Panel. Chapter 16. Solar Car. A. Sketch. Step 1. Click File Menu > New, click Part and OK. B. Save as "PANEL". Step 1. Click File Menu > Save As.
|
|
- Jordan Williams
- 5 years ago
- Views:
Transcription
1 Chapter 16 Solar Car Panel A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Center Rectangle (S) in the Rectangle flyout on the Sketch toolbar. Fig. 1 Step 4. Draw a center rectangle starting at the Origin, Fig. 2. Step 7. Click Smart Dimension (S) on the Sketch toolbar. Origin Step 8. Dimension rectangle 10.5 by 5, Fig. 2. Step 9. Click Zoom to Fit Step 10. Click Features (F) on the View toolbar. on the Command Manager toolbar. Step 11. Click Extruded Boss/Base Step 12. In the Property Manager set: Depth.04 click OK, Fig. 3 and Fig. 4. B. Save as "PANEL". Step 1. Click File Menu > Save As. on the Features toolbar. Fig. 2 Step 2. Key-in PANEL for the filename and press ENTER. Fig. 3 Fig. 4 SolidWorks 12 PANEL SOLAR CAR Page 16-1 Cudacountry.net Tech Ed cudacountry@hotmail.com 8/21/12
2 C. Appearance. Step 1. Click the Panel to select the part, click Appearances Callout on the Content menu and click PANEL, Fig. 5. Click part Step 2. In the Appearances Property Manager, under Color click second yellow swatch, Fig. 6 click OK, Fig. 7. Fig. 5 Step 3. Save. Use Ctrl-S. D. Enable PhotoView 360. Step 1. If necessary, turn on PhotoView 360. Click Tools Menu > Add-Ins. Click to place a check in PhotoView 360 check boxes under Active Add-ins and under Start Up and click OK, Fig. 8. E. Solar Panel Decal. Step 1. Click Top on the Standard Views toolbar. (Ctrl-5) Fig. 7 Fig. 6 Step 2. Click PhotoView 360 Menu > Edit Decal. Step 3. In the Decals Property Manager Image tab: under Decal Preview click Browse and My Documents button open solarpanel1.jpg, Fig. 9. Fig. 8 Fig. 9 SolidWorks 12 PANEL SOLAR CAR Page 16-2
3 Step 4. Click the Mapping tab at the top of the Decals Manager, Fig. 10 under Selected Geometry unselect all but Select Faces click the top face of the Panel, Fig. 11 under Mapping set Projection Direction Current View click Update to Current View button grab the corner handles and size the image to fit Panel, Fig. 12 click OK. Step 5. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 6. Save. Use Ctrl-S. Top face Fig. 11 Fig. 12 F. Insert into Assembly. Step 1. Open your SOLAR CAR ASSEMBLY file. Fig. 10 Step 2. Click Insert Components on the Assembly toolbar. Step 3. Click Browse in the Property Manager. Step 4. Select Panel file and click Open. Step 5. Place Panel as positioned in Fig. 13. Click OK in the Property Manager. G. Mate: Axle and Arm and Cross Support. Fig. 13 Step 1. Click Filter Faces (X) on the Selection Filter toolbar at the bottom of the display, Fig. 14. If necessary, use F5 key to display the toolbar. Step 2. Click Mate on the Assembly toolbar. Fig. 14 SolidWorks 12 PANEL SOLAR CAR Page 16-3
4 Step 3. Click top face Cross Support, Fig. 15. Step 4. Rotate view to view bottom face of Panel as shown in Fig. 16. To rotate, hold down middle mouse button (wheel) and drag. Step 5. Click bottom face of Panel, Fig. 16. Step 6. Click Add/Finish Mate Coincident mate. to add a Step 7. Rotate view to view rear face of Panel, Fig. 17. To rotate, hold down middle mouse button (wheel) and drag. Fig. 15 Step 8. Click rear face of the Panel and rear face of Cross Support, Fig. 17. Fig. 16 Step 9. Click Distance in Mate pop-up, Fig. 18. Set distance 1 and press EN- TER. The Panel should extent out 1 from the rear of Cross Support, Fig. 19. If positioned in opposite direction, click Flip Dimension in the Mate pop-up, Fig. 18. Click Add/Finish Mate to add Distance mate. Fig. 17 Fig. 18 Fig. 19 SolidWorks 12 PANEL SOLAR CAR Page 16-4
5 Step 10. Click Front on the View toolbar. (Ctrl-1) Step 11. Expand the Design Tree (click +) in the top left corner of the graphics area, Fig. 20. Step 12. Expand Cross Support and click Right Plane, Fig. 20. Step 13. Expand Panel and click Right Plane, Fig. 20 and Fig. 21. Step 14. Click Add/Finish Mate to add a Coincident mate. Step 15. Click OK in the Property Manager. Step 16. Turn off Filter Faces. Click Filter Faces (X) on the Selection Filter toolbar at the bottom of the display, Fig. 22. Step 17. Save. Use Ctrl-S. Fig. 21 Fig. 20 Fig. 22 SolidWorks 12 PANEL SOLAR CAR Page 16-5
F-1 Car. Blank. in the Feature Manager and click Sketch from the Content toolbar, Fig. 3. Origin. on the Features toolbar.
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. F-1 Car Blank Step 2. Click Part Metric from the list of templates and click OK, Fig. 1. If you are not using SOLIDWORKS templates (you should
More informationSolar Car. Chassis. in the Feature Manager and click Sketch from the Content toolbar, Fig. 2. Origin. on the Command Manager toolbar. Fig.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Solar Car Chassis Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Chassis. Step 1. Click Right Plane in the Feature Manager and click
More informationBody. Chapter 1. Simple Machines. A. New Part. Step 1. Click File Menu > New.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Simple Machines Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature
More informationTail Hook. Chapter 14. Airplane. A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK.
Chapter 14 Airplane Tail Hook A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right (plane) in the Feature Manager and click Sketch from the Content toolbar,
More informationWheels and Axle. Chapter 7. Simples Machines. A. Save As. Step 1. If necessary, open your Track Assembly 15 file. B. Insert Truck Assembly.
Chapter 7 Simples Machines Wheels and Axle A. Save As. Step 1. If necessary, open your Track Assembly 15 file. Step 2. Click File Menu > Save As. Step 3. Key-in WHEELS AND AXLE ASSEMBLY for the filename
More informationBlank. Chapter 1. CO2 Rail Car. A. New Metric Part. Step 1. Click File Menu > New. B. Body. Step 1. Click Right Plane
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. CO2 Rail Car Blank Step 2. Click Part Metric from the list and click OK, Fig. 1. If you are not using SolidWorks templates (you should be),
More informationSimple Machines. Body. Step 4. Start at Origin and sketch the 8 lines, Fig. 2. Fig. 1. Origin
Chapter 1 Simple Machines Body A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1. Step 3. Click
More informationCO2 Car Assembly. in the Property Manager to place the part at the origin, Fig. 1. on the Assemblies toolbar. SolidWorks Assembly CO2 CAR Page 8-1
Chapter 8 CO2 Car Assembly A. Insert Axles and Wheels. Step 1. Click File Menu > New, click Assembly Metric and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the
More informationAssembly Motion Study
Penny Hockey Chapter 10 Assembly Motion Study A. Rename Penny Mate. Step 1. Open your PENNY HOCKEY ASSEMBLY file. Step 2. Expand Mates in the Feature Manager and select the last Mate, Fig. 1. This should
More informationBoat. Battery Holder AA
Chapter 9 Boat Battery Holder AA A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch context toolbar, Fig. 1. Step 3. Click
More informationTerminal. Chapter 16. E-Car. A. Component from Design Library. SOLIDWORKS 17 Terminal E-CAR Page 16-1
Chapter 16 E-Car Terminal A. Component from Design Library. Step 1. Click the Design Library tab in the Task Pane (right side of graphics area), Fig. 1. Step 2. Expand routing and click electrical folder
More informationSimple Machines. Wheel. in the Feature Manager and click Sketch. on the Command Manager toolbar.
Chapter 3 Simple Machines Wheel A. Wheel. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step 3. Click
More informationAirplane Assembly. SolidWorks 10 ASSEMBLY AIRPLANE Page 9-1
Chapter 9 A. Insert Parts. Airplane Assembly Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the Property Manager,
More informationSpeedway. Body. (S) on the Sketch toolbar. Fig. 1
Chapter 1 A. New Part. Step 1. Click File Menu > New. Speedway Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature Manager
More informationChair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane.
Chapter 7 A. 3D Sketch. Step 1. If necessary, open your CHAIR file. Chair Top Rail Step 2. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 3. Zoom in around top of back leg, Fig. 1. To zoom,
More informationF1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the
Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.
More informationPhotoView 360 Decals
Chapter 10 Glider PhotoView 360 Decals A. Enable PhotoView 360. Step 1. If necessary, open your GLIDER ASSEMBLY file. Step 2. If necessary, turn on PhotoView 360. Click Tools Menu > Add- Ins. Click to
More informationWheel GT-F. Chapter 5. CO2 Shell Car. A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK.
Chapter 5 CO2 Shell Car Wheel GT-F A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1.
More informationDelta IV Heavy. Interstage. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Command Man- on the Features
Chapter 4 Delta IV Heavy Interstage A. Sketch Circles. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationGlider. Clay. Fig. 1 Side face. Step 5. In the Convert Entities Property Manager: click side face, Fig. 3 click OK twice, Fig. 3. Fig. 3.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. Step 2. Click the side face of the Fuselage,
More informationBattery Holder 2 x AA
Chapter 22 JSS Battery Holder 2 x AA A. Front Extrude. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Context toolbar,
More informationCO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar.
CO 2 Shell Car Chapter 2 Body A. Save as "BODY". Step 1. If necessary, open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY for the filename and press ENTER. B. FRONT Wheel Shell.
More informationSpring Assembly. in the Begin Assembly Property. on the Standard toolbar and click Add-Ins.
Chapter 2 Spring Assembly A. Create New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Cancel Manager. in the Begin Assembly Property B. Enable Toolbox Browser. Step 1. If
More informationBoat. Hull. Step 4. Sketch point directly above the Origin, Fig. 2. Use the inferencing line, the dotted line that appears when you sketch the point.
Chapter 1 Boat Hull A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step 3. Click Point on
More informationClay. Chapter 9. Glider. A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. C. Sketch. Step 1. Click the side face of the
More informationBody. Chapter 2. CO2 Rail Car E. A. Save as "BODY RAIL E". Step 1. Open your BLANK file.
Chapter 2 A. Save as "BODY RAIL E". Step 1. Open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY RAIL E for the filename and press ENTER. CO2 Rail Car E Body B. Appearance. Step
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.
More informationPropeller. Chapter 13. Airplane. A. Base for Blade. Step 1. Click File Menu > New, click Part and OK.
Chapter 13 Airplane Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch toolbar, Fig. 1. from the Content Step
More informationDelta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar.
Chapter 6 Delta Dart Socket A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step
More informationSkateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2
Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationJSS. Ping Pong Ball. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Sketch toolbar.
Chapter 18 JSS Ping Pong Ball A. Half Circle Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig.
More informationFuselage and Sharks Tooth
Chapter 4 Glider Fuselage and Sharks Tooth A. Save as "FUSELAGE". Step 1. Open your FUSELAGE BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in FUSELAGE for the filename and press ENTER. B.
More informationCO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig.
Chapter 17 CO2 Shell Car Axle Retainer A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationFig. 1. Fig. 1. on the Standard Views toolbar. SolidWorks ASSEMBLY AIRPLANE Page 8-1
Chapter 8 Airplane Assembly A. Insert Set of Parts. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click View Menu > Origins to display the origin. Step 3. Click Keep Visible in the Property
More informationRocket 1. Fin. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig. 1. Fig. 2
Chapter 2 Rocket 1 Fin A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Line
More informationDelta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.
Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationH Stab and V Stab. Chapter 6. Glider. A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file.
Chapter 6 Glider H Stab and V Stab A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in H STAB for the filename and press ENTER. B. Sketch
More informationBottle Rocket. Drawing. on the Com- on the View Layout
Chapter 6 Bottle Rocket Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing Metric and OK. on the Com- Step 2. Click View Layout mand Manager toolbar. Step 3. Click Model View toolbar.
More informationSkateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line
Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step
More informationNose Cone. Chapter 4. Rocket 3D Print. A. Revolve. Step 1. Click File Menu > New, click Part and OK. SOLIDWORKS 16 Nose Cone ROCKET 3D PRINT Page 4-1
Chapter 4 Rocket 3D Print Nose Cone A. Revolve. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step
More informationDrawing. Chapter 10. Airplane. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager.
More informationBattery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
More informationChapter 11 Solar Car Drawing
Chapter 11 Solar Car Drawing A. Insert Top and Side Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Browse Step 3. Select your solar car assembly file and click Open. Step 4.
More informationAirplane Drawing. Chapter 10. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse Step 4. Select your AIRPLANE
More informationCO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.
Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step
More informationFlow Sim. Chapter 12. F1 Car. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 12 F1 Car Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar and
More informationSpeedway. Motion Study. on the Standard toolbar and click Add-Ins. at the lower
Chapter 8 Speedway Motion Study A. Enable SOLIDWORKS Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, enable Motion, click the flyout of Options on the Standard toolbar
More informationSpeedway. Motion Study. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click Tools Menu > Add-Ins.
Chapter 8 Speedway Motion Study A. Enable SolidWorks Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click
More informationMastercam X9 for SOLIDWORKS
Chapter 21 CO2 Shell Car Mastercam X9 for SOLIDWORKS A. Enable Mastercam for SOLIDWORKS. Step 1. If necessary, turn on Mastercam for SOLIDWORKS, click the flyout of Options on the Standard toolbar and
More informationGlider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar.
Chapter 5 Glider Wing 4 Panel Tip A. Open and Save As "WING 4 PANEL". Step 1. Open your WING BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in WING 4 PANEL for the filename and press ENTER.
More informationBoat Hull Solid. (Alt-2). in ribbon bar to fix and close ribbon Fig. 3 Mastercam X7 BOAT HULL SOLID Page 29-1
Mastercam X7 Chapter 29 A. Open Boat Block File. Step 1. Open your BOAT BLOCK file. Boat Hull Solid B. Save As BOAT HULL SOLID Step 1. Click File Menu > Save As. Step 2. Key-in BOAT HULL SOLID for the
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 21 CO2 Shell Car Mastercam X6 for SolidWorks Toolpaths A. Enable Mastercam for SolidWorks. Step 1. If necessary, turn on Mastercam for SolidWorks, click Tools Menu > Add-Ins. Step 2. In the dialog
More informationIntroduction to SolidWorks for Technology. No1: Childs Toy
Introduction to SolidWorks for Technology No1: Childs Toy Table of Contents Table of Contents... 1 Introduction... 2 Part Modelling: Cab... 3 Part Modelling: Base... 6 Part Modelling: Wheel... 12 Assembly:
More informationDrawing. Chapter 12. Beam. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View. on the View Layout toolbar.
Chapter 12 Beam Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationFlow Sim. Chapter 16. Airplane. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 Airplane Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar
More informationPenny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam Step 1. If necessary, save your BASE file in SOLIDWORKS.
Mastercam 2017 Chapter 22 Chapter 7 Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam 2017. Step 1. If necessary, save your BASE file in SOLIDWORKS. Step 2. In Mastercam 2017, click
More informationSOLIDWORKS: Lesson 1 - Basics and Modeling. UCF Engineering
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals UCF Engineering SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment for
More informationDrawing. Chapter 11. Bridge. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. on the View Layout toolbar.
Chapter 11 Bridge Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationBottom Truss ANALYSIS
Chapter 3 Beam Bottom Truss ANALYSIS A. Enable SolidWorks Simulation. Step 1. If necessary, open your Beam1 part file. Step 2. If necessary, turn on SolidWorks Simulation. To turn on Solid- Works Simulation,
More informationFlow Sim. Chapter 14 P-51. A. Set Up. B. Create Flow Simulation Project. Step 1. Click Flow Simulation. SolidWorks 10 Flow Sim P-51 Page 14-1
Chapter 14 A. Set Up. P-51 Flow Sim Step 1. If necessary, open your ASSEMBLY file. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in the
More informationFlow Sim. Chapter 16. Airplane. A. Add-In. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 A. Add-In. Step 1. If necessary, open your ASSEMBLY file. Airplane Flow Sim Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in
More informationBelt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 35 Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click Rectangle.
More informationMemo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet.
Commands Used New Part This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Click File, New on the standard toolbar. Select Part from the New SolidWorks
More informationSolidWorks 2015 User Interface
SolidWorks 2015 User Interface SolidWorks a Dassault Systèmes Product Starting SolidWorks 1) On the desktop, double-click or from the start menu select: All Programs SOLIDWORKS 2015 SOLIDWORKS 2015. 2)
More informationIntroduction to SolidWorks Basics Materials Tech. Wood
Introduction to SolidWorks Basics Materials Tech. Wood Table of Contents Table of Contents... 1 Book End... 2 Introduction... 2 Learning Intentions... 2 Modelling the Base... 3 Modelling the Front... 10
More informationSOLIDWORKS: Lesson 1 - Basics and Modeling. Introduction to Robotics
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals Introduction to Robotics SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment
More informationME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.
PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step
More informationSolidWorks 2009 & DCG Student Assignment
SolidWorks 2009 & DCG Student Assignment RD10 DCG Design & Communication Graphics 1 SolidWorks 2009 & DCG Student Assignment Table of Contents Focus of the lesson. 3 Getting Started Modelling the TV Plate
More informationCudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1
Mastercam 2017 Chapter 19 Cudacountry Radial A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New QAT. (Ctrl-N) on the Quick Access Toolbar Step 2. On the Wireframe tab click
More informationAirplane. Chapter 21. Mastercam A. Create Rectangle. B. Save As AIRPLANE. C. Set Grid and Snap.2. Mastercam 2017 Airplane Page 21-1
Mastercam 2017 Chapter 21 A. Create Rectangle. Airplane Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step 2. On the Wireframe tab click Rectangle.
More informationExport DXF to Illustrator
Chapter 12 Glider Export DXF to Illustrator A. Export Fuselage/Tooth Sketch as DXF". Step 1. Open your FUSELAGE part file. Step 2. Roll the rollback bar to below the Cut-Extrude1. To rollback, click Fillet1
More informationAutodesk Inventor - Basics Tutorial Exercise 1
Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be
More informationSOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering
SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now
More informationChapter 3. CO2 Car SolidWorks to Mastercam. A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks.
Chapter 3 CO2 Car SolidWorks to Mastercam X 2007 A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box scroll
More informationJewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3
Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in
More informationChapter 39. Mastercam Jewelry Box Tray. A. Sketch Tray Circle. B. Twin Edge Point Circles. Mastercam 2017 Tray Jewelry Box Page 39-1
Mastercam 2017 Chapter 39 A. Sketch Tray Circle. Jewelry Box Tray Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click
More informationTUTORIAL 2. OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs.
TUTORIAL 2 OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs. GETTING STARTED: 1. Open the SolidWorks program. 2. Open a new part file.
More informationChapter 36. Mastercam Jewelry Box Fixture. A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 36 Jewelry Box Fixture A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe
More informationCatamaran A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N).
Mastercam 07 Chapter 6 Catamaran A. Create Rectangle. Step. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step. On the Wireframe tab click Rectangle. Step
More informationThe Fundamentals of SolidWorks Featuring the VEXplorer robot with over 40 integrated stand-alone tutorials
INSIDE: Tutorial Model Files On CD The Fundamentals of SolidWorks 2007 Featuring the VEXplorer robot with over 40 integrated stand-alone tutorials David C. Planchard & Marie P. Planchard, CSWP SDC PUBLICATIONS
More informationFig. 2 Mastercam 2020 Spinning Top SW 19 to MCam20 TOOLPATHS Page 13-1
Mastercam 2020 Chapter 13 Spinning Top SOLIDWORKS 19 to Mastercam 2020 A. Open File in Mastercam 2020. Step 1. If necessary, save your Handle and Flywheel parts file in SOLIDWORKS. Step 2. In Mastercam
More informationChanges from SolidWorks 2003 to SolidWorks 2004
Changes from SolidWorks 2003 to SolidWorks 2004 The changes from SolidWorks 2003 to SolidWorks 2004 are primarily cosmetic. Consequently, it is quite easy to use the current edition of Learning SolidWorks
More informationEngineering. Statics Labs SDC. with SOLIDWORKS Motion Includes. Huei-Huang Lee. Better Textbooks. Lower Prices.
Engineering Includes Video demonstrations of the exercises in the book Statics Labs with SOLIDWORKS Motion 2015 Huei-Huang Lee Multimedia Disc SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com
More informationwith Video Instruction
SOLIDWORKS 2017 Tutorial with Video Instruction A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard, CSWP, SOLIDWORKS Accredited Educator SDC PUBLICATIONS Better Textbooks.
More informationSolidWorks 2008 Tutorial. with MultiMedia CD. A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling
INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects with MultiMedia CD A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard
More informationExport DXF to CorelDRAW
Chapter 13 Glider Export DXF to CorelDRAW A. Export Fuselage/Tooth Sketch as DXF". Step 1. Open your FUSELAGE part file. Step 2. Roll the rollback bar to below the Cut-Extrude1. To rollback, click Fillet1
More informationProject 3. Top Down Design In Context. Below are the desired outcomes and usage competencies based upon the completion of this Project.
Assembly Modeling with SolidWorks Project 3 Below are the desired outcomes and usage competencies based upon the completion of this Project. Project Desired Outcomes: 2AXIS-TRANSFER Assembly. PLATE-B Part.
More informationSolid Modeling SolidWorks Layout. ENGR 1182 SolidWorks 01
Solid Modeling SolidWorks Layout ENGR 1182 SolidWorks 01 Solid Modeling In The Real World Mechanical and Aerospace engineers need solid models of jet engine components and assemblies to do analysis on
More informationFigure 1: The excel document used to personalize a race car by changing the values of 5 parameters
How to Make a Personalized Race Car 1. Open the excel document entitled Parametric Flexitop Car Parameters.xlsx. 2. The excel document should be on the Sliders tab as seen in Figure 1. If not, click on
More informationTechnique or Feature Where Introduced
Part 6: Keypad 4 Mirrored features Patterned features First extrusion Rounded corners In the earpiece part, you defined a radial pattern, one that created new instances of a feature at intervals around
More informationLesson 4: Assembly Basics
4 Lesson 4: Assembly Basics Goals of This Lesson Understand how parts and assemblies are related. Create and modify the part Tutor2 and create the Tutor assembly. Tutor1 Tutor2 Tutor assembly Before Beginning
More informationSolidWorks Implementation Guides. User Interface
SolidWorks Implementation Guides User Interface Since most 2D CAD and SolidWorks are applications in the Microsoft Windows environment, tool buttons, toolbars, and the general appearance of the windows
More informationCHANNEL BLOCK SOLID. Step 7. For the Placement Point, click the bottom left gray rectangle and click OK. to fit drawing on the screen.
Chapter 9 CHANNEL BLOCK SOLID A. Create Rectangle. Step 1. Change to the Front View. Use green Front View or ALT-6 F. Hold down ALT and press 6. Key-in F. Step 3. Create. Step 4. Rectangle. Step 5. 1 Point.
More informationSolidWorks 2½D Parts
SolidWorks 2½D Parts IDeATe Laser Micro Part 1b Dave Touretzky and Susan Finger 1. Create a new part In this lab, you ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select
More informationParametric Modeling Design and Modeling 2011 Project Lead The Way, Inc.
Parametric Modeling Design and Modeling 2011 Project Lead The Way, Inc. 3D Modeling Steps - Sketch Step 1 Sketch Geometry Sketch Geometry Line Sketch Tool 3D Modeling Steps - Constrain Step 1 Sketch Geometry
More informationSolidWorks 2001 Getting Started
SolidWorks 2001 Getting Started 1995-2001, SolidWorks Corporation 300 Baker Avenue Concord, Massachusetts 01742 USA All Rights Reserved. U.S. Patent 5,815,154 SolidWorks Corporation is a Dassault Systemes
More informationInventor 201. Work Planes, Features & Constraints: Advanced part features and constraints
Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the
More informationAutodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Tim Varner - 2004 The Inventor User Interface Command Panel Lists the commands that are currently
More informationSolidWorks Intro Part 1b
SolidWorks Intro Part 1b Dave Touretzky and Susan Finger 1. Create a new part We ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select File New Templates IPSpart If the SolidWorks
More informationSOLIDWORKS 2018 Tutorial
SOLIDWORKS 2018 Tutorial with Video Instruction A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard, CSWP, SOLIDWORKS Accredited Educator SDC P U B L I C AT I O N S Better
More information