Accessory Connection Module Installation Guide

Transcription

1 This document describes how to install the Accessory Connection Module (ACM) (NTMN71xx). The ACM is an optional hardware module that you install into the telephone footstand. The ACM provides a port, or ports, to connect the accessory cartridge interface. The M3902 has one accessory port. The M3903, M3904, and M3905 have two accessory ports. Note: The M3901 does not support the ACM. The plug-in cartridge allows the M3900 Series Digital Telephones to use the following accessories: Meridian External Alerter and Recording Interface (MEARI) Personal Directory PC Utility (M3904 and M3905) Full Duplex Handsfree (FDHF) cartridge (M3904 Phase III only) Analog Terminal (ATA) Computer Telephony Integration (CTIA) Note: The Meridian SL-100 does not support the CTIA. Figure 1: Accessory Connection Module (ACM) Footstand ACM ribbon cable ACM Rectangular opening for ACM Installation Telephone and footstand N Page 1 of 5 Standard 2.00

2 Installing the Accessory Connection Module 1. Press the release latch on the back of the telephone. 2. Pull the footstand away from the back of the telephone. 3. Disconnect the line cord from the base of the telephone. 4. Move the telephone down 7 mm (1/4 inch), then use the hinges to swing the telephone footstand away from the base of the telephone. 5. Snap the ACM into the rectangular opening in the telephone footstand. Ensure that it is snapped in securely. 6. Plug the ACM cable connector into the back of the telephone. 7. Place the ACM attached ribbon cable into the track running down the telephone base. 8. Snap the plastic cable cover in place over the ACM ribbon cable. 9. Connect the line cord into the base of the telephone. 10. Connect the hinges to the telephone base and swing the footstand back in place. 11. Snap the footstand into a fixed position. 12. Return the telephone to its original position. You can access the ACM connector ports through a cutout on the base of the footstand. When you are ready to attach an accessory, insert your selected accessory cartridge into the ACM. There are two ports at the back of the telephone footstand on the M3903, M3904, and M3905. Each port can support one cartridge accessory. The M3903, M3904, and M3905 can use a maximum of two cartridge accessories. The M3902 supports one cartridge accessory. Accessory compatibility The ACM provides up to two port connections. Some port types are not compatible. For example, you cannot simultaneously use two data accessories that require a serial port. The shape and size of the plug-in accessory cartridge prevents you from accidentally connecting incompatible accessories. If you are purchasing two accessory cartridges, refer to Table 1 on page 3 to see if you can use the two accessories with the M3903, M3904, or M3905 at the same time. The M3902 supports only one accessory. See Table 1 on page 3 before you purchase optional hardware accessories. Note: Not all accessories are supported on all telephones in the M3900 Series portfolio. Contact your Nortel distributor for further information. Standard 2.00 Page 2 of 5 N

3 Figure 2: Accessory cartridge Latch RS232C Table 1: Accessory compatibility ATA CTIA PC Utility FDHF MEARI Analog Terminal (ATA) N/A Yes Yes No Yes Computer Telephony Integration (CTIA) Yes N/A Yes 1 N/A Yes Personal Directoty PC Utility Yes Yes 1 N/A Yes Yes Full Duplex Handsfree (FDHF) No 3 Yes Yes N/A Yes 2 Meridian External Alerter and Recording Interface (MEARI) Yes Yes Yes Yes 2 N/A Key-Based Accessory (KBA) Yes Yes Yes Yes Yes Display-Based Accessory (DBA) Yes Yes Yes YeS Yes Note 1. If either the CTIA or the PC Utility cartridge is installed, no additional cartridge is required. The applicable software may be purchased separately. Note 2. FDHF works with the MEARI external alerter functionality; however, the MEARI cannot be used for recording when FDHF is in operation. Note 3. FDHF and ATA can be interchanged but cannot be used simultaneously. N Page 3 of 5 Standard 2.00

4 Wall transformers You need a wall transformer that connects to the ACM to use accessory cartridges. Contact your Nortel distributor for further information. The ACM requires one of the following wall transformers to power the accessory cartridges: 110 V wall transformer (NTMN80AA) EU (EMEA) 230 V wall transformer (NTHC09AA) UK 230 V wall transformer (NTHC08AA) To connect the wall transformer: 1. Insert the accessory cartridge into the ACM. Refer to your accessory installation guide. 2. Plug the wall transformer into an electrical outlet. 3. Connect the adapter plug, attached to your transformer, into the wall jack. 4. Connect the six-conductor line cord from the telephone to the adapter jack attached to the wall transformer. Figure 3: and wall transformer connections for North America To IDF jack 6-conductor line cord from telephone plug Plug Jack Wall transformer (110 V or 220 V) Standard 2.00 Page 4 of 5 N

5 Figure 4: EMEA transformer Plug Jack Wall transformer (110 V or 220 V) N Page 5 of 5 Standard 2.00