USB Image.NET- Creating a Boot USB Hard Drive 2013

Transcription

1 USB Image.NET - WINPE 5.x - Creating a Boot USB Hard Drive Contents General Requirements... 2 Assumptions... 2 Further Requirements... 2 Method 1:... 3 Preparing your USB Hard Drive/Key... 3 Method 2:... 4 Preparing your USB Hard Drive/Key... 4 Cleaning and Creating Partitions... 4 Setting up WINPE for booting on the USB Hard Drive... 5 Further Setup Tasks... 6 Installing USB Image.NET to your USB Hard Drive... 6 Adding WIM/DISM and GHOST to your USB Image.NET install... 7 End of Procedure... 8 Copyright 2013 USB Image.NET Page 1

2 General Requirements Assumptions - It is assumed you have already run through the guide titled USB Image.NET- Getting Started Guide and have a copy of your winpe.wim file. - It is also assumed you have a copy of Windows ADK installed. Further Requirements - A USB Hard Drive will be required. This can be a Hard Drive or USB Key. Copyright 2013 USB Image.NET Page 2

3 Method 1: This first method for setting up and configuring your WINPE.WIM and USB Hard Drive is far easier than the second method. Both methods are included and Method 1 should be tried first. Method 1 uses Windows ADK s new method for creating Bootable USB Disks and also allows for UEFI boot. Note that some older PCs are not compatible with UEFI and in this case Method 2 may be best to use. Preparing your USB Hard Drive/Key 1. In the start menu, open Start>All Programs>Windows Kits>Windows ADK> Deployment and Imaging Tools Environment as a local administrator. You will be shown the Deployment Tools Command Prompt. 2. In this new window, type the below command: copype x86 C:\WinPE_x86 This command creates a working copy of the Windows PE files. You can specify either x86, amd64, or arm just match the machine type with your already created WINPE.WIM file. 3. Copy your WINPE.WIM file (that you have already created) to the below directory: C:\winp_x86\media\sources 4. In the directory C:\winp_x86\media\sources delete the boot.wim file. 5. In the directory C:\winp_x86\media\sources rename the file winpe.wim to boot.wim. 6. To install Windows PE to the USB drive, use the below command: Note: X: in the below refers to your USB drive letter. This command will also format your USB Disk Drive MakeWinPEMedia /UFD C:\WinPE_x86 X: Copyright 2013 USB Image.NET Page 3

4 Method 2: Preparing your USB Hard Drive/Key Cleaning and Creating Partitions NOTE: USB Image.NET and its developers do not hold any responsibility for loss of data using this guide or USB Image.NET. From Windows, open a new command prompt by following the below: 1. Go to Start>All Programs>Windows System and right click Command Prompt. Choose Run as Administrator. 2. In the command prompt, type DISKPART. 3. Once DISKPART has loaded, type list disk. This command will show a list of all hard drives currently plugged into your PC. Check the size of the disks and match the correct size to the size of your USB Hard Drive and note the disk number. If you are unsure, do not proceed until you can find the correct drive. 4. Type select disk x replacing the x with your disk number. 5. Type clean to wipe the disk. 6. Type create part prim to create a single partition. 7. Type select part 1 8. Type assign letter=x where x is your next available drive letter in your system. 9. Type active 10. Type format fs=ntfs quick 11. Type exit 12. Your disk is now formatted correctly for USB Image.NET and WINPE to be installed. Copyright 2013 USB Image.NET Page 4

5 Setting up WINPE for booting on the USB Hard Drive 1. Copy your WINPE.WIM image file to C:\WINPE\WINPE.WIM. 2. Copy the contents of the C:\Program Files (x86)\windows Kits\8.1\Assessment and Deployment Kit\Windows Preinstallation Environment\x86\Media folder to your USB Hard Drive. Note: you can delete any language folders that are not required. 3. Create the x:\sources folder where x is your USB Hard Drive letter. 4. Copy the winpe.wim file in c:\winpe to x:\sources where x is your USB Hard Drive letter. 5. Rename the winpe.wim file in x:\sources to boot.wim where x is your USB Hard Drive letter. 6. Copy the etfsboot.com file from C:\Program Files (x86)\windows Kits\8.1\Assessment and Deployment Kit\Deployment Tools\x86\Oscdimg to x:\ 7. Go to Start>All Programs>Windows Kits>Windows ADK and right click Deployment and Imaging Tools Environment. Choose Run as Administrator. 8. Once in the new window, type bootsect /nt60 x: where x is your USB Hard Drive letter. 9. WINPE is now setup to boot from your USB Disk. Copyright 2013 USB Image.NET Page 5

6 Further Setup Tasks Installing USB Image.NET to your USB Hard Drive Run the downloaded and licensed installer for USB Image.NET and install to your USB Hard Drive root directory. Copyright 2013 USB Image.NET Page 6

7 Adding WIM/DISM and GHOST to your USB Image.NET install As WIM/DISM, Ghost and other programs used by USB Image.NET are copyright and owned by external companies to USB Image.NET, we cannot provide a copy of these files with the USB Image.NET installation. If you don t own a copy of these files (WIM/DISM and 7-zip are free) they are not required unless you wish to use the functionality they provide. 1. Once the install is complete, the WIM/DISM and Ghost tools (if required) need to be copied to the Plugins folder under x:\usb Image Files\Plugins where x is your USB Hard Drive letter. 2. Navigate to x:\usb Image Files\Plugins\GHO Tools\Ghost and copy the below suggested Ghost files to the directory: ghost32.exe ghostexp.exe ghost32.pip (if available) NOTE: If you are using WINPE 64bit you must download the GHOST64.EXE and rename to GHOST32.EXE. 3. Copy the files from C:\Program Files (x86)\windows Kits\8.1\Assessment and Deployment Kit\Deployment Tools\x86\DISM to x:\usb Image Files\Plugins\WIM Tools\ImageX 4. Copy the files from C:\Program Files (x86)\windows Kits\8.1\Assessment and Deployment Kit\Deployment Tools\x86\BCDBoot to x:\usb Image Files\Plugins\WIM Tools\BCD 5. Copy any required programs to x:\usb Image Files\Programs. See USB Image.NET- Programs Folder Guide for further information. Copyright 2013 USB Image.NET Page 7

8 End of Procedure Once complete, you should be able to boot a PC with the new WINPE/USB Image.NET USB Hard Drive. Copyright 2013 USB Image.NET Page 8