Standard Accessories. Install software and driver. Introduction. Caution

Size: px

Start display at page:

Download "Standard Accessories. Install software and driver. Introduction. Caution"

Curtis Arnold
5 years ago
Views:

1 Standard Accessories LEAPER-3D FLASH WRITER main unit x1, USB cable x1, DC 12V/500mA adaptor x1, PC Software, drivers and manual on CD-ROM x1 Introduction Main unit Unit top view IC package diagram Adaptor Power switch USB cable Unit back view USB port (B type) Install software and driver 1. Set Font Size to [small fonts] (96 dpi) to have the optimal display. 1.1 Click the right button on the desktop. -> Select the [Properties] at the bottom of the function menu. 1.2 Select [Settings] and then click the [Advanced] to set Font Size. 2. Install the software before connecting the Leaper-3D to the PC. 2.1 Insert the software CD into your CD-ROM drive. Normally the installation program will start automatically (if Auto is enabled for your CD-drive). Follow the instructions to complete installation. 2.2 If Auto doesn't work, click [Setup.exe] in the CD directory to start the installation. 3. Install the driver for the Leaper-3D hardware. 3.1 Make sure the Leaper-3D power is [OFF]. Connect the power adapter to the Leaper-3D and a power outlet. 3.2 Connect the USB cable to PC and to the programmer USB port. 3.3 Turn the Leaper-3D power to [ON]. Windows will now start the [Found New Hardware Wizard]. 3.4 Install Hardware Device Driver -> Search for a suitable driver for my device (recommended) 3.5 Select Optional search locations -> CD-ROM drives 3.6 Driver Files Search Result -> Windows will find a driver for this device...\driver\flashwriter.inf 3.7 Click [Finish] in the Found New Hardware Wizard The Leaper-3D software and drivers have now been installed and the unit is ready for usage. Textool Textool handle DC 12V input socket Caution 1. It is preferred to use an internal USB port of your PC. External USB ports are not recommended because of shared bandwidth and possible compatibility issues of other USB devices. [3.3] [3.4] [3.5] LEAP Electronic Co., Ltd. Tel : Fax : http : // service@leap.com.tw [3.6] [3.7]

2 Operation window Source file editing Programming source Load from PC Read from source IC Verify source IC Edit file Exit program 8bits HEX display 16bits HEX display Buffer & file information IC manufacturer, type number Address of data Click and enter new address. Device verify CheckSum HEX code Display Click to enter hexadecimal data. Programming status ASCII code Display Click to enter text. Exit edit window Progress bar Erase Blank check Program Verify Program process & options Protect / security Stop Confirm changes Select IC number 8/16/32 Bits Cancel changes Load file Get data block checksum Data block - Move/Copy/Swap Data block - Fill selected IC size load file size maximum size of buffer

Standard Accessories LEAPER-3C Flash Writer main unit x1, USB cable x1, DC 12V/500mA adaptor x1, PC Software, drivers and manuals on CD-ROM x1 Introduction 16X2 LCD display IC package diagram Main

3 Standard Accessories LEAPER-3C Flash Writer main unit x1, USB cable x1, DC 12V/500mA adaptor x1, PC Software, drivers and manuals on CD-ROM x1 Introduction 16X2 LCD display IC package diagram Main unit Unit top view Adaptor Function keys USB cable Power switch Unit back view USB port (B type) DC 12V input socket Install software and driver 1. Set Font Size to [small fonts] (96 dpi) to have the optimal display. 1.1 Click the right button on the desktop. -> Select the [Properties] at the bottom of the function menu. 1.2 Select [Settings] and then click the [Advanced] to set Font Size. 2. Install the software before connecting the Leaper-3C to the PC. 2.1 Insert the software CD into your CD-ROM drive. Normally the installation program will start automatically (if Auto is enabled for your CD-drive). Follow the instructions to complete installation. 2.2 If Auto doesn't work, click [Setup.exe] in the CD directory to start the installation. 3. Install the driver for the Leaper-3C hardware. 3.1 Make sure the Leaper-3C power is [OFF]. Connect the power adapter to the Leaper-3C and a power outlet. 3.2 Connect the USB cable to PC USB port and to the programmer USB port. 3.3 Turn the Leaper-3C power to [ON]. Windows will now start the [Found New Hardware Wizard]. 3.4 Install Hardware Device Driver -> Search for a suitable driver for my device (recommended) 3.5 Select Optional search locations -> CD-ROM drives 3.6 Driver Files Search Result -> Windows will find a driver for this device...\driver\flashwriter.inf 3.7 Click [Finish] in the Found New Hardware Wizard The Leaper-3C software and drivers have now been installed and the unit is ready for usage. Master Textool Slave Textool Textool handle Attention Battery compartment 1. It is preferred to use an internal USB port of your PC. External USB ports are not recommended because of shared bandwidth and possible compatibility issues of other USB devices. 2. In PC mode operation, the Slave textool is used for all operations. In stand-alone mode, the source IC should be placed in the Master textool and the target IC in the Slave textool. [3.3] [3.4] [3.5] [3.6] LEAP Electronic Co., Ltd. Tel : Fax : http : // service@leap.com.tw [3.7]

4 Operation window Source file editing Programming source Load from PC Read from source IC Verify source IC Edit file Exit program 8bits HEX display 16bits HEX display Buffer & file information IC manufacturer, type number Address of data Click and enter new address. Device verify Check SUM HEX code Display Click to enter hexadecimal data. Programming status ASCII code Display Click to enter text. Exit edit window Progress bar Erase Blank check Program Verify Program process & options Protect / security Stop Confirm changes Cancel changes Select IC number Load file 8/16/32 Bits Get data block checksum Data block - Move/Copy/Swap Data block - Fill selected IC size load file size range by maximum size of buffer

Stand-Alone Operation Mode Main frame LCD Display IC number IC Checksum 29F010 E700 C+P+V 5.00V Programming Voltage Procedure Blank Check IC number 29F010 **** Checking > Status IC Checksum Keypad O.

5 Stand-Alone Operation Mode Main frame LCD Display IC number IC Checksum 29F010 E700 C+P+V 5.00V Programming Voltage Procedure Blank Check IC number 29F010 **** Checking > Status IC Checksum Keypad O.K. ERROR Function Descriptions Select IC Vendor Switch IC Number Blank Check to SLAVE Read Checksum of MASTER and verify with SLAVE Copy MASTER to SALVE 29F010 **** Checking PASS 29F010 **** Checking FAIL Select IC Vendor LCD Display Keypad Function Descriptions Select IC Vendor Select Vendor AMD IC brand Programming Procedure Select Prog. Procedure Prog. Procedure Select Prog. Procedure Switch IC Number Confirm IC brand LCD Display Keypad Function Descriptions Select Procedure C+P+V Flash - to select IC Vendor 27CXXX- to select Algorithm Switch Prog. Procedure Confirm Prog. Procedure Read & Verify Checksum IC number Previous IC Checksum 29F010 Verify > Status 29F010 Verify > 26AF 26AF Erase, Check, Program, Verify & Protect according to Prog. Procedure O.K. ERROR IC number Previous IC Checksum O.K. ERROR Read Checksum of MASTER 29F Verify PASS Read Checksum of MASTER 29F010 12EF Verify FAIL 29F010 1A36 PASS 29F Verify FAIL Wrong procedure Programming Algorithm LCD Display Keypad Function Descriptions Select Prog. Algorithm Select Algorithm Q-100uS Prog. Algorithm ** Only 27Cxxx ** Programming Voltage Select Prog. Voltage Prog. Voltage Select Prog. Algorithm Switch Prog. Algorithm Confirm Prog. Algorithm LCD Display Keypad Function Descriptions Select Voltage 12.70V ** Only 27Cxxx ** Select IC Vendor Switch Prog. Voltage Confirm Prog. Voltage

Standard Accessories Leaper-48 main unit x1, USB cable x1, DC 12V/2A adaptor x1, Operation software CD-ROM x1, Quick User Guide x1 Introduction 48Pin Textool Main unit Adaptor USB cable Unit top view

-> Select the [Properties] in the bottom of the function menu. 1.2 Select [Settings] and then click the [Advanced] to set Font Size. 2. Install the software before connecting the Leaper-48 to the PC.

exe] in the CD directory to install. 3. Install the driver of Leaper-48 hardware. 3.1 Make sure the Leaper-48 power is [OFF]. Connect the power adaptor to the Leaper-48.

6 Standard Accessories Leaper-48 main unit x1, USB cable x1, DC 12V/2A adaptor x1, Operation software CD-ROM x1, Quick User Guide x1 Introduction 48Pin Textool Main unit Adaptor USB cable Unit top view Power led Action led Power switch Unit back view USB port (B type) Install software and driver 1. Set Font Size to [small fonts] (96 dpi) to have the optimal display. 1.1 Click the right button on the desktop. -> Select the [Properties] in the bottom of the function menu. 1.2 Select [Settings] and then click the [Advanced] to set Font Size. 2. Install the software before connecting the Leaper-48 to the PC. 2.1 Insert the software CD into your CD-ROM drive. Auto start-up installation. Follow the instructions to complete installation. 2.2 If Auto doesn't work, click [Setup.exe] in the CD directory to install. 3. Install the driver of Leaper-48 hardware. 3.1 Make sure the Leaper-48 power is [OFF]. Connect the power adaptor to the Leaper-48. Plug in and then turn on the power. The green led on the adaptor and power led on the programmer panel will be lit on. 3.2 Link the USB cable to PC USB port and programmer USB port. 3.3 After assembling the USB cable and the power adaptor, Windows will auto start-up [Found New Hardware Wizard]. 3.4 Install Hardware Device Driver -> Search for a suitable driver for my device(recommended) 3.5 Locate driver files Optional search locations -> CD-ROM driver 3.6 Driver Files Search Result -> Windows found a driver for this device...\driver\usbwriter.inf 3.7 Completing the Found New Hardware Wizard Textool handle IC package diagram DC 12V input socket Attention 1. It is preferred to use an internal USB port of your PC. External USB ports are not recommended because of shared bandwidth and possible compatibility issues of other USB devices. 2. When you use special socket adapters (PLCC, TSOP, SOP...), Please pull the textool up to 80. Put the special socket adapter in the textool and then pull the handle down to fix the socket adapter. [3.3] [3.4] [3.5] LEAP Electronic Co., Ltd. Tel : Fax : http :// service@leap.com.tw [3.6] [3.7] * Above installation is described in Windows 2000 *

.. ) Device DC/AC parameter settings Device

turned on and connected to the PC Programming

Programmer information *only enabled when

2. Sound settings Programmer self-test *only

source IC Verify source IC Edit file Exit

manufacturer, type number and package Device

Process option Counter Programming status

7 Parameters Options 1.Memory device split function 2.High-low voltage verify 3.Pre-check on device ( i.e. pin scan, IC identify... ) Device DC/AC parameter settings Device settings *only enabled when programmer is turned on and connected to the PC Programming source 1.Programmer information *only enabled when programmer is turned on and connected to the PC 2. Sound settings Programmer self-test *only enabled when programmer is turned on and connected to the PC *Remove any device from the ZIF socket, if present. Select IC number IC type Load from PC Read from source IC Verify source IC Edit file Exit program Source filename Load file IC manufacturer, type number and package Device verify Check SUM Device pin check Signal light Process option Counter Programming status Re-scan Ignore signal Clear counter Progress percentage Erase Blank check Program Verify Program process & options Protect / security Stop Auto loop Cancel Instruction

Source file editing 8bits HEX display 16bits HEX display Buffer & file information Project Description of

Protect lock: Undeletable Address of data Click and enter new address.

Select project Double click to run the project. Single click to select the project.

Delete project Create new project Create new project with present settings. Only reserve for 10 records.

Execute Project Exit edit window Hot Key Confirm changes Cancel changes Get data block checksum *When a

8 Source file editing 8bits HEX display 16bits HEX display Buffer & file information Project Description of Project IC number, manufacturer & package Auto : Once: Single program Multi: Loop program NO: Manual program Protect lock: Undeletable Address of data Click and enter new address. HEX code Display Click to enter hexadecimal data. ASCII code Display Click to enter text. Select project Double click to run the project. Single click to select the project. Click right button to display properties of the project. Double click blank row to create a new project. Delete project Create new project Create new project with present settings. Only reserve for 10 records. Or the project keeper will delete the un-protect and former file (on the top row). Execute Project Exit edit window Hot Key Confirm changes Cancel changes Get data block checksum *When a Microchip PIC device is selected, IC checksum will be shown directly. Data block - Move/Copy/Swap Data block - Fill selected IC size load file size range by maximum size of buffer Click [Space] bar in the main operation screen to pop Hot Key menu.

How to create a project Step 1 Create a Project 1.Click [Project] icon. 2.Click [Create] button to start up the project editing window./ Double click blank column to create a new project. 3.

Step 1 How to program an IC Select IC number 1.Click [Type] icon. 2.Select IC manufacturer. 3.Select IC number. 4.Click [OK] Button. Step 2 Get source data Mode 1: Load from file 1.Click [Load] icon.

9 How to create a project Step 1 Create a Project 1.Click [Project] icon. 2.Click [Create] button to start up the project editing window./ Double click blank column to create a new project. 3.Enter project description. 4.Select [Auto loop] parameter: Once/ Batch/Manual. 5.Select [Project Protect] to protect project. 6.Click [OK] to save the project or click [Cancel] to discard any changes. Step 1 How to program an IC Select IC number 1.Click [Type] icon. 2.Select IC manufacturer. 3.Select IC number. 4.Click [OK] Button. Step 2 Get source data Mode 1: Load from file 1.Click [Load] icon. 2.Click [Browse] to load file. 3.Set file format. 4.Click [Load] button to read data. Mode 2: Read from source IC 1.Place source IC. 2.Click [ Read] icon. >Start to read and verify IC. 3.Check status and checksum Step 1 Execute Project 1.Click [Project] icon. 2.Dubble click to run project or click right button to check the properties of the project. Double click blank column to create a new project. Step 2 Program IC Description of Project IC number, manufacturer & package Auto : Single program Step 3 Program IC Mode 1:Program single IC 1.Select process options. 2.Place target IC. 3.Click [] icon. >Process IC with selected options. 4.Check process status. Process option Method1: One time auto-program 1.Place target IC. >Process IC with project options. 2.Check process status. Method 2: Loop auto-program 1.Place target IC. >Process IC with project options. 2.Check process status. 3.Repeat above steps for the next IC. 4.Click [Cancel] botton to stop programming. Place target IC Project created date and time Auto : Loop program Programming Process E: Erase IC, C: Blank check, P: Program IC, V: Verify IC, S: Protect/Security Protect lock: Undeletable Mode 2: Program batch of ICs 1.Select process option. 2.Place target IC. 3.Click [Auto Loop] icon. >Process IC with selected options. Auto Loop 4.Check process status. >Waiting for placement of the next target IC. 5.Repeat above steps for the next IC. 6.Click [Cancel] icon on Scan IC Window to stop process. Place target IC Replace target IC Check IC location and pin status Click to ignore the IC check and process the next IC Click to stop the batch programming Place Target IC Replace target IC Method 3: Manual program 1.Place target IC 2.Click [] icon. >Process IC with project options. 3.Check process status. Check IC pins and location Click to ignore the IC check and process the next IC Click to stop the batchprogram

Dataman-S6 - User's Manual. Dataman-S6 Compact USB Programmer User's Manual

Dataman-S6 - User's Manual. Dataman-S6 Compact USB Programmer User's Manual Dataman-S6 Compact USB Programmer User's Manual Contents Chapter 1 Product Description 1-1 Introduction 1-2 Safety Information 1-3 Precautions 1-4 Operating System, Hardware Requirements 1-5 Accessories