MAG. Explorer. Reference for the latest revision of the Magnetek Explorer software

Size: px

Start display at page:

Download "MAG. Explorer. Reference for the latest revision of the Magnetek Explorer software"

Mabel Dean
6 years ago
Views:

1 MAG Explorer The Magnetek Explorer is a serial communication program used to work with the HPV 600, HPV900, HPV900 S2, and Quattro parameters via a computer s serial port The program can: 1. Transfer parameters from the PC to the drive (HPV 600, HPV 900, HPV900 S2 and Quattro) 2. Transfer parameters from the drive (HPV 600, HPV 900, HPV900 S2 and Quattro) to the PC 3. Compare two parameter files and report any differences 4. Save the parameters to a file 5. Edit parameter values on the PC 6. Print parameters with settings 7. Upload latest revision of Quattro software (Quattro only) This document describes the following functions: Connections and Start-up page 2 drive PC page 3 PC drive page 7 Print page 11 Create HTML file page 12 Edit Header page 13 Compare page 14 Open page 16 Save to Disk page 17 Navigating menus and changing parameters page 18 Uploading Quattro Firmware page 21 Installation of Magnetek Explorer page 26 Installation of Driver for HPV900 S2 page 28 Reference for the latest revision of the Magnetek Explorer software

2 WARRANTY Standard products manufactured by the Company are warranted to be free from defects in workmanship and material for a period of one year from the date of shipment, and any products which are defective in workmanship or material will be repaired or replaced, at the Company s option, at no charge to the Buyer. Final determination as to whether a product is actually defective rests with the Company. The obligation of the Company hereunder shall be limited solely to repair or replace, at the Company s discretion, products that fall within the foregoing limitations, and shall be conditioned upon receipt by the Company of written notice of any alleged defects or deficiency promptly after discovery and within the warranty period, and in the case of components or units purchased by the Company, the obligation of the Company shall not exceed the settlement that the Company is able to obtain from the supplier thereof. No products shall be returned to the Company without its prior consent. Products which the company consents to have returned shall be shipped prepaid f.o.b. the Company factory. The Company cannot assume responsibility or accept invoices for unauthorized repairs to its components, even though defective. The life of the products the Company depends, to a large extent, upon type of usage thereof and THE COMPANY MAKES NO WARRANTY AS TO FITNESS OF ITS PRODUCTS FOR THE SPECIFIC APPLICATIONS BY THE BUYER NOR AS TO PERIOD OF SERVICE UNLESS THE COMPANY SPECIFICALLY AGREES OTHERWISE IN WRITING AFTER PROPOSED USAGE HAS BEEN MADE KNOWN TO IT. This warranty does not apply to experimental products for which no warranty is made or given and Buyer waives any claim thereto. THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT LIMITED TO, ANY WARRANTY OF MECHANTIBILITY OR OF FITNESS FOR A PARTICULAR PURPOSE AND BUYER HEREBY WAIVES ANY AND ALL CLAIMS THEREFORE. LIMITATIONS IN NO EVENT SHALL MAGNETEK BE LIABLE FOR LOSS OF PROFIT, OF LIABILITY INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES WHETHER ARISING OUT OF WARRANTY, BREACH OF CONTRACT OR TORT. HPV and Quattro are trademarks of Magnetek, Inc. All rights reserved. No part of this publication may be reproduced or used in any form or by any means - graphic, electronic, or mechanical including photocopying, recording, taping, or information storage and retrieval systems - without written permission of the publisher Magnetek, Inc.

3 Table of Contents CONNECTIONS AND START-UP... 2 DRIVE PC TRANSFERRING PARAMETERS FROM THE DRIVE TO PC... 3 PC DRIVE TRANSFERRING PARAMETERS FROM THE PC TO DRIVE... 7 PRINT PRINT COPY OF PARAMETER LIST CREATE HTML FILE CREATE AN ELECTRONIC PARAMETER FILE EDIT HEADER EDIT THE HEADER FOR PARAMETER FILE COMPARE COMPARE TWO PARAMETER SETS (EITHER DRIVE OR FILE) OPEN OPENING A PARAMETER FILE FROM DISK SAVE TO DISK SAVING A CHANGED PARAMETER FILE TO DISK NAVIGATING MENUS AND CHANGING PARAMETERS Menu selection buttons Sub-menu selection buttons Parameter selection buttons FIRMWARE UPLOAD LOADING MOTOR SIDE SOFTWARE IN QUATTRO DRIVE FIRMWARE UPLOAD LOADING LINE SIDE SOFTWARE IN QUATTRO INSTALLATION OF MAG-EXPLORER INSTALLATION OF USB TO PORT DRIVER

of the HPV 600, HPV 900, HPV900 S2 or Quattro and the serial port (COM1 or

HPV2-CABLE): HPV900 S2. 2. From Windows execute Mag-Explorer.

4 Connections and Start-up 1. Ensure the proper electrical connections between the digital operator port of the HPV 600, HPV 900, HPV900 S2 or Quattro and the serial port (COM1 or COM2 or COM3 or COM4) of a Windows based computer. a. The following products use a straight DB-9 cable (Magnetek pn MAG-CABLE): HPV600, HPV900, and Quattro. b. The following product uses a USB A to USB mini B cable (Magnetek pn HPV2-CABLE): HPV900 S2. 2. From Windows execute Mag-Explorer.exe or double-click on the icon. 3. Select proper serial COMM port. Note: on HPV900 S2, a special driver is required to make the USB port appear to the computer to act as a COMM port. Troubleshooting tip If the following message appears Select a valid serial COMM port available on the PC 2

This process can be used for memory backup.

5 DRIVE PC transferring parameters from the DRIVE to PC DRIVE PC is the process of the HPV 600, HPV 900, or Quattro sending all of its parameter values (from a file with the extension.par) to a computer. This process can be used for memory backup. While the drive is running a motor, the only interaction allowed between the drive and Mag Explorer is the transferring of parameters from the drive to the computer. 1. Select the drive PC function 2. Select parameter file path and name 3

600, HPV 900, HPV 900 S2 or Quattro is powered on Check for proper Comm Port selection 4.

6 3. Parameter transfer Troubleshooting tip If the following message appears Attempt selection of Drive to PC again Check if cabling between PC and HPV 600, HPV 900, HPV 900 S2or Quattro is properly connected Ensure HPV 600, HPV 900, HPV 900 S2 or Quattro is powered on Check for proper Comm Port selection 4. Choose proper submenu legends If the parameters came from the HPV900 S2 drive, use HPV900 Series 2 defaults for the submenu legends 4

If the parameters came from either the HPV 600 or HPV 900, use HPV600/900 defaults for the submenu legends If the parameters came from a Quattro DC, use QUATTRO defaults for the

The sequence for each submenu is as follows: Click OK. The next window will appear asking if the user would like to modify the legend of the sequential button.

7 If the parameters came from either the HPV 600 or HPV 900, use HPV600/900 defaults for the submenu legends If the parameters came from a Quattro DC, use QUATTRO defaults for the submenu legends There is a third option for manually entering the submenu legends if the user chooses to go through each submenu naming as desired. The sequence for each submenu is as follows: Click OK. The next window will appear asking if the user would like to modify the legend of the sequential button. For example, the first button has the present legend of Drive-A1. If the user would like to change the legend, click Yes: Enter desired legend in the screen below: The latter two screens will occur for each A0 submenu and each C0 submenu. 5

8 5. The transferred parameters will then display 6

PC DRIVE transferring parameters from the PC to DRIVE PC DRIVE is the process of a computer sending all settable parameters (with the extension.par) to a HPV 600, HPV 900, or Quattro.

9 PC DRIVE transferring parameters from the PC to DRIVE PC DRIVE is the process of a computer sending all settable parameters (with the extension.par) to a HPV 600, HPV 900, or Quattro. This process can be used to set up the drive with a set of pre-configured parameters. IMPORTANT It is not recommended for the HPV 600, HPV 900, HPV 900 S2 or Quattro to be running a motor while transferring parameters from the PC to the drive PC drive. This could lead to a dangerous operating condition. 1. Select the PC drive function 2. Initiating parameter transfer to drive 7

Troubleshooting tip If the following message appears Attempt selection of PC to Drive again Check if cable between PC and HPV 600, HPV 900, HPV 900 S2, or Quattro is properly connected Ensure HPV

10 Troubleshooting tip If the following message appears Attempt selection of PC to Drive again Check if cable between PC and HPV 600, HPV 900, HPV 900 S2, or Quattro is properly connected Ensure HPV 600, HPV 900, HPV 900 S2 or Quattro is powered on Check for proper Comm Port selection 3. Parameter transfer Troubleshooting tip If the following message appears If window shows differences is minimum values, it maybe OK to proceed (since some default values are below the defined minimums) If window shows differences other than minimum values, look more closely at this 8

Troubleshooting tip If the following message appears Password protection on the drive must be disabled for parameters to be transferred to this drive PASSWORD LOCKOUT=disabled (U1)

software revision is not the same between the drive and the parameter file If the transfer continues, only the identifiable parameters will be transferred Troubleshooting tip If the

par being sent to the drive If the transfer continues, those parameters will stay at the original value and not change with the *.

11 Troubleshooting tip If the following message appears Password protection on the drive must be disabled for parameters to be transferred to this drive PASSWORD LOCKOUT=disabled (U1) Troubleshooting tip If the following message appears The units selection must be changed to match the parameter file (U3) Troubleshooting tip If the following message appears The software revision is not the same between the drive and the parameter file If the transfer continues, only the identifiable parameters will be transferred Troubleshooting tip If the following message appears Parameters exist in the current software version of the drive than do in the *.par being sent to the drive If the transfer continues, those parameters will stay at the original value and not change with the *.par file Troubleshooting tip If the following message appears Parameters occur in the *.par file that are not found in the drive software If the transfer continues, these parameters will not be sent Troubleshooting tip If the following message appears A parameter was changed and was not saved via Save to Disk function 9

12 4. Parameter transfer complete 5. Parameter transfer options Transfer filename.par to the Drive will send parameter file to drive after first checking the software version and parameter structure on the drive Resend will send parameter file to drive without first checking the software version and parameter structure on the drive. Note: the resend function will only be enabled after a successfully parameter transfer has occurred and is disabled if the drive is powered down or the cable is disconnected. This is most useful when actively editing parameters rather than using the digital operator. Exit returns to main screen 10

13 Print print copy of Parameter List 1. Select the Print function. This will print to the PC s defined default printer. After the selection has been made, Magnetek-Explorer will declare the following message: 11

14 Create HTML file create an electronic parameter file 1. Select the Create HTML file function. 2. Select HTML file path and name 12

15 Edit Header edit the header for parameter file 1. Select the Edit Header function. 2. Edit the header text 13

16 Compare compare two parameter sets (either drive or file) 1. Select the Compare function. 2. Comparing parameters to another parameter file. Select Compare to FILE and Browse for file on disk 3. Select parameter file path and name. 14

4. Comparing parameters to Drive parameters.

the following message appears Check if cable between PC and Drive Ensure the drive is

Once the parameter transfer is complete, Select Begin Comparison 6.

17 4. Comparing parameters to Drive parameters. Select Compare to Magnetek drive and Get PAR from serial port Troubleshooting tip If the following message appears Check if cable between PC and Drive Ensure the drive is powered on Check for proper Comm Port selection 5. Once the parameter transfer is complete, Select Begin Comparison 6. The parameter comparison is displayed The differences can be sent to either the default printer via Print Difference Report or an electronic HTML file Create HTML Difference Report 15

18 Open opening a parameter file from disk 1. Select the Open function 2. Select parameter file path and name 3. Parameter file will be displayed 16

Save to Disk saving a changed parameter file

Disk appears grayed out, it means you have

19 Save to Disk saving a changed parameter file to disk 1. Select the Save to Disk function Troubleshooting tip If the following Save to Disk appears grayed out, it means you have not made any changes to your loaded parameter file 2. Select parameter file path and name 17

20 Navigating menus and changing parameters 1. First, load parameters into the Mag Explorer via Open or drive PC 2. Navigating menus Menu selection buttons Used to select available menus 3. Navigating sub-menus Sub-menu selection buttons Used to select available sub-menus (first select menu) 18

Additionally, it shows the allowable minimum and maximum values.

21 4. Changing parameters Parameter selection buttons Used to select parameter to change (first select menu and sub-menu) Changing Numeric Parameter The window title shows parameter name as well as numeric format. Additionally, it shows the allowable minimum and maximum values. Troubleshooting tip If the following message appears, it means you tried to enter a parameter below the minimum allowable value Troubleshooting tip If the following message appears, it means you tried to enter a parameter above the maximum allowable value 19

22 Changing Selectable Parameter Selection choices will be shown Changed Parameters Changed parameters are shown in italics until they have been saved via Save to Disk function 20

23 Firmware Upload Loading Motor Side Software in Quattro Drive 1. Power up QUATTRO. 2. If wanted, upload the parameter set from the drive to Magnetek Explorer to be placed back in the drive after the new program is installed. To do this, see DRIVE PC transferring parameters from the DRIVE to PC on page 3. Save the file and proceed to step Power down QUATTRO. 4. Remove jumper from UPLD and NORM on JM13 located on the Motor Side PWM Control Board. See figure below for location of JM13 and the Motor Side PWM Control Board. A2-JM13 RS232 Motor Side PWM Control Board (A2) 5. Place the removed jumper between PRGM and UPLD on the same JM13 found in step Power up QUATTRO 7. Open MAG EXPLORER on the connected PC. 8. Click on the Firmware Upload drop down menu on the EXPLORER program. The Program Loader will display in a new window. Click reset to establish communication. The following screen will display: 21

24 9. Click File and choose the *.ldr file specific to the application. 10. Click Upload. A new window will appear asking if it is okay to erase flash click OK. File will upload. See below for a detailed view. NOTE: Clicking okay will erase the program and parameters currently held in the flash. Flash erasure is irreversible and must be followed by a program load operation. See DRIVE PC transferring parameters from the DRIVE to PC on page 3 to save those parameters before installing the new program. 11. When file is finished uploading, Mag Explorer will display the following screen: 12. Click Exit to exit the current screen after Explorer says Program Pass. 13. Power down QUATTRO 14. Reset the jumper on JM13 to it s original position (between UPLD and NORM) 15. Recycle power. Because defaulted values will be loaded into the drive, it is expected a number of faults will occur. Re-insert the parameters saved in step 3 by using the PC drive button in the upper middle portion of Magnetek Explorer. See PC DRIVE transferring parameters from the PC to the DRIVE on page 7. WARNING Use extreme care when uploading software. Stopping an upload or disconnecting the cable during an upload could corrupt the software and inhibit the users ability to upload software. 22

25 Firmware Upload Loading Line Side Software in Quattro 1. Connect RS232 port of computer to RS232 input to drive as shown in below. Open Magnetek Explorer. Note it is not necessary to save line side parameters since they are stored on the motor side control board. 2. Power down QUATTRO. 3. Move Ribbon Cable from JM3 on the Motor Side PWM Control Board (A2) to JM3 on the Line Side PWM Control Board (A1). Line Side PWM Control Board (A1) A1-JM3 Motor Side PWM Control Board (A2) A2-JM3 4. Remove jumper from UPLD and NORM on JM13 located on the Line Side PWM Control Board. See figure below for location of JM13 and the Line Side PWM Control Board. A1-JM13 RS232 Line Side PWM Control Board (A1) 5. Place the removed jumper between PRGM and UPLD on the same JM13 above 6. Power up QUATTRO 7. Open MAG EXPLORER on the connected PC. 23

8. Click on the Firmware Upload drop down menu on the EXPLORER program. The Program Loader will display in a new window. Click reset to establish communication.

File will upload. See below for a detailed view. NOTE: Clicking okay will erase the program and parameters currently held in the flash.

26 8. Click on the Firmware Upload drop down menu on the EXPLORER program. The Program Loader will display in a new window. Click reset to establish communication. The following screen will display: 9. Click File and choose the *.ldr file specific to the application. 10. Click Upload. A new window will appear asking if it is okay to erase flash click OK. File will upload. See below for a detailed view. NOTE: Clicking okay will erase the program and parameters currently held in the flash. Flash erasure is irreversible and must be followed by a program load operation. See DRIVE PC transferring parameters from the DRIVE to PC on page 3 to save those parameters before installing the new program. 11. When file is finished uploading, Mag Explorer will display the following screen: 24

27 12. Click Exit to exit the current screen after Explorer says Program Pass. 13. Power down QUATTRO 14. Reset the jumper on JM13 to it s original position (between UPLD and NORM) 15. Reset the ribbon cable JM3 to the original position in JM3 on the Motor Side Board (A2). 16. Recycle power. Because defaulted values will be loaded into the drive, it is expected a number of faults will occur. Re-insert the parameters saved in step 3 by using the PC drive button in the upper middle portion of Magnetek Explorer. See PC DRIVE transferring parameters from the PC to the DRIVE on page 7. WARNING Use extreme care when uploading software. Stopping an upload or disconnecting the cable during an upload could corrupt the software and inhibit the users ability to upload software. 25

program screen appears, it means the Magnetek Explorer program is already

28 Installation of Mag-Explorer 1. Execute MAG-Explorer_install.exe Troubleshooting tip If the following the Modify, repair, or remove the program screen appears, it means the Magnetek Explorer program is already installed. Select Repair option, if updating to the latest version 2. Start installation 26

29 3. Select destination folder 4. Installation will begin 5. Install complete 27

exe (item may be found on www.elevatordrives.

30 Installation of USB to Port driver 1. Execute CP210x_VCP_Win2K_XP_S2K3.exe (item may be found on 2. Agree to the license agreement of the SiLabs product 28

$It will automatically set itself to C:\SiLabs\MCU\CP210x 4.$

31 3. Select the destination Location for the program. It will automatically set itself to C:\SiLabs\MCU\CP210x 4. The driver is now ready to the installed. Select install on the next screen: 29

32 5. The installation screen will display with the setup status 6. Install is complete 7. Connect the computer to the HPV900 S2 drive using the USB A male to USB mini B cable. 30

33 8. On the computer, navigate to the Device Manager. The device manager will show an unspecified device of the USB to UART Bridge Controller 9. Double click on the unspecified device to obtain the following screen 31

34 10. Select the Properties button at the bottom of the Hardware tab in the USB to UART Bridge Controller Properties window 11. With the new window displayed, select Update Driver to display the following screen: 32

35 12. Click on Browse my Computer for Driver software and make the following selection: 13. Driver installation is complete 33

38 MAG Explorer Data subject to change without notice. HPV and Quattro are trademarks of Magnetek, Inc. Magnetek Elevator Products N50 W13775 Overview Drive Menomonee Falls, Wisconsin (800) , (262) , FAX (262) Magnetek Elevator Products - Europe 20 Drake Mews, Crownhill Milton Keynes, Bucks MK8 0ER UK +44(0) , FAX +44(0) TM Magnetek, Inc. 8/10 rev 02

The HPV Explorer is a serial communication program used to work with the HPV 600/900 s parameters via a computer s serial port

Explorer The HPV Explorer is a serial communication program used to work with the HPV 600/900 s parameters via a computer s serial port The program can: 1. Transfer parameters from the PC to the drive