Operating instructions RFID evaluation unit DTE / / 2011

Transcription

1 Operating instructis RFID evaluati unit DTE100 UK / / 2011

2 Ctents 1 Preliminary note Notes this document Symbols used Safety instructis General Installati and cnecti Tampering with the device Functis and features "PROFIBUS IN" and "PROFIBUS OUT" fieldbus interface "COM" cfigurati interface RFID antennas Requirements the Profibus DP master Functi Installati Installati distance Installati orientati Mounting optis Mounting DIN rail Removal Mounting plate Electrical cnecti AUX voltage supply Field bus cnecti PROFIBUS IN Profibus address Fieldbus cnecti PROFIBUS OUT Factory setting of the Ethernet parameters Process cnectis IO-1... IO Use as input/output to IEC Use with RFID read/write heads Functial earth cnecti Mounting DIN rail Mounting plate Operating and display elements

3 7.1 Reset to factory settings LED indicators LED AUX LED PROFIBUS LED COM LEDs IO1... IO Special device- LED indicatis Diagnosis Technical data...20uk 9.1 Data sheets Device manual Maintenance, repair and disposal Approvals/standards Scale drawing...21 Licences and trademarks Microsoft und Internet Explorer are registered trademarks of Microsoft Corporati. All trademarks and company names are subject to the copyright of the respective companies. 3

4 1 Preliminary note 1.1 Notes this document This document applies to the RFID evaluati unit DTE100. It is part of the device and ctains informati about the correct handling of the product. This document is intended for qualified electricians. These specialists are people who are qualified by their training and their experience to see and to avoid possible hazards that may be caused during operati of the device. Read this document before use to familiarise yourself with operating cditis, installati and operati. Keep this document during the entire durati of use of the device. 1.2 Symbols used Instructis > Reacti, result [ ] Designati of pushbutts, butts or indicatis Cross-reference Important note N-compliance can result in malfuncti or interference. Informati Supplementary note 2 Safety instructis 2.1 General Observe these operating instructis. Adhere to the warning notes the product. N-observance of the instructis, operati which is not in accordance with use as prescribed below, wrg installati or incorrect handling can affect the safety of operators and machinery. 2.2 Installati and cnecti The device must ly be installed, cnected and put into operati by a qualified electrician as the safe functi of the device and machinery is ly guaranteed when installati is correctly carried out.the installati and cnecti must 4

5 comply with the applicable natial and internatial standards. Respsibility lies with the pers installing the device. This is a class A product. The device may cause radio interference in domestic areas. In this case it can be necessary for the user to take appropriate measures. 2.3 Tampering with the device Tampering with the device is not allowed and will lead to an exclusi of liability and warranty. Tampering with the device can affect the safety of operators and machinery. Do not open the device. Do not insert any objects into the device. Prevent metal foreign bodies from penetrating. UK 3 Functis and features The RFID evaluati unit DTE100 integrates a Profibus DP interface and 4 channels for the cnecti of field devices. Each channel can be used either for the cnecti of an RFID antenna or as input/output to IEC The device ctrols the data exchange to the RFID antennas or the sensor/actuator level. communicates with the higher-level ctrol level via Profibus. allows device cfigurati via a web server. Applicati examples: Material flow ctrol in producti lines Warehouse management by the automatic detecti of stored products Tank management, order picking or product tracking 3.1 "PROFIBUS IN" and "PROFIBUS OUT" fieldbus interface Profibus DP-V0 / DP-V1 interface isolated from potential Baud rate 9600 baud to 12 Mbaud Max. distance between gateway and host: depending the baud rate max. 127 participants, 32 per segment 5

6 3.2 "COM" cfigurati interface 10 Mbps and 100 Mbps TCP/IP - Transport Ctrol Protocol/ Internet Protocol UDP - User Datagram Protocol IT functiality: HTTP server M12, twisted pair 3.3 RFID antennas The device supports up to four RFID read/write heads of type ANT51x from ifm electric gmbh. You can find informati about the matching read/write heads our website at: data sheet search ANT Requirements the Profibus DP master Profibus DP master of class 1 (DPM1) with DPV0 support or Profibus DP master of class 1 (DPM1) with DPV1 support (recommended) By using the DPV1 services the data size within the cyclically transferred input/output data of the Profibus DP master is csiderably reduced. 4 Functi You can find detailed informati about the functi of the system in the device manual at: data sheet search DTE100 Operating instructis 6

7 5 Installati 5.1 Installati distance Due to the internal heating of the device a minimum distance to other objects of 10 mm is to be taken into account during installati. UK A = 10 mm 5.2 Installati orientati The installati orientati can be freely selected. In a wet envirment upside-down mounting is not permitted. 7

8 5.3 Mounting optis Mounting DIN rail The device can be installed a DIN rail of type NS35/15 or NS35/ Angle the device and place the fixing clamp to the upper edge of the DIN rail. 2. Press device down. 3. Simultaneously rotate the device in the directi of the DIN rail Removal 1. Press device down. 2. Simultaneously rotate the device away from the DIN rail. 3. Remove the device from the top. 8

9 5.3.3 Mounting plate The device can be fixed to a mounting plate using 2 screws (M4 x 35 or lger). M4 M4 UK This installati mode is recommended for vibrati and shock requirements. 9

10 6 Electrical cnecti The device must be cnected by a qualified electrician. Discnect power before cnecting the device. Observe the natial and internatial regulatis for the installati of electrical equipment. Ensure voltage supply to EN 50178, SELV, PELV. Cnect the device according to the indicated pin cnecti. A total current csumpti of the device of 3 A must not be exceeded. Please note the following points to ensure protecti rating IP 67: Cover the unused sockets with protective caps. Tighten all protective caps and cnectors with a tightening torque of 1 Nm. You will find matching accessories at Accessories Protective cap Torque wrench ifm article number E73004 E AUX voltage supply Cnect the device to the voltage supply using an M12 cnecti cable. Pin Cnecti V DC 2 not used 3 0 V 4 not used 5 not used You can find matching cnecti cables at: data sheet search DTE100 Accessories 10

11 6.2 Field bus cnecti PROFIBUS IN Cnect the device to a Profibus DP master e.g. S7-315 DP using a suitable M12 Profibus cnecti cable Note: screened cnecti cable required Pin Cnecti 1 not used 2 RxD/TxD-N (bus A) 3 not used 4 RxD/TxD-P (bus B) 5 not used UK The following cnecti cables are recommended for use with the device: Descripti Cnecti cable, straight - angled Cable plug, straight Socket, straight ifm article number E12316, E12317 E12318, E12319 E12320, E Profibus address Profibus address delivery: 126 The address can be adapted via the integrated web server ( chapter 6.4) or a suitable Profibus DP master of class 1 or Fieldbus cnecti PROFIBUS OUT Cnect the device to the next Profibus DP participant using a suitable M12 Profibus cnecti cable. As an alternative: Cnect terminating resistor if the device is operated at the end of the Profibus DP line. 11

12 1 2 Pin 1 P5V Cnecti RxD/TxD-N (bus A) 3 DGND Note: screened cnecti cable required 4 RxD/TxD-P (bus B) The following terminating resistor is suitable for use with the device: Descripti Terminating resistor ifm article number E12315 Ethernet cnecti COM The device features an Ethernet interface for parameter setting and diagnosis. The settings are made via a web browser, e.g. Microsoft Internet Explorer as from V7.0. Cnect the device to a PC using a suitable M12 Ethernet cnecti cable. 1 2 Pin Cnecti 1 TD RD+ 3 TD- Note: screened cnecti cable required 4 RD- The following cnecti cable is suitable for use with the device: Descripti Ethernet cnecti cable M12 / RJ45 ifm article number E Factory setting of the Ethernet parameters The following values are preset delivery of the device: 12

13 Parameters Factory setting IP address Gateway address Subnet mask Auto-negotiati 6.4 Process cnectis IO-1... IO-4 Each process cnecti can be used as input/output to IEC or for cnecti of an RFID read/write head. The cnectis are set via the hardware cfigurati of the Profibus DP master. UK Pin Cnecti L+ 2 switching input (I/Q) 3 L- 4 switching output (C/Qo) or input (C/Qi) 5 not used The evaluati unit has to be discnected before field units are cnected. Please note that the total current csumpti of the device must not exceed the value of 3 A Use as input/output to IEC Ensure the following settings in the Profibus master: Applicati Example Cfigurati in the Profibus DP master Input sensor input Output actuator output 13

14 6.4.2 Use with RFID read/write heads There are various operati modes when an RFID read/write head of type ANT51x is cnected: Operating mode Acyclic executi of commands via PIB Read UID from tag or write UID to tag Cyclic executi of commands Cfigurati in the Profibus DP master PIB state RWH UID RWH STRG You can find detailed informati about the available operating modes in the device manual at: data sheet search DTE100 Operating instructis 14

15 6.5 Functial earth cnecti. To ensure trouble-free operati the device must be cnected to an earth potential free from external voltage Mounting DIN rail The cnecti is made automatically via the DIN rail. Note that the DIN rail must be cnected with the earth potential. UK Mounting plate When the device is fixed a mounting plate, cnecti is made via the left fixing screw. Note that the plate must be cnected with the earth potential. 15

16 7 Operating and display elements 7.1 Reset to factory settings Profibus address and Ethernet parameters can be reset to the factory settings. Take the following steps: Remove all cable cnectis from the device. Insert an electrically cductive bridge between pin 1 and pin 3 the process cnecti IO-3. Cnect device with the voltage supply and wait until the yellow LED indicati AUX and IO-3 flashes at approx. 8 Hz. Discnect the device from the voltage supply and cnect it again. > > The settings are reset. 7.2 LED indicators The device indicates the current status of the interface via the status LEDs LED AUX LED green LED yellow Status Note off off no voltage supply U AUX < 5 V flashes at 2 Hz voltage supply too low 5 V U AUX 18 V off voltage supply OK 18 V U AUX 36 V flashes at 8 Hz voltage supply too high U AUX > 36 V 16

17 7.2.2 LED PROFIBUS LED red LED green Status Note off off flashes at 2 Hz no cnecti to the Profibus DP master cnecti to Profibus DP master exists, no cyclical data exchange cnecti to the Profibus DP master exists, cyclical data exchange running Profibus DP protocol stack in the device does not run or no cnecti to the DP master device is in the "WAIT_PRM" or "WAIT_CFG" state device is in the "DATA_EXCH" state" UK LED COM LED green LED yellow Status Note off off off flashes sporadically no cnecti to another Ethernet counterpart cnecti to Ethernet counterpart exits, no data exchange cnecti to Ethernet counterpart exists, data exchange running link status "no link" link status "link", "no traffic" link status "link", "traffic" 17

18 7.2.4 LEDs IO1... IO4 The LED indicatis of the process cnectis differ with each cnecti cfigurati. Use as input to IEC LED green LED yellow Status Note off off interface deactivated interface in DP master not cfigured off interface activated, input L level (0 V) - interface activated, input H level (24 V) - flashes at 8 Hz flashes at 8 Hz overload or short circuit - Use as output to IEC LED green LED yellow Status Note off off interface deactivated interface in DP master not cfigured off interface activated, output L-active (0 V) - interface activated, output H-active (24 V) - flashes at 8 Hz flashes at 8 Hz overload or short circuit - 18

19 Use with RFID read/write heads LED green LED yellow Status Note off off interface deactivated flashes at 2 Hz flashes at 8 Hz off off flashes at 8 Hz interface activated, antenna off interface activated, tag not in the field interface activated, tag in the field overload, short-circuit or communicati error interface in DP master not cfigured UK Special device- LED indicatis LED Status Note green AUX LED yellow AUX LED flashes at 8 Hz yellow IO1...IO4 LEDs flash at 8 Hz green AUX LED yellow AUX LED flashes at 8 Hz green IO1...IO4 LEDs flash at 8 Hz yellow IO1...IO4 LEDs flash at 8 Hz Device is in the service mode "emergency system started". Major error, device has to be returned. A firmware update is necessary and can be executed via the web server. Hardware fault or permanent data in the device are corrupt. 19

20 LED Status Note green AUX LED yellow AUX LED flashes at 8 Hz Reset to factory settings - yellow IO3 LED flashes at 8 Hz 8 Diagnosis Errors occurring during operati can be evaluated via the Profibus DP diagnostics and via the LED status indicatis (chapter 7). 9 Technical data 9.1 Data sheets Data sheets can be found at: data sheet search DTE Device manual The device manual can be found at: data sheet search DTE100 operating instructis 10 Maintenance, repair and disposal Dispose of the device in accordance with the natial envirmental regulatis. 11 Approvals/standards The EC declarati of cformity and approvals can be found at: data sheet search DTE100 Approvals 20

21 12 Scale drawing 85 46, ,2 UK M12x1 M4 57,5 115 M12x1 43,5 21