4. We recommend that you install the ievo reader at the DDA height of approximately 1 metre. This will be the perfect height for finger placement.

Size: px

Start display at page:

Download "4. We recommend that you install the ievo reader at the DDA height of approximately 1 metre. This will be the perfect height for finger placement."

Darrell Riley
5 years ago
Views:

2 WELCOME ievo would like to thank you for purchasing our product. This manual is designed to make your installation of our superior biometric reader quick, easy and efficient. Please ensure you check all of the points listed below and read through the manual before commencing your installation. ievo would also recommend making use of the 5 End User guides that are supplied with the reader, which can help train the users of the system to eradicate any finger placement issues. For more End User guides or posters please contact us (Contact details can be found at the back of this manual) 1. Ensure you have selected the correct reader for internal or external use. The external reader is supplied with a built in thermostat controlled heating system. An internal reader, placed externally will not perform to it s required capabilities. 2. If you are fitting a flush mounted reader ensure you have the correct cut out template and have the correct mounting and fixing plates provided in the box. 3. ievo advise the use of a surged protected power supply unit. ievo is designed to shut down as a protection precaution when spikes or noise on line is detected. ievo will reboot straight away after shutdown. The use of a correct power supply will prevent this from taking place. Also, if you are using two power supplies please ensure that they are grounded together. 4. We recommend that you install the ievo reader at the DDA height of approximately 1 metre. This will be the perfect height for finger placement. 5. Ensure you use good quality screened core cables at all times. Only use CAT5 cable for the network connection. NOTE: If you remove the Ferrites to shorten cable length of the reader please replace Ferrites back onto the cable. 6. Each ievo reader needs its own network cable, as each reader has its own IP address. Ensure this has been taken into consideration before commencing with installation. See network pages. 7. Ensure you have calculated the correct power supply amp rating. If you are connecting the ievo board and other controllers/locking mechanisms to the same supply. 8. Please ensure you read all of the information notices in this manual before commencing installation. These are denoted with a yellow triangle. 9. Ensure that the control box is installed on the protected side of the turnstile/door. Do not exceed 5 meters in cable length from the reader to the control box. You are provided with 2.95 meters. Ensure good quality connectors are used if cable is extended. The control box is not IP rated, it can be installed inside the power supply unit. There is a heartbeat LED to show power to the box. The ievo reader button is illuminated blue to show power to the reader. 10. Ensure you read the software set up manual for configuration of each installed reader. 11. ievo has been designed to integrate into other manufacturers controllers and control boards. Our software has also been integrated to ensure a smooth and seamless operation for the end user. We can support you on our software and hardware. We are unable to support you on other manufacturers hardware and software. Please ensure you contact the correct manufacturer if you require assistance. Note: ievo is an independent company and manufacturer of ievo products only. Although ievo has integrated into other manufacturers products with their consent, ievo has no affiliation nor representations of the companies we have integrated into. All companies that we have integrated into have no affiliation or representations of ievo. None of the companies that we have integrated into have endorsed ievo in anyway nor do they have any legal attachment to any claims made by ievo. ievo has no legal attachments to any claims made by the companies we have integrated into. NOTE: ievo is NOT a door relay controller. If you are going to have a high volume of users we recommend purchasing an extra control box for registration. (This is due to the first ievo reader in your list being down when a user is being registered. This will stop the ievo reader working whilst registration is in progress) Warning: When installing the Ievo control box, follow ESD Safety Procedures. Ground yourself to prevent any damage to the electronic components. 1

3 Please read this manual, It will help guide you through installing the ievo reader and software INTRODUCTION: This Manual will cover the following areas in detail: Installation Support The minimum specs for your PC should be: CPU: Hard Drive: Memory: Dual Core 2.0+ GHz (or equivalent) 10 GB 2 GB Integrated Software: Net2 V4.19 / ACT Lite v2.8 32bit only Network: NIC (Static IP) Microsoft.NET : Version 3.5 or greater. OS: Windows XP SP3, Vista, Windows 7. (32bit / 64bit) To get the best performance from our software, please make sure your PC meets our minimum specification. Please be aware malware and viruses on the pc may also effect our software. 2

4 CONTENTS: Page1: Page2: Page3: Page4: Page5: Page6: Page7: Page8: Page9: Page10: Page11: Page12: Page13: Page14: Page15: Page16: Page17: Welcome Introduction Contents INSTALLATION Assembly Surface mount Flush mount Wiring Diagram Turnstile Example ievo Wiring Example Network Wiegand Diagram (Paxton Net2) Wiegand Diagram (ACT) Installing ievo software Installing USB Drivers Installing USB Drivers2 SUPPORT 3

5 4

Do not remove any of the security labels as this will void all warranties For mounting through wall For conduit mounting Remove back plate screws

6 Ensure you are installing the correct reader for internal or external use Do not exceed 5 meters in cable length from the reader to the ievo control board. You are provided with 2.95 meters. Ensure good quality connectors if cable is extended. Do not remove any of the security labels as this will void all warranties For mounting through wall For conduit mounting Remove back plate screws and back plate. Position the two cables into the duct as shown below. Reattach the mounting plate and screws Do not remove the screws indicated with the green arrows. This will void your warranty. 5

SURFACE MOUNTED INSTALLATION The reader should be placed within the DDA standard height of approximately 1

Incorrect usage will result in the reader being unsecure.

1 2 Use wall mounting plate to mark out size of hole needed on the wall for the cables of the reader.

attach reader to back plate by clipping on and sliding down until it is locked into position When reader is

7 SURFACE MOUNTED INSTALLATION The reader should be placed within the DDA standard height of approximately 1 meter Ensure you use the correct fixing plug for the type of wall you are fixing the reader to. Incorrect usage will result in the reader being unsecure. Plaster board will require correct brackets for installation. 1 2 Use wall mounting plate to mark out size of hole needed on the wall for the cables of the reader. Screw back plate to wall ensuring use of correct screws and fixings 3 4 Feed cables through hole and then attach reader to back plate by clipping on and sliding down until it is locked into position When reader is fixed onto the wall plate use the small security screw provided to connect the wall plate and reader back plate. Now bend upwards the security cover latch on the wall plate as indicated with the green and red arrows. 6

FLUSH MOUNTED INSTALLATION NOTE: The reader should be placed within the DDA standard height of

using the six (6) screws provided. Do not over tighten the screws.

provided into the wall as shown in the diagram. Ensure you use the security tool provided.

8 FLUSH MOUNTED INSTALLATION NOTE: The reader should be placed within the DDA standard height of approximately 1 meter Attach the reader back plate and the flush mounting plate to the back of the reader using the six (6) screws provided. Do not over tighten the screws. Ensure both cables are fed through the holes as shown in green Insert the four (4) security screws provided into the wall as shown in the diagram. Ensure you use the security tool provided. Ensure you use the correct fixing plug for the type of wall you are fixing the reader to. Incorrect usage will result in the reader being unsecure. Plaster board will require correct brackets for installation. Insert the facia cover over the reader. Ensure the facia is the correct way up as denoted by the arrows on the internal of the facia. The facia will snap and lock into place 7

9 WIRING DIAGRAM If you are experiencing connection problems please ensure cables are sitting in the connectors correctly. When doing this ensure you use the correct size flat head screwdriver. ievo BOARD Cat 5 Network connection 1 GND ) From PSU 2. 12v )Ground to earth 3. +5V ) 4. Blue LED ) 5. Heater (12V) ) 6. Granted LED ) Cable from 7. Denied LED ) ievo 8. Buzzer ) reader 9. Trigger Input ) 10. GND ) 11. Data / D0 ) Cable to 12. Clock / D1 ) Controller 13. GND ) See weigand 14. GND ) 15. D1 ) Cable from 16. D0 ) ievo V ) reader 18. Network ) Cable to PC Power Buzzer / LED / Button / Heat system Wiegand Output USB Warning: When installing the ievo control box, follow ESD Safety Procedures. Ground yourself to prevent damage to the any electronic component. 8

10 TURNSTILE Router 2amp PSU Network hub ievo net2 net2 2amp PSU ievo OUT IN KEY: ievo ievo cable Relay Wiegand TCP/IP RS485 12vdc Ievo controller is NOT IP rated. Please secure inside an IP65 secure box. 9

11 IEVO WIRING Network Hub 12v/ 2amp PSU ievo ACU Cable: KEY: ievo Connections: Power (2 core) Buzzer / LED / Button / Heat system (8 core) USB (4 core) Wiegand (3 core) PC/ Laptop ievo CAT5 (Network cable) IEvo controller is NOT IP rated. Please secure inside an IP65 secure box. Please refer to manufacturer ACU manual for correct installation of ACU board. ievo and ACU must be installed internally 10

12 NETWORK EXAMPLE Front Door Port: 5005 Office Door Port: 5005 Office in England Side Door Port 5005 Network Network Router ievo Software WAN IP: Anywhere in the world Front IN Port: 5005 Front OUT Port: 5006 Stock Room Port:

KEY: ievo Data/D0 Clock/D1 Gnd Paxton Data/D0 Clock/D1 Gnd Please use Belden 9534 (4

13 WIEGAND DIAGRAM FOR PAXTON NET2 ievo BOARD Net2 Classic/Plus/ Nano Controller You can connect ievo into reader 1 or reader 2 port. KEY: ievo Data/D0 Clock/D1 Gnd Paxton Data/D0 Clock/D1 Gnd Please use Belden 9534 (4 Core shielded) twist 2 pairs for clock and data and use shield for GND for long cable runs. MAXIMUM DISTANCE UPTO 100 METERS 12

(4 Core shielded) twist 2 pairs for clock and data and use shield for GND

14 WIEGAND DIAGRAM FOR ACT ievo BOARD ACT-1000/2000/3200 Door Controller KEY: ievo Data/D0 Clock/D1 Gnd Act Data Clock 0v Please use Belden 9534 (4 Core shielded) twist 2 pairs for clock and data and use shield for GND for long cable runs. RS Part number: MAXIMUM DISTANCE UPTO 100 METERS 13

15 INSTALLING IEVO SOFTWARE Please first insert the ievo disk into your computer Click Run setup.exe Click accept and then Next Click Next Click Next Click Install ievo will now be installed. To open the software please go to your desktop. NOTE: To use ievo you must first install your Third party software...unless you are running ievo Standalone version. Click Finish 14

16 INSTALLING USB DRIVERS Please first insert the ievo disk into your computer Please run usb drivers.exe 15

17 Please follow these steps Click Next Tick Accept and then Next Choose which operating system you are running and click Next Click Install Installation is now complete, now click Finish 16

18 Support HELP AND SUPPORT ievo Contact support: Tel: Web: Help & Support: For Support please click Menu on the user list and click Help & Support ievo address: Address: ievo Ltd. Henson House, George Stephenson Ind. Est, Newcastle upon Tyne, NE12 6RZ 17

WELCOME. Network: Only use Shielded CAT5 cable for network communication.

WELCOME. Network: Only use Shielded CAT5 cable for network communication. WELCOME ievo would like to thank you for purchasing our product. This manual is designed to make your installation of our superior biometric reader quick, easy and efficient. Please ensure you check all