Integrating and configuring Dynalite lighting and heating systems with SystemNet software
|
|
- Doreen Owens
- 5 years ago
- Views:
Transcription
1 Integrating and configuring Dynalite lighting and heating systems with SystemNet software System Net Configuration Software 10.0 or higher Firmware 10.0 or higher S6 or six port hub only, colour touch screens only 17 th December 2008 Paul Hilditch Introduction Dynalite manufacturer sophisticated lighting and heating control systems often used in the residential market. Systemline colour touch screens have lighting and heating control options, and with version 10.0 or above also have the RS232 serial driver software to operate the Dynalite system. Using this release it will be possible to operate the following functions via a Dynalite system using an RS232 link to Systemline: 1. Lighting Scenes 2. Lighting Off 3. Raise or Lower lighting manually 4. Curtain Open or Close 5. Gate Open or Close 6. Display current temperature of a zone 7. Change state of heating between Comfort, Standby, Night or Frost Protection 8. Display temperature set point in a zone on all states 9. Adjust set point in Comfort mode. Each touch screen s Dynalite settings can be configured independently, so lighting and heating can be controlled on a zone by zone basis. Up to 8 touch screens can be used in a Systemline system, one in each zone. You can mix local zone control and global house control of lighting on each touch screen.
2 Connections A Dynalite DNG232 must be used to create the RS232 interface required by SystemNet. The DNG232 plugs into the four-wire Dynalite power and data bus like any other Dynalite device. It is better placed as close to Systemline S6 or System Net Hub as possible to keep the RS232 cable as short as possible. You should use a straight through male to female serial RS232 cable to connect the DNG232 to SystemNet. The DNG232 unit must be setup to accept and communicate ASCII text commands. DNG232 Port configuration For the DNG232 to communicate with the Systemline system, port 2 must be configured as a Text Gateway (Default setting). In DLight 2 under the Utils menu list, select Serial Port Settings > Port 2 Settings. Ensure that the Protocol is set to Text Gateway. Use one of the six serial ports available on SystemNet for the RS232 cable. Software configuration You must use 10.0 or higher System Net software and firmware to use the Dynalite interface as well as S6 or six port modular System Net Hubs. You must also use colour touch screen keypads as monochrome keypads are not able to use this control method. Two port hubs cannot be used for this application. Firstly you must add Dynalite as a configurable source; you can then select this and press Configure. This opens up a new window with the serial port you wish to use. Select the desired serial port that you have plugged the DNG232 box into, this is a drop down option from one to six.
3 You can proceed adding any other serial devices you wish to use and configure the six audio inputs for Systemline. You must then add up to 8 keypads in your system (1 per zone), only colour keypads will allow you to configure Dynalite lighting or heating. Lighting Control You can select Dynalite lighting for each keypad that requires lighting control from the drop down Lighting section. You can then configure up to 16 lighting or automation buttons (8 per page) for each keypad by selecting the Configure button in the lighting section. You can select a graphic image for each button by using the Button Icon drop down option; this then allows you to configure the Dynalite settings for each button. It is
4 possible to configure a button to toggle between two presets by selecting the toggle tick box; otherwise the button will always have one preset function. Each button must have an area number defined. This refers to the area location in the Dynalite system, and will operate lighting circuits configured in your selected area. An area address can have a value from 0 to 255. You can then select the preset value you wish the button to use, the functionality of the preset is determined in the Dynalite system. Presets have a value from 0 to 255. Lighting scenes need a fade time which is configured in the fade time window, values are in milliseconds. 1000=1 second. There is no configuration setting for raise or lower lighting other than the area address, as this is a fixed function. Finally you can input a label for each button such as Scene 1 or TV etc. describing the function of each button. The example above shows 7 buttons configured for page one of a keypad with four scenes, off, raise and lower.
5 The example above shows two sets of motorized curtain with each button acting as a toggle, allowing a curtain to open or close or stop if pressed again. Heating Control You can select Dynalite heating for any colour touch screen in your system. The Dynalite system must contain appropriate equipment to control the heating system such as temperature sensors and mains relays. The Dynalite software must also be configured to monitor actual temperate against set point temperature and switch on any floor heating/boilers etc as needed. Systemline does not operate a time clock function, so automatic set point modes throughout the day must be setup in the Dynalite software. Systemline allows day to day adjustment of comfort set point temperature, and zone mode. The temperature configuration in SystemNet simply allows you to configure the area number for adjustment and monitoring. You will need to know the Dynalite actual temperate and set point temperature area addresses for this.
6 There are four room modes available, each activated by a specific preset command in the correct area. Comfort Standby Night Frost Preset One Preset Two Preset Three Preset Four The Dynalite system should have a set point configured for each of these presets; Systemline will show these and then allow adjustment of Comfort only. Possible problems Problem Lights do not switch on when a scene is Selected. There is no actual temperature displayed Suggested Solution Check area address or preset value Make sure DNG232 is set for text commands Make sure area address is set correctly for both Dynalite temperature sensor END
application software
application software application software RF input product Electrical / Mechanical characteristics: see product user manual Product reference Product designation TP device RF devices 8565 52 xx 8565 62
More informationThe Lumina has an astronomical clock and automatically adjusts for daylight savings time in order to provide accurate dusk to dawn lighting control.
Lumina Technical Sheet Now includes flash memory for easy firmware updates and five serial ports. DESCRIPTION The Lumina is a central lighting and automation controller. Lumina provides elegance and convenience
More informationSmart Touch Thermostat Colour Touchscreen Thermostat
OBSMART Smart Touch Thermostat Colour Touchscreen Thermostat INTRODUCTION Orbry Smart Touch Thermostat The Orbry Smart Touch Thermostat is a digital thermostat, which is designed for electric underfloor
More informationIn the following learning unit, you will simulate parameterising the heating function in the ETS.
Introduction Introduction: Heating control plays an important role in building technology. The most energy is consumed in heating buildings. With intelligent control, the effort is reduced while the level
More informationA suggested source is Opternus:
Manufacturer: KNX Input / Output Integration Note Model Number(s): (Various) Core Module Version: g! Core Module 5.4 or newer Document Revision Date: 1/9/2013 OVERVIEW AND SUPPORTED FEATURES KNX systems
More informationControl-Specification-V4.2.pdf
Clipsal C-Bus Control of Systemline 7 Rev 1.0 23 rd May 2018 1.0 Introduction The Schneider Electric C-Bus Network Automation Controller allows a C-bus system to control S7 using a network connection.
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES
Manufacturer: Model Number(s): KNX Climate (Various) Minimum Core Module g! 5.4 Version: g! 6.2 Minimum for Fan Coil Climate Modes Document Revision Date: 10/8/2015 OVERVIEW AND SUPPORTED FEATURES Integration
More informationHTM F. General Description. Features
Controls by Monodraught HTM F General Description The Smart Screen Controller is a high quality interface that provides a graphical insight into the operation of Monodraught ventilation systems. Through
More informationColour Touch Panel 3.5
Guangzhou Video-star Electronics Industrial Co., Ltd K-BUS R Colour Touch Panel 3.5 User manual-ver. 1.2 CHTF-35/01.1 CHTF-35/01.2.21 CHTF-35/01.2.22 CHTF-35/01.2.24 KNX/EIB Intelligent Installation Systems
More informationGRAFIK Eye QS Wireless
Open Preset Close Meeting Video Conference A/V Off GRAFIK Eye QS Wireless Customisable preset light, blind, and energy control Photography Nic Lehoux What is GRAFIK Eye QS Wireless? GRAFIK Eye QS Wireless
More informationOEM. Room unit QAA822 with2- wire interface. Building Technologies CLIMATIX TM. For use with Climatix controllers
OEM CLIMATIX TM Room unit QAA822 with2- wire interface For use with Climatix controllers Remote control of air conditioning unit Mandík Measurement of the room temperature Buttons for starting, setting
More informationTebis application software
5 Tebis application software SXB322AU V 1.x 2 inputs / 2-output module LED SXB344AU V 1.x 4 inputs / 4-output module LED Product reference Product designation TXB322AU TXB344AU Embedded module: 2 inputs
More informationLumina Version 2.15 Firmware Release
Lumina Version 2.15 Firmware Release ADD THIS DOCUMENT TO YOUR LUMINA ADVANCED APPLICATION GUIDE Description The Lumina Version 2.15 firmware adds the following new features: Support for DSC Power Series
More informationUCU Room Display. Operation Modes. Features. Applications DATASHEET
DATASHEET UCU Room Display The UCU Room Display provides dedicated visually appealing Room Control display for use with UCU10FC/K Unitary Controller. The display allows the user to view and adjust selected
More informationModel: Touchpad (TFT) Model: TFT
Model: Touchpad (TFT) Model: TFT 1 Model: Touchpad TFT Table of Contents Set-Up Product Image Table of Contents Installation Procedure Initial Setup Setting the Clock LCD Display My System Locking the
More informationIntegration Note. Virtual Matrix: The driver offers the ability to receive the auxiliary input feed from up to three other Sonos units
Integration Note Manufacturer: Sonos Model Number(s): Sonos PLAYBAR up to ver. 7.1 g! Core Module Version: 8.0.278 Driver Developer: Core Programming Limited Document Revision Date: 03/01/2017 OVERVIEW
More informationiridium for HDL-BUS Pro
iridium for HDL-BUS Pro Fast Start: Connection Setting Manual for HDL-BUS Pro (Smart-Bus) equipment Review of iridium Software Package for HDL-BUS Pro: The iridium software package includes several components
More informationContent 1. Important. Please take notice of these important remarks prior to further reading!
illus user manual Content Content 1 User zones 2 Stanby button 3 Configuration button 3 Rooms button 4 Device zone 5 Control zone 6 Specials 7 sensors 7 regimes 8 audio 8 intercom 8 Important Please take
More informationliving connect and Danfoss Link CC wireless thermostat system. Total temperature control from one central point.
MAKING MODERN LIVING POSSIBLE living connect and Danfoss Link CC wireless thermostat system. Total temperature control from one central point. living connect and Danfoss Link CC for total wireless control,
More informationService Pack3 Handbook
Service Pack3 Handbook WHAT S NEW IN SERVICE PACK 3 Version 09/11 1 INDEX 1 INTRODUCTION...3 2 SERVICE PACK 3 DESCRIPTION...4 2.1 CONFIGURATION TOOL...4 2.1.1 Time and date updating via Internet...4 2.1.2
More informationliving connect and Danfoss Link CC wireless thermostat system. Total temperature control from one central point.
MAKING MODERN LIVING POSSIBLE living connect and Danfoss Link CC wireless thermostat system. Total temperature control from one central point. living connect and Danfoss Link CC for total wireless control,
More informationContent 1. Important. Please take notice of these important remarks prior to further reading!
illus user manual Content Content 1 User zones 2 Stanby button 3 Configuration button 3 Rooms button 4 Device zone 5 Control zone 6 Specials 7 sensors 7 regimes 8 audio 8 intercom 8 Important Please take
More informationFANCOIL CONTROLLER UNIT TC17B01KNX. Product Handbook
FANCOIL CONTROLLER UNIT TC17B01KNX Product Handbook Product: TC17B01KNX Description: FANCOIL CONTROLLER UNIT Document Version: 1.2 Date: 09/09/2016 1/37 INDEX 1. General Introduction... 4 2. Product and
More informationWireless Touchscreen Installation Guide
Wireless Touchscreen Installation Guide Safety Declaration of Conformity The Systemline Wireless Commander has been designed and independently tested to be in compliance with the following standards:
More information13 x13 Modular. LED Dance Floor. General Description: Specification:
General Description: features a built in touch pressure sensor. Each dance floor piece can ran separately or combined with WDM Dance Floor Controller the color brightness, color changing speeds, and sensitivity
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES. Model Number(s): (Various)
Integration Note Manufacturer: KNX Lighting Model Number(s): (Various) Minimum Core Module Version: 5.4 Document Revision Date: 2/11/2013 OVERVIEW AND SUPPORTED FEATURES KNX lighting systems are designed
More informationKNX/EIB Intelligent Installation Systems
K-BUS R Shutter Actuator, 4fold User manual-ver. 1 AWBS-04/00.1 KNX/EIB Intelligent Installation Systems Conents 1. General ---------------------------------------------------------------------------------------------------------------------
More informationIntroduction of Configure Software for 3.5'' Touch Panel
Introduction of Configure Software for 3.5'' Touch Panel 1. Brief Introduction This Configure Software is used with the 3.5'' Touch Panel. After setting group address of different devices in ETS users
More informationGlass sensors 35. Supplementary products 39
Understatement is an art, and the makes it perfect. Up to eight functions are concealed under a pure surface that is practically flush with the wall, and can be custom-labelled on request. A single touch
More informationModel: Available in : Sapphire Black and Glacier White
1 Model: Available in : Sapphire Black and Glacier White 1 Table of Contents Product Image 1 Locking/Unlocking the SmartStat 20 23 Table of Contents 2 Standby/Away Mode Mode 21 24 What is a Programmable
More informationSophisticated yet simple energy-efficient lighting solutions
Lighting Sophisticated yet simple energy-efficient lighting solutions Dynalite System Integration Within any modern project, many third-party systems can be found performing different roles. Each separate
More informationLumina Pro Version 2.15 Firmware Release
Lumina Pro Version 2.15 Firmware Release ADD THIS DOCUMENT TO YOUR LUMINA PRO ADVANCED APPLICATION GUIDE Description The Lumina Pro Version 2.15 firmware adds the following new features: Support for DSC
More informationTemperature control unit
Temperature control unit 5739 18/19 Installation manual Part. U3582A - 12/08-01 PC Contents 1 - Introduction 5 1.1 - Warnings and tips 5 1.2 - Contents of package 5 2 - Description of the Control unit
More informationApplication description. Motion detector KNX- BCU
Application description Motion detector KNX-BCU Electrical/mechanical data: see the operating instructions for the product Order number Product designation Application programme TP product Radio product
More informationApplication description. KNX push-button 1gang. KNX push-button 2gang. KNX push-button 3gang. KNX push-button 4gang. Page 1/51
Application description KNX push-button 1, 2, 3 and 4gang Electrical/mechanical data: see the operating instructions for the product Order number Product designation Application programme TP product Radio
More informationHLS34 Modbus FCU/VAV Controllers installation instructions
HLS34 Modbus FCU/VAV Controllers installation instructions The HLS34 is specifically designed for individual room temperature and zone control applications. The controllers have built-in RS-485 channel
More informationUSER MANUAL. RC-43SL 6-Button Room Controller MODEL: P/N: Rev 1.
USER MANUAL MODEL: RC-43SL 6-Button Room Controller P/N: 2900-300450 Rev 1 www.kramerav.com Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions
More informationDS Type: MAXIM III Controller
DS 10.03 Models: MAX3ELD MAX3ELN MAX3NLD MAX3NLN Overview The Innotech MAXIM III Controller is a state of the art digital processing system that has the capability of controlling various types of industrial,
More informationIntegration Note. Manufacturer: OVERVIEW AND SUPPORTED FEATURES. Model Number(s): DSC POWER SERIES / IT-100
Manufacturer: DSC Integration Note Model Number(s): DSC POWER SERIES / IT-100 Core Module Version: 6.4.209 Comments: Document Revision Date: 9/11/2013 OVERVIEW AND SUPPORTED FEATURES The DSC Power Series
More informationModel: Available in : Sapphire Black and Glacier White
Model: Available in : Sapphire Black and Glacier White 1 Table of Contents Product Image 1 Locking/Unlocking the SmartStat 20 Table of Contents 2 Standby/Away Mode 21 What is a Programmable Room Thermostat?
More informationIntegration Note. Manufacturer: OVERVIEW AND SUPPORTED FEATURES. Model Number(s): Power Series / 5401
Manufacturer: DSC Integration Note Model Number(s): Power Series / 5401 Core Module Version: 4.0 (all builds) Comments: Document Revision Date: 1/30/2013 OVERVIEW AND SUPPORTED FEATURES The DSC Power Series
More informationK-BUS Shutter Actuator. User manual-ver. 1
Guangzhou Video-Star Eletronnics Co.,Ltd. K-BUS Shutter Actuator User manual-ver. 1 AWBS-04/00.1 Intelligent Installation Systems http://www.video-star.com.cn Conents 1. General ---------------------------------------------------------------------------------------------------------------------
More informationWelcome. Getting Started.
S7 Homeowners Guide Welcome. Congratulations. Your home has been pre-fitted with the very latest, installed multi-room audio entertainment system from Systemline. This means you can enjoy the highest quality
More informationUSER MANUAL. RC-43SL 6-Button Room Controller MODEL: P/N: Rev 3.
USER MANUAL MODEL: RC-43SL 6-Button Room Controller P/N: 2900-300450 Rev 3 www.kramerav.com Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions
More informationABB STOTZ-KONTAKT GmbH. ABB i-bus KNX Room Master, Basic, RM/S 1.1
ABB STOTZ-KONTAKT GmbH ABB i-bus KNX Room Master, Basic, RM/S 1.1 2CDC 514 052 N0201 Slide 1 New Innovation Room Master Innovation features Room Scenarios Recall with one group-address All function in
More informationDeseo KNX Manual. Deseo KNX. Manual. basalte bvba hundelgemsesteenweg 1a 9820 merelbeke belgium. 1 / 65 v basalte
Deseo KNX basalte bvba hundelgemsesteenweg 1a 9820 merelbeke belgium 1 / 65 v2.3 2012 basalte Table of contents: 1. Introduction... 5 2. Installation... 6 2.1 Identifying the parts... 7 2.1.1 Front view
More informationUCM/Heatmiser Manual. Section 1 Introduction... Section 2 Connections and Settings... Section 3 Heatmiser UCM Configurator...
Section 1 Introduction...................................... Specifications.................................................. 2 What is Included............................................... 2 Interfaces
More informationcomfort solution overview
Advanced Comfort Features For Today s Digital Lifestyle comfort solution overview { A Vantage system gives you unparalleled control of comfort throughout your home. Whether it s an evening cocktail party
More informationSophisticated yet simple energy-efficient lighting solutions
Lighting Sophisticated yet simple energy-efficient lighting solutions Dynalite System Integration Within any modern project, many third-party systems can be found performing different roles. Each separate
More informationSophisticated yet. solutions. Dynalite Integration Devices. Benefits. Features. Application
Lighting Sophisticated yet simple energyefficient lighting solutions Within any modern project, many third-party systems can be found performing different roles. Each separate system may use a different
More informationOmni II Version 2.10 Firmware Release
Omni II Version 2.10 Firmware Release ADD THIS DOCUMENT TO YOUR OMNI II OWNER S MANUAL Description The Omni II Version 2.10 firmware adds the following new features: Support for the CentraLite LiteJet
More informationDesigned by installers,
Designed by installers, made by Philips Designed by you for your customer Everything an enduser could wish for The original Philips Pronto singlehandedly created a new class of programmable touchscreen
More informationIntegration Note. Virtual Matrix: The driver offers the ability to receive the auxiliary input feed from up to six other Sonos units
Integration Note Manufacturer: Sonos Model Number(s): Sonos ALL Models up to ver. 7.1 g! Core Module Version: 8.0.278 Driver Developer: Core Programming Limited Document Revision Date: 03/01/2017 OVERVIEW
More informationVC2100 / VC MB Digital Event Recorder
VC2100 / VC2100 32MB Digital Event Recorder Product Description: This system includes one VS2100 single channel digital event recorder and one color camera. It will automatically have image capture or
More informationGVS K-BUS R KNX/EIB Push Button Sensor Contents 1. Summary
Guangzhou Video-star Electronics Industrial Co., Ltd K-BUS R Push Button Sensor User manual-ver. 1.1 CHKP-01/01.1.xx CHKP-02/01.1.xx CHKP-03/01.1.xx KNX/EIB Intelligent Installation Systems GVS K-BUS R
More informationUSER MANUAL RC-76M/RC-712M MODEL: P/N: Rev 3
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: RC-76M/RC-712M P/N: 2900-300329 Rev 3 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions 3 2.3 Recycling
More informationABB i-bus EIB / KNX Shutter Actuator with Manual Operation, 4-fold, SMI, MDRC JA/S 4.SMI.1M. Product Manual. Intelligent Installation Systems ABB
Product Manual ABB i-bus EIB / KNX Shutter Actuator with Manual Operation, 4-fold, SMI, MDRC JA/S 4.SMI.1M Intelligent Installation Systems ABB JA/S 4.SMI.1M Shutter Actuator with Manual Operation, 4-fold,
More informationApplication description. KNX Push-button module 1gang. KNX Push-button module 2gang
Application description KNX Push-button module 1/2gang Electrical/mechanical data: see the operating instructions for the product Order number Product designation Application programme TP product Radio
More informationSophisticated yet simple energy-efficient lighting solutions
Lighting Sophisticated yet simple energy-efficient lighting solutions Dynalite System Integration Within any modern project, many third-party systems can be found performing different roles. Each separate
More informationMaster room unit for RRV controllers
2 722 Master room unit for RRV controllers 2 wire bus connection QAX850 Multifunctional, digital room unit for installer and end-user interface with RRV controllers. Use Use Application Room unit in combination
More informationINSTALLATION MANUAL for the Application ihc-mirf
INSTALLATION MANUAL for the Application ihc-mirf Contents Introduction 3 Installing the application on a mobile phone 3 Settings 4 Control 12 Introduction The applications ihc-mirf (for mobile phones with
More informationRoom Controller. SE8300 Low Voltage Fan Coil Controller and Zone Controller
Room Controller Low Voltage Fan Coil Controller and Zone Controller Application specific controller with customizable covers and screen colours. The is a low voltage fan coil terminal equipment controller
More informationBACnet Product Overview
BACnet Product Overview Comfort and energy-saving of a HVAC system are all about control. With networking devices, you can monitor and control your equipment via a communication system anywhere and anytime
More informationOmniLT Version 2.9 Firmware Release
OmniLT Version 2.9 Firmware Release ADD THIS DOCUMENT TO YOUR OMNILT INSTALLATION MANUAL Description The OmniLT Version 2.9 firmware adds the following new features: HAI Lighting Control (HLC) integration
More informationYou, in an homy and environmental world
You, in an homy and environmental world www.eelectron.com Building and Home Evolution 24/03/11 1 What s this? www.eelectron.com Building and Home Evolution 24/03/11 2 NOT A SWITCH You, in an homy and environmental
More informationRVL470. Heating controller. G2522en. Installation Instructions. 1 Installation. 2 Commissioning Wall mounting DIN rail mounting
G2522en Heating controller Installation Instructions RVL470 1 Installation 1.1 Place of installation In a dry room, e.g. the boiler room Mounting choices: In a control panel (on the inner wall or on a
More informationOmniPro II Version 2.11 Firmware Release
OmniPro II Version 2.11 Firmware Release ADD THIS DOCUMENT TO YOUR OMNIPRO II INSTALLATION MANUAL Description The OmniPro II Version 2.11 firmware adds the following new feature: Support for OmniTouch
More informationRoller Shutter Guide. Radio Motors with Wireless Controls
Roller Shutter Guide Radio Motors with Wireless Controls Technology an integral part of everyday life Introducing the next generation roller shutter motor and control solutions from SWS UK. In todays world,
More informationRoller Shutter Guide. Radio Motors with Wireless Controls
Roller Shutter Guide Radio Motors with Wireless Controls Technology an integral part of everyday life Introducing the next generation roller shutter motor and control solutions from SWS UK. In todays world,
More informationControl4 DIN Rail Lighting
Control4 DIN Rail Lighting Life s Better When Everything Works Together Want to change the moods and atmosphere in each room of the house? Using conventional lights, energy saving lights, LEDs and want
More informationRC-SV Configuration Guide (Rev 4)
Kramer Electronics, Ltd. RC-SV Configuration Guide (Rev 4) Software Version 2.1.2.69 Intended for Kramer Technical Personnel or external System Integrators. To check that you have the latest version, go
More informationUser Manual. Logic Timer Module. SB-DN-Logic960.
Logic Timer Module www.hdlautomation.com Document updates: Version Date Description V1.0 2015.01.26 Finish new document INDEX 1. Overview...1 1.1 General Information...1 1.1.1 Description...1 1.1.2 Mounting...
More informationdigitalstrom Planning handbook
digitalstrom Planning handbook 2 / 32 Author: digitalstrom AG Copyright 2014 digitalstrom.com All rights and technical changes reserved at all times. A1121D003V004EN / 28.02.2014 3 / 32 Preface What is
More informationCommunicative controller for VAV systems
FCR015 Communicative controller for VAV systems Summary FCR015 is a communicative controller for heating and cooling panels and a VAV (variable air volume) damper. It measures temperature and CO 2 concentration
More informationRenaming presets Clearing a preset Partial preset definition Control RS COM Port settings...
1 Table of Contents Introduction... 4 MBC-16Z Setup... 5 Minimum Requirements... 5 Installation... 5 Adjusting Mixer to MBC-16Z... 9 Mixer Definitions... 9 Zones Definitions... 9 Audio Sources and Channels
More informationRC-CDTO. Pre-programmed room controller with display, communication and three-point control
revision 02 2016 RC-CDTO Pre-programmed room controller with display, communication and three-point control RC-CDTO is a complete pre-programmed room controller from the Regio Midi series intended to control
More informationCompact controller for single room solutions
Multipurpose Controllers DDMC-GRMS Multipurpose Modular Room Controller Compact controller for single room solutions The Philips Dynalite DDMC-GRMS is a general room automation and energy management system.
More informationLIGHTIFY App - User-Guide
LIGHTIFY App - User-Guide App Version 1.9.2 For me, light is for reinventing my home. What is light to you? Discover a new dimension of light Control your lights individually or in groups at home or on
More informationPre-programmed room controller with display and communication
revision 10 2017 RC-C3DOC Pre-programmed room controller with display and communication RC-C3DOC is a complete pre-programmed room controller from the Regio Midi series intended to control heating, cooling
More informationSTANDALONE INTERFACES USB-DMX 512 & 1024 CHANNELS V.1.1
STANDALONE INTERFACES USB-DMX 512 & 1024 CHANNELS V.1.1 SUMMARY Hardware technical specifications... 3 Front Face of the 512 / 1024 channels interfaces... 4 Side Faces of the 512 / 1024 channels interfaces...
More informationRTC-Bridge User Manual
RTC-Bridge User Manual Contents RTC-Bridge User Manual... 1 What is RTC-Bridge... 2 Getting started with RTC-Bridge... 2 Basic Configuration of the RTC-Bridge... 3 Setting House Number and Geographic Location...
More informationOmni II Version 2.9 Firmware Release
Omni II Version 2.9 Firmware Release ADD THIS DOCUMENT TO YOUR OMNI II OWNER S MANUAL Description The Omni II Version 2.9 firmware adds the following new features: HAI Lighting Control (HLC) integration
More informationOmniLT Version 2.10 Firmware Release
OmniLT Version 2.10 Firmware Release ADD THIS DOCUMENT TO YOUR OMNILT OWNER S MANUAL Description The OmniLT Version 2.10 firmware adds the following new features: Support for the CentraLite LiteJet and
More informationRoom Temperature Controller
3 023 Room Temperature Controller for four-pipe fan coil units RCC30 Outputs for on / off valve actuators Outputs for three-speed fan Control depending on room or return air temperature Operating modes:
More informationCompass RTU Guide. Version 3.x
Compass RTU Guide Version 3.x Compass RTU Guide Ver 3.x OSSI W228 N727 Westmound Dr Waukesha WI 53186 USA TEL: 262-522-1870 FAX: 262-522-1872 Ossi-usa.com Intelli-Site Security Management Software Compass
More informationPush-buttons 18. Light scenes push-buttons 21. Push-buttons with thermostat 22. Labelling ields 24
A wide array of alternative materials and colours have been added to the convenient variety of KNX functionality of the. Frameless KNX push-button with full-material rockers (glass, stainless steel and
More informationIMPROVED HARDWARE FEATURES
IMPROVED HARDWARE FEATURES 1. FOURTEEN SEGMENT DISPLAYS Improvement from the seven-segment displays on the DynaTrol 600. All letters can be represented on these displays; some messages will change from
More informationSupplementary operating instructions for your air curtain system Controller TMC 500
Supplementary operating instructions for your air curtain system Controller TMC 500 (Translation of the original) Serial number: Year: Please quote this number when contacting customer service! Date 08.04.2016
More informationSmall and Medium Building New and Renovation Prescription Assistance Complete Solution
Small and Medium Building New and Renovation Prescription Assistance Complete Solution 1 1) Introduction... 3 2) Control/Automation of the building... 4 2.1) Control interfaces... 4 2.1.1) Commands by
More informationService Section. December 2003
Service Section December 2003 Network Interface Module (NIM) Family Transceiver Boards NIM NIM PC Ver 2 S-NIM G-WAY NIM TELE Transceiver Boards (TX Boards) Extend the communication distance between the
More informationUSER S MANUAL. DAS-G01 The Power of Tomorrow
USER S MANUAL DAS-G01 The Power of Tomorrow Richmond Heights 2018 0 USER S MANUAL DAS-G01 The Power of Tomorrow Richmond Heights 2018 Page 1 USER'S MANUAL TABLE OF CONTENTS Page # 1.0 GENERAL INFORMATION...
More informationIntesisBox KNX - AIRZONE
IntesisBox KNX - AIRZONE Gateway for the integration of Airzone InnoBUS into KNX systems. Full integration of Airzone InnoBUS air conditioning with KNX control systems. CS CS KNX EIB Bus IntesisBox RS485
More informationControl4 Driver. for. KNX Universal Thermostat
Control4 Driver for KNX Universal Thermostat 1 Introduction This document provides details for installing the Janus KNX Universal Thermostat driver into a Control4 installation. Additionally, it provides
More informationCrestron Pyng OS for PYNG-HUB
Crestron Pyng OS for PYNG-HUB Product Manual Crestron Electronics, Inc. Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive,
More informationAdvanced Comfort Features For Today s Digital Lifestyle
Advanced Comfort Features For Today s Digital Lifestyle comfort solution overview { A Vantage system gives you unparalleled control of comfort throughout your home. Whether it s an evening cocktail party
More informationADVANCED REMOTE CONTROL
ADVANCED REMOTE CONTROL (SUITS IP28) INSTALLATION & OPERATING INSTRUCTIONS 918-962 12/07/10 The Advanced Remote Control is tested safe when installed in accordance with this installation manual. It is
More informationSemi flush-mounted room temperature controllers with LCD
s 3 077 RDD310 RDE410 Semi flush-mounted room temperature controllers with LCD For heating systems RDD310 RDE410 RDD310 and RDE410 features: Operating voltage AC 230 V 2-position control with On / Off
More informationDomotica 2.1 Quick reference guide
Domotica 2.1 Quick reference guide revision 1.8 Follow Domotica on Facebook at address: http://www.facebook.com/domoticaingegni and click on to be always up to date on Domotica news Follow Domotica on
More informationEasy Setup Guide. 1 Preparation. English. AV Receiver. Accessories. Cables required for connections
UA Preparation Accessories AV Receiver Check that the following accessories are supplied with the product. Remote control Batteries (AAA, R0, UM-4) (x) Easy Setup Guide English YPAO microphone AM antenna
More informationGira Event The new definition
Gira Event The new definition New. Gira Event Clear. Clear, deep appearance in six colours. Gira Event Opaque. Seven colours in translucent material. Gira Event. Four colour variants in high quality thermoplastic.
More information