Quick Start Guide. AR530&AR550 Series Industrial Switching Routers. Issue: 07 ( ) Part number: HUAWEI TECHNOLOGIES CO.

Transcription

1 Quick Start Guide AR0&AR0 Series Industrial Switching Routers Issue: 0 (0--0) Part number: 0 HUAWEI TECHNOLOGIES CO., LTD

2 Packing List AR0 series industrial switching router (with the product model on the nameplate) Installation accessory package: - -pin AC input connector - Mounting bracket - Mx0 screws - Console cable - Warranty card - Mx0 screws - Quick Start Guide - USB extension cable - Hex bolts - 8-pin input connector - Cable outlet panel - Lock nuts - Stainless steel sheet - Ground cable - Plastic caps AR0 series industrial switching router (with the product model on the nameplate) Installation accessory package: - Ground cable - Warranty card - Console cable - Two -pin input connectors - Quick Start Guide - -pin connector Items and quantities in the installation accessory package vary depending on the product model. Safety Guidelines To ensure personal and equipment safety, observe all the safety precautions on the equipment and in this document. WARNING and CAUTION items do not cover all the safety precautions and are only supplementary to the safety precautions. Follow all the safety precautions and instructions provided by Huawei. The safety precautions outlined in this document are only those that Huawei can predict. Huawei is not liable for any consequence that results from violation of regulations pertaining to safe operations or safety codes pertaining to design, production, and equipment use. WARNING AR0 series industrial switching routers are class B products. In a domestic environment, these products may cause radio interference in which case the user may be required to take adequate measures. AR0 series industrial switching routers are class A products. In a domestic environment, these products may cause radio interference in which case the user may be required to take adequate measures. CAUTION During installation and maintenance, take ESD protection measures, for example, wear ESD gloves or an ESD wrist strap. During router transport and installation, prevent the router from colliding with objects like doors, walls, or shelves. Do not place other objects on the router. The installation, connection, and login methods of AR0/AR0 series industrial switching routers are similar. This document uses the AR-FC-H/AR0-8FE-D-H router as an example. For more information, see the Hardware Installation and Maintenance Guide. Figures in this document are for reference only and may not show the actual appearance of the router. Site Environment Do not place this product in an environment with flammable or explosive gases, or smoke. The installation site must be free from leaking or dripping water or heavy dew. If the relative humidity is high, use dehumidifiers or air conditioners with dehumidification features.

3 The installation site must be well ventilated, and the air vents of the router must not be blocked. Do not place the router in a dusty environment. 00mm Leave more than 00 mm clearance at two sides and rear of the router for heat dissipation. Installing the Router. Installing the AR0 Series Industrial Switching Router Scenario : Mounting the Router on a DIN Rail Screw lock nuts on the hex bolts and fix the hex bolts on the mounting bracket. Before the installation, ensure that the DIN rail has been secured in position. The router is placed near the DIN rail for convenient movement. Lock nut Hang the mounting bracket on the DIN rail. Use a combination wrench to screw the two hex bolts on the mounting bracket. When the DIN rail is fixed with the raised hex bolts, tighten the lock nuts by rotating the wrench counterclockwise. Align an Mx0 screw with the topmost tapped hole on the mounting bracket, and screw it about mm into the tapped hole with a Phillips screwdriver. Use two Mx0 screws to fix the stainless steel sheet on the router. FE FE Power Outage GE0 FE FE FE L GE MONITOR B A B A RS8-0 RS8- DI-0 DI- CONSOLE FE L Survival L N Loosen the screws on the front top cover with the Phillips screwdriver, remove the front top cover, and keep it in an appropriate place for later use. Hang the router onto the topmost screw on the mounting bracket and adjust position of the router to align the mounting holes on the router with those on the mounting bracket. Use two Mx0 screws to fix the router onto the mounting bracket and tighten the topmost screw on the mounting bracket.

4 AR0 Series D INFRARE -H AR-FC PWR RUN/ALM RS8-0 RS8- Scenario : Mounting the Router on a Wall CAUTION The panel with interfaces must face down to protect the interfaces from water. Ensure that there are no flammable or explosive materials near the router and no sundries within 00 mm around the router. Attach the mounting bracket against the wall and adjust its position to keep the top and bottom edges horizontal. Mark positions of the four mounting holes with a marker. 0mm 0mm Secure the mounting bracket on the wall. a Adjust position of the mounting bracket to align the mounting holes on it with the four marked positions on the wall. b Use four M screws to secure the mounting bracket on the wall. Align an Mx0 screw with the topmost tapped hole on the mounting bracket, and screw it about mm into the tapped hole with a Phillips screwdriver. Use two Mx0 screws to fix the stainless steel sheet on the router. FE FE Power Outage GE0 FE FE FE L CONSOLE FE L L N GE Survival MONITOR B A B A RS8-0 RS8- DI-0 DI-

5 Loosen the screws on the front top cover with the Phillips screwdriver, remove the front top cover, and Hang the router onto the topmost screw on the mounting bracket and adjust position of the router to keep it in an appropriate place for later use. align the mounting holes on the router with those on the mounting bracket. Use two Mx0 screws to fix the router onto the mounting bracket and tighten the topmost screw on the mounting bracket. AR0 Series ED INFRAR AR-FC -H PWR M RUN/AL RS8-0 RS8- Scenario : Mounting the Router in a Cabinet (Using a 0 Horizontal Rack-Mounting Kit) CAUTION There must be a clearance larger than or equal to the router's width at the left and right of the router after the installation. The clearance above the router must be at least two times the router's height and the clearance below the router must be greater than or equal to the router's height. Use two Mx0 screws to fix the stainless steel sheet on the router. FE FE Power Outage GE0 GE Survival MONITOR B A B A RS8-0 RS8- DI-0 DI- LE FE FE FE L CONSO FE L L N Loosen the screws on the front top cover with a Phillips screwdriver, remove the front top cover, and keep it in an appropriate place for later use. Hang the router onto the topmost screw on the 0 horizontal rack-mounting kit and adjust position of the router to align the mounting holes on the router with those on the rack-mounting kit. Use two Mx0 screws to fix the router onto the rack-mounting kit and tighten the topmost screw on the rack-mounting kit. U

6 Install two floating nuts on each front mounting rail of the cabinet. Leave four mounting holes between the two floating nuts on the same mounting rail. The length of six adjacent mounting holes may not be U. Observe the scale ticks on the mounting rails when installing floating nuts. You can use a flat-head screwdriver to install floating nuts. Use the Phillips screwdriver to install M screws on the two lower floating nuts, and leave mm of the screws out of the floating nuts. Move the router into the cabinet with one hand supporting bottom of the router, and hook the brackets at both sides of the mounting kit on the M screws. Use the Phillips screwdriver to tighten the lower M screws and then the upper M screws. m m Scenario : Installing the Router in a Cabinet (Using a 0 Horizontal Rack-Mounting Kit) CAUTION There must be a clearance larger than or equal to the router's width at the left and right of the router after the installation. The clearance above the router must be at least two times the router's height and the clearance below the router must be greater than or equal to the router's height. Install two floating nuts on each front mounting rail of the cabinet. Leave four mounting holes between the two floating nuts on the same mounting rail. The length of six adjacent mounting holes may not be U. Observe the scale ticks on the mounting rails when installing floating nuts. You can use a flat-head screwdriver to install floating nuts. U Attach the brackets of the 0 horizontal rack-mounting kit on the front mounting rails of the cabinet and insert M screws in the mounting holes. Use a Phillips screwdriver to tighten the lower M screws and then the upper ones to fix the rack-mounting kit.

7 Screw lock nuts on the hex bolts and fix the hex bolts on the mounting bracket. Hang the mounting bracket on the DIN rail. Use a combination wrench to screw the hex bolts on the mounting bracket. When the DIN rail is fixed with the raised hex bolts, tighten the lock nuts by rotating the wrench counterclockwise. Align an Mx0 screw with the topmost tapped hole on the mounting bracket, and screw it about mm into the tapped hole with the Phillips Lock Nut screwdriver. 8 Use two Mx0 screws to fix the stainless steel sheet on the router. Loosen the screws on the front top cover with the Phillips screwdriver, remove the front top cover, and keep it in an appropriate place for later use. 9 Hang the router onto the topmost screw on the mounting bracket and adjust position of the router to align the mounting holes on the router with those on the mounting bracket. Use two Mx0 screws to fix the router onto the mounting bracket and tighten the topmost screw on the mounting bracket. 9 8 AR0 Series D INFRARE AR-FC -H PWR RUN/ALM RS8-0 RS8- FE FE Power Outage GE0 FE FE FE L FE L GE Survival MONITOR B A B A RS8-0 RS8- DI-0 DI- CONSOLE L N Scenario : Mounting the Router in a Cabinet (Using a Mounting Kit) CAUTION There must be a clearance larger than or equal to the router's width at the left and right of the router after the installation. The clearance above the router must be at least two times the router's height and the clearance below the router must be greater than or equal to the router's height. Loosen the screws on the front top cover with a Phillips screwdriver, remove the front top cover, and keep it in an appropriate place for later use.

8 FE FE Power Outage GE0 GE Survival MONITOR B A B A RS8-0 RS8- DI-0 DI- LE FE FE FE L CONSO FE L L N Use two M screws to fix the stainless steel sheet on the mounting kit. Align the mounting holes on the lower part of the router with the tapped holes on the mounting kit, and secure the router on the mounting kit with two Mx0 screws. Use M screws to secure the mounting kit in the cabinet.. Installing the AR0 Series Industrial Switching Router Installing the Router on a DIN Rail Place the router's real panel in front of the DIN rail and ensure that the DIN rail fits in between the fixture near the top of the router and spring latch near the bottom. Before the installation, ensure that the DIN rail has been secured in position. The router is placed near the DIN rail for convenient movement. Make the router incline forward with the bottom away from the DIN rail, and place the fixture at the rear of the router on the top of the DIN rail. Slowly push the router toward the DIN rail to make the spring latch at the rear of the router move down. The spring latch then bounces back to fix the router on the DIN rail.

9 If the spring latch is too tight to move down, you can pull down the spring latch during the installation.. Installing a 80 W PoE Midspan Installing the 80 W PoE Midspan on the DIN Rail Place the rear panel of the 80 W PoE midspan in front of the DIN rail and ensure that the DIN rail fits in between the fixture near the top of the PoE midspan and the spring latch near the bottom. Before the installation, ensure that the DIN rail has been secured in position. Place the 80 W PoE Midspan near the DIN rail for convenient movement. Make the 80 W PoE midspan incline forward with the bottom away from the DIN rail, and place the fixture at the rear of the 80 W PoE midspan on the top of the DIN rail. Slowly push the PoE midspan toward the DIN rail to make the spring latch at the rear of the PoE midspan move down. The spring latch then bounces back to fix the PoE midspan on the DIN rail. If the spring latch is too tight to move down, you can pull down the spring latch during the installation. 8

10 Connecting the Router. Connecting the AR0 Series Industrial Switching Router WARNING Do not connect cables while the power is on. Do not power on the router before you finish connecting and routing cables. Invisible laser beams will cause eye damage. Do not look into bores of optical modules or connectors of optical fibers without eye protection. For details about pin assignments and cable connections, see the Hardware Description. CONSOLE FE FE FE FE FE Power outage Survival RST RESERVE FE0 FE L GE0 GE L L A B A B RS8-0 RS8- External power supply system -pin AC power cables Ethernet cable Switch or PC RS8 and DI cables Terminals like electric meters and digital input devices Remarks No. M lug: to the router M lug: the end with a smaller hole M lug: to the M lug: the end with a protection ground larger hole A Ground cable Connect To 8 B Item DI- A No. L L L N DI-0 N B MONITOR FE Item Connect To Remarks USB extension USB flash drive cable Some industrial switching router models use DC power supply. Connect -pin DC power cables to these routers. Ensure correct correction of the positive and negative cables. Maintenance Console cable terminal (generally a PC) When the router is powered on for the first time, connect the console interface to a PC for onsite configuration. Connect to an electrical interface to receive and send data services. Ethernet cable Up stream network device Optical fiber 9 The combo interface consists of an FE optical interface and an FE electrical interface.the optical fiber must be used with an optical module.

11 . Connecting the AR0 Series Industrial Switching Router WARNING Do not connect cables while the power is on. Do not power on the router before you finish connecting and routing cables. Invisible laser beams will cause eye damage. Do not look into bores of optical modules or connectors of optical fibers without eye protection. For details about pin assignments and cable connections, see the Hardware Description. A A B B No. Item Ethernet cable Optical fiber Connect To Remarks No. Item Connect To Remarks Switch or PC Connect to an electrical interface to receive and send data services. Boolean output cable External digital input devices -pin DC power cable 0 W AC power module Upstream network device A combo interface consists of an GE optical interface and an GE electrical interface.the optical fiber must be used with an optical module. Connect the positive and negative cables to corresponding terminals correctly. Ground cable M lug: to the router M lug: to the protection ground M lug: the end with a smaller hole M lug: the end with a larger hole 8 -pin AC/DC input power cable External power supply system Insert the -pin connector in the correct direction and do not insert it reversely. Ethernet cable Console cable Maintenance terminal (generally a PC) When the router is powered on for the first time, connect the console interface to a PC for onsite configuration. 0

12 . Connecting the 80 W PoE power supply WARNING Do not connect cables while the power is on. Do not power on the router before you finish connecting and routing cables. For details about pin assignments and cable connections, see the Hardware Description. 0 OUTPUT IN V;. A OUT ~00-0 V 0/0 Hz A No. Item Connect To Remarks No. Item Connect To Remarks Ethernet cable Switch Ethernet cable PD Console cable Maintenance terminal (generally a PC) When the router is powered on for the first time, connect the console interface to a PC for onsite configuration. -pin AC input power cable External power supply system -pin DC output power cable AR0&AR0 series industrial switching routers V DC output Ground cable M lug: to the router M lug: to the protection ground M lug: the end with a smaller hole M lug: the end with a larger hole

13 Powering On the Router. Powering On the AR0 Series Industrial Switching Router Ensure the following before powering on the router: The power cables are correctly connected. The AC input voltage is in the range of 90 V to 90 V (single-phase) or 0 V to V (three-phase). Some routers use DC power supply and require that the DC input voltage be in the range of 9. V to 0 V. If the ARGPe-U-H, ARGR-U-H, and ARG-U-D-H have been placed in a low-temperature environment (below -0 C) for more than. hours before they are powered on, their G module can work normally 0 minutes after startup. Turn on the power switch of the external power supply system. Check the PWR and RUN/ALM indicators. If they are in normal PWR RUN/ALM RS8-0 states, check other indicators on the router. RS8- Indicator states when the router is running normally AR0 Series INFRARE D -H AR-FC PWR RUN/ALM RS8-0 RS8- Indicator Description PWR Steady green: The system power supply is normal. RUN/ALM Slow blinking green: The system is running properly. For more information about indicators, see the Hardware Description.. Powering On the AR0 Series Industrial Switching Router Ensure the following before powering on the router: The power cables are correctly connected. The DC input voltage is in the range of 9. V to 0 V. Turn on the power switch of the external power supply system. Check the RUN indicators. If they are in normal states, check other indicators on the router. Indicator states when the router is running normally Indicator RUN Description Slow blinking green: The system is running properly. For more information about indicators, see the Hardware Description.

14 Logging In to the Router Use a console cable to connect a PC to the console interface of the router. If your PC's operating system provides terminal simulation software (like HyperTerminal in Windows 000), you do not need to install additional terminal simulation software. If the PC runs on an operating system without terminal simulation software (like Windows ), install third-party terminal simulation software on the PC by referring to user manual or online help. A PC may have more than one serial port. Select the port connected to the console port. Generally, COM is used. If you modify the serial port communication parameters on the router, modify the communication parameters on the PC to ensure that they use the same communication parameters, and then set up the connection again. Start the terminal simulation software, create a connection, specify the connected port, and set communication parameters as follows: Bits per second (B): 900 Data bits (D): 8 Parity (P): None Stop bits (S): Flow control (F): None Press Enter until a message is displayed asking you to enter the username and password. (The following information is for reference only.) The default user name is admin and the default password is Admin@huawei. Login authentication Username:admin Password: <Huawei> Info: The entered password is the same as the default. You are advised to change it to ensure security. CAUTION If you forget the login password, restore the password according to the Troubleshooting. After successful login, you can configure the router on the command line interface. For more information, see the CLI-based Configuration. To configure the router using the web system, perform the following steps (only applicable to AR0 and AR0 series industrial switching routers of V00R00C0 and later versions). Connect a PC to the management interface of the router using an Ethernet cable. Configure a management IP address for the router. For example, set the management IP address to 9.8../ on GE0/0/0. <Huawei> system-view [Huawei] interface gigabitethernet 0/0/0 [Huawei-GigabitEthernet0/0/0] ip address Now, the management IP address of the router is set to

15 Configure an HTTP user. <Huawei> system-view [Huawei] aaa [Huawei-aaa] local-user admin password irreversible-cipher [Huawei-aaa] local-user admin privilege level [Huawei-aaa] local-user admin service-type http [Huawei-aaa] quit [Huawei] quit The HTTP user level is management level. Configure a server SSL policy. [Huawei] ssl policy userserver type server [Huawei-ssl-policy-userserver] pki-realm default 8 Apply the SSL policy userserver to the HTTPS server. [Huawei] http secure-server ssl-policy userserver 9 Enable the HTTPS server function on the router. [Huawei] http secure-server enable This operation will take several minutes, please wait... Info: Succeeded in starting the HTTPS server [Huawei] quit 0 Configure an IP address for the PC. The IP address must be in the range of to Start the Internet Explorer (8.0 or later), Google Chrome ( or later), or Mozilla Firefox ( or later), enter in the address box, and press Enter to display the login page. Enter the user name admin and password Admin@huawei (case sensitive). Now, you can configure the router on the web page. For more information, see the Web-based Configuration of the product.

16 Obtaining Product Documentation and Technical Support Log in to Huawei enterprise technical support website ( and select a specific product model and version to find its documentation. Log in to Huawei enterprise support community ( and post your questions in the community. Huawei Enterprise Technical Support Open Source Software Notice In V00R00C0 and later versions, you can run the display copyright command to view the open source software notice. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Copyright Huawei Technologies Co., Ltd. 0. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.