Installation manual OPTIKA -Minilane

Transcription

1 Content 1. Overview 2. Wiring of the devices 3. HiVoltage-Box 3.1. Single phase 3.2. Two phases 3.3. Three phases 4. The components 4.1. Interface to the pinsetter 4.2. Wiring of the components on the RS485 bus 4.3. Wiring Hivoltage Box Interface 4.4. Wiring Interface - Pinsetter 5. Interface to the pinsetter 6. Lanecomputer 7. Settings on Lanecomputer 8. Attachment A (In- und Outputs on the Seil-Interface) Seite 1 von 1 1

2 1. Overview Overview Seite 2 von 2 2

3 2. Control Unit Seite 3 von 3 3

4 3. HiVoltageBox 3.1. Single phase Seite 4 von 4 4

5 3.2. Two phases Seite 5 von 5 5

6 3.3. Three phases Seite 6 von 6 6

7 4. The components 4.1. Interface to the pinsetter Interface for Lane 2: Jumper is set Seite 7 von 7 7 If this interace is last component on the cat5-bus: All 3 Jumpers are set (Termination Jumpers)

8 4.1. Lanecomputer VGA-Monitor Lane 1 (LCD-TV) VGA-Monitor Lane 2 (LCD-TV ) Network-Plug CCS2000 Communication bus 1 = - 2 = + Plug for RS485 bus (to the interfaces) 3 = - 4 = + 5 = Earth (GND) NOTE: The Plugs on the interfaces have 5 wires!! Use only wires 3,4,5 Seite 8 von 8 8

9 (Lanecomputer) 4.2. Wiring of the components on the RS485 bus Interface-(or Coin-Interface) Interface Lane 1 Interface Lane 2 Lanepc (Wiring of the components on the RS485 bus) Cat-5 cable 1+2 = 12V AC 3=Communication (-) 4=Communication (+) 5=Earth (GROUND) Cat-3 cable 3=Communication (-) 4=Communication (+) 5=Earth (GROUND) Note: On the interafce for lane 2: Set the jumper (see 4. Interface for the pinsetter) On the last component on the bus (either interface for the pinsetter or coin-interface) set the termination jumpers. In the example above this is the coin-interface. Seite 9 von 9 9

10 4.3 Wiring Hivoltage Box - Interface To the pinsetter(s) To the HiVo Box 4pins plug 1,2 Ballcounter 3,4 Remote Manager Switch 3pins plug Common elevator Seite 10 von 10 10

11 4.4 Wiring Interface - Pinsetter Cable to motor control 14pin flat cable Cable to pinsetter 36pin flat cable (Interface to pinsetter) Seite 11 von 11 11

12 5. Lanecomputer Setup OPTIKA supports various types of pinsetters in different countries, with different needs and requirements. To achive this the systems offers many options and features for customization. For Minilane bowling (for pinsetters with strings) the most important settings are pointed out below. Entering the setup mode using a standard BMS-Keyboard: Hold down the Eye buttohn and type: P R O G P When a standard PC-Keyboard is used (PS-2 only): Hold down the Shift button and press PROGP Navigation: Use the arrow keys for navigation: or: or: or: When a standard PC-Keyboard is used (PS-2 only): Use the arrow buttons Selection: Press Start : START When a standard PC-Keyboard is used (PS-2 only): Press the PageUp button Seite 12 von 12 12

13 Setupscreen Note: The appropriate setup is usually made from factory. Do not change or modify them if not necessary. Seite 13 von 13 13

14 Time delay between ball passes the photocell and machine is starting impuls Lanenumber (left lane only) Subject Default value Important for Minilane measuring delay ball 1+2[ms] 1500 Yes Lane number (left) 1 (or 3 or 5..) Yes language English Yes top-5 (automatic top-5 management) 1 Yes graphic-set 0 No distance of photocells 30 No display of graphics 0-3 Open+League No display of ball speed No No keyboard USA No handicap No showtime picture [sec]: max. timeout for graphics 6 Yes speedlimit 0 No showtime waitpictures [sec]: display time for graphics when system is idle 19 Yes Seite 14 von 14 14

15 Subject Default value Important for Minilane show scrolltext 1 Yes speed 0 No pulstime trigger relay 1000 No pulstime set relay 1000 No pulstime set relay (10 th frame) No puls set relay 0 No ON-time set relay 5000 No OFF-time set relay 1000 No pulstime stepper1-relay 1000 No pulstime stepper2-relay 1000 No pulstime ball lift-relay [sec] (relay time for preference 180 Yes when ball passes the photocell) bumper-relay: Puls=1; Cont=0 0 Yes Seite 15 von 15 15

16 Subject Default value Important for Minilane pulstime bumper-relay [msec] 999 No pulstime call relay [sec] 10 No delay time pinsetter OFF [sec] 10 No time for practice [min] 10 No pinsetter sets in practice 1 No automatic correction 0 No count frame 11/12 0 No monitor: VGA=2 15khz=1 25Khz=0 2 No pulstime stepper3-relay 1000 No pinsetter A-2/S=1 GSxx=2 0 No foul set: 0=normal; 1=A-2 0 No block keyb. After name entry(0,1) 0 No Seite 16 von 16 16

17 Subject Default value Important for Minilane pinsetter ON/OFF Relay 2 Yes trigger No No set No No stepper 1 No No stepper 2 No No stepper 3 No No Ball lift Relay 5 Yes bumper Relay 3 Yes call No No set 10 th frame No No Relay 2 nd ball-lamp No No Seite 17 von 17 17

18 Subject Default value Important for Minilane foul input No No 2 nd throw input No No free input No No sweeper input No No 3rd serial port No No IRT No No TCP/IP (0,1) 1 Yes IP (Port 23) This address depends on the lanenumber defaults: lane 1+2 : lane 3+4 : lane 5+6 : counter (build-in counters) (12 digits notation required!) Yes No Seite 18 von 18 18

19 Subject Default value Important for Minilane foul inversion 0 No max. 6 player (limit number of players to 6) 0 Yes prepaid: timeout[s] (Delay at game end before switching 60 Yes to idle. Only for prepaid games bungee timeout No No delay PinRel. After O [ms] 50 Yes delay for the spick Stop in O 0 Yes 0: no, stop only after detangle 1: Always stop in O No, foul or Fast-Reset 0 No Seite 19 von 19 19

20 Attachment A (In- and Outputs on the interface) Inputs : Input 1 Photocell 2 Detangle 3 ON/OFF 4 U-Signal 5 O-Signal Outputs: Rel. 1 Pinsetter-Motor 2 ON/OFF 3 Bumper 4 CrossLight 5 Ball-Lift 6 TrainLight Additional Relais ChaseLight Seite 20 von 20 20

21 IMPORTANT: - SWITCH OFF POWER before any manipulation! Seite 21 von 21 21