D11 Series: Visible Green, Blue or White LED Light Source

Transcription

1 Datasheet Low cost self-contained sensors for use with plastic fiber optics Visible green, blue or white LD light source for use in color mark sensing and other lowcontrast sensing applications Low-cost, 0 V dc to 0 V dc, self-contained sensors for use with all Banner plastic fiber optics Compact mm-wide housing designed for DIN rail mounting; also mounts to other surfaces using the supplied mounting bracket Choice of NPN (sinking) or PNP (sourcing) complementary outputs one normally open and one normally closed; 50 ma output load rating Normally-closed output may be wired as a diagnostic alarm to alert personnel to marginal sensing conditions Fast, 500 microsecond (0.5 millisecond) output response LD status indications for power ON, output overload, fiber alignment, and marginal gain conditions Choose models with integral cable or pico-style quick disconnect (QD) connector; 9 m (0 ft) cables are also available WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Note: Range varies by sensing mode and fiber optics used. Visible green, 55 nm Models Cable upply Voltage Output Type DN6FPG Complementary NPN (sinking) DN6FPGQ 0 V dc to 0 V dc DP6FPG Complementary PNP (sourcing) DP6FPGQ Visible blue, 70 nm Models Cable upply Voltage Output Type DN6FPB Complementary NPN (sinking) DN6FPBQ 0 V dc to 0 V dc DP6FPB Complementary PNP (sourcing) DP6FPBQ Visible white, 50 nm to 650 nm Models Cable upply Voltage Output Type DN6FPW Complementary NPN (sinking) DN6FPWQ 0 V dc to 0 V dc DP6FPW Complementary PNP (sourcing) DP6FPWQ U.. Patent # To order the 9 m (0 ft) PVC cable model, add the suffix "W/0" to the cabled model number. For example, DN6FPG W/0. Models with a quick disconnect require a mating cordset. Original Document 9 Rev. B 6 March 07 9

2 Features ensitivity Adjustment Power Indicator Output Indicator Amber Output Indicator Green Power ON Indicator Plastic Fiber mitter Port 5-Turn ensitivity (Gain) Control Mounting Bracket (Included) Plastic Fiber Receiver Port Installation Mount the D on a DIN rail or the included bracket. DIN Rail Installing Plastic. Cut the fiber ends according to the instructions included with the fibers.. lide the fiber gripper up (open).. If you are using 0.5 mm or mm (0.00 inch or 0.00 inch) diameter fibers: Insert the adaptor into the ports as far as it will go. Fiber adapter. For all fiber diameters: Insert the prepared plastic fiber sensor ends gently into the ports as far as they will go. 5. lide the fiber gripper back down to lock it. - Tel: P/N 9 Rev. B

3 Wiring Diagrams NPN Outputs tandard Wiring 0-0V dc PNP Outputs tandard Wiring 0-0V dc Key = Brown = White = Blue = Black NPN Outputs Alarm Wiring PNP Outputs Alarm Wiring Alarm 0-0V dc Alarm 0-0V dc Quick disconnect (QD) wiring diagrams are functionally identical. P/N 9 Rev. B - Tel:

4 pecifications Required Fiber Optic Cable PI or PB series plastic fibers ensing Beam Visible green, 55 nm ; Visible blue, 70 nm; Visible white, 50 nm to 650 nm upply Voltage and Current 0 V dc to 0 V dc at 5 ma, exclusive of load current upply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration Complementary: one normally open (N.O.) and the other normally closed (N.C.); N.C. output may be wired as diagnostic alarm output by reversing power supply connections (see wiring diagrams); Outputs are NPN (sinking) or PNP (sourcing), depending on model Diagnostic alarm output energizes whenever excess gain falls to between x and.5x in the light condition; this output corresponds to flashing yellow indicator LD. Output Rating 50 ma maximum (each output); the total load may not exceed 50 ma Off-state leakage current: < 5 microamps at 0 V dc On-state saturation voltage: < V at 0 ma dc; <.5 V at 50 ma dc Output Protection Circuitry Protected against false pulse on power-up (false pulse protection circuit causes a 0. second delay on power-up); short-circuit protected Output Response Time 500 microseconds ON and OFF Repeatability 60 microseconds; response time and repeatability are independent of signal strength Adjustments ensitivity control on top of housing (5-turn slotted brass screw, clutched at both ends of travel) Indicators Two LDs: Green and amber Green steady = power to sensor is ON Green flashing = output is overloaded Amber steady = normally open output is conducting Amber flashing = marginal excess gain ( to.5x) in light condition = alarm output ON Construction Black AB flame retardant housing with acrylic cover tainless steel M x 0.5 hardware for use with AB mounting bracket (supplied) nvironmental Rating IC IP5; NMA Connections or 9 m (0 ft) attached cable, or -pin Pico-style quick-disconnect fitting; cables for QD models are purchased separately Operating Conditions Operating Temperature: 0 C to 55 C ( F to F) 90% at 50 C maximum relative humidity (non-condensing) Required Overcurrent Protection WARNING: lectrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with external fusing or via Current Limiting, Class Power upply. upply wiring leads < AWG shall not be spliced. For additional product support, go to Certifications upply Wiring (AWG) Required Overcurrent Protection (Amps) Dimensions lide Up to Release 5.0 mm (.8 in) 9.0 mm (. in) lide Up to Release 5.0 mm (.8 in) 9.0 mm (. in) 7.6 mm (0.69 in) 7.6 mm (0.69 in) 6. mm (.5 in).0 mm (0. in) Figure. Cabled Models 6. mm (.5 in).0 mm (0. in) 79.0 mm (. in) Figure. QD Models U.. Patent # Tel: P/N 9 Rev. B

5 5.5 mm (0.").0 mm (0.") 8.6 mm (0.") 5.0 mm (.8") 5. mm (0.99") 9.9 mm (0.9") x.5 mm (0.") x C sink ø 7.9 mm (0."). mm (0.") deep ø. (0.8") thru Figure. Mounting Bracket x ø.8 mm (0.5") 5.6 mm (.0") 9.6 mm (0.8") x ø.5 mm (0.8") 0. mm (.9").8 mm (0.9").5 mm (0.0") 5.0 mm (0.0") Performance Curves Diffuse mode performance based on 90% reflectance white test card X C G A I N DFPG, DFPB and DFPW eries Diffuse Mode Plastic PBT66U PBT6U.0 mm 0 mm 00 mm 000 mm 0.0 in 0. in.0 in 0 in DITANC X C G A I N mm 0.00 in DFPG, DFPB and DFPW eries Opposed Mode Plastic PIT6U.0 mm 0.0 in PIT6U DITANC 0 mm 0. in PIT66U 00 mm.0 in Accessories -Pin nap-on M8/Pico-tyle Cordsets Model Length tyle Dimensions Pinout (Female) Typ. PKG- m (6.56 ft) traight 9 Typ. ø 9.0 PKWZ- m (6.56 ft) Right-Angle 5 Typ. = Brown = White = Blue = Black ø 0.9 P/N 9 Rev. B - Tel:

6 Banner ngineering Corp. Limited Warranty Banner ngineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner ngineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THI LIMITD WARRANTY I XCLUIV AND IN LIU OF ALL OTHR WARRANTI WHTHR XPR OR IMPLID (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MRCHANTABILITY OR FITN FOR A PARTICULAR PURPO), AND WHTHR ARIING UNDR COUR OF PRFORMANC, COUR OF DALING OR TRAD UAG. This Warranty is exclusive and limited to repair or, at the discretion of Banner ngineering Corp., replacement. IN NO VNT HALL BANNR NGINRING CORP. B LIABL TO BUYR OR ANY OTHR PRON OR NTITY FOR ANY XTRA COT, XPN, LO, LO OF PROFIT, OR ANY INCIDNTAL, CONQUNTIAL OR PCIAL DAMAG RULTING FROM ANY PRODUCT DFCT OR FROM TH U OR INABILITY TO U TH PRODUCT, WHTHR ARIING IN CONTRACT OR WARRANTY, TATUT, TORT, TRICT LIABILITY, NGLIGNC, OR OTHRWI. Banner ngineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner ngineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner ngineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. pecifications and product information in nglish supersede that which is provided in any other language. For the most recent version of any documentation, refer to: Banner ngineering Corp. All rights reserved