Push Button Switch for LED lighting with built in multi-way control

Size: px

Start display at page:

Download "Push Button Switch for LED lighting with built in multi-way control"

Cori Hunter
5 years ago
Views:

1 Setup Functions Guide MMSW/PB Push Button Switch for LED lighting with built in multi-way control DIGINET.NET.AU

2 Switch Setup The LEDsmart + push button switch has a number of useful functions which can easily be set up by entering setup mode and following three easy steps. It is recommended that the MAXIMUM BRIGHTNESS is always setup. The other settings are optional, depending on the application. To set the maximum brightness now, go to the next page. Switch Setup Functions Function See Part Entering Setup Mode Setting Maximum Brightness Setting Soft Start Mode Setting Off State LED Feature Setting MultiMate Mode Factory Defaults Reset A B C D E F A: Entering Setup Mode If the switch has been powered up for LESS THAN 15 MINUTES see A1. If the switch has been powered up for MORE THAN 15 MINUTES see A2. Once in Setup Mode, options are selected by a series of clicks of the push button. Each click should be within 1 second of the previous click. 2

A1: Switch has been powered up via mains 240Vac for LESS THAN 15 MINUTES Press and hold the button for 10 seconds Note: Connected lights will dim up or down, this

This indicates that the switch is now in Setup Mode Note: If more than one LEDsmart + switch is connected in parallel, all these switches will now enter setup mode.

Go to the relevant setup function instructions A2: Switch has been powered up via mains 240Vac for MORE THAN 15 MINUTES Press and hold the button for 30 seconds

Indicators will blink ON/OFF twice per second. Go to the relevant setup function instructions 3

3 A1: Switch has been powered up via mains 240Vac for LESS THAN 15 MINUTES Press and hold the button for 10 seconds Note: Connected lights will dim up or down, this is normal Push Button Switch The white LED Indicators will blink ON/OFF twice per second. This indicates that the switch is now in Setup Mode Note: If more than one LEDsmart + switch is connected in parallel, all these switches will now enter setup mode. The blink ON/OFF will also be seen on all other LEDsmart + switches connected in parallel The switch is ready for the settings to be adjusted as required. Go to the relevant setup function instructions A2: Switch has been powered up via mains 240Vac for MORE THAN 15 MINUTES Press and hold the button for 30 seconds Note: This resets the Setup Entry time back to 10 seconds (for the next 30 minutes) Note: Connected lights will dim up or down, this is normal The white LED Indicators will blink ON/OFF twice per second. This indicates that the switch is now in Setup Mode Note: If more than one LEDsmart + switch is connected in parallel, all these switches will now enter setup mode. The blink ON/OFF will also be seen on all other LEDsmart + switches connected in parallel The switch is ready for the settings to be adjusted as required. Go to the relevant setup function instructions 3

4 B: Setting Maximum Brightness The maximum brightness level provided by the switch can be set to suit customer requirements. Note that when lamps are near to full brightness, it is difficult to see changes in dimming level. Therefore, when setting up maximum brightness, it is recommended that the lamp is slowly dimmed up to a point where no further changes in brightness can be seen, and the maximum level set at this point. Enter into the switch Setup Mode - See PART A Click the push button 3 times LED will blink 3 times Note: If more than one dimmer is connected to the same load, all dimmers connected to this load will now blink 3 times Step 4 Press and hold the switch button to adjust to required maximum brightness level, releasing the button when the required level is reached Note: The direction of adjustment will alternate with each press Step 5 Click once to save & exit Note: If there are multiple LEDsmart + switches connected in parallel, the maximum brightness levels only needs to be set in one device. The setting is automatically saved to all other switches connected in parallel 4

5 C: Setting the Soft Start Feature The switch includes a soft start option. This soft start switches the lighting on over a half second period. This can increase lamp life in some cases and can also produce a better switch on effect for the user. By default, soft start is disabled. To enable soft start, follow the steps below. Enter into the switch Setup Mode - See PART A Click the push button 4 times LED will blink 4 times Note: If more than one dimmer is connected to the same load, all dimmers connected to this load will now blink 4 times Step 4 To enable the soft start feature Push and hold the push button until the lamps(s) turn ON To disable the soft start feature Push and hold the push button until the lamps(s) turn OFF (default) Step 5 Click once to save & exit Note: If there are multiple LEDsmart + switches connected in parallel, the maximum brightness levels only needs to be set in one device. The setting is automatically saved to all other switches connected in parallel 5

6 D: Setting Off State Indication When the switch is off, the white LED indicators in the switch can be set to glow or turn off. By Default, the white LED indicators are set to glow when the switch is turned off. To set the LED indicators to turn off when the switch is off, follow the steps below. Enter into the switch Setup Mode - See PART A Click the push button 5 times LED will blink 5 times Step 4 To set Indicator to glow on when switch is off Push the button until the lamp(s) turns ON (default) To set Indicator to turn off when switch is off Push the button until the lamp(s) turns OFF Step 5 Click once to save & exit 6

7 E: Setting Multimate Dimmer Mode Enter into the switch Setup Mode - See PART A Click the push button 8 times LED will blink 8 times a. If the MultiMate function is currently Disabled, lamp(s) connected to the dimmer will now turn OFF b. If the MultiMate function is currently Enabled, lamps(s) connected to the dimmer will now turn ON Step 4 To Enable MultiMate (Default) push-and-hold the button until the lamp(s) turns ON To Disable MultiMate push-and-hold the button until the lamp(s) turns OFF Step 5 Click once to save & exit 7

8 F: Resetting to Factory Default Enter into the switch Setup Mode - See PART A Click the push button 10 times The switch will automatically exit Setup Mode once reset 8

9 Copyright This installation guide is copyright to Gerard Lighting. Except as permitted under relevant law, no part of this user and installation guide may be reproduced by any process without written permission of and acknowledgement to Gerard Lighting. Gerard Lighting Pty Ltd (Gerard Lighting) reserves the right to alter the specifications, designs or other features of any items and to discontinue any items at any time without notice and without liability. While every effort is made to ensure that all information in this user and installation guide is correct, no warranty of accuracy is given and Gerard Lighting shall not be liable for any error. Printed on recycled paper Product of Gerard Lighting Pty Ltd ABN Gow Street Padstow NSW 2211 Contact General Enquiries: DALI (3254) or Technical Services: or Fax: Diginet is a brand of the Gerard Lighting Group Version: Issue 1 July 2016 DIGINET.NET.AU

Push Button Hour Timer Programmable between ¼ hour and 7½ hours with built in multi-way control

Setup Functions Guide MMTH/PB Push Button Hour Timer Programmable between ¼ hour and 7½ hours with built in multi-way control DIGINET.NET.AU Timer Setup Push Button Hour Timer The LEDsmart + push button