TFT LCD Approval Specification MODEL NO.: V260H1 P03

Size: px

Start display at page:

Download "TFT LCD Approval Specification MODEL NO.: V260H1 P03"

Nancy Merritt
5 years ago
Views:

1 Issued Date 23, Jul. 2 Model No. V26H P3 TFT LCD Specification MODEL NO. V26H P3 Customer Approved by Note Approved By TV Product Marketing & Management Div Chao-Chun Chung Reviewed By QA Dept. Hsin-Nan Chen Product Development Div. TC Pan Prepared By LCD TV Marketing and Product Management Div. Vincent Chou Delia Lin Version 2.

2 Issued Date 23, Jul. 2 Model No. V26H P3 - CONTENTS - REVISION HISTORY GENERAL DESCRIPTION OVERVIEW.2 CHARACTERISTICS.3 MECHANICAL SPECIFICATIONS 2. ABSOLUTE MAXIMUM RATINGS ABSOLUTE RATINGS OF ENVIRONMENT (BASED ON CMI MODULE V26H-L3) 2.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL) 2.3 ELECTRICAL ABSOLUTE RATINGS (OPEN CELL) 3. ELECTRICAL CHARACTERISTICS TFT LCD OPEN CELL 4. BLOCK DIAGRAM TFT LCD MODULE 5. INPUT TERMINAL PIN ASSIGNMENT TFT LCD MODULE 5.2 BLOCK DIAGRAM OF INTERFACE 5.3 LVDS INTERFACE 5.4 COLOR DATA INPUT ASSIGNMENT 6. INTERFACE TIMING INPUT SIGNAL TIMING SPECIFICATIONS 6.2 POWER ON/OFF SEQUENCE 7. OPTICAL CHARACTERISTICS TEST CONDITIONS 7.2 OPTICAL SPECIFICATIONS 8. DEFINITION OF LABELS CMI OPEN CELL LABEL 8.. FOR TAINAN LCM, NAN-HAI LCM, NINGBO LCM s LABEL TYPE 8..2 FOR JHUNAN T2 LCM s LABEL TYPE 8.2 CARTON LABEL 8.2. FOR TAINAN LCM, NAN-HAI LCM, NINGBO LCM s CARTON LABEL TYPE FOR JHUNAN T2 LCM s CARTON LABEL TYPE 9. PACKAGING PACKING SPECIFICATIONS 9.2 PACKING METHOD. PRECAUTIONS ASSEMBLY AND HANDLING PRECAUTIONS.2 SAFETY PRECAUTIONS. MECHANICAL CHARACTERISTICS Version 2.

3 Issued Date 23, Jul. 2 Model No. V26H P3 REVISION HISTORY Version Date Page (New) Section Description Ver 2. Feb., All All Specification was first issued. Ver 2. Jul. 23, 25~27 8 Add T2 LCM label information. 3 Modify the drawing of mechanical. 3 Version 2.

4 Issued Date 23, Jul. 2 Model No. V26H P3. GENERAL DESCRIPTION. OVERVIEW V26H- P3 is a 26-inch TFT LCD cell with driver ICs and 2ch-LVDS interface. This module supports 92 x 8 Full HDTV format and can display 6.7M colors (8-bit/color). The backlight unit is not built in.2 CHARACTERISTICS CHARACTERISTICS ITEMS SPECIFICATIONS Screen Diagonal [in] 26. Pixels [lines] 92 x 8 Active Area [mm] Sub -Pixel Pitch [mm] 576 x 324. (H).3(V) Pixel Arrangement RGB vertical stripe Weight [g] TYP. 865 Physical Size [mm] 592(W) x 339.8(H) x.83(d) Typ. Display Mode TN, Normally White Contrast Ratio 8 Typ. (Typical value measured at CMI s module) Glass thickness (Array/CF) [mm].7 /.7 Viewing Angle (CR>) +8/-8(H), +8/-7(V) Typ. (Typical value measured at CMI s module) Color Chromaticity R=.654,.329 G=.275,.6 B=.47,.6 W=.32,.365 *Please refer to color chromaticity on p.2 Cell Transparency [ ] Polarizer (CF side) Polarizer (TFT side) 6.% Typ. (Typical value measured at CMI s module) Anti-Glare coating, 587.4(W) x 335.2(H). Hardness 3H 587.4(W) x 335.2(H).3 MECHANICAL SPECIFICATIONS Item Min. Typ. Max. Unit Note Weight 865 g The mounting inclination of the connector makes I/F connector mounting position () the screen center within ±.5mm as the horizontal. Note () Connector mounting position +/-.5mm 4 Version 2.

5 Issued Date 23, Jul. 2 Model No. V26H P3 2. ABSOLUTE MAXIMUM RATINGS 2. ABSOLUTE RATINGS OF ENVIRONMENT (BASED ON CMI MODULE V26H-L3) Item Symbol Value Min. Max. Unit Note Storage Temperature T ST ºC () Operating Ambient Temperature T OP +5 ºC (), (2) Note () Temperature and relative humidity range is shown in the figure below. (a) 9 %RH Max. (Ta 4 ºC). (b) Wet-bulb temperature should be 39 ºC Max. (Ta > 4 ºC). (c) No condensation. Note (2) The maximum operating temperature is based on the test condition that the surface temperature of display area is less than or equal to 65 ºC with LCD module alone in a temperature controlled chamber. Thermal management should be considered in final product design to prevent the surface temperature of display area from being over 65 ºC. The range of operating temperature may degrade in case of improper thermal management in final product design. Relative Humidity (%RH) Operating Range 4 2 Storage Range Temperature (ºC) 5 Version 2.

6 Issued Date 23, Jul. 2 Model No. V26H P3 2.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL) Storage Condition With shipping package. Storage temperature range 25±5 Storage humidity range 5±%RH Shelf life a month 2.3 ELECTRICAL ABSOLUTE RATINGS 2.3. ELECTRICAL ABSOLUTE RATINGS (OPEN CELL) Item Symbol Value Min. Max. Unit Power Supply Voltage Vcc V Input Signal Voltage VIN V Note () Note () Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. 6 Version 2.

7 Issued Date 23, Jul. 2 Model No. V26H P3 3. ELECTRICAL CHARACTERISTICS 3. TFT LCD MODULE Ta = 25 ± 2 ºC Parameter Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage V CC V () Rush Current I RUSH 3. A (2) White Pattern.29 A Power Supply Current Horizontal Stripe.45 A (3) LVDS interface CMOS Differential Input High Threshold Voltage Differential Input Low Threshold Voltage Black Pattern A V LVTH + mv V LVTL - mv Common Input Voltage V CM..2.4 V Differential input voltage V ID 2 6 mv Terminating Resistor R T ohm Input High Threshold Voltage V IH V (4) interface Input Low Threshold Voltage V IL.7 V Note () The module should be always operated within above ranges. Note (2) Measurement Conditions +2.V Q AO449 FUSE C3 Vcc (LCD Module Input) R uf 2K VR 47K (Low to High) (Control Signal) SW R2 K Q2 2N72 C uf 7 Version 2.

= 2 V, Ta = 25 ± 2 ºC, f v = 6 Hz, whereas a power dissipation check pattern below is

8 Issued Date 23, Jul. 2 Model No. V26H P3 Vcc rising time is 47us +2V.9Vcc.Vcc GND 47us Note (3) The specified power supply current is under the conditions at Vcc = 2 V, Ta = 25 ± 2 ºC, f v = 6 Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern Active Area Active Area c. Horizontal Pattern 8 Version 2.

9 Issued Date 23, Jul. 2 Model No. V26H P3 Note (4) The LVDS input characteristics are as follows 4. BLOCK DIAGRAM 4. TFT LCD MODULE TFT LCD PANEL (92x3x8) BACKLIGHT UNIT CONNECTOR CP44S(CviLux) X BOARD LVDS SIGNAL INPUT Connector Part No. Starconn, 7C5-RA-G4 or compatible 9 Version 2.

10 Issued Date 23, Jul. 2 Model No. V26H P3 5. INPUT TERMINAL PIN ASSIGNMENT 5. TFT LCD MODULE CNF Connector Pin Assignment Pin Name Description Note VCC +2V power supply 2 VCC +2V power supply 3 VCC +2V power supply 4 VCC +2V power supply 5 VCC +2V power supply 6 GND Ground 7 GND Ground 8 GND Ground 9 GND Ground ORX- Odd pixel Negative LVDS differential data input. Channel ORX+ Odd pixel Positive LVDS differential data input. Channel 2 ORX- Odd pixel Negative LVDS differential data input. Channel 3 ORX+ Odd pixel Positive LVDS differential data input. Channel () 4 ORX2- Odd pixel Negative LVDS differential data input. Channel 2 5 ORX2+ Odd pixel Positive LVDS differential data input. Channel 2 6 GND Ground 7 OCLK- Odd pixel Negative LVDS differential clock input 8 OCLK+ Odd pixel Positive LVDS differential clock input. () 9 GND Ground 2 ORX3- Odd pixel Negative LVDS differential data input. Channel 3 2 ORX3+ Odd pixel Positive LVDS differential data input. Channel 3 () 22 N.C. No Connection 23 N.C. No Connection (3) 24 GND Ground 25 ERX- Even pixel Negative LVDS differential data input. Channel 26 ERX+ Even pixel Positive LVDS differential data input. Channel 27 ERX- Even pixel Negative LVDS differential data input. Channel 28 ERX+ Even pixel Positive LVDS differential data input. Channel () 29 ERX2- Even pixel Negative LVDS differential data input. Channel 2 3 ERX2+ Even pixel Positive LVDS differential data input. Channel 2 3 GND Ground 32 ECLK- Even pixel Negative LVDS differential clock input. 33 ECLK+ Even pixel Positive LVDS differential clock input. () Version 2.

11 Issued Date 23, Jul. 2 Model No. V26H P3 34 GND Ground 35 ERX3- Even pixel Negative LVDS differential data input. Channel 3 36 ERX3+ Even pixel Positive LVDS differential data input. Channel 3 () 37 N.C. No Connection 38 N.C. No Connection (3) 39 GND Ground 4 N.C. No Connection 4 N.C. No Connection 42 N.C. No Connection (3) 43 N.C. No Connection 44 N.C. No Connection 45 SELLVDS High(3.3V) or open for VESA, Low (GND) for JEIDA (4)(5) 46 N.C. No Connection 47 N.C. No Connection 48 N.C. No Connection 49 N.C. No Connection (3) 5 N.C. No Connection 5 N.C. No Connection Note () Two pixel data send into the module for every clock cycle. The first pixel of the frame is odd pixel and the second pixel is even pixel Note (2) LVDS connector pin order defined as follows Note (3) Reserved for internal use. Please leave it open. Note (4) Low JEIDA LVDS Format (Connect to GND), High or open VESA Format. (Connect to +3.3V) Version 2.

12 Issued Date 23, Jul. 2 Model No. V26H P3 Note (5) LVDS signal pin connected to the LCM side has the following diagram. R in the system side should be less than K Ohm. (R < K Ohm) Vcc Selector (pin45) R R2 R3 Setting TCON System side LCM side 2 Version 2.

13 Issued Date 23, Jul. 2 Model No. V26H P3 5.2 BLOCK DIAGRAM OF INTERFACE CNF ER-ER7 EG-EG7 EB-EB7 DE OR-OR7 OG-OG7 OB-OB7 DCLK Host TxIN PLL ERx+ ERx- ERx+ ERx- ERx2+ ERx2- ERx3+ ERx3- ECLK+ ECLK- pf pf pf pf pf PLL RxOUT ER-ER7 EG-EG7 EB-EB7 DE OR-OR7 OG-OG7 OB-OB7 DCLK Graphics Controller ORx+ ORx- ORx+ pf Timing Controller ORx- pf ORx2+ ORx2- ORx3+ ORx3- pf pf PLL OCLK+ OCLK- pf PLL LVDS Transmitter THC63LVDM83A (LVDF83A) LVDS Receiver 3 Version 2.

14 Issued Date 23, Jul. 2 Model No. V26H P3 ER~ER7 Even pixel R data EG~EG7 Even pixel G data EB~EB7 Even pixel B data OR~OR7 Odd pixel R data OG~OG7 Odd pixel G data OB~OB7 Odd pixel B data DE Data enable signal DCLK Data clock signal Note () The system must have the transmitter to drive the module. Note (2) LVDS cable impedance shall be 5 ohms per signal line or about ohms per twist-pair line when it is used differentially. Note (3) Two pixel data send into the module for every clock cycle. The first pixel of the frame is odd pixel and the second pixel is even pixel. 4 Version 2.

15 Issued Date 23, Jul. 2 Model No. V26H P3 5.3 LVDS INTERFACE VESA LVDS format (SELLVDS pin=h or open) Current RXCLK ORX G R5 R4 R3 R2 R R ORX B B G5 G4 G3 G2 G ORX2 DE VS HS B5 B4 B3 B2 ORX3 RSVD B7 B6 G7 G6 R7 R6 ERX G R5 R4 R3 R2 R R ERX B B G5 G4 G3 G2 G ERX2 DE VS HS B5 B4 B3 B2 ERX3 RSVD B7 B6 G7 G6 R7 R6 JEDIA LVDS format (SELLVDS pin=l) Current RXCLK ORX G2 R7 R6 R5 R4 R3 R2 ORX B3 B2 G7 G6 G5 G4 G3 ORX2 DE VS HS B7 B6 B5 B4 ORX3 RSVD B B G G R R ERX G2 R7 R6 R5 R4 R3 R2 ERX B3 B2 G7 G6 G5 G4 G3 ERX2 DE VS HS B7 B6 B5 B4 ERX3 RSVD B B G G R R R~R7 Pixel R Data (7; MSB, ; LSB) G~G7 Pixel G Data (7; MSB, ; LSB) B~B7 Pixel B Data (7; MSB, ; LSB) DE Data enable signal DCLK Data clock signal Notes () RSVD (reserved) pins on the transmitter shall be H or L. 5 Version 2.

16 Issued Date 23, Jul. 2 Model No. V26H P3 Version COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R7 R6 R5 R4 R3 R2 R R G7 G6 G5 G4 G3 G2 G G B7 B6 B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red() / Dark Red() Red(2) Red(253) Red(254) Red(255) Gray Scale Of Green Green() / Dark Green() Green(2) Green(253) Green(254) Green(255) Gray Scale Of Blue Blue() / Dark Blue() Blue(2) Blue(253) Blue(254) Blue(255) Note () Low Level Voltage, High Level Voltage

17 Issued Date 23, Jul. 2 Model No. V26H P3 6. INTERFACE TIMING 6. INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note Frequency F clkin (=/TC) MHz LVDS Receiver Clock Input cycle to cycle jitter Spread spectrum modulation range Spread spectrum modulation frequency T rcl 2 ps (3) Fclkin_mo d F clkin -2% F clkin +2% MHz (4) F SSM 2 KHz LVDS Receiver Data Setup Time Tlvsu 6 ps Hold Time Tlvhd 6 ps (5) Vertical Active Display Term Frame Rate F r Hz F r Hz Total Tv Th Tv=Tvd+Tvb Display Tvd Th Blank Tvb Th Horizontal Total Th 5 5 Tc Th=Thd+Thb Active Display Term Display Blank Thd Thb Tc Tc Note () Please make sure the range of pixel clock has follow the below equation Fclkin(max) Fr6 Tv Th Fr5 Tv Th Fclkin(min) Note (2) This module is operated in DE only mode and please follow the input signal timing diagram below 7 Version 2.

18 Issued Date 23, Jul. 2 Model No. V26H P3 INPUT SIGNAL TIMING DIAGRAM Tv Tvd Tvb DE Th DCLK DE Tc Thb Thd DATA Valid Display Data (96 clocks) Note (3) The input clock cycle-to-cycle jitter is defined as below figures. Trcl = I T TI 8 Version 2.

19 Issued Date 23, Jul. 2 Model No. V26H P3 Note (4) The SSCG (Spread spectrum clock generator) is defined as below figures. Note (5) The LVDS timing diagram and setup/hold time is defined and showing as the following figures. LVDS RECEIVER INTERFACE TIMING DIAGRAM Tc RXCLK+/- RXn+/- Tlvsu Tlvhd T 4 3T 4 5T 4 7T 4 9T 4 T 4 3T 4 9 Version 2.

20 Issued Date 23, Jul. 2 Model No. V26H P3 6.2 POWER ON/OFF SEQUENCE To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the diagram below..9vcc.9vcc V.VCC.Vcc.5 T ms T2 5ms T3 5ms 5ms T4 T T2 T3 T4 LVDS Signals V Power On VALID Power Off T7 T2 T8 T3 T7 T8 Option Signals (SELLVDS) Backlight (Recommended) 5ms T5 ms T6 5% 5% T5 T6 Power ON/OFF Sequence Note () The supply voltage of the external system for the module input should follow the definition of Vcc. Note (2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD operation or the LCD turns off before the backlight turns off, the display may momentarily become abnormal screen. Note (3) In case of Vcc is in off level, please keep the level of input signals on the low or high impedance. If T2<,that maybe cause electrical overstress failure. Note (4) T4 should be measured after the module has been fully discharged between power off and on period. Note (5) Interface signal shall not be kept at high impedance when the power is on. 2 Version 2.

21 Issued Date 23, Jul. 2 Model No. V26H P3 7. OPTICAL CHARACTERISTICS 7. TEST CONDITIONS Item Symbol Value Unit Ambient Temperature Ta 25±2 o C Ambient Humidity Ha 5± %RH Supply Voltage V CC 2. V Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS" Lamp Current I L 7.5 ±.5 ma Oscillating Frequency (Inverter) F W 4 ± 3 KHz Vertical Frame Rate Fr 6 Hz 7.2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown as below. The following items should be measured under the test conditions described in 7. and stable environment shown in Note (5). Item Symbol Condition Min. Typ. Max. Unit Note Red Rcx Rcy Gcx θ x =, θ Y = Green Color Gcy Viewing Angle at Normal Chromaticity Bcx Direction.47 - Blue Bcy Standard light source C.6 - (),(5) White Wcx.32 - Wcy Center Transmittance T% θ x =, θ Y = % (),(7) Contrast Ratio CR with CMI module 8 - (),(3) Response Time White Variation Horizontal Viewing Angle Vertical T R θ x =, θ Y = -.4 ms T F with CMI Module@6Hz ms (),(4) δw θ x =, θ Y = with CMI module (),(6) θ x + 8 θ x - CR 8 θ Y + With CMI module 8 Deg. (),(2) θ Y Version 2.

22 Issued Date 23, Jul. 2 Model No. V26H P3 Note () Light source is the standard light source C which is defined by CIE and driving voltage are based on suitable gamma voltages. The calculating method is as following. Measure Module s and BLU s spectrum. White is without signal input and R,G,B are with signal input. BLU (for V26H-L3) is supplied by CMI. 2. Calculate cell s spectrum. 3. Calculate cell s chromaticity by using the spectrum of standard light source C. Note () Light source is the BLU which is supplied by CMI and driving voltage are based on suitable gamma voltages. Note (2) Definition of Viewing Angle (θx, θy) Viewing angles are measured by Autronic Conoscope Cono-8 Normal θx = θy = º θy- θy+ θx- = 9º x- θx θx+ y+ 2 o clock direction θy+ = 9º 6 o clock θy- = 9º y- x+ θx+ = 9º Note (3) Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L L255 Luminance of gray level 255 L Luminance of gray level CR = CR (5), where CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note (6). 22 Version 2.

23 Issued Date 23, Jul. 2 Model No. V26H P3 Note (4) Definition of Response Time (T R, T F ) Gray Level 255 Gray Level 255 % 9% Optical Response Gray Level % % T R T F Time Note (5) Measurement Setup The LCD module should be stabilized at given temperature for hour to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement (CS- or CA-2 calibrated by CS-2) should be executed after lighting backlight for hour in a windless room. LCD Module LCD Panel CS-2 Field of View = º 5 mm Light Shield Room (Ambient Luminance < 2 lux) 23 Version 2.

24 Issued Date 23, Jul. 2 Model No. V26H P3 Note (6) Definition of White Variation (δw) Measure the luminance of gray level 255 at 5 points δw = Maximum [L (), L (2), L (3), L (4), L (5)] / Minimum [L (), L (2), L (3), L (4), L (5)] Horizontal Line D D/4 D/2 3D/4 Vertical Line W W/4 W/2 2 5 X Test Point X= to 5 3W/4 3 4 Note (7) Definition of Transmittance (T%) Module is without signal input. Active Area Luminance of LCD module Transmittance = * % Luminance of backlight 24 Version 2.

25 Issued Date 23, Jul. 2 Model No. V26H P3 8. DEFINITION OF LABELS 8. OPEN CELL LABEL The barcode nameplate is pasted on each open cell as illustration for CMI internal control. 8.. FOR TAINAN LCM, NAN-HAI LCM, NINGBO LCM s LABEL TYPE V26H-P3 V26H-P3 Rev. XXXXXXXXXXXXXX XXXXXXXXXXXXXX 8..2 FOR JHUNAN T2 LCM s LABEL TYPE 73 mm V26H-P3 Rev.XX AT26XXXXX xx 8 mm Z Z 2 Z 3 Z 4 Z 5 Z 6--Z 7--Z 8 Z 9 Z Z Z 2 Z 'Z 2'-Z 3' Z 4'Z 5'Z 6'Z 7'-Z 8' - Z 9 '- Z '- Z ' Z 2'-Z 3'-Z 4' Z 5' -Z 6 '-Z 7 'Z 8' Z 9' -Z 2'Z 2'Z 22 ' Z 23 ' MADE IN XXX (a). Model Number V26H-P3 (b). Rev. XX (c). Serial ID I Z Z 2 Z 3 Z 4 Z 5 Z 6 Z 7 Z 8 Z 9 Z Z Z 2 Serial No CMI internal use CMI internal use CMI internal use Year, Month, Date CMI internal use Serial ID includes the information as below. Manufactured Date Year ~9, for 2~29 2. Month ~9 & A~C for Jan. ~ Dec. 3. Date ~9 & A~Z (exclude I, O, Q, U) for st~3th 4. Serial No Module manufacture sequence no 25 Version 2.

26 Issued Date 23, Jul. 2 Model No. V26H P3 8.2 CARTON LABEL The barcode nameplate is pasted on each box as illustration, and its definitions are as following explanation 8.2. FOR TAINAN LCM, NAN-HAI LCM, NINGBO LCM s CARTON LABEL TYPE P.O. NO. Parts ID. Carton ID. Quantities 2 XXXXXXXXXXXXXX Made in XXXXXX (a) Model Name V26H P3 (b) Carton ID CMI internal control (c) Quantities 2 26 Version 2.

27 Issued Date 23, Jul. 2 Model No. V26H P FOR JHUNAN T2 LCM s CARTON LABEL TYPE BOX ID INNOLUX DISPLAY 6 mm Z Z 2 Z 3 Z 4 --Z 5--Z 6 Z 7 Z 8 Z 9 Model No. V26H-P3 Rev. XX AT26XXXXXX XXX Quantity 2 PCS MFG Date 2XX/XX/XX QC Made in XXX mm (a). Model Number V26H-P3 (b). Rev. XX (c). Packing quantity 2 PCS (d). Serial ID Z Z 2 Z 3 Z 4 Z 5 Z 6 Z 7 Z 8 Z 9 Serial No CMI internal use Year, Month, Date CMI internal use Serial ID includes the information as below (a). Manufactured Date Year ~9, for 2 ~29 Month ~9 & A~C for Jan. ~ Dec. Date ~9 & A~Z (exclude I, O, Q, U) for st~3th (b). Serial No Module packing sequence no. 27 Version 2.

28 Issued Date 23, Jul. 2 Model No. V26H P3 9. PACKAGING 9. PACKING SPECIFICATIONS () 2PCS LCD TV Panels / Box (2) Box dimensions 82 (L) X 572 (W) X 277 (H) (3) Weight approximately 27.5 Kg 9.2 PACKING METHOD Figures 9- and 9-2 are the packing method Figure. 9- packing method 28 Version 2.

29 Issued Date 23, Jul. 2 Model No. V26H P3 Figure. 9-2 packing method 29 Version 2.

30 Issued Date 23, Jul. 2 Model No. V26H P3. PRECAUTIONS. ASSEMBLY AND HANDLING PRECAUTIONS () Do not apply rough force such as bending or twisting to the product during assembly. (2) To assemble backlight or install module into user s system can be only in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) It s not permitted to have pressure or impulse on the module because the LCD panel will be damaged. (4) Always follow the correct power sequence when the product is connecting and operating. This can prevent damage to the CMOS LSI chips during latch-up. (5) Do not pull the I/F connector in or out while the module is operating. (6) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (7) It is dangerous that moisture come into or contacted the product, because moisture may damage the product when it is operating. (8) High temperature or humidity may reduce the performance of module. Please store this product within the specified storage conditions. (9) When ambient temperature is lower than ºC may reduce the display quality. For example, the response time will become slowly..2 SAFETY PRECAUTIONS () If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (2) After the product s end of life, it is not harmful in case of normal operation and storage. 3 Version 2.

31 Issued Date 23, Jul. 2 Model No. V26H P3. MECHANICAL CHARACTERISTICS CHI MEI 3 Version 2.

MODEL NO.: V185BJ1 SUFFIX: PE1

MODEL NO.: V185BJ1 SUFFIX: PE1 Tentative Specification Preliminary Specification Approval Specification MODEL NO. V85BJ SUFFIX PE Customer APPROVED BY SIGNATURE Name / Title Note Please return copy for your confirmation with your signature