Remote I/O. Remote I/O

Transcription

1 Remote I/O Active Ethernet I/O Efficient and Intelligent Ethernet I/O ioogik E Active Ethernet I/O ioogik E Active Ethernet I/O with DI, 8 DO ioogik E Active Ethernet I/O with 8 DI, 8 DO, 4 DIO ioogik E4 Active Ethernet I/O with 6 DI, 6 relay outputs ioogik E4 Active Ethernet I/O with 8 AI, AO ioogik E4 Active Ethernet I/O with 4 AI, configurable DIO ioogik E6 Active Ethernet I/O with 6 RTD inputs, 4 DO ioogik E6 Active Ethernet I/O with 8 TC inputs, 4 DO Remote Serial I/O Servers ioogik R Serial Romote I/O ioogik R RS-48 remote I/O with DI and 8 DO ioogik R4 RS-48 remote I/O with 8 AI and AO iomirror Peer-to-Peer I/O iomirror E Peer-to-Peer I/O iomirror E Ethernet peer-to-peer I/O with 8 DI and 8 DO CD Module for Standalone I/O DP6 CD Module Snap-on module for ioogik and iomirror products Modular Remote I/O Slice Form Factor, High Density Remote I/O ioogik 4 Remote I/O modules NA-4 Ethernet network adaptor module NA-4/4 RS- or RS-48 network adaptor modules Digital Input Modules 4, 8, or 6 channels Digital and Relay Output Modules, 4, 8, or 6 channels Analog Input Modules or 4-bit resolution Temperature Input Modules RTD and thermocouple input Analog Output Modules -bit resolution Power Modules Power expansion and distribution Accessories Remote I/O

2 Remote Monitoring Solutions Efficient and Intelligent Ethernet I/O Real-time Remote Monitoring & Alarms SCADA SNMP Software Custom Software MXIO ibrary Remote I/O > Efficient and Intelligent Ethernet I/O IP Camera iomirror VPort Video Encoder EDS-A EDS-A Turbo Ring < ms NPort Serial Device Server EDS-A Gigabit Ethernet Switch ioogik E/ E/E4 Active Ethernet I/O with DI, DO, & Relay ioogik E4/4 Active Ethernet I/O with AI & AO ioogik E6/6 Active Ethernet I/O with Temperature Input & DO iomirror E Ethernet Peer-to-Peer I/O with DI & DO ioogik R/4 Serial I/O with DI & DO, AI & AO ioogik 4 Modular I/O Server Fiber Optic Cable (BaseFX or BaseSX/X/HX/ZX) Twisted Pair Cable (/BaseT(X)) RS-48 Serial Cable info@moxa.com

3 Industrial Networking Solutions ioogik E Active Ethernet I/O New Generation I/O that Talks over Ethernet Active Ethernet I/O is a new concept that introduces proactive, condition-based reporting and control of I/O devices to the PC-based data acquisition and control field. The I/O status of an Active Ethernet I/O system can be reported automatically and controlled locally, based on user-specified conditions. This report-by-exception approach, which is new to PC-based I/O monitoring, requires far less bandwidth than traditional polling methods. Critical sensor data can be obtained immediately instead of being confined to specific points of time, as determined by the the polling intervals. This makes network communication between the host computer and Active Ethernet I/O concise and efficient, and makes data transmission times faster compared with traditional SCADA systems ( ms compared to sec). Remote I/O > ioogik E Active Ethernet I/O Why Choose Active Ethernet I/O? Click&Go for reduced configuration time ocal logic control with no learning curve, no third-party programming, and no maintenance fees Dramatic reduction in project implementation time MXIO D library for easier programming No Modbus addressing required VB and VC for Windows support Various options for Windows, WinCE, and inux platforms Four advantages to Active Ethernet I/O Saves network bandwidth compared with polling methods Off-line local control without a host Easy SNMP trap with I/O status Real-time event time stamp Built-in web console for configuration and monitoring Configure network parameters Set up the I/O Mode Monitor the I/O status and values info@moxa.com

4 Remote Monitoring Solutions The Most User-friendly I/O for Remote Monitoring and Alarm Applications Best Companion for PCs and Embedded Computers Unlike traditional remote I/O, the ioogik remote I/O server is designed for a PC environment. The CD module, Windows utility with documentation, and MXIO D library are designed especially for PC-based automation applications. Unique CD Module for PC-free Management The ioogik series of stand-alone remote I/O servers can be used with an optional, snap-on CD module for on-site management and configuration. This unique display module can display network and I/O settings, and you can change network settings to ensure speedy installation and maintenance. Remote I/O > ioogik E Active Ethernet I/O Intuitive Windows Utility ioogik remote I/O servers come with a very user-friendly Windows utility that includes remote configuration, firmware updates, and I/O testing and monitoring functions. These functions can save you many hours of installation and troubleshooting, and all settings can be saved to a file for future reference. Online Documentation In addition to providing easy-to-use utilities, ioogik remote I/O servers also come with an online wiring guide to help you troubleshoot problems easily without needing to refer to the manual. The online guide lists key features of I/O points, and displays a conversion table for analog input/output points. Remote Monitoring over TCP/IP Networks The ioogik Ethernet remote I/O Server allows you to monitor the status of all I/O connections remotely over a TCP/IP network, allowing you to save the cost and time associated with traveling to and from your remote sites info@moxa.com

5 Industrial Networking Solutions Most Applications Can Use Active Ethernet I/O Active Ethernet I/O is an ideal solution for applications in remote monitoring, data collection, asset/environment control, and notification: Server rooms for temperature and humidity control, back-up power supply initiation, and more Buildings, shopping-centers, and airports for temperature and humidity control Roadside cabinets for telecommunication/power industries Air-conditioning and heating unit supervision Tank level monitoring and pump control Door and window sensors in airports and museums Warehouse temperature and humidity control Medical storage Food and chemical industry Shopping mall visitor tracking There are many ways that Active Ethernet I/O can be used to enhance your existing applications, improve your system s cost effectiveness, or help you develop new, more powerful applications. Instant Event Reporting by Input People Counter Counter = Improves data acquisition and control system efficiency More accurate and timely measurements to prevent data loss SNMP to I/O (SNMP protocol) On/Off light Supports SNMP read/write/trap Supports I/O control using SNMP management software HP Openview/What's Up Software Instead of relying on host computers that continually poll I/O devices for data, Active Ethernet I/O servers can proactively report sensor status using TCP or UDP messages. Proactive messaging allows much faster notification of I/O events and generates much lower network and CPU loads. Message content is fully customizable, and up to simultaneous destinations are supported. Active Ethernet I/O can be configured for SNMP management of I/O control and reporting. Customized SNMP traps can be triggered by I/O events, such as turning on a light switch. SNMP software can be used for sophisticated automation, monitoring, and control of sensors and switches over Ethernet. Remote I/O > ioogik E Active Ethernet I/O ocal Alarm & I/O Control If DI_=On, Then DO_=On ocal intelliegence No programming An Active Ethernet I/O server can be used for simple output control that is triggered by input status, without a PC controller. For example, a door sensor can be configured to trigger an alarm. Configuration is done through simple If/Then statements, and no programming is required. iquid Heating System with ioogik E6 Transmit "Active Message" based on average ocal control of heater through DO channel Transmit "Active Message" based on difference of two values ocal control of stirring machine through DO channel Average (RTDRTDRTD)/ = 4 Difference RTD-RTD = 6 RTD RTD RTD DO Heater DO-Stir Machine 9 C 4 C 4 C ioogik temperature I/O brings intelligence to temperature sensors. It is equipped with virtual channels that are available for calculating the average temperature of each channel, and the difference between two physical channels. Note that a controller or PC is NOT required. info@moxa.com --

6 Remote Monitoring Solutions Wiring Examples for Active Ethernet I/O Digital Input Digital Input (Dry Contact) DI Wet Contact - Source Type DI Contact - Sink Type DI COM DI DI DI DI DI 4 DI GND DICOM DI_ DI_ DI_ GND N.C. DICOM DI_ DI_4 DI_ GND N.C. DICOM DI_ DI_ DI_ GND N.C. DICOM DI_ DI_4 DI_ GND N.C. Brown Black Blue 4 V NPN Output V - Brown Black Blue 4 V NPN Output V - Applies to these I/O models: E, E, R Digital and Relay Output Applies to these I/O models: E, E, E4, R Applies to these I/O models: E, E4 Remote I/O > ioogik E Active Ethernet I/O Digital Output DO Power DO DO DO DO DO Applies to these I/O models: 4 DO DO E, E, E4, R, E4, E6, E6 Analog Input and Output Analog Input Vin Vin - Vin Vin - Vin Vin - Vin Vin - 6 DO 7 DO GND Vin - Vin - Relay Output R_NO R_C R_NO R_C R_NO R_C R_NO R_C oads R4_NO AC/DC Power Source Applies to these I/O models: E4 Analog Output Vout Vout lout lout - Vout Vout - R4_C lout R_NO lout - R_C Applies to these I/O models: E4, E4, R4 Applies to these I/O models: E4, R4 Temperature Input RTD Input (-Wire RTD) RTD Input (-Wire RTD) Thermocouple Input EX IN IN EX IN IN EX IN IN EX IN IN EX IN IN EX IN IN EX IN IN EX IN IN EX EX EX EX EX EX EX EX EX - TC TC TC D RTD RTD RTD RTD RTD RTD RTD RTD RTD RTD RTD RTD RTD RTD RTD TC TC TC TC TC TC Applies to these I/O models: E6 Applies to these I/O models: E6 Applies to these I/O models: E info@moxa.com

7 Industrial Networking Solutions Common Specifications for ioogik Active Ethernet I/O AN Ethernet: / Mbps, RJ4 Protection:. KV magnetic isolation Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP (MIB for I/O and Network), HTTP, SNTP Serial Interface: RS-48-w: Data, Data-, GND Serial ine Protection: KV ESD for all signals Serial Communication Parameters Parity: None Data Bits: 8 Stop Bits: Flow Control: None Speed: to bps Protocol: Modbus/RTU Power Requirements Power Input: 4 VDC nominal, to 48 VDC DO Power: 4 VDC nominal, up to VDC Dimensions (unit = mm) ioogik E Series Physical Characteristics Wiring: I/O cable max. 4AWG Environmental imits Operating Temperature: - to 6 C (4 to 4 F) Storage Temperature: -4 to 8 C (-4 to 8 F) Ambient Relative Humidity: to 9% (non-condensing) Agency Approvals FCC: Part, CISPR (EN) Class A CE: IEC 6-4, IEC 6-6 Safety: U 8 Shock: IEC Freefall: IEC Vibration: IEC Warranty: years (see for details) Remote I/O > ioogik E Active Ethernet I/O Side View Front View Rear View 7..4 Selection Guide for Active Ethernet I/O I/O Input Output Model DI AI RTD TC DO Relay AO DIO E E E E E E E info@moxa.com

8 Remote Monitoring Solutions ioogik E Active Ethernet I/O with digital inputs and 8 digital outputs Instant event messaging by TCP, UDP, , SNMP trap Easy-to-use Click&Go ogic for local output control -point 4 VDC digital input with counter 8-point 4 VDC digital output with pulse output PC-based configuration utility and web console I/O control over Modbus/TCP and SNMP protocol Windows and WinCE VB/VC, and inux C API Peer-to-Peer I/O without controller Remote I/O > ioogik E The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Introduction Simple Applications without Programming The ioogik E can convert a trigger event result directly into digital alarm output. This can be set up using the ioadmin UI to define an IF-THEN ogic rule, elimintating the need to write programs for PCs or controllers. Software Event Counter Input and Pulse Output Each digital input can be independently configured for DI or event counter mode, and the output can be independently configured for DO or pulse output mode. Specifications Digital Input Inputs:, source type I/O Mode: DI or event counter (up to 9 Hz) Dry Contact: ogic : short to GND ogic : open Wet Contact: ogic : to VDC, ogic : to VDC (DI COM to DI) Common Type: points per COM Isolation: K VDC or K Vrms Digital Output Outputs: 8, sink type I/O Mode: DO or pulse output (up to Hz) On-state Voltage: 4 VDC nominal Output Current Rating: Max. ma per channel Isolation: K VDC or K Vrms Protection: Over-temperature shutdown: Min. 7 C Over-current limit: typ. 4 ma/channel Pin Assignment I/O (left to right) DI COM DI DI DI DI DI4 DI DI6 DI7 DI8 DI9 DI DI DI. GND DO.PWR DO DO DO DO DO4 DO DO6 DO7 DO.GND Ordering Information ioogik E: Active Ethernet I/O with digital inputs and 8 digital outputs DP6: CD module with 6 x text display and buttons info@moxa.com

9 Industrial Networking Solutions ioogik E Active Ethernet I/O with 8 digital inputs, 8 digital outputs, and 4 configurable DIO Selectable digital I/O combination by software Accepts PNP or NPN sensors Instant event messaging by TCP/UDP/ /SNMP trap Easy-to-use Click&Go ogic for local output control PC-based configuration utility and web console I/O control over Modbus/TCP and SNMP protocol Windows and WinCE VB/VC, and inux C APIs Peer-to-Peer I/O without controller The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Introduction Versatile Digital Input/Output Configuration The ioogik E provides system integrators with the flexibility to handle various field demands with channels that can be configured by software for input or output operation. You can configure the I/O channels to suit your needs, for combinations such as inputs/8 outputs, 8 inputs/ outputs or inputs/ outputs. Specifications Single Ethernet DIO that Accepts Types of Sensors Unlike traditional Ethernet I/O products, the ioogik E can connect to dry contact, PNP, and NPN sensors at the same time. You can choose the sensor type based on your wiring approach. Remote I/O > ioogik E Digital Input Channels: 8 fixed points Sensor Type: 6-point groups for NPN/PNP type I/O Mode: DI or Event Counter (up to 9Hz) Dry Contact: ogic : short to GND ogic : open Wet Contact: ogic : to VDC ogic : to VDC Common Type: 6 points per COM Isolation: K VDC or K Vrms ow Speed Counter/Frequency: 9 Hz, power off storage Pin Assignment Over-voltage Protection: 6 VDC Counter Memory: 48 Bytes Digital Output Channels: 8 fixed points sink, 4 VDC, ma Magnetic Isolation: K Vrms or K VDC Pulse Wave Width: ms/ Hz Over-voltage Protection: 4 VDC Over-current imit: 4 ma (typical) Over-temperature Shutdown: 7 C (min.) DI/DO Configurable Channels Channels: 4 I/O Mode: DI or Event Counter (Up to 9 Hz) DO or Pulse Output (Up to Hz) I/O (left to right) DI COM DI DI DI DI DI 4 DI DI COM DI 6 DI 7 DIO 8 DIO 9 DIO DIO GND DO DO DO DO DO 4 DO DO 6 DO 7 DO PWR Ordering Information ioogik E: Active Ethernet I/O, with 8 digital inputs, 8 digital outputs, and 4 DIOs DP6: CD module with 6 x text display and buttons info@moxa.com

10 AVAIABE IN Q Remote Monitoring Solutions ioogik E4 Active Ethernet I/O with 6 digital inputs and 6 relay outputs 6 DIs supporting PNP, NPN, and dry contact 6 form A relay outputs (normal status open) Relay specifications: A/ VAC, A/ VDC Instant event messaging by TCP, UDP, , SNMP trap Saves DI and relay counter when the power is off PC-based configuration utility and web console Power-on default relay status setting with sequence Easy-to-use Click&Go ogic for local output control Windows and WinCE VB/VC, and inux C APIs I/O control over Modbus/TCP and SNMP protocol Remote I/O > ioogik E4 The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Introduction Saves relay counter when the power is off The ioogik E4 is designed to record the how many times the built-in relay output is used. Even in the event of a sudden power failure, the E4 will still be able to record the last count to its internal storage, before the power is completely shut off. Specifications Digital Input Input: 6 fixed points Sensor Type: NPN, PNP, and dry contact I/O Mode: DI or Event Counter (up to 9 Hz) Dry Contact: ogic : short to GND ogic : open Wet Contact: ogic : to VDC ogic : to VDC Common Type: 6 points / COM Isolation: K VDC or K Vrms Counter Frequency: 9 Hz Digital Filtering Time Interval: ms Pin Assignment Over-voltage Protection: 6 VDC Relay Counter Saving: Yes Digital Output 6-Channel A, FormA (N.O.) Relay Output Relay Specification: Contact Rating: VDC, 4 VAC, VAC Inductance oad: A Resistance oad: A Breakdown Voltage: VAC Relay On/Off Time: ms, ms (Max.) Initial Insulation Resistance: G VDC Expected ife:, times (Typical) Initial Contact Resistance: m Ohm (Max.) Pulse Output: operations per minute at rated load Isolation: K VDC or K Vrms I/O (left to right) DI COM DI DI DI GND N.C. DI COM DI DI 4 DI GND N.C. R NO R C R NO R C R NO R C R NO R C R4 NO R4 C R NO R C DI Group DI Group Relays to Ordering Information ioogik E4: Active Ethernet I/O with 6 digital inputs and 6 relays DP6: CD module with 6 x text display and buttons info@moxa.com

11 Industrial Networking Solutions ioogik E4 Active Ethernet I/O with 8 analog inputs and analog outputs Easy-to-use Click&Go ogic for local output control 8-channel analog input voltage, current signal -channel analog output for voltage, current actuator control PC-based configuration utility and web console Windows and WinCE VB/VC, and inux C APIs I/O control over Modbus/TCP and SNMP protocol NIST-traceable calibration The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Introduction Combination of Analog Input and Output The ioogik E4 provides a combination of analog input and output in one module. The sensors and actuators it supports include ph, conductivity, pressure, flow, and valves. Remote I/O > ioogik E4 Specifications Analog Input Inputs: 8 Resolution: 6-bit Input Range: ± mv, ± mv, ± V, ± V, to ma, 4 to ma Data Format: 6-bit integer ( s complement) Accuracy: ±.% C, ±.% - and 6 C Sampling Rate (all channels): samples/sec (voltage) 6 samples/sec (current) Input Impedance: 9K ohms Built-in Resistor for Current Input: 6 ohm /6 Hz: 9 db min. Zero Drift: ±9 µv/ C Span Drift: ± ppm/ C Isolation: K VDC or K Vrms Analog Output Outputs: Resolution: -bit Output Range: to V, 4 to ma Drive Voltage: VDC for current output Data Format: bits Accuracy: ±.% C, ±.% - and 6 C Zero Drift: ±9 µv/ C Span Drift: ± ppm/ C oad Resistor: < ohms Pin Assignment I/O (left to right) Vin Vin Vin Vin Vin4 Vin Vin6 Vin7 Vout Iout Vout Iout Vin- Vin- Vin- Vin- Vin4- Vin- Vin6- Vin7- Vout- Iout- Vout- Iout- Ordering Information ioogik E4: Active Ethernet I/O with 8 analog inputs and analog outputs DP6: CD module with 6 x text display and buttons info@moxa.com

12 AVAIABE IN Q Remote Monitoring Solutions ioogik E4 Active Ethernet I/O with 4 analog inputs and configurable DIO 4 fixed differential analog input channels configurable digital input/output channels Instant event messaging by TCP, UDP, , SNMP Trap Adjustable sampling rate PC-based configuration utility and web console Easy-to-use Click&Go ogic for local output control I/O control over Modbus/TCP and SNMP protocol NIST traceable calibration Remote I/O > ioogik E4 The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Introduction Better I/O matrix for AI Monitoring The ioogik E4 is designed for AI monitoring and alarms, such as is used for water tank monitoring. The I/O combination provided by the ioogik E4 allows one AI channel to trigger up to digital outputs for ow, High and High, High alarm points. Front End Signal Conditioner The ioogik E4 works with PCs by using its digital output to reduce the loading from the PC s AI. The ioogik E4 also acts as a backup for the main control system. Specifications Analog Input Channels Channels: 4, differential input Resolution: 6-bit I/O Mode: 4 to ma, to V Sampling Rate (all channels): samples/sec for voltage 6 samples/sec for current Accuracy: ±.% C, ±.% - and 6 C Impedance: 9K ohms (min.) Built-in Resistor for Current Input: 6 ohms Configurable Digital Input/Output Channels Channels: points Ordering Information Digital Input Sensor: NPN, PNP sensor type I/O Mode: DI or event counter (up to 9 Hz) Dry Contact: ogic : short to GND ogic : Open Wet Contact: ogic : to VDC ogic : to VDC Common Type: 6 points per COM Power off Storage for Counter Mode: Yes Digital Output Sensor : Sink, 4 VDC, ma Pulse Wave Width: ms / Hz ioogik E4: Active Ethernet I/O with 4 analog inputs and configurable DIOs DP6: CD module with 6 x text display and buttons info@moxa.com

13 Industrial Networking Solutions ioogik E6 Active Ethernet I/O with 6 RTD inputs and 4 digital outputs Supports PT, JPT, Ni RTD sensor types, and resistance Adjustable RTD sampling rate Instant event messaging by TCP, UDP, , SNMP trap PC-based configuration utility and web console Easy-to-use Click&Go ogic for local output control Windows and WinCE VB/VC, and inux C APIs I/O control over Modbus/TCP and SNMP protocol NIST traceable calibration The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Introduction Brings Intelligence to Temperature Measurement The ioogik temperature I/O brings Intelligence to temperature sensors. It is equipped with virtual channels that are available for calculating the average value of each channel and the difference between two physical channels PC or controller NOT required. Great Compatibility with Popular RTD Temperature Sensors The ioogik E6 can be used with PT, PT, JPT, and Ni sensor types, and resistors up to.k ohms. You can use your own resistance sensor, such as PTC or NTC for your HVAC applications. Remote I/O > ioogik E6 Specifications RTD Channels: 6, RTD channels Input Type: Pt, JPt, Ni, RTD sensor, resistor Sampling Rate: samples/sec (all channels) Resolution:. C or. ohm Accuracy: ±.% C, ±.% - and 6 C Input Impedance: 6K ohms (min.) Digital Output Channels: 4, Sink, 4 VDC, ma Optical Isolation: K VDC or K Vrms Pulse out Frequency: Hz Over-voltage Protection: 4 VDC Over-current imit: 7 ma Over-temperature Shutdown: 7 C Pin Assignment I/O (left to right) EX IN EX IN EX IN EX IN EX4 IN4 EX IN IN- IN- IN- IN- IN4- IN- DO GND DO DO DO DO DO PWR Ordering Information ioogik E6: Active Ethernet I/O with 6 RTD inputs and 4 digital outputs DP6: CD module with 6 x text display and buttons info@moxa.com

14 Remote Monitoring Solutions ioogik E6 Active Ethernet I/O with 8 thermocouple inputs and 4 digital outputs Supports J, K, T, E, R, S, B, and N type thermocouple and mv modes Adjustable sampling rate Instant event messaging by TCP, UDP, , SNMP Trap PC-based configuration utility and web console Easy-to-use Click&Go ogic for local output control Windows and WinCE VB/VC, and inux C APIs I/O control over Modbus/TCP and SNMP protocol NIST traceable calibration Remote I/O > ioogik E6 The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Introduction Extending the Wiring ength The ioogik E6 extends the length of your sensors wiring by a factor of. For example, the usual length of a K-Type sensor m, but the ioogik E6 can accept meters of K-Type TC wiring. Brings Intelligence to Temperature Measurement The ioogik temperature I/O brings intelligence to temperature sensors. It is equipped with virtual channels that are available for calculating the average value of each channel and the difference between two physical channels PC or controller NOT required. Specifications Thermocouple Channels: 8, thermocouple input Sensor Type: J, K, T, E, R, S, B, N type TC and mv mode Sampling Rate (all channels): samples/sec Effective Resolution: 6-bit Accuracy: ±.% C, ±.% - and 6 C Input Impedance: M ohms or better Digital Output Channels: 4, Sink, 4 VDC/ ma Isolation: K VDC or K Vrms Pulse-out Frequency: Hz Over-voltage Protection: 4 VDC Over-current imit: 7 ma Over-temperature Shutdown: 7 C Ordering Information ioogik E6: Active Ethernet I/O with 8 thermocouple inputs and 4 digital outputs DP6: CD module with 6 x text display and buttons info@moxa.com

15 Industrial Networking Solutions ioogik R Serial Remote I/O ink Input and Output Signals over RS-48 The ioogik R series was designed for system integrators to acquire and control remote digital and analog devices over RS-48. Types of digital on/off devices that can be controlled include proximity switches, mechanical switches, push buttons, optical sensors, EDs, and light switches. Types of analog devices that can be controlled include ph, conductivity, temperature, humidity, pressure, flow, actuator, and valves. The ioogik R series of servers can work with the standard Modbus protocol. SCADA software or the MXIO D library can be used to access the server. Full Range of DI/DO and AI/AO Models RS-48 is still the most common interface used by many industries, and Moxa now offers a high quality line of remote I/O servers that support RS-48. Multi-functional digital I/O with DI/Event Counter and DO/Pulse Output modes Multi-function analog I/O with ma/mv/voltage modes Over-current and over-voltage protection PC-grade I/O design that ensures accuracy and reliability during field operation Remote management of firmware upgrades over RS-48 networks Independent Configuration of Multi-Functional DI/DO and AI/AO Channels Each input signal can be independently configured, with DI/Event Counter modes available for digital inputs and voltage/current modes available for analog inputs. Each digital output can be independently configured for DO or Pulse Output mode. The analog input channels support various signals ranging from ± mv to ±V at 6-bit resolution. The analog output channels support to V and 4 to -bit resolution. Easy Management of Firmware over RS-48 Remote I/O > ioogik R Serial Remote I/O Traditionally, it was difficult for users to update firmware over RS-48. Moxa now provides an easy method for updating firmware over an RS-48 network that allows users to perform remote firmware updates, reducing maintenance time and cost. Snap-On CD Module Traditionally, a PC was required to configure a remote I/O server. Moxa offers the optional snap-on CD module as an easier way to configure and monitor ioogik E and R servers. The CD module is hot-pluggable, so it can be installed or removed without turning off the server. info@moxa.com

16 Remote Monitoring Solutions ioogik R RS-48 remote I/O with digital inputs and 8 digital outputs -point 4 VDC digital input with DI/event counter mode, software selectable filtering time, and software selectable pulse width ED indicators for all I/O channels Over-temperature protection (up to 7 C) Over-current protection (4 ma/channel) Easy-to-use, quick programming lib for VB, VC, BCB Upgrade firmware over RS-48 Remote I/O > ioogik R The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Specifications Digital Input Inputs:, source type I/O Mode: DI or event counter (up to Hz) Dry Contact: ogic : short to GND ogic : open Wet Contact: ogic : to VDC ogic : to VDC (DI COM to DI) Common Type: points per COM Isolation: K VDC or K Vrms Digital Output Outputs: 8, sink type I/O Mode: DO or pulse output (up to Hz) On-state Voltage: 4 VDC nominal Output Current Rating: Max. ma per channel Optical Isolation: K VDC or K Vrms Protection: Over-temperature shutdown: Min. 7 C Over-current limit: typ. 4 ma/channel Output Frequency: Hz Pin Assignment I/O (left to right) DI COM DI DI DI DI DI4 DI DI6 DI7 DI8 DI9 DI DI DI. GND DO.PWR DO DO DO DO DO4 DO DO6 DO7 DO.GND Ordering Information ioogik R: RS-48 remote I/O server with digital inputs and 8 digital outputs DP6: CD module with 6 x text display and buttons info@moxa.com

17 Industrial Networking Solutions ioogik R4 RS-48 remote I/O with 8 analog inputs and analog outputs 8-channel analog input for millivolts (mv), voltage, current signal with wire-off detection (at 4 to ma) -channel analog output for voltage, current actuator control 6-bit resolution analog input, -bit resolution analog output Easy-to-use, quick programming lib for VB, VC, BCB NIST-Traceability calibration for analog I/O channels Upgrade firmware over RS-48 The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Specifications Analog Input Inputs: 8 Resolution: 6-bit Input Range: ± mv, ± mv, ± V, ± V, to ma, 4 to ma Data Format: 6-bit integer Accuracy: ±.% C, ±.% - and 6 C Sampling Rate (all channels): samples/sec (voltage) 6 samples/sec (current) Built-in Resistor for Current Input: 6 ohms Optical Isolation: K VDC or K Vrms Analog Output Outputs: Resolution: -bit Output Range: to V, 4 to ma Drive Voltage: VDC for current output Accuracy: ±.% C, ±.% -, 6 C /6 Hz: 9 db min. Zero Drift: ±9 µv/ C Span Drift: ± ppm/ C oad Resistor: < ohms Remote I/O > ioogik R4 Pin Assignment I/O (left to right) Vin Vin Vin Vin Vin4 Vin Vin6 Vin7 Vout Iout Vout Iout Vin- Vin- Vin- Vin- Vin4- Vin- Vin6- Vin7- Vout- Iout- Vout- Iout- Ordering Information ioogik R4: RS-48 remote I/O with 8 analog inputs and analog outputs DP6: CD module with 6 x text display and buttons info@moxa.com

18 Remote Monitoring Solutions iomirror E Peer-to-Peer I/O Direct Input-to-output Communication over an IP Network Remote I/O > iomirror E Peer-to-Peer I/O The iomirror E Ethernet I/O server is designed as a cable replacement solution that sends input signals to remote outputs over an Ethernet or IP network. iomirror can be used to connect remote sensor signals to PC controllers, DCS systems, or display devices over a network, without installing additional signal wires. iomirror in Different Network Infrastructures Ethernet Network Fiber Ethernet Network Exiting Etnernet Without Controller Output Module Input Module Redundant Ring Output Module Input Module Up to 8 Inputs Up to 8 Outputs Wireless AN Network Input Module Output Module info@moxa.com

19 Industrial Networking Solutions The Easiest Way to Connect Input Signals to Remote Outputs over an IP Network Configuring iomirror is easy with iomirroradmin for Windows. With iomirroradmin, input-to-output signal mapping between iomirror servers can be configured from a local or remote host. Basic Configuration, which is also available in the web console, is used for simple mapping of all channels from box to box. Advanced Configuration is used for customized channel-to-channel mapping and allows one input channel to be mapped to multiple output channels. iomirroradmin also provides a graphical representation of iomirror server relationships, complete with signal direction, making it easy to map signals quickly and accurately. Take Advantage of Existing Ethernet Infrastructure Why spend extra effort installing additional signal wires if you already have a high-speed Ethernet infrastructure? Modern ANs, including Ethernet, optical fiber, and wireless, already provide the necessary high-speed connectivity. General input/output signals can be carried by a pair of iomirror I/O servers, making wiring simpler than ever. Simultaneously Send Input Signals to Two ocations The iomirror E can send one input signal simultaneously to two digital outputs over the network. This function could be used, for example, to monitor tank levels from two different display panels. Easy and Flexible Installation Installing iomirror E servers is easy using the Windows utility that comes with each server. If all channels are mapped from one module to another, all you need to do is assign the remote IP address. For more sophisticated mapping, individual channels can be mapped quickly and easily using the comprehensive graphical user interface. Useful Troubleshooting Tools Many useful tools are provided that help keep you informed about the health and performance of your iomirror E servers and connections. Optional CD attachment for local IP configuration Alarm port for 4 VDC alarm devices, such as pole displays, EDs, and buzzers Inputs Ethernet Output Output Remote alarm and independent event log that records each connection and disconnection Fast recovery after network disconnection Modbus/TCP support for SCADA connectivity Remote I/O > iomirror E Peer-to-Peer I/O Using iomirror as Part of a Tank Monitoring Panel This real-world application uses iomirror in the vegetable oil industry, where oil tank levels are monitored constantly. The customer uses a computerbased SCADA system for general management and control, with an ED panel in the control room for direct monitoring of tank levels. The original solution was a significant challenge, since it meant maintaining meters of dedicated copper wire for 4 V signals. The advantage of using the iomirror Ethernet I/O server was that the existing fiber network could be used instead. The level sensor simply connects to an iomirror server, which is connected to the network. Sensor signals are automatically forwarded over the network to another iomirror server, which sends matching 4 VDC digital output signals directly to the ED. The iomirror system was so easy to set up that the customer completed the project in just a few days, and at very little cost. DI DO m DO DI Water Tank Control Panel info@moxa.com

20 Remote Monitoring Solutions Remote I/O > iomirror E Peer-to-Peer I/O Common Specifications for iomirror E series AN Ethernet: / Mbps, RJ4 Protection:. KV magnetic isolation Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP (MIB for I/O and Network), HTTP, SNTP Power Requirements Input Voltage: 4 VDC nominal, to 48 VDC DO Power: 4 VDC nominal, up to 4 VDC Physical Characteristics Wiring: I/O cable max. 4 AWG Environmental imits Operating Temperature: - to 6 C (4 to 4 F), to 9% RH Storage Temperature: -4 to 8 C (-4 to 8 F), to 9% RH Regulatory Approvals EMC: FCC part, CISPR (EN) Class B Dimensions (unit = mm) CE: IEC 6-4 IEC 6-6 Safety: U 8 Shock: IEC Freefall: IEC Vibration: IEC Warranty: years (see for details) Side View Front View Rear View info@moxa.com

21 Industrial Networking Solutions iomirror E Ethernet peer-to-peer I/O with 8 digital inputs and 8 digital outputs Direct input-to-output signal communication over IP High speed peer-to-peer I/O within ms One physical alarm port for connectivity status Quick and easy utility and web-based settings ocal alarm and remote alarm message Supports Modbus/TCP for remote monitoring Optional CD module for simple setup The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Introduction Direct input-to-output communication over IP The iomirror E Ethernet I/O server is designed as a cablereplacement solution that connects remote digital input signals to output signals over an IP network. The iomirror E provides 8 digital input channels, 8 digital output channels, and a /M Ethernet interface. Up to 8 pairs of digital input and output signals can be exchanged over Ethernet with another iomirror E as well as to a local PC or DCS controller. Over a local area network, the iomirror achieves low signal latency, which is typically ms. With iomirror, remote sensors can now be connected to local controllers or display panels over copper, fiber, or wireless Ethernet infrastructures. Signals can be transmitted over virtually unlimited distances, without noise problems. Specifications Digital Input Inputs: 8, source type I/O Mode: Digital Input Dry Contact: ogic : close to GND ogic : open Wet Contact: ogic : to VDC ogic : to VDC Isolation: K Vrms Common Type: 8 points per COM Split sensor signals to sixteen different locations The iomirror E can split one input signal to two digital output channels at two different IP addresses. Eight tank level signals can be monitored at sixteen different display panels, all at the same time. ocal alarm with remote alarm messages for monitoring connectivity The iomirror E has a 4 VDC alarm output channel that can activate an attached buzzer or display ED when the connection fails. In addition, both iomirror modules can send messages to the event log software. This ensures that at least one of the warning messages will reach the event log software. Digital Output Outputs: 8, sink type I/O Mode: Digital output On-status Voltage: 4 VDC (typical) Output Current Rating: Max. ma per channel Optical Isolation: K Vrms per K VDC Protection: Over-voltage Protection: VDC Over-current imit: 6 ma (typical) Over-temperature Shutdown: 6 C (min.) Alarm Port Output Outputs:, sink type On-status Voltage: 4 VDC (typical) Output Current Rating: Max. ma per channel Optical Isolation: K Vrms per K VDC Remote I/O > iomirror E info@moxa.com

22 Remote Monitoring Solutions I/O Pin Assignment I/O (left to right) DI COM DI DI DI DI DI 4 DI DI 6 DI 7 DI GND Alarm DO Power DO DO DO DO DO 4 DO DO 6 DO 7 DO GND Wiring Example Digital Input (Dry Contact) Digital Output Remote I/O > iomirror E Digital Input (Wet Contact with NPN Sensor) Pin DI_COM DI COM DI DI DI DI DI DI DI DI 4 DI DI DI 4 DI 6 DI DI 7 GND DO Power Alarm Port DO DO DO DO GND DO 4 DO AARM DO 6 DO 7 DO GND - NPN Sensors Brown Black Blue to 4 V NPN output V - ~4 V - Ordering Information iomirror E: Ethernet peer-to-peer I/O with 8 digital inputs and 8 digital outputs DP6: CD module with 6 x text display and buttons info@moxa.com

23 Industrial Networking Solutions DP6 CD Module Snap-on module for ioogik series Hot-pluggable display module for ioogik Active Ethernet I/O and serial remote I/O Easy, portable configuration kit for IP display and configuration Direct display for analog value and digital input, counter status No battery required (powered by I/O ) Supports ioogik E, ioogik R, and iomirror E series The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Installing the CD Module. Remove the ioogik server s top cover.. Plug in the CD module. Remote I/O > DP6 CD Module. Check and configure the IP address. 4. Check the IP and I/O status. Specifications CD Screen: 6 x text display (in English) Operating Temperature: to C ( to F) Storage Temperature: - to 7 C (-4 to 8 F) Ambient Relative Humidity: to 9% (non-condensing) Ordering Information DP6: CD module with 6 x text display and buttons info@moxa.com

24 Remote Monitoring Solutions Slice Form Factor, High Density Remote I/O Create a Compact, Flexible I/O Solution SCADA Custom Software MXIO ibrary Remote I/O > Slice Form Factor, High Density Remote I/O iomirror NA-4 RS-48 Adaptor EDS-78 Embedded Computer Turbo Ring < ms NA-4 Ethernet Adaptor E E DI/DO E4 AI/AO W E4 MIX I/O WiFi E6 E6 RTD/TC iomirror E4 Relay Output NA-4 RS- Adaptor M-4/8/6 Series Digital Input Modules M-4/8/6 Series Digital Output Modules Discrete I/O Analog I/O Actuator Relay Alarm On/Off device High/ow Open/Close Pressure Humidty sensor Flow sensor Drive/Valve High/ow Open/Close M-4 Series Analog Input Modules M-4 Series Analog Output Module Temperature sensor Fiber Optic Cable (BaseFX or BaseSX/X/HX/ZX) Twisted Pair Cable (/BaseT(X)) RS-/48 Cable info@moxa.com

25 Industrial Networking Solutions ioogik 4 Modular Remote I/O Flexible remote I/O with a variety of I/O modules ioogik remote I/O products from Moxa are used to connect a variety of sensors and actuators to computers and applications over standard Ethernet networks and the Internet. Sensors could be used for taking temperature, humidity, and light intensity readings, and actuators could include devices that apply pressure actuators and motor drives. Moxa also offers a line of RS-48 remote I/O servers that can be used with existing applications. By using one of Moxa s NPort wireless device servers, you can even connect to sensors and devices over a wireless AN network. Easy Maintenance Remote I/O > ioogik 4 Modular Remote I/O ioogik 4 servers provide spring type, removable terminal blocks (RTB) that allow you to preserve field wiring before replacing I/O expansion modules. Each I/O expansion module can be replaced quickly and easily. Slice Type I/O Modules Removable Terminal Block Spring Type Terminal Block Module Coding Tag info@moxa.com

26 Remote Monitoring Solutions Easy-to-Use Windows Utility ioadmin allows you to configure and monitor ioogik 4 modular I/O servers remotely. ioadmin automatically detects the installed ioogik Ethernet I/O server and presents the installation sequence of the I/O modules. ioadmin also detects and generates a Modbus address table, which can be printed or stored on a computer for SCADA software configuration. What You See Is What You Install!! The utility also allows you to:. Automatically search for installations. ook for help using online documentation. Generate reports of I/O combinations Remote I/O > ioogik 4 Modular Remote I/O Remote Configuration Self-diagnostic Function for Digital Output Channels ioadmin is a powerful, Windows-based configuration and management tool. You can use ioadmin to modify the IP address, update communication parameters, and configure all other settings easily. In addition, ioadmin can be used to configure ioogik modular I/O servers from a remote host. This means that ioogik modular I/O servers can be configured from anywhere over the Ethernet, which can help reduce your operating expense. The M-4, M-4, M-44, and M-4 modules include a self-diagnostic function to guarantee that the digital output signal is monitored electronically. The hardware-monitored status is written to the logic system, and you can obtain the actual digital output status over the network when the software sends a command to the module. This is all done internally, and configuration is not required. Check Remote I/O with a Web Browser Although ioadmin is the main configuration interface for ioogik servers, you can also check the following information using the ioogik server s web console: info@moxa.com

27 Industrial Networking Solutions Versatile Software Support ioogik 4 servers support the standard Modbus protocol and are compatible with most SCADA software. In addition, Moxa provides an easy-to-use MXIO D library that helps programmers develop application software with Visual Basic or C language under Windows. SCADA Software Packages SCADA DAQ Software Modbus Specific Driver SCADA SoftPC OPC Client rd Party OPC Server Programming Tools Visual Basic C-Applications MXIO D Utility & Diagnostics ioadmin Windows Utility Host Computer RS-/48 Ethernet Modbus/RTU Modular Remote I/O Modbus/TCP Modular Remote I/O Supports Various SCADA Software Packages The ioogik 4 line was designed for the standard Modbus protocol and can be used with most SCADA systems. The following SCADA software is compatible with ioogik 4 servers: Modicon Driver, Wonderware Intouch, GE Fanuc ifix and CIMPICITY, Broadwin, kingview, and Citect. In addition, we successfully tested the OPC Server Kepware, which means that ioogik 4 servers can be accessed either from a SCADA system or through an OPC Server. Note: The installation guides for different SCADA software packages can be downloaded from Moxa s download center. Dimensions (unit = mm) I/O Network Adaptor I/O Module Dimensions (.6") 7 (.7") 4 (.6") 7 (.7") 7 (.7") Remote I/O > ioogik 4 Modular Remote I/O 99 (.9") 6 (.4") (.8") 8 (.") 6 (.6") 99 (.9") 99 (.9") 6 (.4") (.8") 8 (.") 6 (.6") 99 (.9") 6 (.4") (.8") 8 (.") 6 (.6") (.8") 99 (.9") (.8") 7 (.7") Side View Front View Side View Side View Front View Removable View info@moxa.com

28 Remote Monitoring Solutions Modular Remote I/O Selection Guide I/O Modules Digital Input Modules Model M-4 M-4 M-4 M-4 M-8 M-8 M-6 M-6 M-4 M-4 Specs Channels Sink/Source Sink Source Sink Source Sink Source Sink Source Connector RTB RTB RTB RTB RTB RTB -pin -pin RTB RTB Voltage 4 VDC 4 VDC 48 VDC 48 VDC 4 VDC 4 VDC 4 VDC 4 VDC VAC VAC Isolation Optical isolation Remote I/O > ioogik 4 Modular Remote I/O Specs Specs Digital Output Modules Model M-4 M-4 M-8 M-8 M-6 M-6 M-4 M-4 M-44 M-4 M- M-4 Channels Sink/Source Sink Source Sink Source Sink Source Sink Source Sink Source Relay Triac Connector RTB RTB RTB RTB -pin -pin RTB RTB RTB RTB RTB RTB Voltage 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC VAC/ 4 VDC to VDC Current.A.A.A.A.A.A.A.A.A.A.A.A Isolation Optical isolation Diagnostics Yes Yes Yes Yes Analog Input Modules Model M-4 M-4 M-4 M-4 M-44 M-4 M-4 M-4 M-4 M-4 M-6 M-6 Channels Current to ma 4 to ma Voltage to V - to V to ma 4 to ma to V to V - to V to V Connector RTB RTB RTB RTB RTB RTB RTB RTB RTB RTB RTB RTB Resolution -bit -bit -bit -bit -bit 4-bit 4-bit 4-bit 4-bit 4-bit Isolation Sensor Input Optical isolation RTD (Ohm) Thermocouple (µv) Specs Analog Output Modules Model M-4 M-4 M-4 M-4 M-4 Channels Current to ma 4 to ma Voltage to V - to V to V Resolution -bit -bit -bit -bit -bit Connector RTB RTB RTB RTB RTB Isolation K VDC galvanic isolation Power Modules Model M-7 M-7 M-78 M-784 M-78 M-786 Specs Channels Voltage 4 VDC DC:, 4, 48 VDC AC: / VAC - V 4 VDC 4 for VDC 4 for 4 VDC Purpose System power Field power Shield signal Field power Field power Field power info@moxa.com

29 Industrial Networking Solutions NA-4 Ethernet network adaptor module ioogik 4 Modbus TCP/IP NA-4 SYS INK ACTIVE Field I/O Power 4V V SG SG System Power ( VDC) System Power (4 VDC) Shielding Ground System Power ( VDC) Non-isolation Switching Power The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. 4 V V 4V 4V Remote I/O > NA-4 Specifications Network Ethernet: / Mbps, RJ4 Software Features Protocols: Modbus/TCP, HTTP, Bootp IP Settings: ARP, Bootp, static IP Utility: ioadmin Programming ibrary: MXIO D library for Windows supporting Visual Basic, Visual C, Borland C Builder Number of I/O Modules: Max. of I/O expansion modules Power Requirements Power Input: to 8.8 VDC, 4 VDC typical Power Consumption: 6 ma 4 VDC Current for I/O Modules: VDC Field Power Rated Voltage: to 8.8 VDC, 4 VDC typical Current in Field Power Contact: Max. A Isolation System Power to I/O Driver: Optical isolation Environmental imits Operating Temperature: - to 6 C, to 9%RH Storage Temperature: -4 to 8 C Vibration: IEC-68--6, G in operation Regulatory Approvals EMC: CE EN-8, EN-8 Safety: U 8 Weight Net Weight: g Ordering Information Step : Select a Network Adaptor Module Step : Select I/O Modules Step : Select Power Modules (optional) NA-4 Series M-///4/6 Series M-7 Series NA-4: Ethernet Network Adaptor (Modbus/TCP) *The NA-4 Ethernet Network Adaptor is expandable with up to I/O modules. Please refer to pages - to -44 to select the M-series modules that you need for your own application. info@moxa.com

30 Remote Monitoring Solutions NA-4/4 RS-48 or RS- network adaptor modules Remote I/O > NA-4/4 The certification logos shown here apply to some or all of the products in this section. Please see the Specifications section or Moxa s website for details. Specifications Serial Communication Baudrate: to bps Data Bits: 7, 8 Parity Bits: None, Even, Odd Stop Bits:, Signals: NA-4: Data, Data-, Gnd, DIR NA-4: TxD, RxD, Gnd Software Features Protocols: Modbus/RTU, Modbus/ASCII Modbus Address: to 99 by rotary switches Utility: ioadmin Programming ibrary: MXIO D library for Windows supporting Visual Basic, Visual C, Borland C Builder Number of I/O Modules: Max. of I/O expansion modules Ordering Information ioogik 4 Modbus RS-48 NA-4 SYS TxD RxD I/O Field Power 4V V SG SG 4 V V 4V 4V System Power ( VDC) System Power (4 VDC) Shielding Ground Power Requirements Power Input: to 8.8 VDC, 4 VDC typical Power Consumption: 7 ma 4 VDC Current for I/O Modules: VDC Field Power Rated Voltage: to 8.8 VDC, 4 VDC typical Current in Field Power Contact: Max. A Isolation System Power to I/O Driver: Optical isolation System Power ( VDC) Non-isolation Switching Power Environmental imits Operating Temperature: - to 6 C, to 9%RH Storage Temperature: -4 to 8 C Vibration: IEC-68--6, G in operation Regulatory Approvals EMC: CE EN-8, EN-8 Safety: U 8 Weight Net Weight: g Step : Select a Network Adaptor Module Step : Select I/O Modules Step : Select Power Modules (optional) NA-4 Series M-///4/6 Series M-7 Series NA-4: RS-48 Network Adaptor (Modbus) NA-4: RS- Network Adaptor (Modbus) *The NA-4/4 RS-48/RS- Adaptors are expandable with up to I/O modules. Please refer to pages - to -4 to select the M-series modules that you need for your own application info@moxa.com

31 Industrial Networking Solutions Digital Input Modules 4 or 8-channel 4 VDC digital input modules M-4 CH CH CH CH 4 V V 4V 4V System Power ( VDC) M-4 4 digital inputs, sink, 4 VDC Inputs per Module: 4 points, sink type On-state Voltage: 4 VDC nominal, min. VDC to max. 8.8 VDC Min. Off-state Voltage: Max. VDC On-state Current: Max. 6 ma / 8.8 VDC Input Impedance: Typ..K ohms Filtering Time: Typ.. ms Common Type: 4 points/ COM Power Consumption: Max. VDC M-4 CH CH CH CH 4 V V 4V 4V System Power ( VDC) M-4 4 digital inputs, source, 4 VDC Inputs per Module: 4 points, source type On-state Voltage: 4 VDC nominal, min. VDC to max. 8.8 VDC Min. Off-state Voltage: Max. VDC On-state Current: Max. 6 ma / 8.8 VDC Input Impedance: Typ..K ohms Filtering Time: Typ.. ms Common Type: 4 points/ COM Power Consumption: Max. VDC Remote I/O > Digital Input Modules M CH CH CH CH 4 CH4 CH CH6 CH7 System Power ( VDC) M-8 8 digital inputs, sink, 4 VDC Inputs per Module: 8 points, sink type On-state Voltage: 4 VDC nominal, min. VDC to max. 8.8 VDC Min. Off-state Voltage: Max. VDC On-state Current: Max. 6 ma / 8.8 VDC Input Impedance: Typ..K ohms Filtering Time: Typ.. ms Common Type: External common Power Consumption: Max. VDC M CH CH CH CH 4 CH4 CH CH6 CH7 System Power ( VDC) M-8 8 digital inputs, source, 4 VDC Inputs per Module: 8 points, source type On-state Voltage: 4 VDC nominal, min. VDC to max. 8.8 VDC Min. Off-state Voltage: Max. VDC On-state Current: Max. 6 ma / 8.8 VDC Input Impedance: Typ..K ohms Filtering Time: Typ. ms Common Type: External common Power Consumption: Max. VDC info@moxa.com

32 Remote Monitoring Solutions 6-channel 4 VDC digital input modules M Ch V V 4V 4V 8 9 System Power ( VDC) M-6 6 digital inputs, sink, 4 VDC Inputs per Module: 6 points, sink type On-state Voltage: 4 VDC nominal, min. VDC to max. 8.8 VDC Min. Off-state Voltage: Max. VDC On-state Current: Max. 6 ma / 8.8 VDC Input Impedance: Typ..K ohms Filtering Time: Typ.. ms Common Type: 6 points/ COM Power Consumption: Max. 4 VDC Remote I/O > Digital Input Modules M Ch V V 4V 4V 8 9 System Power ( VDC) M-6 6 digital inputs, source, 4 VDC Inputs per Module: 6 points, source type On-state Voltage: 4 VDC nominal, min. VDC to max. 8.8 VDC Min. Off-state Voltage: Max. VDC On-state Current: Max. 6 ma / 8.8 VDC Input Impedance: Typ..K ohms Filtering Time: Typ.. ms Common Type: 6 points/ COM Power Consumption: Max. 4 VDC 4-channel 48 VDC digital input modules M-4 CH CH CH CH 4 V V 48V 48V System Power ( VDC) Field Power (48 VDC) * Field Power distributor required. M-4 4 digital inputs, sink, 48 VDC Inputs per Module: 4 points, sink type On-state Voltage: 48 VDC nominal, min. 4 VDC to max. 6 VDC Min. Off-state Voltage: Max. VDC On-state Current: Max. 4 ma / 48 VDC Input Impedance: Typ. K ohms Common Type: 4 points/ COM Power Consumption: Max. VDC M-4 CH CH CH CH 4 V V 48V 48V System Power ( VDC) Field Power (48 VDC) M-4 4 digital inputs, source, 48 VDC Inputs per Module: 4 points, source type On-state Voltage: 48 VDC nominal, min. 4 VDC to max. 6 VDC Min. Off-state Voltage: Max. VDC On-state Current: Max. 4 ma / 48 VDC Input Impedance: Typ. K ohms Common Type: 4 points/ COM Power Consumption: Max. VDC * Field Power distributor required info@moxa.com

33 Industrial Networking Solutions 4-channel / VAC digital input modules M-4 CH CH CH CH 4 N N System Power ( VDC) Field Power ( VAC N) Field Power ( VAC ) * Field Power distributor required. M-4 CH CH CH CH 4 N N System Power ( VDC) Field Power ( VAC) Field Power ( VAC N) Field Power ( VAC ) * Field Power distributor required. Ordering Information M-4 4 digital inputs, VAC Inputs per Module: 4 points On-state Voltage: VAC nominal, min. 8 VAC to max. VAC Min. Off-state Voltage: Max. 4 VAC On-state Current: Max. 8 ma / VAC Input Impedance: Typ. K ohms Common Type: 4 points/ COM (single common) Power Consumption: Max. VDC M-4 4 digital inputs, VAC Inputs per Module: 4 points On-state Voltage: 4 VAC nominal, min. 7 VAC to max. 64 VAC Min. Off-state Voltage: Max. 4 VAC On-state Current: Max. ma / 64 VAC Input Impedance: Typ. K ohms Common Type: 4 points/ COM (single common) Power Consumption: Max. VDC Remote I/O > Digital Input Modules Specs Digital Input Modules Model M-4 M-4 M-4 M-4 M-8 M-8 M-6 M-6 M-4 M-4 Channels Sink/Source Sink Source Sink Source Sink Source Sink Source Connector RTB RTB RTB RTB RTB RTB -pin -pin RTB RTB Voltage 4 VDC 4 VDC 48 VDC 48 VDC 4 VDC 4 VDC 4 VDC 4 VDC VAC VAC Isolation Optical isolation info@moxa.com

34 Remote Monitoring Solutions Digital Output Modules 4 or 8-channel 4 VDC digital output modules Remote I/O > Digital Output Modules M-4 CH CH CH CH 4 4V 4V 4V 4V M-4 CH CH CH CH 4 V V V V System Power ( VDC) System Power ( VDC) M-4 4 digital outputs, sink, 4 VDC,.A Outputs per Module: 4 points, sink type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off eakage Current: Max. µa Output Current Rating: Max..A per channel Common Type: 4 points /4 COM (single common) Power consumption: Max. 4 VDC M-4 4 digital outputs, source, 4 VDC,.A Outputs per Module: 4 points, source type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off eakage Current: Max. µa Output Current Rating: Max..A per channel Common Type: 4 points/4 COM (single common) Power Consumption: Max. 4 VDC M CH CH CH CH 4 CH4 CH CH6 CH7 System Power ( VDC) M-8 8 digital outputs, sink, 4 VDC,.A Outputs per Module: 8 points, sink type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off eakage Current: Max. µa Output Current Rating: Max..A per channel Common Type: 8 points/external common (single common) Power Consumption: Max. 6 VDC M CH CH CH CH 4 CH4 CH CH6 CH7 System Power ( VDC) M-8 8 digital outputs, source, 4 VDC,.A Outputs per Module: 8 points, source type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off eakage Current: Max. µa Output Current Rating: Max..A per channel Common Type: 8 points/external common (single common) Power Consumption: Max. 6 VDC info@moxa.com

35 Industrial Networking Solutions 4-channel digital output modules with diagnostics M-4 CH CH CH CH 4 4V 4V 4V 4V System Power ( VDC) M-4 4 digital outputs, diagnostics, sink, 4 VDC,.A Outputs per Module: 4 points, sink type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off eakage Current: Max. µa Output Current Rating: Max..A per channel Common Type: 4 points/4 COM (single common) Self Diagnostics: Yes Power Consumption: Max. 4 VDC M-4 CH CH CH CH 4 V V V V M-44 CH CH CH CH 4 4V 4V 4V 4V System Power ( VDC) System Power ( VDC) M-4 4 digital outputs, diagnostics, source, 4 VDC,.A Outputs per Module: 4 points, source type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off eakage Current: Max. µa Output Current Rating: Max..A per channel Common Type: 4 points /4 COM (single common) Self Diagnostics: Yes Power Consumption: Max. 4 VDC M-44 4 digital outputs, diagnostics, sink, 4 VDC, A Outputs per Module: 4 points, sink type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off leakage Current: Max. µa Output Current Rating: Max. A per channel Common Type: 4 points/4 COM (single common) Self Diagnostics: Yes Power Consumption: Max. 4 VDC Remote I/O > Digital Output Modules M-4 CH CH CH CH 4 V V V V System Power ( VDC) M-4 4 digital outputs, diagnostics, source, 4 VDC, A Outputs per Module: 4 points, source type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off eakage Current: Max. µa Output Current Rating: Max. A per channel Common Type: 4 points/4 COM (single common) Self Diagnostics: Yes Power Consumption: Max. 4 VDC info@moxa.com

36 Remote Monitoring Solutions 6-channel digital output modules M Ch V V 4V 4V 8 9 System Power ( VDC) M-6 6 digital outputs, sink, 4 VDC,.A Outputs per Module: 6 points, sink type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off eakage Current: Max. µa Output Current Rating: Max..A per channel Max. 4A per common Common Type: 6 points / COM (single common) Power Consumption: Max. 8 VDC Remote I/O > Digital Output Modules M Ch V V 4V 4V 8 9 System Power ( VDC) M-6 6 digital outputs, source, 4 VDC,.A Outputs per Module: 6 points, source type Output Voltage Range: 4 VDC nominal, min. VDC to max. 8.8 VDC On-state Voltage Drop: Max.. C On-state Current: Min. ma per channel Off eakage Current: Max. µa Output Current Rating: Max..A per channel Max. 4A per common Common Type: 6 points / COM (single common) Power Consumption: Max. 8 VDC info@moxa.com

37 Industrial Networking Solutions -channel relay output module M-4 M- CH CH 4 N N CH CH Ch Ch 4 System Power ( VDC) COM (to N or VDC) Field Power (N or VDC) Field Power ( VAC or 4 VDC) * Field power distributor required when the field power is not 4 VDC. System Power ( VDC) NC NC NC: No Connection to VAC Field Power ( VAC N) Field Power ( VAC ) * Field Power distributor required when the field power is not 4 VDC. M- digital outputs, relay, 4 VDC/ VAC, A Outputs per Module: points, relay Relay Type: Form A, Normally Open (N.O.) Single Pole, Single Throw (SPST) Output Voltage Range: oad dependent to 8.8 VDC / A resistive 48 VDC /.8A resistive VAC /.A resistive VAC / A resistive Min. oad: µa, m VDC per point Max. On-state Voltage A, resistive load, 4 VDC Off-state eakage Current: Max.. ma Common Type: point/ COM Power Consumption: Max. 6 VDC M-4 digital outputs, Triac, to VAC,.A Outputs per Module: points Switch Type: Zero crossing Rated oad Voltage: to VAC Output Current Rating:. to.a Frequency Range: 47 to 6 Hz Surge Current: 4A (6 ms) /4A (S) On-state Voltage Drop:. Vrms (max. load) Off-state eakage Current: Max.. ma Common Type: points / COM Power Consumption: Max. VDC Remote I/O > Digital Output Modules Ordering Information Specs Digital Output Modules Model M-4 M-4 M-8 M-8 M-6 M-6 M-4 M-4 M-44 M-4 M- M-4 Channels Sink/Source Sink Source Sink Source Sink Source Sink Source Sink Source Relay Triac Connector RTB RTB RTB RTB -pin -pin RTB RTB RTB RTB RTB RTB Voltage 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC 4 VDC VAC/ 4 VDC Current.A.A.A.A.A.A.A.A.A.A.A.A Isolation Optical isolation Diagnostics Yes Yes Yes Yes to VDC info@moxa.com

38 Remote Monitoring Solutions Analog Input Modules 4-channel analog input modules, -bit resolution Remote I/O > Analog Input Modules M-4xx M-4xx CH CH CH CH 4 G G CG CG CH CH CH CH 4 G G CG CG System Power ( VDC) Current to ma (M-4/4) Current 4 to ma (M-4/4) Shielding Ground 4-channel analog input modules, -bit resolution Power ( VDC) 4-channel analog input modules, -bit resolution Power (GND) Voltage to V (M-4/4) Voltage - to V (M-4/4) Voltage to V (M-44/4) Shielding Ground M-4 4 analog inputs, to ma, bits M-4 4 analog inputs, 4 to ma, bits Input Specifications Resolution in Ranges: bits, 4.88 µa/bit (M-4) bits,.9 µa/bit (M-4) Input Current Range: to ma (M-4) 4 to ma (M-4) Data Format: 6-bit integer ( s complement) Accuracy: ±.%, C ±.%, C, 6 C Input Impedance: ohms Conversion Time: 4 ms / all channels General Specifications Power Consumption: Max. VDC Isolation: I/O to logic: Photocoupler isolation Wiring: I/O cable max. AWG4 M-4 4 analog inputs, to V, bits M-4 4 analog inputs, - to V, bits M-44 4 analog inputs, to V, bits Input Specifications Resolution in Ranges: bits,.44 mv/bit (M-4) bits, 4.88 mv/bit (M-4) bits,. mv/bit (M-44) Input Current Range: to VDC (M-4) - to VDC (M-4) to VDC (M-44) Data Format: 6-bit integer ( s complement) Accuracy: ±.%, C ±.%, C, 6 C Input Impedance: K ohms Conversion Time: 4 ms / all channels General Specifications Power Consumption: Max. VDC Isolation: I/O to logic: Photocoupler isolation Wiring: I/O cable max. AWG info@moxa.com

39 Industrial Networking Solutions 4-channel analog input channels, 4-bit resolution M-4xx M-4xx CH CH CH CH 4 G G CG CG CH CH CH CH 4 G G CG CG System Power ( VDC) Current to ma (M-4/4) Current 4 to ma (M-4/4) Shielding Ground 4-channel analog input modules, -bit resolution Power ( VDC) 4-channel analog input modules, -bit resolution Power (GND) Voltage to V (M-4/4) Voltage - to V (M-4/4) Voltage to V (M-44/4) Shielding Ground M-4 4 analog inputs, to ma, 4 bits M-4 4 analog inputs, 4 to ma, 4 bits Input Specifications Resolution in Ranges: 4 bits,. µa/bit (M-4) 4 bits,.98 µa/bit (M-4) Input Current Range: to ma (M-4) 4- ma (M-4) Data Format: 6-bit integer ( s complement) Accuracy: ±.%, C ±.%, C, 6 C Input Impedance: ohms Conversion Time: 4 msec. / all channels General Specifications Power Consumption: Max. VDC Isolation: I/O to logic: Photocoupler isolation Wiring: I/O cable max. AWG4 M-4 4 analog inputs, to V, 4 bits M-4 4 analog inputs, - to V, 4 bits M-4 4 analog inputs, to V, 4 bits Input Specifications Resolution in Ranges: 4 bits,.6 mv/bit (M-4) 4 bits,. mv/bit (M-4) 4 bits,. mv/bit (M-4) Input Current Range: to VDC (M-4) - to VDC (M-4) to VDC (M-4) Data Format: 6-bit integer ( s complement) Accuracy: ±.%, C ±.%, C, 6 C Input Impedance: K ohms Conversion Time: 4 ms / all channels General Specifications Power Consumption: Max. VDC Isolation: I/O to logic: Photocoupler isolation Wiring: I/O cable max. AWG4 Remote I/O > Analog Input Modules info@moxa.com

40 Remote Monitoring Solutions Temperature Input Modules -channel temperature input modules, RTD or thermocouple input Remote I/O > Temperature Input Modules M-6 CH CH CH-A CH-B CH CH 4 G G CG CG M-6 CH CH CH CH CH CH- 4 G G CG CG System Power ( VDC) Shielding Ground RTD System Power ( VDC) Voltage to V Shielding Ground Thermocouple M-6 analog inputs, RTD: PT, JPT Input Specifications Sensor Types: PT, PT, PT, PT, PT, JPT, JPT, JPT, JPT, NI, NI, NI, NI, NI, CU, Resistance milli-ohm/bit, Resistance milli-ohm/bit, Resistance milli-ohm/bit Data Format: 6-bit integer ( s complement) Resolution:. C / milli-ohm Accuracy: ±.%, C ±.%, C, 6 C Input Impedance: K ohms Conversion Time: ms / all channels Diagnostics: Range over (if range over, data=dx8) General Specifications Power Consumption: Max. 8 VDC Isolation: I/O to logic: Photocoupler isolation Wiring: I/O cable max. AWG4 M-6 analog inputs, thermocouple Input Specifications Sensor Types: Type J/K/T/E/R/S/B/N//U/C/D mv input µv/bit, µv/bit Data Format: 6-bit integer ( s compliment) Resolution:. C / uv Accuracy: ±.%, C ±.%, C, 6 C Input Impedance: K ohms Conversion time: ms / all channels Diagnostics: Range over (if range over, data=dx8) General Specifications Power Consumption: Max. 8 VDC Isolation: I/O to logic: Photocoupler isolation Wiring: I/O cable max. AWG4 Ordering Information Specs Analog Input Modules Model M-4 M-4 M-4 M-4 M-44 M-4 M-4 M-4 M-4 M-4 M-6 M-6 Channels Current to ma 4 to ma to ma 4 to ma Voltage to V - to V to V to V - to V to V Connector RTB RTB RTB RTB RTB RTB RTB RTB RTB RTB RTB RTB Resolution -bit -bit -bit -bit -bit 4-bit 4-bit 4-bit 4-bit 4-bit Isolation Sensor Input Optical isolation RTD (Ohm) Thermocouple (µv) info@moxa.com

41 Industrial Networking Solutions Analog Output Modules -channel analog input modules, -bit resolution M-4x CH CH NC NC 4 G G CG CG M-4x CH CH NC NC 4 G G CG CG System Power ( VDC) Current to ma (M-4) Current 4 to ma (M-4) R< Ohm Shielding Ground System Power ( VDC) Voltage to V (M-4) Voltage - to V (M-4) Voltage to V (M-4) R > K Ohm Shielding Ground M-4 analog outputs, to ma, bits M-4 analog outputs, 4 to ma, bits Output Specifications Resolution in Ranges: bits, 4.88 µa/bit (M-4) bits,.9 µa/bit (M-4) Output Current Range: to ma (M-4) 4 to ma (M-4) Data Format: 6-bit integer ( s complement) Accuracy: ±.%, C ±.%, C, 6 C Output Impedance: Max. ohms Conversion Time: ms / all channels Power Consumption: Max. 6 VDC Isolation: I/O to logic: Photocoupler isolation Wiring: I/O cable max. AWG4 M-4 analog outputs, to V, bits M-4 analog outputs, - to V, bits M-4 analog outputs, to V, bits Input Specifications Resolution in Ranges: bits,.44 mv/bit (M-4) bits, 4.88 mv/bit (M-4) bits,. mv/bit (M-4) Output Current Range: to VDC (M-4) - to VDC (M-4) to VDC (M-4) Data Format: 6-bit integer ( s complement) Accuracy: ±.%, C ±.%, C, 6 C Output Impedance: Min. K ohms Conversion Time: ms / all channel Power Consumption: Max. VDC Isolation: I/O to logic: Photocoupler isolation Wiring: I/O cable max. AWG4 Remote I/O > Analog Output Modules Ordering Information Analog Output Modules Model M-4 M-4 M-4 M-4 M-4 Channels Current to ma 4 to ma Specs Voltage to V - to V to V Resolution -bit -bit -bit -bit -bit Connector RTB RTB RTB RTB RTB Isolation K VDC galvanic isolation info@moxa.com

42 Remote Monitoring Solutions Power Modules Power expansion and field power or potential distribution Power expansion module The system power expansion module is designed to provide extra power for connected I/O expansion modules. Each network adaptor can VDC. If you require more power for your installed I/O expansion modules, you will need to use an M-7 module. However, please note that the M-7 can only provide VDC. Remote I/O > Power Modules ma ma ma ma ma ma Total: 4 ma Field power distributor module ma ma ma Supports ma ma ma ma ma Total: ma ma... Supports ma Supports ma The field power distributor modules are designed to isolate different field voltages. For example, before you connect a 48 VDC or VAC DI/O module to a 4 VDC DI/O module, you will need an M-7 field power module. 4 VDC 48 VDC VAC V 4V V 48V V VAC Potential distributor module There are three types of potential distributor modules that provide by itself does not have a 4V wiring point. You may add an M-78 for extra wiring points, such as shielding ground, V field power, and 4V easier wiring. field power. For example, the 8-channel digital input (sink type) module M-8 M-784 M-8 M info@moxa.com

43 Industrial Networking Solutions M-7 System power module M-7 Field power module M-7 4V V CG CG 4 V V 4V 4V System Power ( VDC) Non-isolation Switching Power System Power Input ( VDC) System Power Input (4 VDC) Shield Ground Field Power Input ( VDC) Field Power Input (4 VDC) System Input Voltage: 4 VDC, to 8.8 VDC Field Power Input Voltage: 4 VDC (±%) Output Voltage: VDC (Max.) Field Power Contacts Current: A (Max.) M-7 CG CG 4 N N P P System Power ( VDC) *Field Power ranging from 4/48 VDC to / VAC Shield Ground Field Power Input (N) Field Power Input (P) Field Power (N) Field Power (P) *Field Power contact disconnected Field Power Input Voltage: DC: VDC, 4 VDC, 48 VDC AC: VAC, VAC Current for Field Power Contacts: A (Max.) M-78 Shield signal M-784 VDC M-78 4 VDC M-786 4/ VDC M-78 System Power ( VDC) M-784 System Power ( VDC) M-78 System Power ( VDC) M-786 System Power ( VDC) Remote I/O > Power Modules CG CG V V 4V 4V 4V V CG CG V V 4V 4V 4V V 4 CG CG 4 V V 4 4V 4V 4 4V V CG CG Field Power (N) Field Power (P) V V 4V 4V 4V V Channels: 8 Mode: Shield Signal Channels: 8 Mode: VDC Channels: 8 Mode: 4 VDC Channels: 4 Mode: 4 VDC or VDC Ordering Information Power Modules Model M-7 M-7 M-78 M-784 M-78 M-786 Specs Channels Voltage 4 VDC DC:, 4, 48 VDC AC: / VAC --- V 4 VDC 4 for VDC 4 for 4 VDC Purpose System power Field power Shield signal Field power Field power Field power info@moxa.com

44 Remote Monitoring Solutions Accessories TB 6 DIN-rail mounting screw terminal module with -pin connector pins, one-to-one assignment Connector pitch:.8 mm DIN-rail mounting type Dimensions (W x x H): 77. x 67. x mm RoHS compliant Remote I/O > Accessories -pin to -pin flat cable Connecting between TB6 and ioogik 4 series ength: cm Number of pins: M-8-PK Removable terminal block Terminal block for ioogik 4 series Packaging: 9 pcs in one box M-8-PK Marker with to 9 numbering M-84-PK Blank marker Marker for ioogik 4 series Packaging: pcs in one box Ordering Information TB 6: DIN-rail mounting screw terminal module with -pin connector -pin to -pin flat cable: P-to-P flat cable, mm M-8-PK: Removable terminal block, 9 pcs per pack M-8-PK: Marker with to 9 numbering, white color, pcs M-84-PK: Blank marker, pcs info@moxa.com