Compatibility Report. Comtrol IO-Link Master. Microsonic sks-15/cf Proximity Sensor

Transcription

1 Compatibility Report Comtrol IO-Link Master Microsonic sks-15/cf Proximity Sensor

2 Contents Contents... 2 Test Report Overview... 3 IO-Link Master - IO-Link Diagnostics Page... 4 Configuring IO-Link Settings... 5 After Configuring Port-Friendly Names... 7 Setting Up Passwords... 8 SKS-15/CF Configuration Loading IODD Files Verifying that the Correct IODD Files Are Loaded Changing Parameters on the SKS-15/CF with the GUI Changing Parameters Using the ISDU Interface Using the Automatic Data Storage Feature Clearing Data Storage Using the Manual Data Storage UPLOAD Feature Resetting the Sensor to Factory Defaults Using the Manual Data Storage DOWNLOAD Feature Using the Device Validation Feature Incompatible Device Attached to Port /1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 2

3 Test Report Overview The Microsonic SKS-15/CF proximity sensor operates properly with the Comtrol IO-Link Master. This report contains the following topics: IO-Link Master IO-Link Diagnostics page Configuring IO-Link settings Setting up passwords Configuring the sensor with the IODD file Changing sensor parameters with the ISDU Interface Resetting the sensor back to factory defaults Using the Data Storage feature (automatic and manual) Using the Device Validation feature The sensor was tested using the IO-Link Master DR-8-EIP (DIN rail IP20) with the illustrated images. The IO-Link Master firmware is field upgradable. This report does not illustrate all Comtrol IO-Link Master features, such as: EtherNet/IP and Modbus/TCP configuration, uploading the latest software, or network configuration. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 3

4 IO-Link Master - IO-Link Diagnostics Page Upon connection to the IO-Link Master, the SKS-15/CF immediately displays in the IO-Link Diagnostics page without any configuration. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 4

5 Configuring IO-Link Settings There is no configuration required to getting the IO-Link device operating. It is not even necessary to configure the Minimum Cycle Time, as the IO-Link Master negotiates the required Cycle Time with each IO-Link device. This example shows configuring friendly port names and implementing Automatic Data Storage. The Device Validation and Manual Data Storage features are discussed later in the report. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 5

6 You can refresh the IO-Link Master to view that Automatic Data Storage was implemented or view the IO-Link Diagnostics page as is illustrated in the next subsection. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 6

7 After Configuring Port-Friendly Names The IO-Link Diagnostics page now displays friendly the Port Name and shows that the Automatic Data Storage feature is enabled. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 7

8 Setting Up Passwords The IO-Link Master ships from the factory without passwords and administrative permissions are granted. You can use the Advanced Accounts page to set up passwords for the IO-Link Master. Admin, Operator, and User permissions are defined in the help system on the Accounts page. Page Admin Operator User Log-in Yes Yes Yes Home Yes Yes Yes Diagnostics - All Yes Yes Yes Configuration - IO-Link Settings Yes Yes View-only Configuration - Digital I/O Settings (Applicable models) Yes Yes View-only Configuration - Digital I/O Settings Yes Yes View-only 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 8

9 Page Admin Operator User Configuration - EtherNet/IP Settings Yes Yes View-only Configuration - Modbus/TCP Yes Yes View-only Configuration - PROFINET IO Yes Yes View-only Configuration - Network Yes View-only No Configuration - Misc Yes Yes Yes Configuration - Clear Settings Yes No No Advanced - Software Yes No No Advanced - Accounts Yes No No Advanced - Log Files Yes Yes Yes Advanced - Licenses Yes Yes Yes Attached Devices - IO-Link Device Description Files Yes Yes View-only Attached Devices - IO-Link Device Configuration Summary Yes Yes View-only Attached Devices - IO-Link Device - Port Yes Yes View-only 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 9

10 SKS-15/CF Configuration You can use the Comtrol IO-Link Master to configure the IO-Link device. When an IODD file is loaded on the IO-Link Master, you can use the GUI on the top of the IO-Link Device Port page to change parameter settings. If an IODD file is not loaded, you can use the ISDU Interface on the bottom of the IO-Link Device Port page This section discusses the following topics: Loading IODD files Verifying that the correct IODD file is loaded Changing IO-Link device parameters using the GUI Loading IODD Files IODD file packages must be unzipped and the appropriate files located and re-zipped or loaded individually. 1. Click Attached Devices IODD Files. 2. Click the UPLOAD FILE button. 3. Click the CHOOSE FILE button. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 10

11 4. Select the xml file to upload and click the Open button. 5. Click the Upload button. 6. The IODD Files page now displays the IODD file loaded on the IO-Link Master. The page notifies you that there are images missing. This does not affect functionality but if the images are not loaded, the device image and logo are not displayed on the Port page for the sensor. You can load the image files individually by clicking the check box in the right column and using Steps 2-5 for the image files. Optionally, you can zip the three files and load it. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 11

12 7. If you want to view the xml file, click the corresponding IODD FILENAME in the table. 8. Optionally, click the hyperlink to view the xml file in your browser. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 12

13 Verifying that the Correct IODD Files Are Loaded Use the IO-Link Device Configuration Summary page to verify that the correct IODD files for the attached IO-Link devices have been loaded on the IO-Link Master. The correct file is loaded if an xml file name displays in the IODD Name field. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 13

14 Changing Parameters on the SKS-15/CF with the GUI 1. The SKS-15/CF displays as expected in the PORT page. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 14

15 2. Click the EDIT button to make parameter changes. In this example, these parameters were changed: Index 75 = 350 (default = ) Index 64 = 160 (default = ) Index 65 = 173 (default = ) 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 15

16 3. Click the SAVE button to observe that the settings were changed. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 16

17 Changing Parameters Using the ISDU Interface This shows using the IO-Link ISDU Interface to change configuration parameters. Please note: You must enter the decimal value for the ISDU Block Index and ISDU Sub-index. You must enter the hexadecimal value in the interface. The following screenshots do not illustrate the system responses. The IO-Link Master responds with a command executed notification. The following shows how to use the IO-Link ISDU Interface to change IO-Link device configuration parameters. 1. Expand the IO-Link Device ISDU Interface at the bottom of the page. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 17

18 The following images do not display the complete web page. 2. Verify that the sensor responds to queries. a. Enter the ISDU Block Index. b. Click GET. 3. Change Index 67 to 2 and click SET. 4. To verify the parameter change, click the REFRESH button. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 18

19 5. You can review the process data by selecting Process Data in the drop list next to Port 1. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 19

20 Using the Automatic Data Storage Feature The following examples illustrate how use the Automatic Data Storage feature. The proximity sensor was configured in the previous discussion. In this section, we will first disable Automatic Upload Data Storage, reset the sensor back to factory defaults, and then use the Automatic Download Data Storage feature to restore the previously configured parameters. This example automatically uploads data storage using the previous values. 1. Access the Configuration IO-Link Settings page. 2. Click the EDIT button on the corresponding port. 3. Click Automatic Upload Enable to Off. 4. Click SAVE. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 20

21 5. In this step, we will reset the sensor back to the factory default settings using the GUI. a. Click Attached Devices Port 1. b. Click the Command button. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 21

22 c. Click the Restore Factory button. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 22

23 d. Click the Ok button to refresh the page so that you can verify the changes. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 23

24 e. Notice that the parameters have returned to their factory default settings. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 24

25 6. Click Configuration IO-Link Settings. a. Click the EDIT button. b. Set Automatic Download Enable to On. c. Click SAVE. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 25

26 7. You can return to the Port page and verify that the parameters have been uploaded. Note the yellow highlighted parameters were downloaded. Parameter changes that are determined by the IODD file and made in the GUI are automatically uploaded to the IO-Link Master but parameter changes made using the ISDU Interface are only uploaded if you use Index 2 to trigger an upload. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 26

27 Clearing Data Storage This is how you can clear the data storage on an IO-Link Master port. 1. Click the Configuration IO-Link Settings. 2. Click the EDIT button. 3. In this example, we also need to change Automatic Download Enable to Off. 4. Click the Clear button. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 27

28 5. Click the Continue button. 6. Click the Ok button to the Done message. 7. Click SAVE. 8. Notice that the Storage Contents is now empty. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 28

29 Using the Manual Data Storage UPLOAD Feature The section shows how manual data storage works. The sensor contains the previously configured settings. 1. If necessary, click Configuration IO-Link Settings. 2. Click the EDIT button. 3. Click the UPLOAD button. 4. Click the CONTINUE button. 5. Click the OK button to the Done message. 6. Click the SAVE button. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 29

30 7. Notice that there is now Storage Contents. 8. The next step is to return the sensor to the factory default settings. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 30

31 Resetting the Sensor to Factory Defaults The sensor can be returned to the factory defaults. 1. Click Attached Devices Port 1 (in this example). 2. Click the Command button. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 31

32 3. Click the Restore Factory button. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 32

33 4. Click the Ok button to refresh the table and then you can verify that the parameters returned to their factory default values. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 33

34 Using the Manual Data Storage DOWNLOAD Feature This section shows how the manual download data storage feature works. 1. Click Configuration IO-Link and then click the EDIT button. 2. Click the DOWNLOAD button. 3. Click the CONTINUE button. 4. Click the Ok button when the Done message appears and then click the CANCEL or SAVE button. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 34

35 5. Click Attached Devices Port 1 to verify that the parameters were downloaded on the sensor. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 35

36 Using the Device Validation Feature The SKS-15/CF supports Compatible Device Validation. This report does not illustrate Identical Device Validation because serial numbers are required to illustrate Identical Device Validation. Incompatible Device Attached to Port 1. In the IO-Link Configuration page, click EDIT, set Device Validation mode to Compatible. 2. Click the GET ATTACHED button. 3. Click SAVE. 4. Remove the SKS-15/CF and connect another IO-Link device (not a SKS-15/CF). 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 36

37 5. The IO-Link LED on the IO-Link Master is now flashing red to indicate that an incompatible device is connected to the port. In addition, the IO-Link Diagnostics page displays that an incompatible device is attached to the port. Last Events towards the bottom of the Diagnostics page also indicates that the wrong sensor is attached. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 37

38 6. Re-attach the SKS-15/CF and notice that it immediately begins operating. 8/1/2017 Comtrol IO-Link Master Microsonic sks-15/cf Page 38