ENGLISH - INDOOR SENSOR INSTALLATION MANUAL BLN2i-WF

Transcription

1 ENGLISH - INDOOR SENSOR INSTALLATION MANUAL BLN2i-WF

2 - TABLE OF CONTENTS Contents Step 1 - Preparations 3 Step 2 - Remove side panels and top lid for mounting access 4 Step 3 - Create cable access 5 Step 4 - Mount the unit safely at the measuring point 6 Step 5 - Connect the unit to the PoE LAN network 7 Step 6 - Check the power-on sequence 8 Step 7 - Fasten the lid and side panels of the unit 9 Step 8 - Await unit configuration 10 Step 9 - Complete the installation 11 Storage of BlipTrack BNL2iWF: There are no special storage concerns to be observed for this unit This and other handling manuals (preparation, installation, troubleshooting, storage, maintenance and other general information) can be found on BLIP Systems web-page: Page 2 of 11

3 STEP 1 - PREPARATIONS 1. Check by visual inspection that the unit is undamaged. 2. The serial number and the MAC address are found from the label on the back of the unit. 3. Check the unit has the correct serial number as agreed with BLIP Systems. 4. Record the MAC address of the unit for the configuration stage. 5. The unit has been fully tested at BLIP Systems prior to shipment so the unit can be installed out-of-the-box at the measurement point without any further preparations. 6. A LAN cable with PoE (Power over Ethernet) shall be available at the measurement point. Back MAC Address Serial number Page 3 of 11

4 STEP 2 - REMOVE SIDE PANELS AND TOP LID FOR MOUNTING ACCESS The two side panels are released by pressing the small wings and lifting the side panels upwards. Remove the lid by unscrewing the four screws. (Lift the lid carefully to avoid damaging the green antennas) Small wing Four screws Page 4 of 11

5 STEP 3 - CREATE CABLE ACCESS To ease creating the cable access the L2i module may be removed. 1. Remove the USB cable from the L2i-module. 2. Remove the L2i module from the unit by lifting it upwards. 3. Cut the rubber cable entry open for normal LAN cable access/or drill a hole in the cabinet if the LAN cable shall enter the unit through the back pane. 4. Mount the L2i module again by pressing it firmly onto the four taps. 5. Reattach the USB cable. Tabs for the L2i module USB Cable Entry for LAN Cable Page 5 of 11

6 STEP 4 - MOUNT THE UNIT SAFELY AT THE MEASURING POINT It is recommended to use the prepared mounting locations within the cabinet when mounting the unit. If the PoE LAN cable shall enter the unit through the cabinet then feed the cable through before mounting the unit. The unit is normally placed in the ceiling having unobstructed view in all directions. If mounted on a wall the cable entry shall face downwards for moisture protection. The unit shall be placed 3-10 meters above ground level. When mounting the unit it must be placed at least 1 meter apart from any other radio based equipment. Location for drilling mounting holes Page 6 of 11

7 STEP 5 - CONNECT THE UNIT TO THE POE LAN NETWORK 1. If the PoE LAN cable shall enter through the cable entry of the cabinet then feed it through now. 2. Attach the cable in the LAN slot of the L2i module. 3. As soon as the active PoE LAN cable is attached the unit will be powered and begin to operate LAN Cable Plug Page 7 of 11

8 STEP 6 - CHECK THE POWER-ON SEQUENCE The unit is powered on when attaching the PoE LAN cable (The outer green LED will go on). All four Status LED s will flash once after approx. 20 sec as part of the basic wake up. Then both green Status LED s will start blinking. The correct operational status is: The inner green LED = On (Connected to BlipServer). The outer green LED = Blinking (Power & OS is OK). Blue LED = Irrelevant for the Indoor Sensor (No Bluetooth activity). Yellow LED = Irrelevant for the Indoor Sensor (No modem). The unit will try to connect to the BlipServer after the basic wake-up. The unit is shipped without any BlipServer configuration which is needed for successful operation. So at this point check that the outer green LED is on when attaching the PoE LAN cable and that both LED s will start blinking after the wake up flash. Page 8 of 11

9 STEP 7 - FASTEN THE LID AND SIDE PANELS OF THE UNIT 1. Fasten the lid firmly using the four screws. 2. Click the two side panels in place to close the unit. (Be mindful of the green antennas) Four screws Page 9 of 11

10 STEP 8 - AWAIT UNIT CONFIGURATION Check that the MAC address of the unit (recorded in Preparations stage) can be seen from the local LAN server. Blip Support can now provide the needed BlipServer configuration remotely. 1. Contact BLIP Support when the unit is ready for configuration providing the serial number. Blip Support can be reached from support@blipsystems.com or phone Blip Support will report back when the configuration has been completed. The unit is now linked to the BlipServer and ready for operation. MAC Address Page 10 of 11

11 STEP 9 - COMPLETE THE INSTALLATION The unit is now in operation. 1. Take a photo of the mounted unit showing the serial number. 2. Take a photo of the mounted unit in it s surroundings. The photos may ease the maintenance phase. An installation report may be forwarded to BLIP Systems: support@blipsystems.com The sensor must be placed at least 1 meter from other radio based devices. The sensor shall be placed 3-10 meters above ground level and have unobstructed view in all directions. Page 11 of 11