Version /04/27

Size: px

Start display at page:

Download "Version /04/27"

Mabel Snow
5 years ago
Views:

EasyBuillder Pro Rellease Note Version 1.1.0 2012/04/27 [New Features] 1.

1 EasyBuillder Pro Rellease Note Version /04/27 [New Features] 1. For Option List object [Source of item data], if [Item address] is selected, the way to display the content can be selected from [Reverse high / low byte] or [UNICODE]. a Select [Reverse high / low byte]: If set Control Address to LW-10, [Address + 1] will be LW-11, for setting the number of items. Select [Reverse high / low byte] for Item Address, and set the start address to LW-15. Set the length of each item to 10 words, if two items are added, the address should set to LW-15 and LW-25.

In simulation, enter the number of items to be added

LW-15 and LW-25 which specify the display method.

it shows that the high byte and low byte are reversed

2 In simulation, enter the number of items to be added in LW-11, and enter the content to be displayed in LW-15 and LW-25 which specify the display method. Enter 1 in Control Address LW-10 to update item data, it shows that the high byte and low byte are reversed on Option List. b Select [UNICODE]: Display item content in UNICODE.

Enter 1 in Control Address LW-10 to update item data, it shows that the data is displayed in UNICODE on Option List. 2. Macro Function INPORT2() added.

3 Select [Use UNICODE] for the object that displays item content. In simulation, enter the number of items to be added in LW-11, and enter the content to be displayed in LW-15 and LW-25 which specify the display method. Enter 1 in Control Address LW-10 to update item data, it shows that the data is displayed in UNICODE on Option List. 2. Macro Function INPORT2() added. INPORT2() can only be used for a Free Protocol device: short wresponse[16], receive_len, wait_time=20 INPORT2(wResponse[0], "Free Protocol", receive_len, wait_time) This function will check if data can be read via a communication port (COM port or Ethernet port). If there's no data read during the [turn around delay (ms)] set in system parameter settings, the function returns. When INPORT2() function reads data during turn around delay, it keeps reading until the end of the wait time (ms), if there's no upcoming data during the designated time interval, the function returns.

4 Or, if the length of the received data reaches the length declared in wresponse, the function returns. The variable, receive_len (in byte), stores the length of the data recived. 3. In Label Tag Library, the labels used by objects will be displayed in red font for easier checking.

4. When adding new languages to Label Tag Library, the text alignment and font size of the new languages on objects follow the settings of Language 1.

5 4. When adding new languages to Label Tag Library, the text alignment and font size of the new languages on objects follow the settings of Language 1. EX: Adding the third language when using two languages, the text of the third language displayed on the object will be the same to Language 1 in alignment and font size. 5. In System Parameter Settings, when changing HMI model to a smaller screen size, if [Resize objects] is not checked, a warning message will be displayed to prompt that the objects may be removed and can t be recovered. STEP1 STEP2 STEP3 6. For Numeric Input / ASCII Input objects Interlock function, [Grayed label when disabled] selection is added.

For Numeric Input / Display objects, the new selection [Center] is added to font alignment. 9.

6 7. For Event Log address, if set format to string, [UNICODE] and [Reverse low/high byte] display mode can be selected. 8. For Numeric Input / Display objects, the new selection [Center] is added to font alignment. 9. For Function Key objects [ASCII/UNICODE] mode, the new selections [Delete], [Left] and [Right] are added to remove or move the location of the cursor when designing keyboards.

[Right]:After entering a value, press, the cursor in the field will move to right. 10.

7 [Delete]:After entering a value, press Del, the data in the field will be deleted. [Left]:After entering a value, press, the cursor in the field will move to left. [Right]:After entering a value, press, the cursor in the field will move to right. 10. When adjusting the profile of an object, [Keep width/height ratio] selection is added. If checked, the ratio of width and height will keep the same, even when changing the size with a mouse. 11. To delete a macro that s already used in any object, a prompt dialog is displayed.

8 12. Alarm (Event) Log / Message tab, the number of watch addresses is increased to 8.

9 13. Data Sampling Clear Address and Hold Address can be set to ON or OFF. 14. When creating a Trend Display Object, go to [Channel] tab and check the channels, the ON or OFF state of the corresponding bit can control whether or not to display the channels.

10 15. For System Message Confirmation, the size of the prompting dialog can be set. 16. When creating an Option List Object, if set [Source of item data] to [Dates of historical data], the format of the date can set to YYYY/MM/DD.

confirmation dialog when defining those using non

2. Fix the Hold Control address to stay the same

The description of Event Management Address of

11 [Corrections] 1. Fix the display of [OK] and [Cancel] texts on confirmation dialog when defining those using non ASCII characters in System Message object settings. 2. Fix the Hold Control address to stay the same after decompiling Trend Display object. 3. The description of Event Management Address of Event Display object is modified. The function of the address is not changed, only the description.

12 4. Fix when using Macro nested loop, the outer loop will only be executed once. As shown below, for i = 0 to 20 will only be executed once. 5. Fix the font cause HMI crash, and enhance the efficiency of HMI operation. 6. Fix Numeric Input Object to correctly display when using different addresses to Read / Write.

Even when the language used is changed, the tag name will remain identical to the original setting. 9.

13 7. In Address Tag Library / System Reserved Registers, when select PLC (SIEMENS S7-300 MPI) for communication, the display will no longer blink. 8. Fix UAC address tag in the library and the tag set in object property. Even when the language used is changed, the tag name will remain identical to the original setting. 9. When selecting channels above 19 in Trend Display Object settings, if [Dynamic limits] is checked, On-line Simulation will no longer cause errors.

14 10. Fix not to show warning message when downloading if adding 64 Ethernet PLC devices in System Parameter Settings. 11. Fix Siemens S7-200 PPI communication outage when switching Term Mode to Run Mode or power up. 12. Fix when downloading projects, the i series screen display won t be shown. 13..Fix macro command writing error that occurs when writing recipe data to multiple databases. 14. When putting two trend curves together, the lines won t overlap and become one single straight line.

When using PLC device - MODBUS Server (COM/Ethernet) and communicate via

15 15. Fix the setting of Fast Selection Button in System Parameter Settings. The multi-language text can be center aligned. 16. When using PLC device - MODBUS Server (COM/Ethernet) and communicate via Ethernet, the mapping of the devices is fix to map correctly even when adding more devices.

When deleting the recipe folder under HMI memory directory, HMI will no longer

16 17. Fix Trend Display Channel Options, if [Dynamic limits] is selected, the address grid will be marked correctly, according to the address set. 18. When deleting the recipe folder under HMI memory directory, HMI will no longer crash when executing simulation. [New Drivers] 1. The following drivers are added: a. BACnet BACnet/IP

17 b. SSTC SSD Series c. MIKOM MX Series d. Haiwell PLC e. Trio MODBUS RTU, TCP/IP (Mode 7) 2. MODBUS RTU (0x/1x Range Adjustable) and MODBUS TCP/IP (0x/1x Range Adjustable) drivers now allow modifying the Maximum and Minimum address of 0x 1x Address Range. 3. When using MODBUS RTU driver, if error occurs, the error code replied by PLC will be stored in the address start from LW-9400 (LW-9400 for COM 1 device, LW-9401 for COM 2 device ). For the meaning of error codes, please refer to the content of MODBUS RTU protocol. 4. GE Fanuc Series (Ethernet) added address type W. 5. MODBUS TCP/IP driver allows setting the number of times to resend commands. When sending commands to PLC, if no replies received, the commands will be sent for the number of times set then display PLC No Response message after all attempts fail.

MODBUS RTU added address type 0x_single_coil (Word). 9.

18 6. Rockwell EtherNet/IP (CompactLogix) added Lx_DINT address format. 7. Beckhoff ADS/AMS (Ethernet) and Beckhoff Embedded PC drivers [ADS port] setting added new selection MODBUS RTU added address type 0x_single_coil (Word). 9. CAN Bus driver now supports cycle communication mode. 10. Siemens S (Ethernet) added address type USInt. 11. Siemens S7-300/ET200S (Ethernet) added address types MD_AnyAddr, DBDn_Anyaddr.

EasyBuilder Pro V Fixed the problem where macro function FLOAT2ASCII may do incorrect

EasyBuilder Pro V Fixed the problem where macro function FLOAT2ASCII may do incorrect Build 2014.12.08 Software Version:EasyBuilder Pro V4.10.07 Corrections EasyBuilder Pro 1. Fixed the problem where the address grid disappears when changing the size of EasyBuilder Pro editing window. 2.