MODEL NO.: V236H1 SUFFIX: LE6

Size: px

Start display at page:

Download "MODEL NO.: V236H1 SUFFIX: LE6"

Andrea Heath
6 years ago
Views:

1 Tentative Specification Preliminary Specification Approval Specification MODEL NO. V236H SUFFIX LE6 Customer APPROVED BY SIGNATURE Name / Title Note Please return copy for your confirmation with your signature and comments. Approved By Checked By Prepared By Chao-Chun Chung Roger Huang Bowei Huang

2 CONTENTS. OVERVIEW FEATURES APPLICATION GENERAL SPECIFICATIONS MECHANICAL SPECIFICATIONS ABSOLUTE RATINGS OF ENVIRONMENT PACKAGE STORAGE ELECTRICAL ABSOLUTE RATINGS TFT LCD MODULE BACKLIGHT CONVERTER UNIT TFT LCD MODULE BACKLIGHT CONNECTOR PIN CONFIGURATION LED LIGHT BAR CHARACTERISTICS LIGHTBAR CONNECTOR PIN ASSIGNMENT LVDS INPUT SIGNAL SPECIFICATIONS TFT LCD MODULE TFT LCD MODULE INPUT BLOCK DIAGRAM OF INTERFACE LVDS INTERFACE COLOR DATA INPUT ASSIGNMENT INPUT SIGNAL TIMING SPECIFICATIONS POWER ON/OFF SEQUENCE TEST CONDITIONS OPTICAL SPECIFICATIONS...23 From 液晶之家

3 8. ASSEMBLY AND HANDLING PRECAUTIONS SAFETY PRECAUTIONS SAFETY REVIEW SAFETY STANDARDS CMI MODULE LABEL PACKING SPECIFICATIONS PACKAGING METHOD...29 From 液晶之家

4 REVISION HISTORY Version Date Page(New) Section Description Ver. 2. Jan. 5, 22 All All The Approval specification was first issued.

5 . GENERAL DESCRIPTION. OVERVIEW V236H-LE6 is a 23.6 TFT Liquid Crystal Display module with WLED Backlight unit and 3 pins 2ch-LVDS interface. This module supports 92 x 8 Full HDTV format and can display up to 6.7M (6 bit +Hi-FRC) colors. The converter module for Backlight is not built in..2 FEATURES Extra-wide viewing angle. High contrast ratio. Fast response time. High color saturation. Full HD (92 x 8 pixels) resolution. DE (Data Enable) only mode. LVDS (Low Voltage Differential Signaling) interface. RoHS compliance..3 APPLICATION Standard Living Room TVs MFM Application.4 GENERAL SPECIFICATIONS Item Specification Unit Note Active Area 52.28H) x (V) ( diagonal) mm Bezel Opening Area (H) x (V) mm () Driver Element a-si TFT active matrix - - Pixel Number 92 x R.G.B. x 8 pixel - Pixel Pitch(Sub Pixel).275(H) x.275(v) mm - Pixel Arrangement RGB vertical stripe - - Power consumption 9.26W (Max.) [Cell PW 6.W (Max.) + BLU PW 3.26W (Max.)] Watt (2) Display Colors 6.7M (6 bit +Hi-FRC) color - Display Operation Mode Transmissive mode / Normally white - - Surface Treatment Anti-Glare coating (Haze 25%) - Note () Please refer to the attached drawings in chapter 9 for more information about the front and back outlines. Note (2) Please refer sec 3. and 3.2 for more information of Power consumption

6 .5 MECHANICAL SPECIFICATIONS PRODUCT SPECIFICATION Item Min. Typ. Max. Unit Note Horizontal (H) mm () Module Size Vertical (V) mm () Depth (D) -..5 mm () Weight g - Note () Please refer to the attached drawings for more information of front and back outline dimensions.

7 2. ABSOLUTE MAXIMUM RATINGS 2. ABSOLUTE RATINGS OF ENVIRONMENT PRODUCT SPECIFICATION Item Symbol Min. Value Max. Unit Note Storage Temperature TST ºC () Operating Ambient Temperature TOP 5 ºC (), (2) Shock (Non-Operating) SNOP - 5 G (3), (5) Vibration (Non-Operating) VNOP -. G (4), (5) Note () Temperature and relative humidity range is shown in the figure below. (a) 9 %RH Max. (Ta 4 ºC). (b) Wet-bulb temperature should be 39 ºC Max. (Ta > 4 ºC). (c) No condensation. Note (2) The maximum operating temperature is based on the test condition that the surface temperature of display area is less than or equal to 65 ºC with LCD module alone in a temperature controlled chamber. Thermal management should be considered in final product design to prevent the surface temperature of display area from being over 65 ºC. The range of operating temperature may degrade in case of improper thermal management in final product design. Note (3) ms, half sine wave, time for ± X, ± Y, ± Z. Note (4) ~ 2 Hz, min, time each X, Y, Z. Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture.

8 2.2 PACKAGE STORAGE When storing modules as spares for a long time, the following precaution is necessary. (a) Do not leave the module in high temperature, and high humidity for a long time, It is highly recommended to store the module with temperature from to 35 at normal humidity without condensation. (b) The module shall be stored in dark place. Do not store the TFT-LCD module in direct sunlight or fluorescent light. 2.3 ELECTRICAL ABSOLUTE RATINGS 2.3. TFT LCD MODULE Item Symbol Min. Value Max. Unit Note Power Supply Voltage VCC V Logic Input Voltage VIN V () BACKLIGHT CONVERTER UNIT Item LED Forward Current Per Input Pin Symbol Value Min. Typ. Max. Unit I F ma Note () (2) Duty=% LED Pulse Forward Current Per Input Pin I FP 5 ma Pulse Widthmsec. and Duty3% Note () Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for input pin of LED light bar at Ta=25±2 (Refer to 3.2 for further information).

9 3. ELECTRICAL CHARACTERISTICS 3. TFT LCD MODULE PRODUCT SPECIFICATION (Ta = 25 ± 2 ºC) Parameter Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage V CC V () Rush Current I RUSH.52 3 A (2) Power Consumption P T W (3) White Pattern.4.43 A Power Supply Current Vertical Stripe.94.3 A Black Pattern.4.2 A (4) LVDS interface CMOS interface Differential Input High Threshold Voltage Differential Input Low Threshold Voltage V TH + mv V TL - mv Common Input Voltage V CM..2.4 V Differential input voltage V ID 2 6 mv Terminating Resistor R T ohm Logic High Input Voltage VIH V Logic Low Input Voltage VIL -.66 V (5) Note () The module should be always operated within the above ranges. Note (2) Measurement condition

10 Vcc rising time is 47us Vcc.9Vcc.Vcc GND 47us Note (3) The Specified Power consumption is under Vertical Stripe pattern. Note (4) The specified Max. power supply current is under the conditions at Vcc=5.V, Ta = 25 ± 2 ºC, f v = 75 Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern Active Area Active Area c. Vertical Stripe Pattern R G B R G B B R G B R G B R B R G B R G B R R G B R G B Active Area

11 Note (5) The LVDS input characteristics are as follows PRODUCT SPECIFICATION 3.2 BACKLIGHT CONNECTOR PIN CONFIGURATION 3.2. LED LIGHT BAR CHARACTERISTICS Parameter LED Light Bar Input Voltage Per Input Pin LED Light Bar Current Per Input Pin Symbol Value Min. Typ. Max. V PIN V Unit I PIN ma Power consumption P BL W (Ta = 25 ± 2 ºC) Note (), Duty=%, I L =65mA (), (2) Duty=% () Duty=%, I L =65mA LED Life time L LED 4, - - Hrs (3) Note ()LED light bar input voltage and current are measured by utilizing a true RMS multimeter as shown below Note (2) P BL (Typ.)= I PIN (Typ.) V PIN (Typ.) ( 4 ), P BL (Max.)= I PIN (Typ) V PIN (Max.) ( 4 ) input pins, LED light bar circuit is (5)Series, (4)Parallel. Note (3)The lifetime of LED is defined as the time when LED packages continue to operate under the conditions at Ta = 25 ±2 and I= (65)mA (per chip) until the brightness becomes 5% of its original value. Power supply CMI Converter With PWM Function V PIN, I PIN LED Backlight Module Series(5) Parallel(4) Function generator V PIN(8), I PIN(8)

12 3.2.2 LIGHTBAR CONNECTOR PIN ASSIGNMENT PRODUCT SPECIFICATION CN Pin number Description Cathode of LED string 2 Cathode of LED string2 3 VLED 4 VLED 5 Cathode of LED string3 6 Cathode of LED string4 Note() Connector WM N(FCN) or equivalent. Note(2) User s mating connector part No. IWF3-6(FCN) or compatible and hook width must be less than 4.5mm. 3.3 LVDS INPUT SIGNAL SPECIFICATIONS

13 4. BLOCK DIAGRAM OF INTERFACE 4. TFT LCD MODULE PRODUCT SPECIFICATION

14 5. INPUT TERMINAL PIN ASSIGNMENT 5. TFT LCD MODULE INPUT PRODUCT SPECIFICATION Pin Name Description RXO- Negative LVDS differential data input. Channel O (odd) 2 RXO+ Positive LVDS differential data input. Channel O (odd) 3 RXO- Negative LVDS differential data input. Channel O (odd) 4 RXO+ Positive LVDS differential data input. Channel O (odd) 5 RXO2- Negative LVDS differential data input. Channel O2 (odd) 6 RXO2+ Positive LVDS differential data input. Channel O2 (odd) 7 GND Ground 8 RXOC- Negative LVDS differential clock input. (odd) 9 RXOC+ Positive LVDS differential clock input. (odd) RXO3- Negative LVDS differential data input. Channel O3(odd) RXO3+ Positive LVDS differential data input. Channel O3 (odd) 2 RXE- Negative LVDS differential data input. Channel E (even) 3 RXE+ Positive LVDS differential data input. Channel E (even) 4 GND Ground 5 RXE- Negative LVDS differential data input. Channel E (even) 6 RXE+ Positive LVDS differential data input. Channel E (even) 7 GND Ground 8 RXE2- Negative LVDS differential data input. Channel E2 (even) 9 RXE2+ Positive LVDS differential data input. Channel E2 (even) 2 RXEC- Negative LVDS differential clock input. (even) 2 RXEC+ Positive LVDS differential clock input. (even) 22 RXE3- Negative LVDS differential data input. Channel E3 (even) 23 RXE3+ Positive LVDS differential data input. Channel E3 (even) 24 GND Ground 25 NC For LCD internal use only, Do not connect 26 NC For LCD internal use only, Do not connect 27 NC For LCD internal use only, Do not connect 28 VCC +5.V power supply 29 VCC +5.V power supply 3 VCC +5.V power supply Note () Connector Part No (P-TWO) or equivalent. Note (2) Mating Wire Cable Connector Part No. FI-X3H(JAE) or FI-X3HL(JAE) Note (3) Mating FFC Cable Connector Part No (P-TWO) or JF5X3-(JAE) Note (4) The first pixel is odd. Note (5) Input signal of even and odd clock should be the same timing.

15 , (odd),2 2, 2,2 3,,3 (even) (odd),4 (even) Pitch,Xmax Pitch Ymax, Ymax, Xmax

16 5.3 BLOCK DIAGRAM OF INTERFACE CN PRODUCT SPECIFICATION ARx- ARx+ ARx- ARx+ ER-ER7 EG-EG7 ARx2- ARx2+ EB-EB7 DE ACLK- OR-OR7 ACLK+ OG-OG7 ARx3- ARx3+ PLL OB-OB7 DCLK BRx- BRx+ BRx- BRx+ BRx2- BRx2+ BCLK- BCLK+ BRx3- BRx3+ PLL Timing Controller From 液晶之家

17 ER~ER7 Even pixel R data OR~OR7 Odd pixel R data EG~EG7 Even pixel G data OG~OG7 Odd pixel G data EB~EB7 Even pixel B data OB~OB7 Odd pixel B data DE Data enable signal DCLK Data clock signal Note () The system must have the transmitter to drive the module. Note (2) LVDS cable impedance shall be 5 ohms per signal line or about ohms per twist-pair line when it is used differentially. Note (3) Two pixel data send into the module for every clock cycle. The first pixel of the frame is odd pixel and the second pixel is even pixel. 5.4 LVDS INTERFACE VESA Format Current RXCLK RXCLK ORX ORX G R5 R4 R3 R2 R R ORX ORX B B G5 G4 G3 G2 G ORX2 ORX2 DE VS HS B5 B4 B3 B2 ORX3 ORX3 RSVD B7 B6 G7 G6 R7 R6 ERX ERX G R5 R4 R3 R2 R R ERX ERX B B G5 G4 G3 G2 G ERX2 ERX2 DE VS HS B5 B4 B3 B2 ERX3 ERX3 RSVD B7 B6 G7 G6 R7 R6 R~R7 Pixel R Data (7; MSB, ; LSB) G~G7 Pixel G Data (7; MSB, ; LSB) B~B7 Pixel B Data (7; MSB, ; LSB) DE Data enable signal DCLK Data clock signal HS H-Sync signal VS V-Sync signal Notes () RSVD (reserved) pins on the transmitter shall be H or L.

18 5.5 COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R7 R6 R5 R4 R3 R2 R R G7 G6 G5 G4 G3 G2 G G B7 B6 B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red() / Dark Red() Red(2) Red(253) Red(254) Red(255) Gray Scale Of Green Green() / Dark Green() Green(2) Green(253) Green(254) Green(255) Gray Scale Of Blue Blue() / Dark Blue() Blue(2) Blue(253) Blue(254) Blue(255) Note () Low Level Voltage, High Level Voltage From 液晶之家

19 6. INTERFACE TIMING 6. INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. (Ta = 25 ± 2 ºC) Signal Item Symbol Min. Typ. Max. Unit Note LVDS Receiver Clock Frequency F clkin (=/TC) MHz Period Tc 3.47 ns Input cycle to Cycle jitter Spread spectrum modulation range Spread spectrum modulation frequency T rcl -.2*Tc.2*Tc ps (2) Fclkin_mod.97* F clkin.3*f clkin MHz F SSM 2 KHz LVDS Setup Time Tlvsu 6 ps Receiver Data Hold Time Tlvhd 6 ps (3) Vertical Active Display Term Horizontal Active Display Term Frame Rate F r Hz Total Tv Th Tv=Tvd+Tvb Display Tvd Th Blank Tvb Th Total Th 5 5 Tc Th=Thd+Thb Display Thd Tc Blank Thb Tc Note Because this module is operated by DE only mode, Hsync and Vsync input signals are ignored. INPUT SIGNAL TIMING DIAGRAM

20 Note () Please make sure the range of frame rate has follow the below equation Fr(max) Fclkin Tv Th Fr(min) Note (2) The input clock cycle-to-cycle jitter is defined as below figures. Trcl = I T TI Note (3) The SSCG (Spread spectrum clock generator) is defined as below figures.

21 6.2 POWER ON/OFF SEQUENCE (Ta = 25 ± 2 ºC) To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the diagram below. Timing Specifications Parameters Values Min Typ. Max Units T.5 -- ms T ms T ms T ms T ms T ms T ms Note () The supply voltage of the external system for the module input should be the same as the definition of Vcc. Note (2) When the backlight turns on before the LCD operation of the LCD turns off, the display may momentarily become abnormal screen. Note (3) In case of VCC = off level, please keep the level of input signals on the low or keep a high impedance. Note (4) T7 should be measured after the module has been fully discharged between power off and on period. Note (5) Interface signal shall not be kept at high impedance when the power is on. Note (6) CMI won t take any responsibility for the products which are damaged by the customers not following the Power Sequence. Note (7) There might be slight electronic noise when LCD is turned off (even backlight unit is also off). To avoid this symptom, we suggest "Vcc falling timing" to follow "T6 spec". From 液晶之家

22 7. OPTICAL CHARACTERISTICS 7. TEST CONDITIONS PRODUCT SPECIFICATION Item Symbol Value Unit Ambient Temperature Ta 252 oc Ambient Humidity Ha 5 %RH Supply Voltage VCC 5 V Input Signal LED Light Bar Input Current Per Input Pin According to typical value in "3. ELECTRICAL CHARACTERISTICS" I PIN 65±.95 ma DC PWM Duty Ratio D % LED Light Bar Test Converter CMI 35-D65452 The LCD module should be stabilized at given temperature for hour to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting backlight for hour in a windless room.

23 7.2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown in 7.2. The following items should be measured under the test conditions described in 7. and stable environment shown in 7.. Item Symbol Condition Min. Typ. Max. Unit Note Contrast Ratio CR Note (2) Response Time T R T F ms Note (3) Center Luminance of White LC cd/m 2 Note (5) White Variation W % Note (7) Cross Talk CT % Note (6) Color Chromaticity Red Green Blue Rx Ry x=, y = Viewing angle at normal direction Gx.32 - Gy Typ..622 Typ. - Bx By.52 - ()(4) White Wx Wy Color Gamut C.G % NTSC Viewing Angle Horizontal x + + x - CR Vertical Y ++ Y - USB Horizontal x + + x - CR Vertical Y ++ Y - USB Deg. ()(4)

24 Note () Definition of Viewing Angle (x, y) PRODUCT SPECIFICATION Viewing angles are measured by Autronic Conoscope Cono-8 Normal x = y = y- y X- = 9 x- x x y+ 2 o clock direction y+ = 9 6 o clock y- = 9 y- x+ X+ = 9 Note (2) Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = Surface Luminance with all white pixels Surface Luminance with all black pixels CR = CR (5), where CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note(7). Note (3) Definition of Response Time (T R, T F ) % 9% Gray Level 255 Gray Level 255 Optical Response Gray Level % % Time T R T F 66.67ms 66.67ms From 液晶之家

25 Note (4) Measurement Setup PRODUCT SPECIFICATION The LCD module should be stabilized at given temperature for hour to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting backlight for hour in a windless room. LCD M odule LCD P anel CS-2T - or equivalent 5 mm Light Shield Room (Ambient Luminance < 2 lux) Note (5) Definition of Luminance of White (L C, L AVE ) Measure the luminance of gray level 255 at center point and 5 points L C = L (5), where L (X) is corresponding to the luminance of the point X at the figure in Note (7). Note (6) Definition of Cross Talk (CT) CT = YB YA / YA (%) Where YA = Luminance of measured location without gray level pattern (cd/m2) YB = Luminance of measured location with gray level pattern (cd/m2) (, ) Active Area (, ) Active Area Y A, U (D/2,W/8) Y B, U (D/2,W/8) Y A, L (D/8,W/2) Gray 28 Y A, R (7D/8,W/2) Y B, L (D/8,W/2) Gray Y B, R (7D/8,W/2) Y A, D (D/2,7W/8) (D, W) Y B, D (D/2,7W/8) (D, W)

26 Note (7) Definition of White Variation (W) Measure the luminance of gray level 255 at 9 points PRODUCT SPECIFICATION W = Minimum [L () ~ L (9)] / Maximum [L () ~ L (9)] From 液晶之家

27 8. PRECAUTIONS 8. ASSEMBLY AND HANDLING PRECAUTIONS [ ] Do not apply rough force such as bending or twisting to the module during assembly. [ 2 ] It is recommended to assemble or to install a module into the user s system in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. [ 3 ] Do not apply pressure or impulse to the module to prevent the damage of LCD panel and Backlight. [ 4 ] Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the damage and latch-up of the CMIS LSI chips. [ 5 ] Bezel of Set can not press or touch the panel surface. It will make light leakage or scrape. [ 6 ] Do not plug in or pull out the I/F connector while the module is in operation. [ 7 ] Do not disassemble the module. [ 8 ] Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. [ 9 ] Moisture can easily penetrate into LCD module and may cause the damage during operation. [ ] When storing modules as spares for a long time, the following precaution is necessary. [. ] Do not leave the module in high temperature, and high humidity for a long time. It is highly recommended to store the module with temperature from to 35at normal humidity without condensation. [.2 ] The module shall be stored in dark place. Do not store the TFT-LCD module in direct sunlight or fluorescent light. 8.2 SAFETY PRECAUTIONS [ ] If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. [ 2 ] After the module s end of life, it is not harmful in case of normal operation and storage. 8.3 SAFETY REVIEW 8.3. SAFETY STANDARDS The LCD module should be certified with safety regulations as follows Requirement Standard Remark UL UL or Ed.227 UL665 Ed.727 cul/csa CAN/CSA C22.2 No or CAN/CSA C22.2 No A26 CB IEC / EN A29 IEC6652+ A25 / EN A26 + A28

28 9. DEFINITION OF LABELS 9. CMI MODULE LABEL The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. V236H-LE6 Rev. XX X X X X X X X Y M D L N N N N E27943 MADE IN TAIWAN GEMN RoHS V236H-LE6 Rev. XX XXXXXXXYMDLNNNN MADE IN CHINA LEOO(or CAPG or CANO) RoHS Model Name V236H LE6 Revision Rev. XX, for example A, A B, B2 or C, C2 etc. Serial ID X X X X X X X Y M D L N N N N Serial No. Product Line Year, Month, Date CMI Internal Use CMI Internal Use Revision Serial ID includes the information as below CMI Internal Use Manufactured Date Year 2=, 22=2, 23=3, 24=4 2=, 2=, 22=2 Month ~9, A~C, for Jan. ~ Dec. Day ~9, A~Y, for st to 3st, exclude I,O, and U. Revision Code Cover all the change Serial No. Manufacturing sequence of product Product Line Line, 2 Line 2, etc.

29 . PACKAGING. PACKING SPECIFICATIONS () LCD modules / Box (2) Box dimensions 62(L) X 348(W) X 43(H) mm (3) Weight approximately 3.kg ( modules per box) PRODUCT SPECIFICATION.2 PACKAGING METHOD () Carton Packing should have no failure in the following reliability test items. Test Item Test Conditions Note Vibration ISTA STANDARD Random, Frequency Range 2 Hz Top & Bottom 3 minutes (+Z), min (-Z), Non Operation Right & Left minutes (X) Back & Forth minutes (Y) Dropping Test Corner, 3 Edge, 6 Face, 3cm Non Operation Figure - packing method

30 For ocean shipping Sea / Land Transportation (4ft HQ Container) Sea / Land Transportation (4ft/2ft Container) Corner Protector (5*5*mm) PP Belt PE Sheet Corner Protector (5*5*mm) PP Belt Film Corner Protector (5*5*8mm) PE Sheet Film Corner Protector (5*5*8mm) PE Sheet Film Corner Protector (5*5*25mm) Film PE Sheet Corner Protector (5*5*8mm) Pallet (25*5*43mm) Pallet (25*5*43mm) Carton label Carton label For air transport PP Belt Corner Protector (5*5*mm) PE Sheet Corner Protector (5*5*25mm) Film Pallet (25*5*43mm) Carton label Figure -2 packing method

31 From 液晶之家

32 From 液晶之家 CHIMEI

MODEL NO.: V236BJ1 SUFFIX: LE2

MODEL NO.: V236BJ1 SUFFIX: LE2 Tentative Specification Preliminary Specification Approval Specification MODEL NO. V236BJ SUFFIX LE2 Customer APPROVED BY SIGNATURE Name / Title Note Please return copy for your confirmation with your