MODEL NO.: N154I3-L03

Transcription

1 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) TFT LCD Specification MODEL NO. N54I3-L3 Customer Approved by Note 記錄工作審核角色投票 CST PMMD Director Kj_cheng( 鄭光容 /5655/5449/47) Director Accept / 3 Version.

2 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) - CONTENTS - REVISION HISTORY GENERAL DESCRIPTION OVERVIEW.2 FEATURES.3 APPLICATION.4 GENERAL SPECIFICATIONS.5 MECHANICAL SPECIFICATIONS 2. ABSOLUTE MAXIMUM RATINGS ABSOLUTE RATINGS OF ENVIRONMENT 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2. TFT LCD MODULE BACKLIGHT UNIT 3. ELECTRICAL CHARACTERISTICS TFT LCD MODULE 3.2 BACKLIGHT UNIT 4. BLOCK DIAGRAM TFT LCD MODULE 4.2 BACKLIGHT UNIT 5. INPUT TERMINAL PIN ASSIGNMENT TFT LCD MODULE 5.2 BACKLIGHT UNIT 5.3 TIMING DIAGRAM OF LVDS INPUT SIGNAL 5.4 COLOR DATA INPUT ASSIGNMENT 5.5 EDID DATA STRUCTURE 5.6 EDID SIGNAL SPECIFICATION 6. INTERFACE TIMING INPUT SIGNAL TIMING SPECIFICATIONS 6.2 POWER ON/OFF SEQUENCE 7. OPTICAL CHARACTERISTICS TEST CONDITIONS 7.2 OPTICAL SPECIFICATIONS 8. PRECAUTIONS HANDLING PRECAUTIONS 8.2 STORAGE PRECAUTIONS 8.3 OPERATION PRECAUTIONS 9. PACKING CARTON 9.2 PALLET FOR SEA FREIGHT 9.3 PALLET FOR AIR FREIGHT. DEFINITION OF LABELS CMO MODULE LABEL.2 CARTON LABEL 2 / 3 Version.

3 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) REVISION HISTORY Page Version Date Section Description (New) Ver. Jun.27, 27 All All specification first issued. 3 / 3 Version.

4 . GENERAL DESCRIPTION. OVERVIEW Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) N54I3-L3 is a 5.4 TFT Liquid Crystal Display module with single CCFL Backlight unit and 3 pins LVDS interface. This module supports 28 x 8 Wide-XGA mode and can display 262,44 colors. The optimum viewing angle is at 6 o clock direction. The inverter module for Backlight is not built in..2 FEATURES - Thin and light weight - WXGA (28 x 8 pixels) resolution - 3.3V LVDS (Low Voltage Differential Signaling) interface with pixel/clock.3 APPLICATION - TFT LCD Notebook.4 GENERAL SPECIFICATINS Item Specification Unit Note Active Area 33.2 (H) x 27. (V) (5.4 diagonal) mm Bezel Opening Area (H) x 2.5 (V) mm () Driver Element a-si TFT active matrix - - Pixel Number 28 x R.G.B. x 8 pixel - Pixel Pitch.2588 (H) x.2588 (V) mm - Pixel Arrangement RGB vertical stripe - - Display Colors 262,44 color - Transmissive Mode Normally white - - Surface Treatment Hard coating (3H), Glare MECHANICAL SPECIFICATIONS Item Min. Typ. Max. Unit Note Horizontal(H) mm Module Size Vertical(V) mm () Thickness(T) mm Weight g - Note () Please refer to the attached drawings for more information of front and back outline dimensions. 4 / 3 Version.

5 2. ABSOLUTE MAXIMUM RATINGS 2. ABSOLUTE RATINGS OF ENVIRONMENT Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) Item Symbol Value Min. Max. Unit Note Storage Temperature T ST ºC () Operating Ambient Temperature T OP +5 ºC (), (2) Shock (Non-Operating) S NOP - 22/2 G/ms (3), (5) Vibration (Non-Operating) V NOP -.5 G (4), (5) Note () Note (2) -4 Temperature and relative humidity range is shown in the figure below. (a) 9 %RH Max. (Ta <= 4 ºC). (b) Wet-bulb temperature should be 39 ºC Max. (Ta > 4 ºC). (c) No condensation. The temperature of panel surface area should be ºC min. and 5 ºC max. Note (3) time for ± X, ± Y, ± Z. for Condition (22G / 2ms) is half Sine Wave,. Note (4) ~5 Hz, 3 min/cycle, cycle for X,Y,Z-axis. Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. The fixing condition is shown as below At Room Temperature Side Mount Fixing Screw Relative Humidity (%RH) Operating Range Storage Range Temperature (ºC) LCD Module 6 8 Side Mount Fixing Screw Stage Gap=2mm Bracket 5 / 3 Version.

6 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2. TFT LCD MODULE Item Symbol Value Min. Max. Unit Power Supply Voltage Vcc V Logic Input Voltage V IN -.3 Vcc+.3 V BACKLIGHT UNIT Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) Value Item Symbol Unit Note Min. Max. Lamp Voltage V L - 2.5K V RMS (), (2), I L = 6. ma Lamp Current I L ma RMS (), (2) Lamp Frequency F L 5 8 KHz Note () Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for lamp (Refer to Section 3.2 for further information). Note () 6 / 3 Version.

7 3. ELECTRICAL CHARACTERISTICS Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) 3. TFT LCD MODULE Ta = 25 ± 2 ºC Parameter Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage Vcc V - Ripple Voltage V RP - - mv - Rush Current I RUSH A (2) Initial Stage Current I IS - -. A (2) Power Supply Current White - (32) ma (3)a lcc Black - (38) ma (3)b LVDS Differential Input High Threshold V TH(LVDS) mv (5), V CM =.2V LVDS Differential Input Low Threshold V TL(LVDS) mv (5) V CM =.2V LVDS Common Mode Voltage V CM V (5) LVDS Differential Input Voltage V ID - 6 mv (5) Terminating Resistor R T - - Ohm - Power per EBL WG P EBL - TBD - W (4) Note () The ambient temperature is Ta = 25 ± 2 ºC. Note (2) I RUSH the maximum current when VCC is rising I IS the maximum current of the first ms after power-on Measurement Conditions Shown as the following figure. Test pattern black. (High to Low) (Control Signal) SW +2V C uf +3.3V R 47K R2 K Q VR 47K C2.uF 2SK475 Q2 2SK47 FUSE C3 uf Vcc (LCD Module Input) V Vcc rising time is 47us 47us.Vcc +3.3V ms VCC I RUSH I IS ICC 7 / 3 Version.

8 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, DC Current and f v = 6 Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern Note (4) The specified power are the sum of LCD panel electronics input power and the inverter input power. Test conditions are as follows. (a) Vcc = 3.3 V, Ta = 25 ± 2 ºC, f v = 6 Hz, (b) The pattern used is a black and white 32 x 36 checkerboard, slide # from the VESA file Flat Panel Display Monitor Setup Patterns, FPDMSU.ppt. (c) Luminance 6 nits. (d) The inverter used is provided from Sumida. Note (5) The parameters of LVDS signals are defined as the following figures. Single Ended Active Area VCM V b. Black Pattern Active Area Differential V TH(LVDS) V V TL(LVDS) VID VID 8 / 3 Version.

9 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) 3.2 BACKLIGHT UNIT Ta = 25 ± 2 ºC Parameter Symbol Value Min. Typ. Max. Unit Note Lamp Input Voltage V L V RMS I L = 6. ma Lamp Current I L 2. (),(2) (6.) (7.) ma 3. RMS (),(3) Lamp Turn On Voltage V S - - 4(25 o C) V RMS (4) ( o C) V RMS (4) Operating Frequency F L 5-8 KHz (5) Lamp Life Time L BL 2, - - Hrs (7) Power Consumption P L W (6), I L = 6. ma Note () Lamp current is measured by utilizing a high frequency current meter as shown below LCD Module HV (Pink) LV (White) Note (2) for burst mode inverter design Note (3) for continuous mode inverter design 2 A Current Meter Inverter Note (4) The voltage shown above should be applied to the lamp for more than second after startup. Otherwise the lamp may not be turned on. Note (5) The lamp frequency may generate interference with horizontal synchronous frequency from the display, and this may cause line flow on the display. In order to avoid interference, the lamp frequency should be detached from the horizontal synchronous frequency and its harmonics as far as possible. Note (6) P L = I L V L Note (7) The lifetime of lamp is defined as the time when it continues to operate under the conditions at Ta = 25 ±2 o C and I L = 6. ma RMS until one of the following events occurs (a) When the brightness becomes 5% of its original value. (b) When the effective ignition length becomes 8% of its original value. (Effective ignition length is defined as an area that the brightness is less than 7% compared to the center point.) Note (8) The waveform of the voltage output of inverter must be area-symmetric and the design of the inverter must have specifications for the modularized lamp. The performance of the Backlight, such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for the lamp. All the parameters of an inverter should be carefully designed to avoid generating too much current leakage from high voltage output of the inverter. When designing or ordering the inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module should be operated in the same manners when it is installed in your instrument. The output of the inverter must have symmetrical (negative and positive) voltage waveform and 9 / 3 Version.

10 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) symmetrical current waveform.(unsymmetrical ratio is less than %) Please do not use the inverter, which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp. It shall help increase the lamp lifetime and reduce its leakage current. a. The asymmetry rate of the inverter waveform should be % below; b. The distortion rate of the waveform should be within 2 ± %; c. The ideal sine wave form shall be symmetric in positive and negative polarities. I p I -p * Asymmetry rate I p I p / I rms * % * Distortion rate I p (or I p ) / I rms / 3 Version.

11 4. BLOCK DIAGRAM 4. TFT LCD MODULE LVDS Display Data & Clock Vcc GND Data EDID CLK EDID V EDID VL INPUT CONNECTOR 4.2 BACKLIGHT UNIT LAMP CONNECTOR LVDS INPUT / TIMING CONTROLLER DC/DC CONVERTER & REFERENCE VOLTAGE GENERATOR EDID EEPROM Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) SCAN DRIVER IC TFT LCD PANEL DATA DRIVER IC BACKLIGHT UNIT HV (Pink) 2 LV (White) / 3 Version.

12 5. INPUT TERMINAL PIN ASSIGNMENT 5. TFT LCD MODULE Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) Pin Symbol Description Polarity Remark Vss Ground 2 Vcc Power Supply +3.3 V (typical) 3 Vcc Power Supply +3.3 V (typical) 4 V EDID DDC 3.3V Power DDC 3.3V Power 5 NC Non-Connection 6 CLK EDID DDC Clock DDC Clock 7 DATA EDID DDC Data DDC Data 8 Rxin- LVDS Differential Data Input Negative R~R5,G 9 Rxin+ LVDS Differential Data Input Positive Vss Ground Rxin- LVDS Differential Data Input Negative G~G5, B, B 2 Rxin+ LVDS Differential Data Input Positive 3 Vss Ground 4 Rxin2- LVDS Differential Data Input Negative B2~B5, DE, Hsync, Vsync 5 Rxin2+ LVDS Differential Data Input Positive 6 Vss Ground 7 CLK- LVDS Clock Data Input Negative 8 CLK+ LVDS Clock Data Input Positive LVDS Level Clock 9 Vss Ground 2 NC Non-Connection 2 NC Non-Connection 22 Vss Ground 23 NC Non-Connection 24 NC Non-Connection 25 Vss Ground 26 NC Non-Connection 27 NC Non-Connection 28 Vss Ground 29 NC Non-Connection 3 NC Non-Connection Note () Connector Part No. HRS MDF76KBW-3S-H(58) or equivalent Note (2) User s connector Part No FI-X3M or equivalent Note (3) The first pixel is odd as shown in the following figure. 2 / 3 Version.

13 5.2 BACKLIGHT UNIT Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) Pin Symbol Description Color HV High Voltage Pink 2 LV Ground White Note () Connector Part No. JST-BHSR-2VS- or equivalent Note (2) User s connector Part No. JST-SM2B-BHSS--TB or equivalent 5.3 TIMING DIAGRAM OF LVDS INPUT SIGNAL CLK+ Rxin2 Rxin Rxin T/7 IN2 IN9 IN8 IN7 IN6 IN5 IN4 DE Vsync Hsync B5 B4 B3 B2 IN3 IN2 IN IN IN9 IN8 IN7 B B G5 G4 G3 G2 G IN6 IN5 IN4 IN3 IN2 IN IN G R5 R4 R3 R2 R R Signal for DCLK Cycle (T) 3 / 3 Version.

14 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) 4 / 3 Version. 5.4 COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input for the color. The higher the binary input the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R5 R4 R3 R2 R R G5 G4 G3 G2 G G B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red()/Dark Red() Red(2) Red(6) Red(62) Red(63) Gray Scale Of Green Green()/Dark Green() Green(2) Green(6) Green(62) Green(63) Gray Scale Of Blue Blue()/Dark Blue() Blue(2) Blue(6) Blue(62) Blue(63) Note () Low Level Voltage, High Level Voltage

15 5.5 EDID DATA STRUCTURE 5 / 3 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) The EDID (Extended Display Identification Data) data formats are to support displays as defined in the VESA Plug & Display and FPDI standards. Byte Byte #(decimal)#(hex)field Name and Comments Value(hex) Value(binary) Header Header FF 2 2 Header FF 3 3 Header FF 4 4 Header FF 5 5 Header FF 6 6 Header FF 7 7 Header 8 8 EISA ID manufacturer name ( CMO ) D 9 9 EISA ID manufacturer name (Compressed ASCII) AF A ID product code (N54I3-L3) 54 B ID product code (hex LSB first; N54I3-L3) 5 2 C ID S/N (fixed ) 3 D ID S/N (fixed ) 4 E ID S/N (fixed ) 5 F ID S/N (fixed ) 6 Week of manufacture (fixed H ) 7 Year of manufacture (fixed H ) 8 2 EDID structure version # ( ) 9 3 EDID revision # ( 3 ) Video I/P definition ( digital ) Max H image size ( 33cm ) Max V image size ( 2cm ) Display Gamma (Gamma = 2.2 ) Feature support ( Active off, RGB Color ) A 25 9 Red/Green (Rx, Rx, Ry, Ry, Gx, Gx, Gy, Gy) 6 26 A Blue/White (Bx, Bx, By, By, Wx, Wx, Wy, Wy) A 27 B Red-x (Rx =.62 ) 9A 28 C Red-y (Ry =.34 ) D Green-x (Gx =.36 ) 4E 3 E Green-y (Gy =.53 ) 87 3 F Blue-x (Bx =.5 ) Blue-y (By =.2 ) E 33 2 White-x (Wx =.33 ) White-y (Wy =.329 ) Established timings Established timings Manufacturer s reserved timings Standard timing ID # Standard timing ID # Version.

16 6 / 3 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) 4 28 Standard timing ID # Standard timing ID # A Standard timing ID # B Standard timing ID # C Standard timing ID # D Standard timing ID # E Standard timing ID # F Standard timing ID # Standard timing ID # Standard timing ID # Standard timing ID # Standard timing ID # Standard timing ID # Standard timing ID # 8 Detailed timing description # Pixel clock ( 7MHz, According to VESA CVT Rev.) BC # Pixel clock (hex LSB first) B # H active ( 28 ) # H blank ( 6 ) A 58 3A # H active H blank ( 28 6 ) B # V active ( 8 ) 2 6 3C # V blank ( 23 ) 7 6 3D # V active V blank ( 8 23 ) E # H sync offset ( 48 ) F # H sync pulse width ("32 ) # V sync offset V sync pulse width ( 3 6 ) 36 # H sync offset H sync pulse width V sync offset V sync width 65 4 ( ) # H image size ( 33 mm ) 4B # V image size ( 27 mm ) CF # H image size V image size ( ) # H boarder ( ) 7 46 # V boarder ( ) # Non-interlaced, Normal, no stereo, Separate sync, H/V pol 7 47 Negatives Detailed timing description # # 2 Flag 74 4A # 2 Reserved 75 4B # 2 FE (hex) defines ASCII string (Model Name N54I3-L3, ASCII) FE 76 4C # 2 Flag 77 4D # 2 st character of name ( N ) 4E 78 4E # 2 2nd character of name ( ) F # 2 3rd character of name ( 5 ) # 2 4th character of name ( 4 ) # 2 5th character of name ( I ) # 2 6th character of name ( 3 ) # 2 7th character of name ( - ) 2D Version.

17 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) # 2 8th character of name ( L ) 4C # 2 9th character of name ( ) # 2 9th character of name ( 3 ) # 2 New line character indicates end of ASCII string A # 2 Padding with Blank character # 2 Padding with Blank character 2 9 5A Detailed timing description # 3 9 5B # 3 Flag 92 5C # 3 Reserved 93 5D # 3 FE (hex) defines ASCII string (Vendor CMO, ASCII) FE 94 5E # 3 Flag 95 5F # 3 st character of string ( C ) # 3 2nd character of string ( M ) 4D 97 6 # 3 3rd character of string ( O ) 4F # 3 New line character indicates end of ASCII string A # 3 Padding with Blank character 2 64 # 3 Padding with Blank character 2 65 # 3 Padding with Blank character # 3 Padding with Blank character # 3 Padding with Blank character # 3 Padding with Blank character # 3 Padding with Blank character 2 6 6A # 3 Padding with Blank character 2 7 6B # 3 Padding with Blank character 2 8 6C Detailed timing description # 4 9 6D # 4 Flag 6E # 4 Reserved 6F # 4 FE (hex) defines ASCII string (Model Name N54I3-L3, ASCII) FE 2 7 # 4 Flag 3 7 # 4 st character of name ( N ) 4E 4 72 # 4 2nd character of name ( ) # 4 3rd character of name ( 5 ) # 4 4th character of name ( 4 ) # 4 5th character of name ( I ) # 4 6th character of name ( 3 ) # 4 7th character of name ( - ) 2D 2 78 # 4 8th character of name ( L ) 4C 2 79 # 4 9th character of name ( ) A # 4 9th character of name ( 3 ) B # 4 New line character indicates end of ASCII string A 24 7C # 4 Padding with Blank character D # 4 Padding with Blank character E Extension flag 27 7F Checksum 34 7 / 3 Version.

18 6. INTERFACE TIMING 6. INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) Signal Item Symbol Min. Typ. Max. Unit Note DCLK Frequency /Tc MHz (2) Vertical Total Time TV TH - Vertical Active Display Period TVD TH - DE Vertical Active Blanking Period TVB TV-TVD 23 TV-TVD TH Horizontal Total Time TH Tc (2) Horizontal Active Display Period THD Tc (2) Horizontal Active Blanking Period THB TH-THD 6 TH-THD Tc (2) Note () Because this module is operated by DE only mode, Hsync and Vsync are ignored. (2) channels LVDS input. DE DCLK DE DATA TC INPUT SIGNAL TIMING DIAGRAM TVD Tv TH THD 8 / 3 Version.

19 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) 6.2 POWER ON/OFF SEQUENCE Power On Power Off Restart - Power Supply for LCD, Vcc - Interface Signal (LVDS Signal of Transmitter), V I - Power for Lamp Timing Specifications.5< t <= msec < t2 <= 5 msec < t3 <= 5 msec t4 >= 5 msec t5 >= 2 msec t6 >= 2 msec Note () Please follow the power on/off sequence described above. Otherwise, the LCD module might be damaged. V V % 9% Note (2) Please avoid floating state of interface signal at invalid period. When the interface signal is invalid, be sure to pull down the power supply of LCD Vcc to V. Note (3) The Backlight inverter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight inverter power must be turned off before the power supply for the logic and the interface signal is invalid. t OFF t2 t5 5% Valid Data ON Note (4) Sometimes some slight noise shows when LCD is turned off (even backlight is already off). To avoid this phenomenon, we suggest that the Vcc falling time is better to follow 5ms t7 3 ms. 9% t6 t3 5% t7 OFF % t4 % 9 / 3 Version.

20 7. OPTICAL CHARACTERISTICS 7. TEST CONDITIONS Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) Item Symbol Value Unit Ambient Temperature Ta 25±2 o C Ambient Humidity Ha 5± %RH Supply Voltage V CC 3.3 V Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS" Inverter Current I L 6. ma Inverter Driving Frequency F L 6 KHz Inverter Sumida-H5-495 The measurement methods of optical characteristics are shown in Section 7.2. The following items should be measured under the test conditions described in Section 7. and stable environment shown in Note (6). 7.2 OPTICAL SPECIFICATIONS Item Symbol Condition Min. Typ. Max. Unit Note Contrast Ratio CR (2), (5) Response Time T R ms T F ms (3) Average Luminance of White LAVE cd/m 2 (4), (5) Rx.56 - Red Ry.33 - θ Gx x =, θ Y =.3 - Green Viewing Normal Angle Gy TYP..56 TYP. - Color () Bx Chromaticity Blue By.55 - White Wx.33 - Wy Color Gamut C.G % (7) Viewing Angle θ x Horizontal θ x CR θ Y Vertical θ Y Deg. (),(5) White Variation of 5 Points δw 5p % θ x =, θ Y = White Variation of 3 Points % (5),(6) δw 3p 2 / 3 Version.

21 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) Note () Definition of Viewing Angle (θx, θy) Normal θx = θy = º 6 o clock θy- = 9º Note (2) Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L63 / L L63 Luminance of gray level 63 L Luminance of gray level CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6). Note (3) Definition of Response Time (T R, T F ) % 9% % % θx- = 9º x- θy- θx θy+ θx+ y+ 2 o clock direction θy+ = 9º y- x+ Gray Level 63 Gray Level 63 Gray Level Time θx+ = 9º Optical Response T R T F ms ms 2 / 3 Version.

22 Note (4) Definition of Average Luminance of White (L AVE ) Measure the luminance of gray level 63 at 5 points L AVE = [L ()+ L (2)+ L (3)+ L (4)+ L (5)] / 5 L (x) is corresponding to the luminance of the point X at Figure in Note (6) Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) Note (5) Measurement Setup The LCD module should be stabilized at given temperature for 2 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 2 minutes in a windless room. LCD Module LCD Panel USB2 Center of the Screen 5 mm CS-T Light Shield Room (Ambient Luminance < 2 lux) 22 / 3 Version.

23 Note (6) Definition of White Variation (δw) H/4 H H/4 H/4 H/4 Measure the luminance of gray level 63 at 5 points Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) δw 5p = Minimum [L ()+ L ()+ L (2)+ L (3)+ L (5)] / Maximum [L ()+ L ()+ L (2)+ L (3)+ L (5)] δw 3p = Minimum [L () ~ L (3)] / Maximum [L () ~ L (3)] mm mm mm W/4 W/4 W/4 W/4 W mm Active area Note (7) Definition of color gamut (C.G%) C.G%= R G B / R G B,*% R, G, B color coordinates of red, green, and blue defined by NTSC, respectively. R, G, B color coordinates of module on 63 gray levels of red, green, and blue, respectively. R G B area of triangle defined by R, G, B R G B area of triangle defined by R, G, B G G CIE 93.2 B. B R R Test Point X= to 3 X 23 / 3 Version.

24 8. PRECAUTIONS 8. HANDLING PRECAUTIONS Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) () The module should be assembled into the system firmly by using every mounting hole. Be careful not to twist or bend the module. (2) While assembling or installing modules, it can only be in the clean area. The dust and oil may cause electrical short or damage the polarizer. (3) Use fingerstalls or soft gloves in order to keep display clean during the incoming inspection and assembly process. (4) Do not press or scratch the surface harder than a HB pencil lead on the panel because the polarizer is very soft and easily scratched. (5) If the surface of the polarizer is dirty, please clean it by some absorbent cotton or soft cloth. Do not use Ketone type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It might permanently damage the polarizer due to chemical reaction. (6) Wipe off water droplets or oil immediately. Staining and discoloration may occur if they left on panel for a long time. (7) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contacting with hands, legs or clothes, it must be washed away thoroughly with soap. (8) Protect the module from static electricity, it may cause damage to the C-MOS Gate Array IC. (9) Do not disassemble the module. () Do not pull or fold the lamp wire. () Pins of I/F connector should not be touched directly with bare hands. 8.2 STORAGE PRECAUTIONS () High temperature or humidity may reduce the performance of module. Please store LCD module within the specified storage conditions. (2) It is dangerous that moisture come into or contacted the LCD module, because the moisture may damage LCD module when it is operating. (3) It may reduce the display quality if the ambient temperature is lower than ºC. For example, the response time will become slowly, and the starting voltage of lamp will be higher than the room temperature. 8.3 OPERATION PRECAUTIONS () Do not pull the I/F connector in or out while the module is operating. (2) Always follow the correct power on/off sequence when LCD module is connecting and operating. This can prevent the CMOS LSI chips from damage during latch-up. (3) The startup voltage of Backlight is approximately Volts. It may cause electrical shock while assembling with inverter. Do not disassemble the module or insert anything into the Backlight unit. 24 / 3 Version.

25 9. PACKING 9. CARTON Figure. 9- Packing method Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) 25 / 3 Version.

26 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) 9.2 PALLET FOR SEA FREIGHT Figure. 9-2 Packing method 26 / 3 Version.

27 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) 9.3 PALLET FOR AIR FREIGHT Figure. 9-3 Packing method 27 / 3 Version.

28 . DEFINITION OF LABELS. CMO MODULE LABEL Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339) The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. N54I3 -L3 Rev. XX (a) Model Name N54I3 - L3 (b) Revision Rev. XX, for example C, C2 etc. (c) Serial ID X X X X X X X Y M D L N N N N Serial No. Product Line Year, Month, Date CMO Internal Use Revision CMO Internal Use Serial ID includes the information as below (a) Manufactured Date Year ~9, for 2~29 Month ~9, A~C, for Jan. ~ Dec. Day ~9, A~Y, for st to 3 st, exclude I, O and U (b) Revision Code cover all the change (c) Serial No. Manufacturing sequence of product (d) Product Line -> Line, 2 -> Line 2, etc. LEOO 28 / 3 Version.

29 Doc No Issued Date June. 27, 27 Model No. N54I3-L3 (NF4I339).2 CARTON LABEL 29 / 3 Version.

30