast Hose with Urebrade Core Part #: 16-KNN " (2.5 cm) ID, 300 psi (20.7 bar), 20' (6.1 m) section Part #: 16-K5N with control cable Part #: 20-KNN " (3.2 cm) ID, 300 psi (20.7 bar), 20' (6.1 m) section Part #: 20-K5N with control cable Full-Pressure Stainless Steel Blast Hose Part #: 16-SNN " (2.5 cm) ID, 300 psi (20.7 bar), 20' (6.1 m) section Part #: 16-S5N with control cable Compressed Air Hose - Part #: 2N0146-G1 25' (7.6 m) Section 1" (2.5 cm) ID 300 psi (20.7 bar) Used to carry pressurized air from air source to blast unit. Includes swivel adapters. For each length of hose ordered, order one Whip Check! (see page 44) Control Cable - Part #: 4G ' (6.1 m) Section. Use to connect switch or applicator to blast unit. 33

31 Hoses & Hose Fittings Cold Jet JIC Blast Hose Fittings Part #: 12HTX-S - 3/4" (1.9 cm) JICM Part #: 16HTX-S - 1" (2.5 cm) JICM Part #: 20HTX-S - 1 1/4" (3.2 cm) JICM Part #: 16-12HTX-S - 1" JICM (2.5 cm) to 3/4" (1.9 cm) JICM Part #: 16-12TRBTX-S - 1" (2.5 cm) JICF sleeve to 3/4" (1.9 cm) JICM nut Part #: 5N /4" (3.2 cm) JICF to 1" (2.5 cm) JICM aerodynamic Part #: 5N /4" (3.2 cm) JICM to 1" (2.5 cm) JICM aerodynamic Compressed Air Hose and Plant Air Pipe Fitting Part #: 4N Female Swivel Adapter Control Cable Accessories Male Plug - Part #: 4G0821 Female Receptacle - Part #: 4G0833* - Cable clamp 4G0834* - 5-pin socket *(both required) Replacements for damaged end fi ttings on control cable. 34 JICF to JICM Adapter 1" (2.5 cm) JICF to 1 1/4" (3.2 cm) JICM Adapter Part #: /4" (1.9 cm) JICF to 1" (2.5 cm) JICM Adapter Part #:

32 Hoses & Hose Fittings Alpheus D-Series Blast Hose Assembly Part #: E15 Hose & Gun Assembly, 15' (4.57 m) section, 125 psi (8.62 bar) for Alpheus PT-110 Part #: M20E Hose & Gun Assembly, 20' (6.1 m) section, 150 psi (10.34 bar) for Alpheus SDI-5 N-Series Blast Hose Assembly Part #: Hose Assembly only, 20' (6.1 m) section, 150 psi (10.34 bar) for Alpheus SDI-5 Part #: Stainless Steel Hose Assembly only, 25' (7.62 m) section, 300 psi (20.7 bar) for Alpheus SDI-5 A-Series Blast Hose Assembly Part #: E15 Hose & Gun Assembly, 15' (4.57 m) section, 125 psi (8.62 bar) for Alpheus PT-110 Hose Assembly only - Part #: E15A Part #: M20 Hose & Gun Assembly, 20' (6.1 m) section, 125 psi (8.62 bar) for Alpheus SDI-5 Hose Assembly only - Part #: M20A S-Series Blast Hose Assembly Part #: PTX20 Hose Assembly only, 20' (6.1 m) section, 125 psi (8.62 bar) for Alpheus Power PTX Ice Wand Blast Hose Assembly Part #: Hose & Gun Assembly, 15' (4.57 m) section 120 psi (8.27 bar) for Alpheus T-2 35

33 Hoses & Hose Fittings Alpheus Air Supply Hose - Part #: Low Pressure 25' (7.6 m) Section, 1" (2.5 cm) ID 150 psi (10.34 bar) Used to carry pressurized air from air source to blast unit (for all Alpheus blast systems except T-2) Guerilla Air Supply Hose - Part #: High Pressure 25' (7.6 m) Section, 1" (2.5 cm) ID 300 psi (20.7 bar) Used to carry pressurized air from air source to blast unit (for all Alpheus blast systems except T-2) T-2 Air Supply Hose - Part #: ' (7.6 m) Section, 1/2" ID (1.27 cm) Used to carry pressurized air from air source to blast unit (for Alpheus T-2 blast system) Hose assembly comes with fi ttings 36

34 Accessories Cold Jet Externally Mounted Coalescing Air Filter (CAF) Part #: 2M0020-G3 Designed to remove large amounts of water, oil, rust, and/or other particles from the air supply Optional pressure regulator available to precisely control incoming air pressure Externally Mounted Coalescing Air Filter (CAF) for AeRO 30 - Part #: 2M0018-G2 Designed to remove large amounts of water, oil, rust, and/or other particles from the air supply Low High Air Pressure Regulator Internal Low-Working Pressure (for AeRO 75 and 75-DX) - Part #: 2I0100-G2 External Low-Working Pressure - Part #: 2M0020-G1 External High-Working Pressure - Part #: 2M0020-G2 Externally mounted - can be mounted at the plant's air drop, on a machine mounted CAF, or on an air inlet to the Cold Jet Blast Units 1 1/2 lbs/min (0.68 kg/min) Rotor - Part #: 3E lbs/min (1.4 kg/min) Rotor - Part #: 3E0848 Used in the Cold Jet AeRO 30 only AeRO 30 Conversion Kit* to 3 lbs/min - Part #: 3E0848 Includes the following parts/accessories: 3 lb/min (1.4 kg/min) Rotor - Part #: 3E0833 1" (2.5 cm) Urebrade Blast Hose with control cable - Part #: 16-U5N /4" (1.9 cm) JICF to 1" (2.6 cm) JICM Adapter - Part #: With the Conversion Kit you may choose one nozzle from Cold Jet Group A or B. Note: This nozzle is not added to the nozzle that comes with the system initially; purchasing the conversion kit will allow you to choose from a wider selection of nozzles. * This conversion kit is sold as a kit only when purchased with an AeRO 30. If conversion is desired at a later date, each individual part (above) must be purchased seperately. 37

35 Accessories Alpheus Block Handler - Part #: Allows for easy transport of block ice from container to blasting machine T-2 Transport cart with Air Filter Allows for easy transport of T-2 blast system Includes Air Filter 38

36 Pelletizers P325 Automatic pellet production capability of up to 300 lbs (136.4 kg) of dry ice per hour Choice of 1 mm, 2 mm, 3 mm, or 6 mm diameter high-density pellets P750 Automatic pellet production capability of up to 600 lbs (272.7 kg) of dry ice per hour Choice of 1 mm, 2 mm, 3 mm, or 6 mm diameter high-density pellets, or 9 mm, 12 mm, 16 mm or 19 mm diameter high-density nuggets P1500 Automatic pellet production capability of up to 1200 lbs (545.5 kg) of dry ice per hour Choice of 1 mm, 2 mm, 3 mm, or 6 mm diameter high-density pellets, or 9 mm, 12mm, 16 mm or 19 mm diameter high-density nuggets P3000 Automatic pellet production capability of up to 2400 lbs ( kg) of dry ice per hour Choice of 1 mm, 2 mm, 3 mm, or 6 mm diameter high-density pellets, or 9 mm, 12 mm 16 mm or 19 mm diameter high-density nuggets Pelletizer Features Programmable Logic Controller (PLC) offers operating flexibility One button emergency stop function Built in fork lift tubes All welded steel, powder coated frame Fills blast unit or pellet boxes with dry ice System redundancy for enhanced reliability Options Stainless Steel hoods and washdown panel option (P750 and P1500 only) Die plates to produce a variety of pellet sizes Hardware kit to connect to a CO 2 vapor recovery system 39

37 Pelletizer Accessories High-Density Die Plates Available in the following diameters: 1 mm 9 mm 2 mm 12 mm 3 mm 16 mm 6 mm 19 mm Interchangeable die plates All dry ice produced is of the highest density achievable resulting in a lower sublimination rate Stainless Steel Hoods and Panel Kit Part #: 2J for P750 Part #: 2J for P1500 Wash-down capable skin panels and hoods located over extruders Vapor Recovery Kit Part #: 2K for P750 Part #: 2K for P1500 Part #: 2K for P3000 (2 required) Recommended back-pressure is no more than 10 psi (0.7 bar). Higher back-pressure will infl uence the fl ow of liquid CO 2 into the snow chamber and can decrease production rate and dry ice quality Storage Containers Part #: 4E Cubic Foot (0.3 m 3 ) Part #: 4E Cubic Foot (0.3 m 3 ) with cast ers and hinged lid Part #: 4E Cubic Foot (0.5 m 3 ) Insulated for optimum preservation Removable lids for easy fi lling Fork lift accessible 40

38 Block Maker BlockMaster The Alpheus Series BlockMaster uses liquid carbon dioxide to create consistent, high-quality dry ice in easy-to-handle 5 x 5 x 10 (127 mm x 127 mm x 254 mm) blocks. Compact and convenient the Alpheus Series BlockMaster has intuitive and ergonomic controls, which make it easy to operate. Its small footprint and light weight allow for easy transport and quick installation almost anywhere. Finally, its low energy consumption makes it a cost-effective piece of quality equipment. Features Small footprint and light weight allow for easy transport and quick installation almost anywhere Quick startup and shutdown period Ergonomic control panel is high-mounted for easy reach CO2 Block Size: 5 x 5 x 10 - max. weight 13.5 lbs - (127 mm x 127 mm x 254 mm - max. weight 6 kg) CO2 Inlet Pressure: psi (17-20 bar) Production Capacity: 360 lbs (164 kg) per hour 41

39 Engineered Systems Integrated Systems Integrated Systems combine and interface a Cold Jet Pel let iz er with one or more Cold Jet blasting systems and provide for con tin u ous, un in ter rupt ed, completely au to mat ed operations. Each Cold Jet Integrated Sys tem is custom engineered to meet specifi c customer re quire ments. Cold Jet has the unique capability to act as either a Prime Con trac tor or Sub-Contractor in designing, installing and supporting a complete man u fac tur ing work cell which may include not only the Cold Jet In te grat ed System, but also fl ex i ble automation, collection and con tain ment systems, and other production-line interfaces. We have installed and supported Integrated Systems in the semiconductor processing industry, the copier machine industry, the tire in dus try, the automotive OEM and aftermarket parts industry and the aerospace in dus try. Features Ability to run multiple nozzle stations Fully automated - no interruption of work to fi ll machine with dry ice pellets Works with robots or manual blasting Ideal for integration with a production line Operating pressure up to 300 psi (20.7 bar) (Pressure relief valve will be set at 140 psi (9.7 bar) unless otherwise specifi ed) Option Control System (Allen-Bradley, Siemens, Telemechanique) Automated Cleaning Booth This Automated Cleaning Booth has been designed for dry ice cleaning applications that require re pet i tive spray ing on similar sized parts, hour after hour, all week long. This booth is a quiet, soundproof enclosure with ad vanced micro-particle fi ltration and effl uent capture system to collect or reclaim the con tam i nant being re moved. Features External noise below 80 dba Fully integrated safety circuits and E-stops Double-glazed viewing window plus cabinet workspace lighting Positive pressure cabinet design Can be used with compressed air or nitrogen as blast propellant Nozzle path motion accomplished with off-the-shelf, easy to program and use, multiple axis industrial robot mounted inside the cabinet Cabinet can be constructed with slide-out trays, or a variety of parts loading and parts fi xture devices depending on the application Uses any of Cold Jet's single-hose blasting systems, or can be part of a Cold Jet in te grat ed system with pelletizer, blasting unit, and the cabinet combined Custom designed air handling and fi ltration Glove-box version available for manual blasting Cold Jet's single-hose blasting unit can be detached for use elsewhere in your plant when the cabinet is not in service 42 All systems are custom confi gured based on the application. Custom con fi g u ra tions are available through your Cold Jet Representative.

40 Engineered Systems FLASHJET The patented FLASHJET coatings removal process utilizes highly sophisticated tech nol o gy to strip all types of coatings from both composite and metallic substrates without damage. This system is approved by both the Department of Defense and the Federal Aviation As so ci a tion for military and commercial air craft.* Features Three simultaneous processes: Pulsed-light energy ablates the coating Dry ice cools and cleans the surface Effl uent is vacuumed into a capture system Results Effi cient coatings removal Reduced operating costs Safe for metallic and composite substrates Low volume of residual effects Minimal safety requirements * This is a specialized joint venture between Cold Jet and Flash Tech, Inc. All systems are custom confi gured. More information is available through our FLASHJET specialist. 43

41 Safety Accessories Acoustical Screen - Part #: 4K0017 or 4K with free standing frame 4' x 8' (1.2 m x 2.4 m) screen The screen has a Noise Reduction Coeffi cient (NRC) of 0.85 and a Sound Transmission Class (STC) of 29 dba Can reduce noise exposure up to 12 dba Optional mounting assembly Fire Sleeve Part #: 4N0094-3/4 (1.9 cm) ID 4N (2.5 cm) ID 4N /4 (3.2 cm) ID Recommended if blast hose may be exposed to temperatures above 180 o F (82.2 o C) Allow 4" to 20" (1.2 m to 6.1 m) coverage for area of blast hose subject to high heat Whip Check - Part #: 4Z0051 For each length of hose ordered, order one Whip Check Safety Kit - Part #: 2Z0001 Meets OSHA requirements for operator noise protection (with the use of properly rated and worn earplugs) Kit includes: 100 sets of ear plugs, 2 ear protectors, an eye protector shield, gloves and a dry ice pellet scoop or handler 44

42 Services Customer Support Support Hotline (24 hours a day, 7 days a week) East Coast (ext. 397) West Coast (ext. 229 or 235) Europe (0) Services You Can Depend On Cold Jet, LLC has earned its reputation as the industry leader in patented dry ice technology by de liv er ing high-quality products, exceptional service and unparalleled sup port. At Cold Jet we focus on what is important - and supporting dry ice. Service Center Our technicians are factory trained to install your system(s), and to provide product main te nance and repair. The service centers are located in our man u fac tur ing facilities, ensuring that our technicians are current on the latest technology and enhancements avail able from Cold Jet. This also allows easy access to our highly skilled engineering de part ment for their input on complex questions and custom confi guration requirements. Service and Maintenance Programs Cold Jet offers proactive and pre ven tive services. Our professionals can: handle complex installations and provide training conduct site surveys to ensure that systems are properly installed and make rec om men da tions in order to maximize performance administer regularly scheduled maintenance programs to keep your system work ing at maximum effi ciency. answer questions and provide support when standard troubleshooting tips are not suf fi cient provide temporary replacement systems while your system is being repaired at our facility. Whenever possible or when necessary they will handle repairs on-site. Spare parts and accessories The members of Cold Jet's customer support team are experts in maximizing the performance of your sys tem(s). Certain applications benefi t from spe cial ized confi gurations. Our highly-trained customer support team is avail able to answer questions and provide direction on which confi guration will result in the best possible performance for you. Our professionals will: recommend appropriate accessories to maximize performance. fulfi ll spare part orders and, if necessary, handle the installation. 45

43 Services Delivery Contact Information: M-F 8:30 a.m - 5:00 p.m. (Eastern Standard Time) East Coast M-F 8:30 a.m - 5:00 p.m. (Pacific Standard Time) West Coast Quality You Can Depend On Cold Jet, LLC pioneered and patented the technology that produces high-density dry ice pellets. The quality of Cold Jet pellets signifi cantly improves the performance of dry ice blasting systems as the high-density pellets sublimate more slowly and have an increased blasting aggression over other comparable dry ice media. We con tin u al ly mon i tor our pro duc tion facilities to ensure that produce and distribute only the highest quality dry ice products. The Product Cold Jet, LLC manufactures and distributes the highest quality high-density: dry ice pellets nuggets block Distribution is available locally as well as globally. Call for information about de liv ery in your area. Service Programs Our trained technicians will make recommendations on which media will max i mize per for mance for your application. The dry ice division manages blanket orders, recurring orders and onetime orders. We will co or di nate: 48-hour delivery to ensure fresh ice delivery schedules that work with holidays and plant shutdowns delivery of media that coincides with the installation of new blasting systems job logistics for contractors 46

44 Services Cold Jet Solutions Contact Information: M-F 8:30 a.m - 5:00 p.m. (Eastern Standard Time) DRY-ICE ( ) (513) (Cincinnati, OH) (706) (Augusta, GA) An integral part of our full service offering is Cold Jet Solutions. Cold Jet Solutions provides dry ice blast cleaning services and short-term rental programs across a broad spec trum of in dus tri al and commercial cleaning and coatings removal applications. We provide all the benefi ts of dry ice blast clean ing for one-time and short-term projects to those customers whose needs do not necessitate owning the equipment. Contract Cleaning Services Using Cold Jet's patented single-hose blast technology, Cold Jet Solutions provides contract cleaning services performed by factory-trained technicians, who are certifi ed in industry standard safety practices and procedures. The work is han dled either at the cus tom er's site or in one of our Cold Jet Solutions Cleaning facilities. Onsite cleaning includes personnel, labor, transportation, equipment, dry ice, accessories, support equipment and personal protection equipment. Upon request, we will provide each customer with a Proof of Liability Certifi cate and a Worker's Compensation Certifi cate. All work is handled at the cus tom er's con ve nience, in clud ing after hours and week ends. Cus tom er ap pli ca tion tests are han dled on-site for a nominal fee that is applied towards future business. In-house cleaning includes verifying and documenting the receipt and shipment of the cus tom er's parts which are always handled per the customer's specifi cations. Our Loveland, OH and Augusta, GA facilities are fully equipped to han dle a range of cleaning and stripping applications, in clud ing fast turn around and emer gen cy jobs. Cus tom er ap pli ca tion tests are han dled at our clean ing facility free of charge. Short-Term Rentals Cold Jet Solutions offers short-term rentals of our dry ice blasting systems. A complete sys tem, confi gured to meet the needs of the application, is delivered to the fa cil i ty, in clud ing the nec es sary dry ice to get started. Com pre hen sive training of on-site personnel is avail able with all short-term rentals. 47