TB-FMCH-TYPER Hardware User Manual TB-FMCH-TYPER. Hardware User Manual Rev.2.01

Transcription

1 TB-FMCH-TYPER Hardware User Manual 1

2 Revision History Version Date Description Publisher Rev Preliminary Nagatani Rev Changes to the Sht.7 FMC(HPC) drawing Nagatani Rev Changes point is related to PCB design change. Nagatani Rev Release version. Yoshioka Add notice for Type-R connector Yoshioka 2

3 Table of Contents 1. Related Documents and Board Accessories Overview Features Block Diagram External View of the Board Board Specification Description of Each Component Signal connections between TypeR and FMC connectors Signal Connections between Pin Header and TypeR/FMC Connectors Power Supply Connector FMC Connector Signal Processing Test Points (TPs) Signal Ground Appendix Example connection to TB-6S-150T-IMG(Platform board)...15 List of Figures Figure 3-1 FMC Connector Pin Layouts... 7 Figure 4-1 Block Diagram... 8 Figure 5-1 Component Side... 9 Figure5-2 Solder Side... 9 Figure6-1 Board Dimensions (inclusive of a wasteable portion) Figure7-1 Power Supply Connectors Figure7-2 FMC CN Signal Ground Structure Figure8-1 External View and Dimensions Figure8-2 Signal Wiring Diagram Figure 9-1 Connect to TB-6S-150T-IMG(Platform board) List of Tables Table 1 TypeR CN(CN2) Signal Connections...11 Table 2 TypeR CN(CN3) Signal Connections...11 Table 3 Connection with the Pin Header Table 4 FMC CN Signal Test Pads Table 5 FMC CN Signal Ground

4 Introduction Thank you for purchasing the TB-FMCH-TYPER board. Before using the product, be sure to carefully read this User Manual and fully understand how to correctly use the product. Read through this manual and always keep it handy. Safety Precautions Be sure to observe these precautions Observe the precautions listed below to prevent injuries to you or other personnel or damage to property. Before using the product, read these safety precautions carefully to assure correct use. These precautions contain serious safety instructions that must be observed. After reading through this manual, be sure to always keep it handy. The following conventions are used to indicate and classify precautions in this manual. Failure to observe precautions can result in injury to people or damage to property. Danger Indicates the high possibility of serious injury or death if the product is handled incorrectly. Warning Indicates the possibility of serious injury or death if the product is handled incorrectly. Caution Indicates the possibility of injury or physical damage in connection with houses or household goods if the product is handled incorrectly. The following graphical symbols are used to indicate and classify precautions in this manual. (Examples) Be sure to turn off the power switch. Do not disassemble the product. Do not attempt this. 4

5 Warning In the event of a failure, disconnect the power supply. If the product is used as is, a fire or electric shock may occur. Disconnect the power supply immediately and contact our sales personnel for repair. If an unpleasant smell or smoking occurs, disconnect the power supply. If the product is used as is, a fire or electric shock may occur. Disconnect the power supply immediately. After verifying that no smoking is observed, contact our sales personnel for repair. Do not disassemble, repair or modify the product. Otherwise, a fire or electric shock may occur due to a short circuit or heat generation. For inspection, modification or repair, contact our sales personnel. Do not touch a cooling fan (when installing it). As a cooling fan rotates in high speed, do not put your hand close to it. Otherwise, it may cause injury to persons. Never touch a rotating cooling fan. Do not place the product on unstable locations. Otherwise, it may drop or fall, resulting in injury to persons or failure. If the product is dropped or damaged, do not use it as is. Otherwise, a fire or electric shock may occur. Do not touch the product with a metallic object. Otherwise, a fire or electric shock may occur. Do not place the product in dusty or humid locations or where water may splash. Otherwise, a fire or electric shock may occur. Do not get the product wet or touch it with a wet hand. Otherwise, the product may break down or it may cause a fire, smoking or electric shock. Do not touch a connector (gold-plated portion) on the product. Otherwise, the surface of a connector may be contaminated with sweat or skin oil, resulting in contact failure of a connector or it may cause a malfunction, fire or electric shock due to static electricity. 5

6 Caution Do not use or place the product in the following locations. Humid and dusty locations Airless locations such as closet or bookshelf Locations which receive oily smoke or steam Locations exposed to direct sunlight Locations close to heating equipment Closed inside of a car where the temperature becomes high Staticky locations Locations close to water or chemicals Otherwise, a fire, electric shock, accident or deformation may occur due to a short circuit or heat generation. Do not place heavy things on the product. Otherwise, the product may be damaged. Disclaimer This product is a board intended for conversion between the Samtec FMC connector and the Samtec QSE-DP series connector and can achieve gigabit transfer speeds. Tokyo Electron Device Limited assumes no responsibility for any damages resulting from the use of this product for purposes other than those stated. Even if the product is used properly, Tokyo Electron Device Limited assumes no responsibility for any damages caused by: - Earthquake, thunder, natural disaster or fire resulting from the use beyond our responsibility, acts by a third party or other accidents, the customer s willful or accidental misuse or use under other abnormal conditions, - Secondary impact arising from use of this product or its unusable state (business interruption or others), - Use of this product against the instructions given in this manual or - Malfunctions due to connection to other devices. Tokyo Electron Device Limited assumes no responsibility or liability for: - Erasure or corruption of data arising from use of this product - Any consequences or other abnormalities arising from use of this product, or - Damage of this product not due to our responsibility or failure due to modification This product has been developed by assuming its use for research, testing or evaluation. It is not authorized for use in any system or application that requires high reliability. Repair of this product is carried out by replacing it on a chargeable basis, not repairing the faulty devices. However, non-chargeable replacement is offered for initial failure if such notification is received within two weeks after delivery of the product. The specification of this product is subject to change without prior notice. The product is subject to discontinuation without prior notice. 6

7 1. Related Documents and Board Accessories Related documents: All documents relating to this board can be downloaded from our website. Please see attached paper on the products. Board Accessories: - FMC spacer set M2.6 X 10 spacer (Duracon): 2 Screws with Duracon washer: 4 - QSE spacer set M2.6 X 10 spacer (Duracon): 2 Screws with Duracon washer: 4 - Loopback test board 2. Overview This board is intended to be used for conversion between Samtec FMC and Samtec QSE-DP Series connectors. The board can achieve gigabit transfer speeds. The board has been designed for connection with high-pin-count platform boards. 3. Features FMC Connector: Samtec FMC Connector (High-Pin Count) TypeR Connector: Samtec QSE-DP Series General-Purpose Interface: General-purpose 2.54 mm pitch Pin Header Figure 3-1 FMC Connector Pin Layouts 7

8 4. Block Diagram Figure 4-1 shows a block diagram of the TB-FMCH-TYPER board. The FMC connector is mounted on the solder side of the board. Figure 4-1 Block Diagram Main Functions: 1. Two signal paths (4 CH for each TX and RX), one via the FMC connector and the other via the TypeR connector 2. Provide power to the TypeR connector (Power CN) 3. General-purpose interface (Pin Header) Notice Type-R connector of this board is not same pin assignment as other boards. Please see following notice. 1) This board can not connect with TB-OP-SFP board. 2) Please confirm the cable pin assignment when using with TB-5V-xx-PCIEXP or TB-5V-xx-PCI-EX. 8

9 5. External View of the Board Figures 5-1 and 5-2 show external views of the board. Figure 5-1 Component Side Figure5-2 Solder Side 9

10 TB-FMCH-TYPER Hardware User Manual 6. Board Specification External Dimensions: 78.8 mm (W) x 69 mm (H) Layer Structure: 8-Layer Board Thickness: 1.6 mm Material: FR-4 FMC Connector: Samtec ASP TypeR Connector: Samtec QSE-014-D1-L-D-DP-A Figure6-1 Board Dimensions (inclusive of a wasteable portion) 10

11 7. Description of Each Component 7.1. Signal connections between TypeR and FMC connectors Table 1 shows signal connections between TypeR and FMC connectors. The TypeR connector provides two signal lines, CN2 and CN3, each for 4CH TX and 4CH RX and 4 pair signal connections. Table 1 TypeR CN(CN2) Signal Connections FMC FMC Signal Name TypeR CN(CN2) Signal Name Pin No. Pin No. C6 DP0_M2C_P 1 2 DP0_C2M_P C2 C7 DP0_M2C_N 3 4 DP0_C2M_N C3 A3 DP1_M2C_N 7 8 DP1_C2M_N A23 A2 DP1_M2C_P 9 10 DP1_C2M_P A22 A6 DP2_M2C_P DP2_C2M_P A26 A7 DP2_M2C_N DP2_C2M_N A27 A11 DP3_M2C_N DP3_C2M_N A31 A10 DP3_M2C_P DP3_C2M_P A30 - GND 5,11,17,23 6,12,18,24 25,27,29,35 26,28,30,36 GND ,33,37,39 32,34,38,40 - * Used for signal connections with Pin Header (CN4). For details, see Signal Connections between Pin Header and TypeR/FMC Connectors in Section 7.2 Table 2 TypeR CN(CN3) Signal Connections FMC FMC Signal Name TypeR CN(CN3) Signal Name Pin No. Pin No. A14 DP4_M2C_P 1 2 DP4_C2M_P A34 A15 DP4_M2C_N 3 4 DP4_C2M_N A35 A19 DP5_M2C_N 7 8 DP5_C2M_N A39 A18 DP5_M2C_P 9 10 DP5_C2M_P A38 B16 DP6_M2C_P DP6_C2M_P B36 B17 DP6_M2C_N DP6_C2M_N B37 B13 DP7_M2C_N DP7_C2M_N B33 B12 DP7_M2C_P DP7_C2M_P B32 - GND 5,11,17,23 6,12,18,24 25,27,29,35 26,28,30,36 GND ,33,37,39 32,34,38,40 - * Used for signal connections with Pin Header (CN4). For details, see Signal Connections between Pin Header and TypeR/FMC Connectors in Section

12 7.2. Signal Connections between Pin Header and TypeR/FMC Connectors The Pin Header is a 34 pin connector. Of these pins, 32 are used for signals. The Pin Header is connected with each TypeR connector via a 4-pair cable and with the FMC connector via an 8-pair cable. Table 3 shows the pin connections with the FMC connector. Table 3 Connection with the Pin Header FMC(Cn1) PinHeader(CN4) TypeR Pin No. Signal Pin No. Pin No. CN No. Pin No. C10 LA06_P 1 2 CN3 40 C11 LA06_N 3 4 CN3 38 C14 LA10_P 5 6 CN3 34 C15 LA10_N 7 8 CN3 32 C18 LA14_P 9 10 CN3 31 C19 LA14_N CN3 33 D8 LA01_P_CC CN3 37 D9 LA01_N_CC CN3 39 D11 LA05_P CN2 40 D12 LA05_N CN2 38 D14 LA09_P CN2 34 D15 LA09_N CN2 32 D17 LA13_P CN2 31 D18 LA13_N CN2 33 G6 LA00_P_CC CN2 37 G7 LA00_N_CC CN2 39 GND GND 7.3. Power Supply Connector The board has Samtec power supply connectors (CN5/CN6) to provide power to external devices. This power can be either 12 V or 3.3 V which is supplied via the FMC connector. The power supply connector can be mounted either at CN5 (component side) or CN6 (solder side). At shipment it is mounted at CN5. Figure7-1 Power Supply Connectors 12

13 7.4. FMC Connector Signal Processing The following signal processing is performed for the FMC connector pins Test Points (TPs) The board provides on-board test pads (TPs) to monitor the FMC connector pin signals. Table 4 FMC CN Signal Test Pads FMC Pin No. Pin No. Pin Name Test PAD C34 GA0 TP2 D35 GA1 TP1 H1 VREF_A_M2C TP3 K1 VREF_B_M2C TP Signal Ground The following signal ground structures can be implemented for the FMC connector pins. The resistors are not mounted at shipment. Figure7-2 FMC CN Signal Ground Structure Table 5 FMC CN Signal Ground FMC Pin No. Pin No. Pin Name Resistor D1 PG_C2M R1 F1 PG_M2C R2 H2 PRSNT_M2C_L R3 13

14 TB-FMCH-TYPER Hardware User Manual 8. Appendix The board comes with a loopback board for the TypeR connector. performed by connecting this board to the TB-FMCH-TYPER. A signal loopback test can be Figure 8-1 shows external view and dimensions. Figure8-1 External View and Dimensions The board provides the following two structures (the figure shows only one). Figure8-2 Signal Wiring Diagram 14

15 9. Example connection to TB-6S-150T-IMG(Platform board) Figure 9-1 Connect to TB-6S-150T-IMG(Platform board) 15

16 PLD Solution Division URL: HEAD Quarter : Yokohama East Square, 1-4 Kinko-cho, Kanagawa-ku, Yokohama City, Kanagawa, Japan TEL: FAX: