LED Display Method Each pattern of status is represented depending on the difference of the 4 lighting patterns of LED.

Size: px

Start display at page:

Download "LED Display Method Each pattern of status is represented depending on the difference of the 4 lighting patterns of LED."

Alvin Terence Parsons
5 years ago
Views:

1 .6 STATUS DISPLAS.6. Display ethod Each pattern of status is represented depending on the difference of the 4 lighting patterns of. ) Status This is normal operation status such as on-line or processing. ) Status This is warning status in which operation can continue. If a user continues the operation, an error might occur. This warns a user. ) Status Operation cannot continue. An operator has to implement an appropriate treatment and recover from the error. Fatal error means an irrecoverable error that requires a service call..6. display priority A user cannot continue using the printer. The user has to implement an appropriate measure against the error to recover from the error. Fatal errors are irrecoverable and require service call..6. types Name (Ready) onsumable olor POWER ON/ONLINE/OFFLINE/ save/data receiving, printing, Job (green) progress. (amber) (amber) (amber) Table A- types/functions canceling. Warming - up, density adjustment, temperature adjustment in out warning/alarm, manual feed request onsumables life warning/alarm, consumables installation error jam. over open error Function 0590TX Rev. 8 /

2 .6.4 ON patterns () GREEN Table A- (GREEN) types/functions Symbol 4 eans GREEN OFF T.B.D. GREEN ON GREEN Blinking (S cycle) GREEN Blinking (500mS cycle) GREEN Blinking (0ms cycle) GREEN Blinking 4 (4.5S ON, 500mS OFF) Statux POWER OFF ON patterns are determined by -level status. ONLINE (Idle) OFFLINE (This blinking pattern always takes place while error is occurring.) Data receiving, printing (including local print) Warming - up, density adjustment, temperature adjustment in progress Job canceling Saving () ABER Table A- (ABER) types/functions Symbol eans ABER OFF T.B.D. ABER ON ABER Blinking (S cycle) ABER Blinking (500mS cycle) ABER Blinking (0ms cycle) Statux ONLINE ON patterns are determined by -level status. is occurring (Printing possible) An error has happened, but printing can continue if a user presses ONLINE/ANEL key. An error has happened. A user needs to replace consumables or remove jammed paper and etc. And then, the printer recovers from the error and printing becomes possible. A serious error has happened. Rebooting or service call is required. 0590TX Rev. 8 /

3 .6.5 displays list Table A-4 displays list Priority onsumable EEPRO initializing. After the has gone out, the turns ON in the order of - - onsumable -. RA checking The controller side is initializing. EEPRO is initializing. 96 ON LINE status. 95 OFF LINE status. If is turned off, you cannot tell this status from POWER OFF. 9 Data receiving and processing has not yet started. Displayed mainly during PJL process without text print data or during job spooling. 9 Data receiving or output processing. 9 Un - printed data remains in buffer. Waiting for data to follow. 90 The printer is printing. 89 The printer is Demo printing. Not displayed when the printer prints Demo page added by a user. ( PRINTING appears.) 87 The printer is printing StatusPage. 84 ollate printing. Iii: The number of copy in printing. jjj: The total number of printing. When the total number of printing is, it is a normal printing display. 8 opy printing. kkk: The number of papers in printing. lll: The total number of printing. When the total number of printing is, it is a normal printing display. 8 Indicates that job cancellation has been instructed and data is being ignored until the job completion. 8 Indicates if JA occurs when Jam Recover is OFF, that job cancellation has been instructed and data is being ignored until the job completion. 8 Warming up. 80 Printing is paused due to high temperature of the drum. Or waiting for heat - measure when the narrow width paper is switched to wider width paper A printer is in power save mode. Displayed in a combination of other message in the first line. 78 Executing Auto olor isregistration Adjustment 0590TX Rev. 8 /

4 Priority onsumable 77 Executing Auto Toner reproduction curve compensation Executing Auto Density Adjustment. Toner amount is low. In case of LOW TONER=STOP in the menu, onsumable turns on and the printer shifts to OFF LINE. When ON LINE switch is pressed, printer shifts to ONLINE, and printing can continue until TONER EPT. This message also appears when waste toner becomes NEAR FULL. 7. If you open/close the cover or turn off the power and then turn on after Waste Toner Full error (priority 5.) once appeared, this warning appears. (Does not happen to Black.) Displayed in a combination of the other message on Line. While this message is being displayed, an waste toner full error happens at every 50 (approx.) sheets printing, and the printer stops OFF - LINE. 7 Invalid data was received. Press the ON LINE switch and eliminate the warning. Displayed when unsupported PDL command is received or a spool command is received without HDD. 70 Notifies the drum is near life (warning). Displayed in a combination of other message in the first line. 69 Notifies the fuser unit is near its life. (warning) 68 Notifies the belt unit is near its life. (warning) 67 A fuser unit life error occurred and a user opened/closed the cover or rebooted the power. After the printer prints 500 sheets, the error occurs again. 66 A belt unit life error occurred and a user opened/closed the cover or rebooted the power. After the printer prints 500 sheets, the error occurs again. 65 A toner empty error occurred and a user opened/closed the cover or rebooted the power. After the printer prints approx. 50 sheets (A4, 5% density), the error happens again. 64 A drum life error occurred and a user opened/closed the cover or rebooted the power. After the printer prints approx. 500 sheets, the error happens again. 0590TX Rev. 84 /

5 Priority onsumable 40 out in Tray/ or a tray is removed. Handled as a warning until printing is designated. PTRA EPT appears when paper is loaded from PTRA and Out is found. This warning disappears with cover open/close or power reboot when the job being printed is completed. P TRA TRA 6.5 OP data memory full. Only copy is printed instead of the copies designated. Recovers by pressing ONLINE key. anual feed print request. anual - feed the paper indicated in mm. Recovers by pressing ONLINE key. (500) Tray media type and print data media type mismatch. Load mmm/ppp paper in tttttt tray. Recovers by pressing ONLINE key. P TRA TRA Tray paper size or tray paper size & media type mismatch with that of print data. Load mmm/ppp paper in tttttt tray. Recovers by pressing ONLINE key. P TRA TRA Printing request was made to empty Tray/ or printing request was made to removed Tray. Or a printing request was made to removed Tray when Tray is not installed. Load paper and close the tray. Æ Recovers. Load mmm paper. TRA 49 8 The printer tried to load paper from PTRA, but could not detect the paper. Load mmm paper and press ONLINE key. Æ Printing starts. P TRA emory Overflow. If ON LINE switch is pressed, printing continues. Install expansion RA or decrease the data amount * Waste toner is full. Toner has to be replaced. (Does not happen to Black toner.) If cover is opened/closed, the printer becomes a warning status and the printer can print another 50 sheets (approx.) Appears to let a user to check if * toner was replaced at cover Open/lose after waste toner full error. (In case of waste toner full, toner replacement cannot be recognized from the device appearance.) (Happens to,,, and does not happen to.) When es is selected (ONLINE pressed for 5 seconds), toner counter is reset. When No is selected (ANEL pressed for 5 seconds), toner counter is not reset. The printer displays and can print another 50 sheets (approx.). 0590TX Rev. 85 /

6 Priority onsumable 4 * toner is empty. When a user opens/closes the cover, the printer becomes a warning status and can print another 50 sheets (A4 5% density). (The number of sheets: TBD) Something is wrong with the toner sensor. When the engine is set to Factory mode, this is a service call error (see below.) (This warning happens to PU/FW 00.8 and greater.) An inappropriate size paper was loaded from the tray. heck the paper in the tray and check if multiple feed happened. If a user opens/closes the cover, the printer performs recovery printing and printing continues. 400 JA has occurred. P TRA 90 0 JA has occurred. TRA FEED JA has occurred in paper path. Transport Exit Duplex Entry Printing Page Lost Drum life. When a user opens/closes the cover, the printer enters warning status, prints 500 sheets and the error happens again Fuser life. When a user opens/closes the cover, the printer enters warning status, prints 500 sheets and the error happens again. 54 Belt life. When a user opens/closes the cover, the printer enters warning status, prints 500 sheets and the error happens again. 55 Waste toner full. When a user opens/closes the cover, the printer enters warning status just once, prints 500 sheets and the error happens again. 56 Drum is not correctly set Belt is unlocked or black drum is not correctly set. 4 9 Belt unit is not correctly set. 0 8 Fuser unit is not correctly set TX Rev. 86 /

7 Priority onsumable The cover is open. TOP FRONT (The sensor cannot tell top cover from front cover. Thus, when one of them is open and when both are open, 0 and are displayed in toggle.) The cover is open. DUPLEX A network error is occurring. Rebooting in progress. d: Decimal value ( digit) and indicates a cause of the rebooting. d = 0: Reboot due to a cause other than the below. = :Reboot by a PJL command. = : Reboot due to menu change. = : Reboot due to quit operator of PostScript language. = 4: Reboot from Network utility (including Web). (See service call list.) Fatal (See service call list.) Fatal 0590TX Rev. 87 /

8 .6.6 Displaying of Service all odes With the 550, whenever service error occurs, each -, onsumable, and - rapidly blinks simultaneously at 0mS intervals. Every time the ONLINE SW and the ANEL switch are depressed simultaneously for 5 seconds or more in this state, the printer enters error code display mode. In this mode, each error code, a three-digit decimal number, represents bits (4 s times). After the error code display mode starts, displays the hundred's place of the error code. If the ONLINE SW is depressed once in this state, displays the ten's place of the error code. If the ONLINE SW is depressed twice in this state, displays the one's place of the error code. Immediately after the ONLINE switch is depressed (00mS), all the s go off so that a user can confirm that the switch was depressed even though the same code such as or continues. If the ONLINE SW is depressed three times, error code display mode ends, and the will go back to its rapid blinking state. If it is not depressed for more than 0 seconds, error code display mode ends as well. One example of display pattern at error occurrence is provided below. The is laid out in the order of Ready,, onsumable, and from the far left side, and what each symbol means is given in Table A-5-. Table A-5- ode 07 display pattern After error code display mode starts Hundred's place 0 Press ONLINE switch first time Ten's place 7 Press ONLINE switch second time One's place Table A-5- ode 86 display pattern After error code display mode starts Hundred's place Press ONLINE switch first time Ten's place 8 Press ONLINE switch second time One's place 6 Table A-5- Definition of symbols Symbol Difinition GREEN ON ABER ON GREEN / ABER OFF 0590TX Rev. 88 /

Understanding printer messages

Understanding printer messages The operator panel displays messages describing the current state of the printer and indicates possible printer problems you must resolve. This topic provides a list of all printer messages, explains what