Energy Meter and. Current Transducer. Assembly Manual
|
|
- Leo Warren
- 5 years ago
- Views:
Transcription
1 Energy Meter and Current Transducer Assembly Manual
2 The energy meter assembly is made of two separate boxes and associated accessories, as follows: Energy Meter (EM) Box, with two cables feeding directly out from the box Current Transducer (CT) Box USB Flash Memory 50cm Male Micro-USB to USB Memory Stick cable (supplied as one assembly including custom adapter PCB) Current Transducer (CT) Box Fig.1 shows a picture of the CT box. Each CT box has a center hole of 20mm diameter through which the main current carrying conductor from the high voltage battery must pass. Figure 1: Current Transducer Box Each CT box is marked with an arrow symbol which indicates its positive electrical current flow orientation. Find the arrow on the CT box and install it with its arrow pointing in the direction of positive current flow from the battery under motor drive conditions. The CT box can be installed on either the outgoing (positive) connection from the battery, or the return (negative) connection to the battery. However, the direction of current flow through the CT box for a driven motor must be positive in the direction of the arrow. 2
3 The CT box connects to the EM box via an EM-CT Cable that is permanently wired into the box, and pre-terminated with a Mini-USB plug at the free end as shown in Fig. 1. The cable length is preset, and cannot be modified. Fig. 2 shows a guidance picture of the installation of the CT box for a positive battery terminal connection. Battery Positive Terminal Battery Negative Terminal Energy Meter (EM) Box Figure 2: Orientation of CT Box Fig.3 shows the picture of the Energy Meter box. Each box has four mounting feet, two directly connected cables, one Mini-USB socket and one micro-usb socket, as follows: EM-CT Mini-USB cable socket HV Battery Voltage Connections LV Power Supply Connections Figure 3: Energy Meter Box High Voltage Measurement Cables (1.5 m long): These orange cables come directly out of the EM box, and are used to connect to the main battery (0V to 800V) for the high voltage measurement. They are to be connected to the non-battery side of the current limiting resistors that connect between the external voltage measurement test points and the main DC bus voltage. 3
4 Connect the negative voltage measurement point to the cable core with the black heatshrink sleeving fitted to the cable, and the positive measurement test point to the other cable core. If you shorten these cables before connection, make sure you maintain the correct voltage polarity connection the EM box will not operate correctly if the HV voltage measurement polarity is reversed. Fig. 4 shows the heatshrink polarity sleeving fitted to the HV cables. Figure 4: HV Cable Connections EM-CT Cable connection: The Mini-USB plug end of this cable plugs into the EM box at the TOP RIGHT socket shown in Fig. 3. Note that this is the only Mini-USB socket used for the EM box the two lower sockets shown in Fig. 3 are Micro-USB sockets and will not accept the EM-CT cable plug. Power Connection Cable: This cable comes directly out of the EM box as shown in Fig. 3, and is to connect the low voltage power supply (9V to 36V). Connect the low voltage supply positive terminal to the WHITE cable core, and the low voltage supply negative terminal to the BLACK cable core. USB Port: This port is to connect flash memory for logging energy data via the cable supplied to you. The cable plugs into the lower left hand socket as shown in Fig. 5. If required, this cable can be unplugged from the EM box for installation. However, make sure you re-insert it in the correct orientation, and properly plug into the correct Micro- USB socket as shown in Fig. 5. 4
5 Micro-USB socket for USB Cable Figure 5: USB Port Cable Connection Micro USB Cable This cable is used to connect the flash memory to the EM box. The cable has a length of 1m, and plugs into the USB port on the EM box. The other end of the cable must be mounted to allow free external access to the USB memory stick by the race scrutineers. Typically it can be taped to a car frame strut, using the (supplied) foam backing to minimize vibration. The memory stick assembly is shown in Fig. 6. Figure 6: Male Micro-USB to USB Memory stick (connector wrapped in tape) 5
6 If you have any questions, please do not hesitate to contact Prof. Grahame Holmes at NOTE: The energy meter recording is written as a text file to the USB memory stick, which can be readily read using a standard PC to confirm correct installation. This memory stick MUST be handed to the race officials on Saturday 9 th of the competition to be re-initialised in preparation for the endurance event on Sunday 10 th. 6
PQ-Box 100, 150, 200 & 300 Power Quality Analyser Clamps & Accessories
Mini Clamps: Part Number 111.7015 PQ-Box 100, 150, 200 & 300 Power Quality Analyser Clamps & Accessories Description 10 ma-to-20 A or 100 ma-to-200 A. Switchable range mini clamp. 40 Hz 20 khz 4 x mini
More informationRKP08 Component List and Instructions
RKP08 Component List and Instructions PCB layout Constructed PCB RKP08 Scematic RKP08 Project PCB Page 1 Description The RKP08 project PCB has been designed to use PIC microcontrollers such as the Genie
More informationHome Automation Systems Installation Guide for FFI Actuator & Control Projects
Home Automation Systems Installation Guide for FFI Actuator & Control Projects This installation guide is for home automation systems such as Crestron, Lutron and others which communicate with FFI controllers
More informationDPM-3221 Digital DC Power Meter with data logging capability.
Introduction DPM-3221 Digital DC Power Meter with data logging capability. User Manual As a digital DC power meter, it measures the real time DC Voltage (5-60V), DC Current (0-200 A with the correct shunt),
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationGo-Baby-Go Senior Capstone Project
Go-Baby-Go Senior Capstone Project Assembly Manual Team 22C Alwaleed Alhamra Asrar Alkhabbaz Fawaz Almutairi Sultan Almutairi Eric Trieu Project Sponsor: W.L. Gore & Associates Faculty Advisor: Dr. David
More informationDPM Digital DC Power Meter with Data logging capability. User Manual
DPM-3232 Digital DC Power Meter with Data logging capability User Manual Introduction As a digital DC power meter, it measures the real time DC Voltage (5-60V), DC Current (0-60A), Watt, and it also displays
More informationBuffaloLabs WiFi Lantern Assembly guide version 1
BuffaloLabs WiFi Lantern Assembly guide version 1 Needed equipment: Solder iron Solder wire Cutter Wire stripper (optional) Hot glue gun Overview of the components (not including USB cable and box panels)
More informationZero2Go. User Manual (revision 1.03) Wide Input Range Power Supply for Your Raspberry Pi. Copyright 2017 UUGear s.r.o. All rights reserved.
Zero2Go Wide Input Range Power Supply for Your Raspberry Pi User Manual (revision 1.03) Copyright 2017 UUGear s.r.o. All rights reserved. Table of Content Product Overview... 1 Product Details... 3 Package
More informationThe basic product comes with the IRS5 control board, 3 internal cables, 1 external cable with a 5 volt adapter and a mounting bracket with hardware.
Please read these instructions and watch the Installation Video before you proceed with the installation of the PC-IRS5-01. Installation Video: http://youtu.be/os98e32vhb4 The PC-IRS5-01 Infrared Receiver
More informationLight & Sound Control Module
Light & Sound Control Module Operation and Installation Manual G-Scale Graphics 5860 Crooked Stick Dr. Windsor, CO 80550 970-581-3567 GScaleGraphics@comcast.net www.gscalegraphics.net Revision 55: C: Updated
More informationHow to assemble and disassemble Anafi
How to assemble and disassemble Anafi Prerequisites The best way to repair ANAFI is to use Parrot official drones repair kit. You will need the cruciform as well as the Torx 5 (T5) in order to carry out
More informationConnecting igaging DigiMAG Scales to the Caliper2PC Interface A step by step Guide
What is an igaging DigiMAG Scale? The igaging DigiMAG are digital linear scales that are easily connectable to the Caliper2PC interface. They consist of two parts, the encoder and the readout unit. The
More informationScreenLine Accessories MB model
ScreenLine Accessories MB model ST2121 Control Module 1 group of blinds (PC configuration) control (Potential separated) Individually configurable via Configuration Utility (PC) DIN rail mounting Dim.:
More informationInsert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.
MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationUF-3701 Power Board Construction Guide
Page 1/5 Soldering and Part Placement See the Chapter 3 of the MIT 6270 Manual for information on electronic assembly, including soldering techniques and component mounting. Construction Information All
More information21 TRACK MAINTENANCE GUIDE
Mountain Engineering II, Inc. 21 TRACK MAINTENANCE GUIDE 1233 Sherman Drive, Longmont, CO 80501-6133 303-651-0277 303-651-6371 (fax) www.mountainengineering.com Table of contents Table of contents...2
More informationPhotoelectric Sensors Enhanced 50 Series
June 2008 Contents Overview...................... Model Selection, Sensors......... 2 Model Selection, Compatible Cables.............. 7 Model Selection, Fiber Optic Cables................... 8 Model Selection,
More informationParts List: Part # Tools List: Instructions:
Parts List: Part # 1 pair of Dayton Audio B652s 300-652 1 Dayton Audio DTA-2 amplifier 300-385 1 MP3 module 320-350 1 7805 +5 VDC voltage regulator 7805 1 12 VDC 2A power supply 129-077 1 2.1 mm panel
More informationPost Tenebras Lab. Written By: Post Tenebras Lab
Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.
More informationVector 3D printer complete wire list including extruder PWA listing
Vector 3D printer complete wire list including extruder PWA listing Conventions Pin numbering for connectors It is normal practice in print circuit board (PCB) layout to denote pin 1 of a PCB mounted connector
More informationPSM-2 POWER SUPPLY MODULE INSTRUCTIONS
PSM2-09.doc 1 Rev: 8-28-01 PSM-2 POWER SUPPLY MODULE INSTRUCTIONS PSM Model 2 equipped with Field Programmable Output Voltages MODEL PRODUCT OFFERING / VARIATIONS: PSM-2 Metal case housed surface mountable
More information3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions
3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions Version date Author Comments 1.0 29/05/2013 Boris du Reau Initial version Rocket Type Micro-max Model Mid
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. MP3 ATTACHMENT KIT 2006 RIDGELINE AII 28615 Issue Date FEB 2005 PARTS LIST Attachment Kit: P/N 08B06-SJC-100 MP3 Player Kit (sold separately):
More informationIXIUM. DVR Mini Camera. User Manual
IXIUM DVR Mini Camera User Manual Contents Package Contents... 2 Before You Start... 2 Overview... 3 Controls... 4 SD Card Slot (TF)... 4 USB: Syncing and Charging... 4 Microphone... 4 On/Off... 4 Video
More informationContents. BMS icom Manual
Contents 1. Introduction... 2 2. Safety Overview... 2 3. Package Contents... 3 4. Required Tools... 4 5. Installation Instructions... 6 Step 1: Mount BMS Unit... 6 Step 2: Clamp Setup... 6 Step 3: Sensing
More informationConnector Systems for GPS Tracking, Positioning and Portable Navigation Devices (PND)
and Portable Navigation INTRODUCTION Molex offers a broad range of compact, high-density connectors that can be used for navigation, tracking and positioning. Each connector is packed with features designed
More informationHigh Power (15W + 15W) Stereo Amplifier
High Power (15W + 15W) Stereo Amplifier Build Instructions Issue 1.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit
More information527F CNC. Retrofit controller for machines made by Fadal Machining Centers. Installation and set-up manual Calmotion LLC
527F CNC Retrofit controller for machines made by Fadal Machining Centers Installation and set-up manual 2008-2018 Calmotion LLC Calmotion LLC 7536 San Fernando Road Sun Valley, CA 91352 www.calmotion.com
More informationDigital Keypad Introduction
K2 Digital Keypad Introduction The K02 uses the latest microprocessor technology to operate door strikes and security systems that require a momentary (timed) or latching dry contact closure. All programming
More informationTroubleshooting guide for the S100 Energy meter and EPS
Troubleshooting guide for the S100 Energy meter and EPS The S100 Energy Meter is the brains of the Sungrow hybrid system. It tells the inverter when to charge or discharge the battery, when to go into
More informationSchematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)
Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by
More informationREMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer.
REMOVE COVERS 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. 3. Fully open the Top Cover. 4. Release the tab on the right
More informationThere is no Business Like No Business CONTENTS. By Rafael Lozano-Hemmer
There is no Business Like No Business By Rafael Lozano-Hemmer CONTENTS General important information This short section must be read for proper operation Description Operation Cleaning Internet connection
More informationMSD Enhancer Ignition for the Honda TRX400EX PN /PN 4203
MSD Enhancer Ignition for the Honda TRX400EX PN 05-00-4203/PN 4203 Parts Included: 1 - Programmable Enhancer Ignition 1 - Y-Splice 1 - MSD Coil Assembly 1 - Black Ground Wire 1 - Ignition Mounting Brackets
More informationP522 Signal Processor
P522 Signal Processor INSTALLATI INSTRUCTIS Self-Check Contact Ratings: Max switching power - 60 W 125Vac Max switching voltage - 220VDC, 250Vac Max switching current - 2A DC, AC Analog Flame Signal: User
More informationAXi-RGB2 INSTALLATION MANUAL
Rev. 2.4 080415 AXi-RGB2 INSTALLATION MANUAL PLEASE REVIEW THIS INSTALLATION MANUAL CAREFULLY BEFORE BEGINNING ANY WORK COMPATIBLE PLUG & PLAY WIRING HARNESSES AXi-BMW18-R AXi-CRVT-R AXi-FL24-R AXi-GM1-R
More informationum260 Backup Battery Kit
um260 Backup Battery Kit Overview The System Studies um260 Micro Monitor (Part No. 9800-6260M) is a -48V DC-powered small-office monitor designed for a variety of monitoring applications. To make it possible
More informationView Wall Interface. Dynamic Glass INSTALLATION GUIDE. Description. System Requirements. Installation Overview
Description The solution is a compact, wall-mounted interface used for monitoring and changing the tint levels of View Dynamic Glass. The product leverages 802.11-based Wi-Fi technology for connectivity
More informationInductive Cylinder Position Sensors
Inductive Cylinder Position Sensors 4-Wire DC (NPN and PNP) 2-Wire AC/DC Weld immune 250, 000, and 3000 psi designs C-Series F-Series Rating (psi) Probe Diameter Inductive Cylinder Position Sensors Pepperl+Fuchs
More informationARRIS X-Speed 250B Assembling Manual
ARRIS X-Speed 250B Assembling Manual Thank you for purchasing the ARRIS X-Speed 250B FPV Racing drone. Be sure to read through the entire manual before starting your build. If you bought the ARRIS X-Speed
More informationthe Interactive Catalog
Interactive Catalog Supplements Catalog PDFs If you need detailed product information, or help choosing the right product for your application, see our Interactive Catalog Use the Interactive Catalog to
More informationPhi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012
Phi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012 1. Introduction:... 3 Currently available:... 3 2. Backpack assembly... 4 3. Connecting to a keypad... 6 4. Rotary encoder keypads...
More informationClick-A-Tune. User Manual
Contents Configuring the...2 Transferring data to the...2 with switch configuration...3 with switch matrix up to 3 switches...4 Changing the playback volume...5 Connections... Power requirements (Vin)...
More informationDTox. M type. Minimal D/T timer
DTox M type Minimal D/T timer The DTox M-type timer is an experimental device, just like your free flight model. Determining the suitability of the timer for your particular application is solely your
More informationModel IMP-22G2,H Low Cost Slave Clock Impulser Converts your slave clock to a working timepiece without modifying its original mechanism.
Model IMP-22G2,H Low Cost Slave Clock Impulser Converts your slave clock to a working timepiece without modifying its original mechanism. The PIEXX IMP-22G2, H allows you to put your slave clock back into
More informationMAIN PCB (The small one)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationProduct and Function Description
Product and Function Description and the LED display. The touchscreen can be used to select from up to 6 languages for the display of texts and messages. The room temperature controller integrated in Contouch
More informationSharpSky Focuser Construction. SharpSky Focuser. Construction Document V st December 2012 Dave Trewren 1
SharpSky Focuser Construction Document V0.12 1st December 2012 Dave Trewren 1 Contents 1 General... 3 1.1 Change Record... 3 1.2 References... 3 2 Introduction... 5 3 SharpSky driver installation... 5
More informationsolutions for teaching and learning
RKP18Motor Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKP18Motor Project PCB Page 1 Description The RKP18Motor project PCB has been designed to use PIC microcontrollers
More informationTIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE
TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE Table of Contents 0. Components List + Tools 0. PCB Sides 03. PCB Assembly 04_. Diode N448 04_. Laying Resistors 04_3. Capacitors 04_4. Quartz 04_5. 78L05
More informationDPM Bi-directional Digital DC Power Meter with built-in USB data logger & adapter External shunt model. User Manual
DPM-3321 Bi-directional Digital DC Power Meter with built-in USB data logger & adapter External shunt model User Manual Bi-Directional DC Power Meter with built-in USB data logger & adapter. The new DPM-3321
More informationindustrial panel lamps
features specifications Typical characteristics (Ta = C) Ø8.1mm mounting Robust bright nickel plated brass housing Low profile styling, sunlight readable LEDs Sealed to IP67 Internal reverse protection
More informationLED Light Kit. Install Instructions for LIGHT-KT outdoorrooms.com
LED Light Kit Install Instructions for LIGHT-KT sales@outdoorrooms.com 1.866.303.4028 outdoorrooms.com Table of Contents Included With This Kit....3 Setup Instructions... 4-5 Wiring Diagram.. 5 Install
More informationRover 5. Explorer kit
Rover 5 Explorer kit The explorer kit provides the perfect interface between your Rover 5 chassis and your micro-controller with all the hardware you need so you can start programming right away. PCB Features:
More informationAdafruit USB Power Gauge Mini-Kit
Adafruit USB Power Gauge Mini-Kit Created by Bill Earl Last updated on 2017-07-14 11:55:04 PM UTC Guide Contents Guide Contents Overview Assembly Basic Assembly Solder the female connector. Solder the
More informationDIY Line Tracking Smart Car with AT89C2051
DIY Line Tracking Smart Car with AT89C2051 1. Introduction: A DIY Smart Car design involves mechanical structure, electronic based sensor principle, automatic control, and even knowledge of microcontroller
More informationUSBCNC USB Disk Key reader for CNC Controls Machine Mount instructions
USBCNC USB Disk Key reader for CNC Controls Machine Mount instructions 2008-2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 www.calmotion.com Introduction This
More informationUser manual DinaSys DTC/DTS and DTC/DTZ
PiCommIT has developed the DinaSys DTC/DTS and DinaSys DTC/DTZ turntable controller for the Fleischmann / Marklin Turntables in scale H0, H0m, TT, N and Z. One of the most important starting point was
More informationMAIN PCB (The small one with the square cut out from one side)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationHUB-ee BMD-S Arduino Proto Shield V1.0
HUB-ee BMD-S Arduino Proto Shield V1.0 User guide and assembly instructions Document Version 1.0 Introduction 2 Schematic 3 Quick user guide 4 Assembly 5 1) DIP Switches 5 2) Micro-MaTch Connector Headers
More informationMINDRACER USER MANUAL
MindPX T h e U l t i m a t e Racer MINDRACER USER MANUAL Highlights - Ultra mini size, weight only ~6g - High performance F4 168MHz floating point processor, super fast throttle response - Support OneShot
More informationNetworked Control and Monitoring System. enter digital
Networked Control and Monitoring System enter digital CZone is the latest innovation from BEP. At BEP we embrace technology to improve functionality. Our range of products is designed to provide innovative
More informationSynthophone MIDI sax
1 Synthophone MIDI sax Wireless MIDI system - User Guide Introduction The wireless MIDI system is an add-on device for use with the Synthophone MIDI sax. The angled MIDI plug connects to the MIDI socket
More informationSupplemental guide on Camera Fabrication
Supplemental guide on Camera Fabrication This document describes the steps for fabricating your camera and lighting system. 1 Materials needed Gather all your materials. You will need the small lexan sheet
More informationBuilding the Super-VMW CPU Meter by Vincent M. Weaver 18 May 2011
Building the Super-VMW CPU Meter http://www.deater.net/weave/vmwprod/meter/super.html by Vincent M. Weaver 18 May 2011 1 Parts List Part No Description Quantity Source LED Board 1 SVMW-Meter-LED-Board
More informationAXE Stack 18. BASIC-Programmable Microcontroller Kit. An inexpensive introduction to microcontroller technology for all ability levels
Ltd AXE Stack 18 BASIC-Programmable Microcontroller Kit a division of An inexpensive introduction to microcontroller technology for all ability levels Free Windows interface software Programmable in BASIC
More informationHow-To #7: Assemble an H-bridge Circuit Board
How-To #7: Assemble an H-bridge Circuit Board Making a DC motor turn is relatively easy: simply connect the motor's terminals to a power supply. But what if the motor is to be controlled by an Arduino,
More informationBuilding the VMW Time Circuitry Meter by Vincent M. Weaver 6 May 2014
Building the VMW Time Circuitry Meter http://www.deater.net/weave/vmwprod/hardware/time_circuit/ by Vincent M. Weaver 6 May 2014 1 Introduction This is a work in progress. I will update it as I complete
More information2 PIECE BOARD-TO-BOARD
2 PIECE BOARD-TO-BOARD 201-01-123 1. SPECIFICATION DISTRIBUTION No restrictions for issue 2. SCOPE This specification contains the application notes for the 9159 two part connectors. 3. PRODUCTS 10-9159
More informationElement Controller ,-- Installation and set-up Installer manual
Element Controller 062.8610,-- Installation and set-up Installer manual Contents 1 Safety information... 3 2 Description of the element controller (EC)... 3 2.1 Contents of the package and accessories...
More informationGSV-1A4 M12/2 M12/2. Highlights
GSV-1A4 M12/2 M12/2 Highlights Input sensitivity: 2mV/V; 4mV/V, 2 mv/v, 1mV/V, 0.5mV/V configurable via jumpers Output signals ±10V AND 12mA+-8mA on 15 pin Sub-D Integrated half and quarter bridge completion
More information527F CNC. Retrofit controller for machines made by Fadal Machining Centers. Installation and set-up manual Calmotion LLC
527F CNC Retrofit controller for machines made by Fadal Machining Centers Installation and set-up manual 2008-2018 Calmotion LLC Calmotion LLC 7536 San Fernando Road Sun Valley, CA 91352 www.calmotion.com
More informationAdapter Kit - Remote QSI Electronics Installation Instructions
Adapter Kit Remote QSI Electronics Installation Instructions These installation instructions cover the adapter kit installation of the QSI1, QSI2 and QSI3 versions of communications electronics. The instructions
More informationAXi-RGB3 INSTALLATION MANUAL
Rev. 4.0 081915 AXi-RGB3 INSTALLATION MANUAL PLEASE REVIEW THIS INSTALLATION MANUAL CAREFULLY BEFORE BEGINNING ANY WORK COMPATIBLE PLUG & PLAY WIRING HARNESSES AXi-BMW18-R AXi-CRVT-R AXi-FL24-R AXi-GM1-R
More informationGold Drum HV Gold Drum HV Cable Kit (EtherCAT and CAN)
Gold Drum HV Gold Drum HV Cable Kit (EtherCAT and CAN) January 2014 (Ver. 1.000) Notice This guide is delivered subject to the following conditions and restrictions: This guide contains proprietary information
More informationDIN Molded Cable Assemblies
DIN 43650 Telephone (973) 586-500 FAX (973) 596-590 DIN 43650 8mm For Solenoid Valve Applications Black PVC Cable & Connector DUAL JUMPED GROUND PINS Molded cable assemblies can be mounted with cable exiting
More informationCP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split. Document revision 2.1 Last modification : 12/11/17
CP5176 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge
More informationBushBaby DVR: Retrieving Stored Video / Pictures
BushBaby DVR: Retrieving Stored Video / Pictures Page: 1 Types The BushBaby Covert DVR products come either battery powered, or they need to be plugged in. Check the specific product description of the
More informationThe TRSUN is the complete solution for the remote monitoring of photovoltaic plants.
The TRSUN is the complete solution for the remote monitoring of photovoltaic plants. Monitoring of inverters and string combiner boxes (up to 64 devices); Complete configuration of the monitoring system
More informationPickup Gaussmeter v.3.0
Pickup Gaussmeter v.3.0 Features: Range +/- 5600 gauss (with AD22151 sensor) or +/- 1700 Gauss (with A1302 sensor) PCB for main unit and for a double-sensor (A1302-AD22151) double-face probe Normal, peak-hold
More informationMicro USB Lamp Kit ESSENTIAL INFORMATION. Version 2.0 DESIGN A STYLISH LAMP WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS DESIGN A STYLISH LAMP WITH THIS Micro USB Lamp Kit Version 2.0 Build Instructions Before
More informationAccessories Bus Terminals
Accessories s Connectors Lightbus Z1000 Z1010 Z1020 standard connector for 1,000 µm plastic fibre standard connector for 200 µm PCS fibre coupling for Z1000 PROFIBUS ZB3100 ZB3101 ZB3102 ZS1031-3000 ZS1031-3500
More informationBMS: Installation Manual v2.x - Documentation
Page 1 of 7 BMS: Installation Manual v2.x From Documentation This section describes how external peripheral devices are connected and additional functions of the BMS are used. I you have not done so already,
More informationINSTALLATION INSTRUCTIONS
Wired Remote Controller 7 Day Programmable Ductless Systems KSACN0401AAA (High Wall Models) KSACN0501AAA (Ducted/Cassette Models) INSTALLATION INSTRUCTIONS NOTE: Read the entire instruction manual before
More informationFX-2 Control Board ASY-360-XXX Setup and Configuration Guide
FX-2 Control Board ASY-360-XXX Setup and Configuration Guide Micro Air Corporation Phone (609) 259-2636 124 Route 526. WWW.Microair.net Allentown NJ 08501 Fax (609) 259-6601 Table of Contents Introduction...
More informationInstallation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2
1 Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2 Tsubis Part Number: LCD12-0046 Power Down 1. Power down the controller. 2. Power down the complete machine by turning off the rear
More informationCODE 50108, 50110, 50164, 50165
CODE 50108, 50110, 50164, 50165 ASSEMBLY PAGE NAME Machine Assembly Machine Assembly Machine Assembly (Wire feed chamber) Machine Assembly (Wire feed chamber) Feeding Unit Assembly CODE NO.: K NO.: FIGURE
More informationivisibility (Keypad Operator Access Control Series) Lift Truck Onboard Automatic Detection / Recording of All Operational Downtime Events
Installation & Operational Manual ivisibility (Keypad Operator Access Control Series) Lift Truck Onboard Automatic Detection / Recording of All Operational Downtime Events ivisibility V2 General Installation
More informationFibre Modem - Single-mode
Revision 1.0 November. 2006 1 - Single-mode P/N: : 995087 Model 3000 / Access 4000 Optically Isolated Interface INSTALLATION GUIDE OVERVIEW: The Inner Range Single-mode provides 2 separate, optically isolated
More informationPolluTherm. calculator hous. 2 from hous. 1 until X X X X X* X* M-Bus- M-Bus and 2 2PM pulse inputs X X X X
1. Use of the option modules There are two different housings with which these same plug-in units can be used namely: Calculator housing 1 (PolluTherm, PolluStat E and PolluFlow 2010) indicated by a lid
More informationVoomPC-2 Automotive PC Enclosure Mini-ITX Car PC Enclosure. Installation Guide Version 1.0 P/N VOOM-PC-2-ENC. Before you start
VoomPC-2 Automotive PC Enclosure Mini-ITX Car PC Enclosure Installation Guide Version 1.0 P/N VOOM-PC-2-ENC Before you start http://www.cartft.com, Cool Embedded PCs Please take a moment and read this
More informationGEN4 PRO XTREME Initial Setup Instructions for Wireless Ethernet
The GEN4 PRO XTREME Initial Setup Instructions for Wireless Ethernet explain how to; (1) Download the GEN4 PRO XTREME BigComm Pro (BCP) software onto a PC (2) Establish a wireless connection between PC
More informationSection 4 - Automation Assembly
Table of Contents 1. Process Control Unit (PCU) 1.1 Introduction 1.2 PCU Power Cable 1.3 Display and input controls 1.4 Analog Inputs 1.5 FET Outputs 1.6 Thermocouple Connectors 1.7 Table of Thermocouples
More informationHARDWARE OPERATIONS MANUAL
HARDWARE OPERATIONS MANUAL Table of Contents INTRODUCTION... 2 SECTION 1: HARDWARE COMPONENT ASSEMBLIES... 2 MECHANICAL HARDWARE AND CASE... 2 PCB ASSEMBLY... 4 ISD RECORDING CIRCUIT... 5 BREADBOARD ASSEMBLY...
More informationK-Line Milk Car Mini Commander Installation Guide
K-Line Milk Car Mini Commander Installation Guide Revised: October, 2008 OVERVIEW: The Milk car is normally operated by the UCS track, or from the K-Line wireless remote control. When over the UCS track,
More informationInstruction Manual. M Pump Motor Controller. For file reference, please record the following data:
Instruction Manual M Pump Motor Controller For file reference, please record the following data: Model No: Serial No: Installation Date: Installation Location: When ordering replacement parts for your
More informationCeladon, Inc. TRX Series Infrared Remote and Receiver Assembly and Operation Instruction Manual
Celadon, Inc. TRX Series Infrared Remote and Receiver Assembly and Operation Instruction Manual REV 2.1 COPYRIGHT 2001 I. Introduction Thank you for purchasing your infrared remote control transmitter
More informationInstallation Instructions for: Channel Thermocouple Amplifier
Installation Instructions for: 30-2204 4 Channel Thermocouple Amplifier The Advanced Engine Management (AEM) 4 channel thermocouple amplifier revolutionizes temperature measurements by providing laboratory
More informationREMOTE HEAD ADAPTER INSTALLATION GUIDE
REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and
More information