WEBS-ZPS Zone Paging System Instructions
|
|
- Shona Townsend
- 6 years ago
- Views:
Transcription
1 I. Introduction Model WEBS-ZPS Zone Paging System is a modular telephone zone paging and control system for use with analog WEBS stations (such as WEBS-MT/R, WEBS-WM and WEBS-PA-2A). It is expandable up to 99 zones and can page individual zones, groups of zones (up to 32), or all zones at once. II. Contents Before beginning installation, make sure you have all the included components. The WEBS-ZPS includes: Qty. Part 1 WEBS-ZPS 1 AC Adapter III. Mounting The WEBS-ZPS is designed to be wall mounted with the modules side-by-side like books. They should be oriented so the zone modules are on the right as shown in Figure 1(a) and 1(b). Figure 1(a) illustrates a WEBS-ZPS unit with a 7-pin dual inline pin (DIP) switch on the first module and Figure 1(b) illustrates a WEBS-ZPS unit without a 7-pin DIP switch on the first module. There is no functional difference between the two. A rack mounting kit is available as Model WEBS-RMKT. This system is powered by plugging the AC adaptor into the module second from the left. Figure 1(a). WEBS-ZPS (with 7-pin DIP switch). Figure 1(b). WEBS-ZPS (without 7-pin DIP switch). Talk-A-Phone Co North Natchez Avenue Niles, Illinois Rev. 1/6/2010
2 IV. System Wiring Option A: If the first module of the WEBS-ZPS unit has a 7-pin DIP switch (TEL INT SEL) as shown in Figure 2, please refer to the following set of instructions: Figure 2. WEBS-ZPS with 7-pin DIP switch (TEL INT SEL). As shown in Figure 2, take the telephone cord from the interface system and wire it to the RJ11 TEL- LINE jack to pins 3 and 4 (red and green). Use a 4 or 6-pin modular cord to connect the RJ11 to the TEL- LINE input. For PBX Station Access/CO Line Configuration, set the TEL-INT DIP switches on the WEBS-ZPS for the following configuration: switch 6 ON (to the right) and 1, 2, 3, 4, 5, 6 and 7 OFF (to the left). Locate the SYS-ID DIP switches and set them to the off position (to the left). For PBX Loop Start Trunk Configuration, set the TEL-INT DIP switches on the module as: switches 3, 4, and 5 ON (to the right) and 1, 2, 6 and 7 OFF (to the left). For PBX Ground Start Trunk Configuration, set the TEL-INT DIP switches on the module as: switches 2, 4, and 5 ON (to the right) and 1, 3, 6 and 7 OFF (to the left). Talk-A-Phone Co North Natchez Avenue Niles, Illinois Page 2 of 7
3 Option B: If the first module of the WEBS-ZPS unit does not have a 7-pin DIP switch (TEL INT SEL) as shown in Figure 3, please refer to the following set of instructions: Figure 3. WEBS-ZPS without 7-pin DIP switch (TEL INT SEL). Use a modular RJ11 telephone cord (minimum 2-conductor) to connect the module to the phone interface system. For PBX Station Access/CO Line Configuration, move the TELEPHONE INTERFACE SLIDE switch on the module to the position shown in Figure 4 (i.e. STATION). The two center conductors of the RJ11 cord are TIP and RING and are not polarity sensitive. Plug one end of the RJ11 telephone cord to the PBX or CO modular jack and the other end in to the STATION jack on the module. Figure 4. WEBS-ZPS (without 7-pin DIP switch) for a PBX Station Access/CO Line configuration. Talk-A-Phone Co North Natchez Avenue Niles, Illinois Page 3 of 7
4 For PBX Loop Start Trunk Configuration, move the TELEPHONE INTERFACE SLIDE switches on the module to the positions shown in Figure 5 (i.e. LS and TRUNK). The two center conductors of the RJ11 cord are TIP and RING 48VDC and have a specific polarity. Plug one end of the cord into the Loop Start Trunk of the PBX and the other end into the TRUNK jack on the module. Figure 5. WEBS-ZPS (without 7-pin DIP switch) for a PBX Loop Start Trunk configuration. For PBX Ground Start Trunk Configuration, move the TELEPHONE INTERFACE SLIDE switches on the module to the positions shown in Figure 6 (i.e. GS and TRUNK). The two center conductors of the RJ11 cord are TIP and RING 48VDC and have a specific polarity. Plug one end of the cord into the Ground Start Trunk of the PBX and the other end into the TRUNK jack on the module. Figure 6. WEBS-ZPS (without 7-pin DIP switch) for a PBX Ground Start Trunk configuration. The second module should have all its SYS ID 4-pin DIP switches set to zero. Connect the 12VDC power supply to the module. Remove the switch lock and place the PROGRAM/RUN switch on the second module to the RUN position. Set the TALK BACK 3-pin DIP switch to the OFF position (to the left) for all the zones. Set the OUTPUT switch to LO PWR position. Locate the terminals labeled ZONE A and connect them to the WEBS-MT/R tower. Each WEBS-MT/R tower is allocated to a single zone on the WEBS-ZPS. Zone A will be Zone 1 and can be paged by following the directions in Section VI of this manual. Zone B will be Zone 2, Zone C will be Zone 3, and Zone A of the next module will be Zone 4, etc. Follow the same procedure for the remaining zones. Refer to Figure 7(a) or 7(b), to connect the WEBS-ZPS to the WEBS-MT/R Amplifier (black chassis) or the WEBS-MT/R Amplifier (silver chassis) respectively. Talk-A-Phone Co North Natchez Avenue Niles, Illinois Page 4 of 7
5 Figure 7(a). Connecting the WEBS-ZPS to the WEBS-MT/R Amplifier (black chassis) Figure 7(b). Connecting the WEBS-ZPS to the WEBS-MT/R Amplifier (silver chassis) via the DIN Rail Terminal Block Talk-A-Phone Co North Natchez Avenue Niles, Illinois Page 5 of 7
6 V. Zone Paging System Programming 1. To switch to programming mode, remove the switch lock and place the PROGRAM/RUN switch to PROGRAM position. In the case of a WEBS-ZPS unit without a 7-pin DIP switch (TEL INT SEL) on the first module, all programming is accomplished through the TRUNK jack on the first module, using the appropriate installed interface. To simplify initial programming, it is suggested that you change the interface type to loop start trunk as shown in Figure 5 and connect a single-line telephone to the TRUNK jack. Once initial programming is completed, re-select the proper interface type and connect the access line. 2. The third, fourth, and fifth modules (zone modules) are not changed during programming. 3. Access the WEBS-ZPS system by either going off-hook with a single line telephone connected to the WEBS-ZPS or by dialing the paging access number for the telephone system. Programming Zone Groups 2. The WEBS-ZPS will emit 3 beep tones, indicating access to the programming mode. 3. Dial [*] followed by the 2-digit number of the zone group (01-32) you want to create. Follow this with the two-digit numbers of the zones you want to be in the zone group. To save the data press [#]. Example: If you want to create zone group 7 consisting of zones 2, 3, and 12, you would dial: [*][0][7][0][2][0][3][1][2][#]. 4. When finished programming return the PROGRAM/RUN switch to RUN. To Erase a Zone Group 2. The WEBS-ZPS will emit 3 beep tones, indicating access to the programming mode. 3. Press [*] and the 2-digit zone group number you wish to erase and then press [#]. 4. When finished programming return the PROGRAM/RUN switch to RUN. To Disable the 30-Second Paging Time Out and 6-Second VOX Feature 2. The WEBS-ZPS will emit 3 beep tones, indicating access to the programming mode. 3. Dial 05000# 4. Dial 0510# 5. If the system accepts the code, you will hear a short double beep. Otherwise if the code is not accepted, you will hear a busy tone. If the code is not accepted, hang up, re-access the system and try again. 6. Hang up the phone and place the PROGRAM/RUN switch in the RUN position. Talk-A-Phone Co North Natchez Avenue Niles, Illinois Page 6 of 7
7 VI. Zone Paging System Operation Make sure the PROGRAM/RUN switch is in RUN position. To Page a Zone 2. Listen for the confirmation tone (i.e. a double beep). 3. Dial the number of the zone you wish to page. All dialing must be two digits. For example: [0][1] for zone 1 (Zone A of the first zone module) [0][2] for zone 2, etc. If a zone number does not exist, the caller will hear a busy tone. 4. Make the page. Hang up when finished. To Make an All-Call Page 2. Listen for the confirmation tone (i.e. a double beep). 3. Dial [0][0] and make an All-Call page. 4. Make the page. Hang up when finished. To Page a Zone Group 2. Listen for the confirmation tone (i.e. a double beep). 3. Dial [*] and the zone group number you wish to page. Zone group numbers consist of two digits. [*][0][1] for zone group 1, [*][0][1] for zone group 2, etc. up to 32 zones. 4. Make the page. Hang up when finished. Talk-A-Phone Co North Natchez Avenue Niles, Illinois Page 7 of 7
CU-8R Installation Instructions
CU-8R Installation Instructions I. Components Model CU-8R is shipped with the following components: QTY Item 1 Stainless Steel Enclosure 2 Lexan Panels 18 Nuts 1 Wall Mount Style Phone with RJ-11 Cable
More informationHOUSING DEVICES, INC. HDI ADA - ARCU. Installation & Operations Manual. Made in the USA
HOUSING DEVICES, INC. ADA - ARCU Installation & Operations Manual Made in the USA ADA - ARCU 5 & 10 Pre-Installation Requirements: For each ADA-1000 in the elevator you must run a twisted, shielded, 22
More informationALCATEL 2315 USER GUIDE
Computer & Telephone Services Ltd NZ 0800 366363 support@cts.co.nz ALCATEL 2315 USER GUIDE 1 1. LAYOUT 2. INSTALLATION 3. OUTGOING CALL 3.1 Handset Mode 3.2 Handsfree Mode 4. INCOMING CALL 4.1. Handset
More informationDynalec MSIC (Monitor Speaker I/F Circuit) ( ) User s Manual
Dynalec MSIC (Monitor Speaker I/F Circuit) (62325-225) User s Manual Rev 27FEB02 GENERAL This manual contains information concerning a description of operation for the Dynalec Monitor Speaker Interface
More informationAristel Networks Pty Ltd NEOS Port GSM / 3G* Fixed Wireless Terminal
NEOS 4000 For models: 4 Port GSM / 3G* Fixed Wireless Terminal NEOS 4000-01 (GSM900/1800) NEOS 4000-02 (GSM 850/900/1800/1900) *NEOS 4000-3G (Next G & 3G) Operating Manual NEOS4000 SERIES Operating MANUAL
More informationModel SP416 (4 lines x 16 extensions) Automated Telephone System
Model SP416 (4 lines x 16 extensions) Automated Telephone System SOHO-PBX is your ideal small or home office receptionist. The SP416 is features packed and very easy to use. For more information please
More informationPAGEPAC PLUS CONTROLLER (V ) AND CONTROLLER WITH POWER SUPPLY (V )
PagePac by Issue 1 PAGEPAC PLUS CONTROLLER (V-5323100) AND CONTROLLER WITH POWER SUPPLY (V-5323105) INTRODUCTION The PagePac Plus System consists of the Controller, AmpliCenter, and up to 3 Zone Expansion
More informationTECHNICAL. Extend Your Phone System s Features and Forward Calls to Telecommuters. RAD-AMP Amplified Remote Access Device
TECHNICAL Practice TELECOM SOLUTIONS FOR THE 21ST CENTURY RAD-AMP Amplified Remote Access Device June 24, 2002! Extend Your Phone System s Features and Forward Calls to Telecommuters The RAD-AMP extends
More informationCL210A TELEPHONE & ANSWERING MACHINE
CL210A TELEPHONE & ANSWERING MACHINE CONTENTS CONTENTS CONTENTS 1 INTRODUCTION 3 Unpacking the Telephone 4 DESCRIPTION 5 General Description 5 INSTALLATION 7 Setting Up 7 Wall Mounting 7 SETTINGS 8 Ringer
More informationData Isolation Cards. ADSL High Voltage Isolation Card. Single Line Voice Isolation Card With CID, CW & MWI. Floated 130VDC or 120VAC Input P30121
Data Isolation Cards ADSL High Voltage Isolation Card Single Line Voice Isolation Card With CID, CW & MWI Floated 48VDC Input P30120 Floated 130VDC or 120VAC Input P30121 Description & Installation Printed
More informationInstructions Telephone Headset Patch THP 700SY
DynaMetric 717 SOUTH MYRTLE AVENUE MONROVIA, CALIFORNIA 91016-3422 626-358-2559 FAX 626-359-5701 800-525-6925 Instructions The THP-700SY is an interface for recorders from telephones and Automatic Call
More informationCisco 8841 & 8851 IP Phone Quick Reference V 1.2
Cisco 8841 & 8851 IP Phone Quick Reference V 1.2 1. Handset Light Strip 2. Line / Session Buttons 3. Phone Screen 4. Soft Key Buttons* 5. Navigation and Select Button 6. Release Button 7. Hold / Resume
More informationUSER MANUAL FEATURES
USER MANUAL FEATURES Hands-free dialing with Indicator Headset operation with Indicator Automatic headset / handset mode detection Headset / Handset operation Headset transmitter / receiver volume control
More informationCIB 3128 Basic Telephone and Modem Interface 2
CIB 8 Basic Telephone and Modem Interface CIB 8 Comcode 05-656-064 Issue CIB 8 Basic Telephone And Modem Interface The Basic Telephone and Modem Interface (BTMI-) allows you to connect most types of on-premises
More informationPA-SIP PAGING SWITCH. For Technical Assistance call the Manufacturers direct ph AM - 5PM West Coast Pacific Time
PA-SIP PAGING SWITCH For Technical Assistance call the Manufacturers direct ph 800 530 8645 8AM - 5PM West Coast Pacific Time NATCOMM USA LLC Responsible Supplier Code :NC PACKING LIST PA-SIP Paging Switch
More information9417CW Installation and User Guide
9417CW Installation and User Guide 9417CW Telephone Important Tips Wait for at least two rings to allow the phone to identify a caller and display the caller s name and/or number. You will have to subscribe
More informationITC-3002-KIT TEST-ALL IV User Guide
ITC-3002-KIT TEST-ALL IV User uide INDE I. ENERAL INFORMATION B. LED INDICATIONS C. PAIR SWITCHES D. FUNCTION SWITCH E. "A" LEAD CONTROL BUTTON F. BATTERY INDICATOR. BATTERY REPLACEMENT H. TEST-ALL IV
More informationPick up the handset from the base. You should hear a dial tone and the display on the base should say TALK. If display says
WALL Uniden XDECT 1 of 6 1 Unpack the telephone Remove all components from the box and remove the protective plastic. Remove the printed tag from underneath the base. Basic set-up guide 2 Connect the handset
More informationSS-22 USER MANUAL. Revision 01 Original document 04 May 2006 Revision 02 Cosmetic changes 23 January 2008 CONTENTS
SS-22 User Manual Revision History Revision 01 Original document 04 May 2006 Revision 02 Cosmetic changes 23 January 2008 CONTENTS 1. INTRODUCTION... 3 2. FEATURES... 3 3. DESCRIPTION... 3 4. CONNECTIONS...
More informationCongratulations! Installation Connecting the telephone Features: Caller ID service Setting Clock (Date and Time)
Congratulations! You are now the owner of a VEF&CO Phone telephone set, a quality communications product. To ensure trouble-free operation, please read these instructions carefully before beginning installation.
More informationFEATURES. AlphaBlueLight Emergency Towers Installation & Operations Manual FIGURE 1: FRONT & REAR VIEWS
AlphaBlueLight Emergency Towers Installation & Operations Manual FIGURE 1: FRONT & REAR VIEWS FEATURES ADA Compliant (hands free operation) LED call status indicator Powder coated steel construction inside
More informations* o INSTRUCTION MANUAL CLT-9660
s* o INSTRUCTION MANUAL CLT-9660 Cordless telephone Congratulations Your SANYO COMPANDER PLUS cordless telephone is a fine-quality home communications product. It is carefully designed and produced by
More informationDT-TPS. User Manual. Telephone Interface 2-wire series.
DT-TPS Telephone Interface 2-wire series User Manual www.intelligenthomeonline.com 1 About TPS Telephone Interface The TPS Telephone Interface is designed for 2-wire series video door entry systems. Enables
More informationEmergency Dialer DIAL-ALERT MODEL: AD
www.skylinkhome.com Emergency Dialer TM DIAL-ALERT MODEL: AD-103 If you would like to order Skylink s products or have difficulty getting them to work or download information and user manual, please :
More informationV-9964 Digital Feedback Eliminator/Message Stacker
Issue V-99 Digital Feedback Eliminator/Message Stacker General Design The V-99 is designed to eliminate acoustic feedback and act as a message stacker. When a page is made, the message is digitized and
More informationLS (LS and IS6100)
Quick start guide LS6375-3 (LS6325-2 and IS6100) Introduction This quick start guide provides you with the basic installation and use instructions. A limited set of features are described in abbreviated
More informationAristel AN4004 GSM FIXED WIRELESS TERMINAL MANUAL V3.1. This manual contains important information. Please read before using the equipment.
Aristel AN4004 GSM FIXED WIRELESS TERMINAL MANUAL V3.1 This manual contains important information. Please read before using the equipment. Contents 3 Function Description:...4 4 Operation Guide:...4 4.1
More informationCORDLESS ANSWERING SYSTEM TELEPHONE 7620
CORDLESS ANSWERING SYSTEM TELEPHONE 7620 Installation Telephone Operation Memory Answering System Operation Installation Table Installation 1. Choose a spot near an electrical outlet and a telephone jack.
More informationAnalog DECT Phone AGR-8206-SMK. Quick Installation Guide V 1.01
Analog DECT Phone AGR-8206-SMK Quick Installation Guide V 1.01 Copyright AEI Communications 2012. All Rights Reserved. 1 Over View This phone is a full-feature telephone that provides voice communication.
More informationAlcatel DECT 209 Wireless PBX System
Alcatel DECT 209 Wireless PBX System USER GUIDE 1 User Guide Index Contents 4 Installation 5 The Base 5 The Handset 6 Charger 6 Battery Cover 7 Handset Keys 7 LCD Icons 8 Standby Mode 8 Receiving a Call
More informationArea of Refuge Command Unit Installation Instructions Model AOR-24/AOR-32
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED CE PRODUIT DOIT ÊTRE
More informationDS1 USER GUIDE. For Technical Assistance call the Manufacturers direct Ph AM - 5PM West Coast Pacific Time
DS1 USER GUIDE For Technical Assistance call the Manufacturers direct Ph 800 530 8645 8AM - 5PM West Coast Pacific Time NATCOMM USA LLC Responsible Supplier Code :NC TABLE OF CONTENTS Description Pages
More informationCAUTION! Never install telephone wiring during a lightning storm.
1 CAUTION! Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled telephone
More informationSEITING UP UNPACKING... 2 NAMES OF CONTROLS... 3 INSTALLATION... 6 Location Connections CHARGING THE HANDSET BAITERY... 7
S* o INSTRUCTION MANUAL CLT-9670 Cordless telephone Congratulations Your SANYO COMPANDER PLUS cordless telephone is a fine-quality home communications product. It is carefully designed and produced by
More informationASAP 104. Installation and Reference Guide. Register Online at
ASAP 104 Installation and Reference Guide Customer Service U.S.: 1-800-288-6794 E-mail: techsupport@commandcommunications.com Register Online at www.commandcommunications.com Table of Contents Introduction
More informationAPPLICATION PROCEDURE HOUSING INSTALLATION AND EQUIPMENT LOCATION
NH208TVU Amplifier and Power Supply Installation and Use Instructions Used with the HT2006 Series Inside Handset Intercom Stations and 1 or more Door Stations APPLICATION The NH208TVU series intercom system
More informationPlantronics Wireless Headset Installation Guide
Basic Set Up: Take the AC Power Supply adapter and plug one end into your wall outlet or power strip. The other end will plug into the back of the headset base, as shown in the following picture. Place
More informationPS 150 SINGLE CHANNEL TELEPHONE INTERFACE. USER MANUAL August 2016
PS 150 SINGLE CHANNEL TELEPHONE INTERFACE USER MANUAL August 2016 This product is designed and manufactured by: ASL Intercom B.V. Zonnebaan 42 3542 EG Utrecht The Netherlands Phone: +31 (0)30 2411901 Fax:
More informationInstructions - THP-700RTS Telephone Headset Radio Transfer Switch with Dry Switch Closure Output
This document applies to all THP-700RTS family members Instructions - THP-700RTS Telephone Headset Radio Transfer Switch The THP-700RTS is an interface between telephones or Automatic Call Directors and
More informationSetting Up Your MX860 In Default Mode (Tel Priority Mode) With An Answering Machine. Next
Setting Up Your MX860 In Default Mode (Tel Priority Mode) With An Answering Machine Connecting The Phone Lines Connecting Your Phone/Answering Machine Is your answering machine built into your phone? YES
More informationModel KS308/416 System Administration Guide
Model KS308/416 System Administration Guide Introduction 3 Installation Hints 4 System Programming 5 IMPORTANT Exchange Lines 6 Assign Incoming calls to ring Nominated Extensions 7 Cascade Ringing Of Extensions
More informationAdvanced Codes Settings for the H650IVN
Advanced Codes Settings for the H650IVN Special Notes: Voice Mail- 30 minutes of record time. When the voice mail becomes full with recorded messages, new messages will not overwrite or erase stored messages.
More informationUser s manual. ML17929 Two-line corded telephone with caller ID/call waiting
User s manual ML17929 Two-line corded telephone with caller ID/call waiting Congratulations on purchasing your new AT&T product. Before using this AT&T product, please read Important safety information
More informationAT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones.
1 USER S MANUAL Part 2 Tapeless Digital Answering System Telephone with Time/Day 1817 Fold open this manual for information about this telephone s installation and operation. Please also read Part 1 Important
More information900 MHz Cordless Answering System with Caller ID/Call Waiting 9357 DRAFT 7/6/01
9357_book/wc_1ATT 7/6/01 4:10 PM Page ii USER S MANUAL Part 2 900 MHz Cordless Answering System with Caller ID/Call Waiting 9357 DRAFT 7/6/01 Please also read Part 1 Important Product Information AT&T
More informationInstallation Guide and User Manual
Installation Guide and User Manual For BT Accord 30 Telephone Amplifier & Headset Telephone and multimedia headset and amplifier kit with noise-cancelling microphone for BT Converse, most other corded
More information900 MHz Digital Two-Line Cordless Speakerphone with Answering System 9452 with Caller ID/Call Waiting
USER S MANUAL Part 2 900 MHz Digital Two-Line Cordless Speakerphone with Answering System 9452 with Caller ID/Call Waiting Please also read Part 1 Important Product Information AT&T and the globe symbol
More informationAll in One Multi-purpose Cable Tester and Cable Tracer
All in One Multi-purpose Cable Tester and Cable Tracer INSTRUCTION MANUAL INDEX Multi-purpose Cable Tester PAGE INTRODUCTION... 1 FEATURES... 1 INSTRUMENT LAYOUT... 2 OPERATION Loopback Test... Remote
More informationPanasonic KX-T30810/T61610 *
Smooth Operator Configuration Note For Smooth Operator Family of Products Octel Voice Processing Module Configuration Note 77205 Panasonic KX-T30810/T61610 * Revised 9/17/97 Panasonic 308/616 Analog Ports
More informationThe SL2100 Quick Install Guide: Terminals Type A (4w)
The SL2100 Quick Install Guide: Terminals Type A (4w) www.nec-enterprise.com SL2100 Digital Terminals Type A (4w) This guide explains the installation, configuration and operation of the SL2100 Type B
More informationOwners Manual: G-Tel 525(Wire-line)
Owners Manual: G-Tel 525(Wire-line) Getting started: 1. Connect the phone s RJ11 phone jack to the local telephone line. 2. Lift hand-set, listen for dial tone, LCD will display PLEASE DIAL. 3. Dial desired
More informationSAT SELECT ENTRY SYSTEMS. User / Installer Guide. Dec 08 SAT3 SAT3/D
SAT3 USER / INSTALLER GUIDE SAT 3 SELECT ENTRY SYSTEMS User / Installer Guide Dec 08 SAT3 SAT3/D SAT3 USER / INSTALLER GUIDE V1.X S elf Identifying A utomatic T elephone 3 & 3/D Select Engineered Systems,
More informationHUAWEI FT2260 Home Phone Connect Quick Start
HUAWEI FT2260 Home Phone Connect Quick Start Introduction Top View The figures are only for your reference, the actual shape and color of the product may differ slightly. 7 8 9 10 1 2 3 4 5 6 1 Power on/off
More informationPlacing Calls. Using Your Single Line Telephone. Placing an Outside Call... Calling a Co-Worker, Voice Mail and Paging...
Using Your Single Line Telephone Placing Calls Due to the flexibility built into the system, your Dialing Codes and Feature Capacities may differ from those in this guide. Check with your communications
More informationSuperBus 2000 Phone Interface/Voice Module Installation Instructions
SuperBus 2000 Module Installation Instructions Product summary The SuperBus 2000 (PIV) Module provides phone and voice functions for the Concord, Concord 4, and Concord Express (v4) panels. The PIV module
More information2 Channel POTS DIN Fiber Link System
USER GUIDE The leader in rugged fiber optic technology. U-8 07A-040 Channel POTS DIN Fiber Link System SYSTEM INSTALLATION INFORMATION The RLH Channel Plain Old Telephone Service (POTS) DIN Fiber Link
More informationNEOS3000A GSM Least Cost Wireless Router
NEOS3000A GSM Least Cost Wireless Router For model GW-NEOS-TC35A5-Q1 or later Operating Manual. Model GW-NEOS-TC35A5-Q1 or later Operating manual Ver. 1.2 November 2005 page 1 Introduction Thank you for
More informationThe SL2100 Quick Install Guide: Terminals Type B (2w)
The SL2100 Quick Install Guide: Terminals Type B (2w) www.nec-enterprise.com Quick Install Guide SL2100 Terminals Type B rev 1.0 1 This guide explains the installation, configuration and operation of the
More informationTwo-Line Speakerphone with Caller ID/Call Waiting 992
0992_CIB_1ATT_FINAL_022105 2/22/04 4:46 PM Page II User's Manual Part 2 Two-Line Speakerphone with Caller ID/Call Waiting 992 In case of difficulty, visit our Service Center at www.telephones.att.com or
More informationOperating Instructions
Integrated Telephone System Operating Instructions Model No. KX-TS8W Preparation Pulse-or-tone dialing capability INTERCOM LINE Caller ID Compatible PLEASE READ BEFORE USE AND SAVE. Panasonic World Wide
More informationArea of Rescue Command Unit Installation Instructions Model AOR-8 / Model AOR-16
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED CE PRODUIT DOIT ÊTRE
More informationModel No. Manuals and supporting information are provided on the Panasonic Web site at:
Quick Reference Guide Digital Communication Terminal Model No. KX-DTU100 Thank you for purchasing a Digital Communication Terminal. Please read this manual carefully before using this product and save
More informationAristel Networks Pty Ltd. All Round Cabling Solutions NEOS3003-3G01. Operating Manual * NEOS G01
Aristel Networks Pty Ltd All Round Cabling Solutions NEOS3003-3G01 Operating Manual * NEOS 3003-3G01 Supports 3G/UMTS 800/850/900/1900/2100 MHz bands Telstra-Vodafone-Optus supported in all areas. * Model:
More informationLG Ericsson IP Phone IP 8802A
LG Ericsson IP Phone IP 8802A 1 1 Message LED 2 3 8 4 9 5 6 7 10 11 12 13 Programmable Keys 14 2 Keys 1 Description of keys Navigation Controls: Left: Use to go to the previous menu in the settings menu.
More informationDIN Rail Mounted Dial-up Modem Users Manual
DIN Rail Mounted Dial-up Modem Users Manual 366-100 Copyright 2002 Miille Applied Research Co., Inc. Houston, Texas Page 1 This page is left blank intentionally Page 2 Page 1 TABLE OF CONTENTS 1.1 General...
More informationTapeless Digital Answering System with Time/Day Part 2
2 Tapeless Digital Answering System with Time/Day 1715 Fold open this manual for information about this telephone's installation and operation. Please read Part 1 Important Product Information, included
More informationThe Onis Vox handset. Earpiece. Down Key Press this key to move through the menu or to decrease earpiece volume during calls.
Language Automatic Dialling Pause Dial Mode Network Type Recall Type Add Handset Remove Handset Register Handset Change Base Station Name 6 SETUP 5 BASE SEL Standby R PHONEBOOK BABY SIT Add Entry ANSW
More informationStandby. ** Onis only. * Onis Memo only SETUP
Standby R PHONE BOOK Add Entry Remove Entry RINGERS Handset Base Station 7 SETUP Automatic Dialling Pause Dial Mode Network Type Recall Type Add Handset Remove Handset Register Handset Change Base Station
More informationQuick Start Guide. Intermedia Hosted PBX Cisco SPA 303 and SPA 504G Phone
Quick Start Guide Intermedia Hosted PBX Cisco SPA 303 and SPA 504G Phone 2 Welcome to your Hosted PBX Service. What s in the box? Cisco SPA 303 and 504G Phones A. Phone Base B. Handset C. Handset Cord
More informationOracle (tm W ireless Telephone Interface Unit
Oracle (tm ) W ireless Telephone Interface Unit Thank you for purchasing the Oracle Pro Gate System. This product has been designed and manufactured in the USA, utilizing the highest quality standards
More informationQuick Guide. Setting up PNQW1003YA. Model No. KX-TG6322 KX-TG6323 KX-TG6324
TG632x_QG(e).fm Page 1 Thursday, July 17, 2008 10:59 AM Quick Guide Setting up Base unit L Use only the supplied Panasonic AC adaptor PQLV207 or PQLV219. L Use only the supplied telephone line cord. Model
More informationREVISED 5/1/01. AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones.
REVISED 5/1/01 1 USER S MANUAL Part 2 1818 Digital Answering System Speakerphone Fold open this manual for information about this product s installation and operation. Please also read Part 1 Important
More informationSennheiser BW900 Wireless Microphone with Zoom Switch Analog. Set-Up and Instructions for Use
Sennheiser BW900 Wireless Microphone with Zoom Switch Analog Set-Up and Instructions for Use This unique microphone is designed for use with a telephone, but can also be connected to a PC via several mechanisms.
More informationUSER MANUAL EZ - ANNOUNCER RECORDED MESSAGE ANNOUNCER. Model L 240, EZR240. BY EZ ADVANTAGE CORP. 221, Broad Street, Milford, CT U.S.A.
USER MANUAL EZ - ANNOUNCER RECORDED MESSAGE ANNOUNCER Model L 240, EZR240 BY EZ ADVANTAGE CORP. 221, Broad Street, Milford, CT 06460 U.S.A. 1 EZ Announcer User Manual Second Edition : Nov 2001 Version
More informationConnecting the THP-700RTS to a Telephone and Radio Console - Summary. DynaMetric. Made in USA THP-700RTS
Connecting the to a Telephone and Radio Console - Summary RECORDER 700RTS 700RTS PHONE PIN HEADSET PIN JACK PIN PLUG* PIN JACK 1 1 MIC 1 1 Make same 2 2 EAR 2 2 as Phone 3 3 EAR 3 3 Jack 4 4 MIC 4 4 PIN
More informationMitel 200 Light. Voice Board(s) Analog Ports. Personal Computer. Configuration Note Mitel SX200 Light * ONS. Revised 6/2/99
Octel 50 Voice Processing Module Configuration Note 77141 Mitel SX200 Light * ONS Revised 6/2/99 Mitel 200 Light Analog Ports Voice Board(s) Personal Computer Inband signaling is used for integration Supported
More informationSmooth Operator Configuration Note
Smooth Operator Configuration Note For Smooth Operator Family of Products Octel Voice Processing Module Configuration Note 77180 Nitsuko Onyx * (VS, III, IV) Revised 9/17/97 Nitsuko Onyx ASI ASI Dual Port
More informationQuick start guide. ML17939 Two-line corded telephone/ answering system with caller ID/call waiting
Quick start guide ML17939 Two-line corded telephone/ answering system with caller ID/call waiting Installation preparation You must install the power adapter before using the telephone. See pages 4-5 for
More informationSetting Up Your MX882 In Default Mode (Tel Priority Mode) With An Answering Machine. Next
Setting Up Your MX882 In Default Mode (Tel Priority Mode) With An Answering Machine Connecting The Phone Lines Connecting Your Phone/Answering Machine Is your answering machine built into your phone? YES
More informationQuick Start Guide. Intermedia Hosted PBX Yealink T46G
Quick Start Guide Intermedia Hosted PBX Yealink T46G What s in the box? Yealink T46G A. Phone B. Ethernet Cable C. Handset Cable D. Handset E. Stand F. Quick Start Guide G. Power Adapter Welcome to your
More informationDefault Mode (Tel Priority Mode) With An Answering Machine. Next
Setting Up Your MX320 In Default Mode (Tel Priority Mode) With An Answering Machine Connecting The Phone Lines Connecting Your Phone/Answering Machine Is your answering machine built into your phone? YES
More informationGSM FIXED WIRELESS TERMINAL
AN1001 GSM FIXED WIRELESS TERMINAL USER MANUAL V 4.3 This manual contains important information. Please read before using the equipment. AN1001 GSM FWT User Manual Rev 4.3 April 2010 1 Contents 1 Introduction
More informationUser s manual (Canada version) ML17939/ML17959 Two-line corded telephone/ answering system with caller ID/call waiting
User s manual (Canada version) ML17939/ML17959 Two-line corded telephone/ answering system with caller ID/call waiting Congratulations on purchasing your new AT&T product. Before using this AT&T product,
More informationUtilizing NuVo s Paging & Doorbell Mute Capabilities
Utilizing NuVo s Paging & Doorbell Mute Capabilities One of the great benefits of multi-room audio systems is their ability to surround the home with music in every room. However when listening to your
More information900 MHz Cordless Telephone/Answering System with Caller ID/Call Waiting 9371 DRAFT 8/14/01
9371_book_1ATT 8/14/01 10:00 AM Page ii USER S MANUAL Part 2 900 MHz Cordless Telephone/Answering System with Caller ID/Call Waiting 9371 DRAFT 8/14/01 Please also read Part 1 Important Product Information
More informationVoiceLine Calling Features
VoiceLine Calling Features For a complete list of features and codes, refer to the VoiceLine User s Guide. VOICELINE CALLING FEATURES Feature Call Waiting Caller ID 3-Way Calling Description Once you hear
More informationIntercom User Manual v1.1
Intercom 102153-01 User Manual v1.1 Content of delivery - Intercom unit, art no. 102153-01 - DIN clips and screws - Intercom Manual (this document), art no. 162153-01M Art. No. 162153-01M v1.1c 2012-12-20
More informationCisco Model SPA 303 Quick Start Guide
Cisco Model SPA 303 Quick Start Guide Welcome Thank you for choosing the Cisco Small Business IP phone. This guide describes how to install your phone and how to perform some basic tasks. 1 Installing
More informationSIMADO GFX11/GFX11E Quick Start
SIMADO GFX11/GFX11E Quick Start SIMADO GFX11 GSM/3G Fixed Cellular Terminal for Voice Applications SIMADO GFX11E GSM/3G Fixed Cellular Terminal for Emergency Applications Quick Start Documentation Disclaimer
More informationMultiple Digital Messaging Unit
HARRIS DRACON DIVISION Multiple Digital Messaging Unit Installation and Configuration Copyright 994 Harris Dracon All Rights Reserved Written/Printed in U.S.A. 0II7404-00 Issue, Nov. 994 Notice Every effort
More informationOperating & Programming Manual PBX Model: COX-308S / 416S / 432S
. Contents Operating & Programming Manual PBX Model: COX-308S / 416S / 432S We extend a warm welcome to you on becoming a part of the Copper Connections family. Our service support Engineers shall be working
More informationEnterprise Edge M7100 User Card
Enterprise Edge M7100 User Card 1999 Nortel Networks P0908517 Issue 01 Your Enterprise Edge M7100 telephone Release button cancels active calls Display shows the time, date, call information, and guides
More informationAT&T. PARTNER Communications System Remote Administration Unit. Installation and Use
AT&T PARTNER Communications System Remote Administration Unit Installation and Use Copyright 1994 AT&T All Rights Reserved Printed U.S.A. AT&T 518-455-050 Issue 1 April 1994 Notice Every effort was made
More informationAristel AN1001 GSM FIXED WIRELESS TERMINAL MANUAL V4.2. This manual contains important information. Please read before using the equipment.
Aristel AN1001 GSM FIXED WIRELESS TERMINAL MANUAL V4.2 This manual contains important information. Please read before using the equipment. Contents 1 Introduction 2 Warning 3 Function Description 4 Operation
More informationAristel AN1001 GSM FIXED WIRELESS TERMINAL MANUAL V4.2. This manual contains important information. Please read before using the equipment.
Aristel AN1001 GSM FIXED WIRELESS TERMINAL MANUAL V4.2 This manual contains important information. Please read before using the equipment. Contents 1 Introduction. 2 Warning 3 Function Description 4 Operation
More informationQuick Guide KX-TGF574/KX-TGF575 KX-TG785SK. Connections PNQW5232ZA. Printed in Malaysia PT1116AM0. Model No. KX-TGF572/KX-TGF573
Model No. KX-TGF572/KX-TGF573 KX-TGF574/KX-TGF575 KX-TG785SK Quick Guide Connections Base unit Connect the AC adaptor to the unit by pressing the plug firmly. 2 Fasten the cord by hooking it. 3 Connect
More informationAT&T. PagePac Plus System. Installation and Configuration. Contents
AT&T PagePac Plus System Installation and Configuration Contents General Information - 2 Before You Start - 3 Installation Steps - 4 Connecting Speakers - 9 Power Up System - 12 Self Powered Controller
More informationHardened 10/100Base-TX IEEE802.3at PoE PSE Ethernet Extender
Quick Start Guide This quick start guide describes how to install and use the Hardened Ethernet Extender. This is the Hardened Ethernet Extender of choice for harsh environments constrained by space. Physical
More informationTechnical Practice BP-2 POWER FAILURE TRANSFER UNIT. Issue 8, April 1988
www.gkinc.com support@gkinc.com Technical Practice Contents Section 1 General Description Section 2 Applications Section 3 Installation Section 4 Circuit Description Section 5 Specifications Section 6
More informationThe Packs Infotel. GSM Converter V2. Installation Manual V7
The Packs Infotel GSM Converter V2 Installation Manual V7 1 Index Connecting the M60 to the GSM Converter 3 1. GSM Converter description 4 2. Equipment installation 4 3. Led functions. 5 4. GSM Converter
More information