DORMA. Installation Manual Extension kit I/O module in the B6L 4P

Transcription

1 DORMA Installation Manual Extension kit I/O module in the B6L 4P

2 Contents Contents 1 General information Preface Correct use Safety instructions and warnings Other sources of information Disposal Operating principle Scope of delivery Installation Settings Module address Terminating resistors Configuration of relay contacts Inputs Digital inputs Tampering input Connecting/disconnecting the mains voltage Physical installation Electrical installation Optical interfaces and operating elements Online Bus activity Assignment of readers to input/output modules Terminal diagram Technical data Maintenance and troubleshooting Fuse Technical data

3 1. General information 1.1 Preface This installation manual is intended to assist you in connecting and putting into operation a second I/O module in the B6L 4P. 1.2 Correct use A second I/O module can be fitted into the box to increase the maximum number of doors operated by the B6L 4P from four to eight and is designed for use with this device only. Use for any other purpose than the one described is not permitted. 1.3 Safety instructions and warnings The I/O module extension kit has been designed and tested in accordance with all currently applicable technical regulations. All safety features were in proper working order when it left the factory. The user must observe the instructions and warnings given in this installation guide to maintain proper working order and ensure risk-free operation. The device may only be used for the purpose intended by the manufacturer. Installation and assembly of electrical equipment may be carried out by a qualified electrician only. Before opening the unit, always switch off the power supply and check that it is inactive by measuring the current. During installation, please ensure that the requirements laid down in the relevant equipment safety standard for the unit are adhered to since non-compliance could affect the safety of the device. Before switching on, ensure that the connected operating and control voltages do not exceed the permissible values specified in the technical data. This I/O module extension kit complies with EN Operating voltage 24 V/DC Protection Class III Electromagnetic compatibility: PCBs can be damaged by static electricity discharge, so suitable precautionary measures such as grounding must be implemented. The extension kit may only be operated when installed. The locking screws on unassigned connection terminals must be screwed in as far as they will go. If you believe that the device can no longer be operated safely, take it out of operation and secure it against accidental use. If a unit failure or malfunction may result in injury to persons or animals, or in damage to works equipment, this must be prevented by taking additional safety measures, such as limit switches and safety devices. General Installation Guidelines See Manual 1006G-B0 Drawing no.: 1101G-00-B2 Date: 01/12 V1.11 3

4 1. General information 1.4 Other sources of information Further documents are available on request. General installation guidelines Specifications for planning attendance recording and access control systems with our wired components. Planner Manual Examples of cross-system solutions B6L 4P Installation Manual DORMA Allgemeine Installationsrichtlinien Sicherungstechnik Zutrittskontrolle Zeiterfassung Zeitwirtschaft Systemübersicht Systemlösung Funktionsweise Mechatronik Fluchtweg & TMS Funktionsweise Innenbereich Außenhaut Gelände Funktionsweise 1.5 Disposal This I/O module extension kit has been manufactured using high-quality materials and components that can be recycled. Information for EU countries This I/O module extension kit falls under the European Directive 2002/96 EC and therefore must not be disposed of with household waste. We, the manufacturer, will take back our electric and electronic products and dispose of them for you free of charge. You may also contact your waste disposal company instead. 1.6 Functional principle The B6L 4P I/O module determines the status of doors in an access control system and controls the electrical functional units. This module features nine digital inputs and eight relays for this purpose, each with a non-isolated changeover contact. The status of the non-isolated digital inputs is transmitted to a higher-level control unit. The control unit evaluates statuses and can operate the relays. Communication between the I/O module and the access control unit is sent via an RS485 interface. The B6L 4P I/O module is only available for direct installation in a B6L 4P. 4

5 1. General information The information provided in these assembly instructions may be modified without prior notification. All previous versions cease to be valid with the publication of these instructions. The information in these assembly instructions has been compiled to the best of our knowledge and in good faith. DORMA Time + Access GmbH accepts no liability for the correctness and completeness of the details provided. In particular, DORMA Time + Access GmbH cannot accept liability for any consequential damages due to incorrect or incomplete information. The recommendations for installation made in this manual are based on the assumption that prevailing basic conditions are favourable. DORMA Time + Access GmbH accepts no liability for the perfect functioning of the B6L 4P in nonsystem environments. Despite every effort to prevent mistakes, they can never be completely avoided. Therefore, we would be grateful to receive notification of any errors or omissions. DORMA Time + Access GmbH accepts no liability for the information included in this document being free of protected third party rights. DORMA Time + Access GmbH does not provide any licences to its own or to third party patents or other protected rights with this document. It is not permitted to print, reproduce or to pass this manual, or parts thereof, to third parties, other than for your own use, without the approval of DORMA Time + Access GmbH. Alle Rechte vorbehalten. Dorma Time + Access GmbH Postfach Bonn info@dorma-time-access.de Copyright 2013 by Dorma Time + Access GmbH 5

6 1. General information 1.7 Scope of delivery A 1x I/O module B 1x cover plate C 6x spacer bolts D 6x screws E 1x bus connection cable F 1x 24 V connection cable G 1x manual A G C 6x D 6x DORMA Installation Manual Extension kit I/O module in the B6L 4P E B F 6

7 2. Installation 2.1 Settings Module address Before fitting the module, you must check the bus address of the new device and re-set if necessary. Settings are made with the SW103 switch. The address for the extension I/O module is 18. The SW103 should be set as in the diagram. OFF ON SW102 SW Terminating resistors The terminating resistors in the existing I/O module must be set to "Off" before fitting the second I/O module. The terminating resistors in the second I/O module must be set to "On". SW101 und SW102 On Off Terminating resistors on On Off Terminating resistors off 7

8 2. Installation 2.2 Configuration of relay contacts SW102 SW101 Jumpers in factory default setting The I/O module features eight relays. Each relay has a 4-pin plug connector in front of the output terminal. The relay contacts can be connected separately from one another with two jumpers so that they are isolated (Jumper Position A) or they can be allocated an auxiliary voltage (internal supply; Jumper Position B). 24V Jumpers in factory default setting Changeover contact (common) Closing contact (normally open) You must remember that you may only connect eight low-power strikes with 150 ma power consumption each to ensure a 30-minute emergency power supply can be provided for the whole access control. Jumper Setting A (factory default setting) Relay jumper setting in the case of isolated contacts Maximum current per relay contact: 1 A. 24V Each relay context is equipped with a self-resetting thermal fuse. Inductive loads must be provided with freewheeling diodes if a DC power supply is used. When connecting an alternating current, an RC element or a voltage regulative diode (Item no ) must be used in place of a freewheeling diode for interference suppression. Jumpers in factory default setting Changeover contact (common) Closing contact (normally open) Jumper Setting B Relay jumper setting in the case of looped-in voltage 2.3 Inputs Digital inputs The I/O module has nine optocoupler inputs (negative switching). The contact load is a maximum of 10 ma. The inputs must not be supplied with an external voltage Tampering input The tampering input on the extension I/O module is not used. No electrical connections need to be made. Digin1,...9 GND IN ST301,

9 2. Installation 2.4 Connecting/disconnecting the mains voltage Si 40 2,5 1. N 10A L

10 2. Installation 2.5 Physical installation Open the B6L 4P box while observing the aforementioned safety instructions. Take the I/O module (A) out of its protective sleeve while taking into account the safety instructions on handling components at risk from ESD and fasten it to the installed I/O module using spacer bolts. After fitting the cover plate (B) for the newly installed I/O module, physical installation is complete. A C B D 10

11 2. Installation 2.6 Electrical installation The enclosed cables are used to connect the bus and the 24 V current. The bus cable (E) connects the ST101 plugs on the two I/O modules with one another. The 24 V cable (F) connects the ST311 plugs on the two I/O modules with one another. The connection to the TP4 base card remains unchanged via the ST102 plug-in connection in the lower I/O module. SW102 SW101 SW102 SW101 ST311 ST301 ST302 ST303 ST304 ST305 ST306 ST307 ST308 ST309 ST101 ST102 ST301 ST302 ST303 ST304 ST305 ST306 ST307 ST308 ST309 ST101 F E 11

12 2. Installation 2.7 Optical interfaces and operating elements SW102 SW Online LED Yellow Off Meaning The online LED lights up as long as the I/O module is being polled by the higher-level control unit. If the I/O module is not polled for more than 15 seconds, the online LED goes out Bus activity LED Off Yellow Bedeutung No reference data to/from the I/O module via the communication interface Receiving reference data Green Red Sending reference data a) Positive DP1 response telegrams b) DP1 message telegrams Sending reference data a) Negative DP1 response telegrams 12

13 2. Installation 2.8 Assignment of readers to input/output module L N INPUT OUT BAT 10A 503 Si 40 2,5 CH OG BU MA PG SW102 SW101 ST401 ST402 ST403 ST404 ST405 ST406 ST407 ST408 ST301 ST302 ST303 ST304 ST305 ST306 ST307 ST308 ST309 The extension I/O module is connected to the electrical operating units for Doors 5 to 8 in the same ways as for Doors 1 to 4. The following table gives an overview of connections: Door Cards Reader I/O module 1 Out Door relay (operating current strike) I/O module 1 Out Alarm relay I/O module 1 In Door status contact 5 9 ST401 ST301 I/O module 1 In Door opening contact 5 10 ST402 ST ST403 ST ST404 ST ST405 ST ST406 ST ST407 ST ST408 ST308 13

14 2. Installation 2.9 Terminal diagram SW102 SW101 ST301 ST401 ST402 ST403 ST404 ST405 ST406 ST407 ST408 ST101 ST102 ST302 ST303 ST304 ST305 ST306 ST307 ST308 ST309 NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC...max. 4x each...max. 4x each Operating current Door opener Door 5 Alarm relay Door status contact Door 5 Door opening contact Connection to the lower I/O module Connection to the lower I/O module 14

15 3. Maintenance 3.1. Maintenance and troubleshooting Fuse An internal SMD safety fuse SI101 (Littlefuse type T, 2AT) is installed as protection in the bottom right-hand half of the casing. There is also an SI102 replacement fuse on the component module. SW102 SW101 15

16 4. Technical data Technical data I/O-Modul B6L 4P Supply voltage via ST101 and ST V DC Supply voltage via ST311/ST V DC maximum Power consumption I/O module itself: max. 5 W (200 ma at 24 V) Supply via ST101/ST102: about 2 W Interface RS485 DP1 protocol Outputs 8x relays contact rating max. 24 W Digital inputs 9x optocouplers (negative switching) Max. load: 24 V DC/10 ma Ambient conditions Operating temperature range: -20 C to +50 C Storage temperature range: -20 C to +70 C Humidity range: up to 80% non-condensing General design DIN EN Protection rating IP00 Resistance to interference See B6L 4P Installation Manual Interference emissions See B6L 4P Installation Manual We reserve the right to make technical modifications and improvements in the course of the further development our equipment. DORMA Time + Access GmbH DORMA GmbH + Co. G 16 Postfach D Bonn Mainzer Straße D Bonn Tel. +49 (0) 2 28/ Fax +49 (0) 2 28/ Postfach D Ennepetal DORMA Platz 1 D Ennepetal Tel. +49 (0) / Fax +49 (0) /