FUJITSU SEMICONDUCTOR SUPPORT SYSTEM SS E DSU-FR EMULATOR F 2 MC-16FX EXPANSION TRACE BOARD MB E OPERATION MANUAL

Transcription

1 FUJITSU SEMICONDUCTOR SUPPORT SYSTEM SS E DSU-FR EMULATOR F 2 MC-16FX EXPANSION TRACE BOARD MB E OPERATION MANUAL

2 PREFACE Thank you for purchasing the DSU-FR* 1 emulator F 2 MC* 2-16FX expansion trace board (model number: MB E)* 3. This product is used to connect a Fujitsu F 2 MC-16FX family microcontroller MB96V300 (BGA-416P) to a DSU-FR emulator (model number: MB )* 4 and DSU-FR emulator F 2 MC-16FX BGA-416P adapter (model number: MB )* 5. This document describes how to handle the DSU-FR emulator F 2 MC-16FX expansion trace board. Be sure to read this document before using the product. For details on the mass production MCUs and evaluation MCUs supported by this product, consult with sales or support representative. *1 : FR, the abbreviation of FUJITSU RISC controller, is a line of products of FUJITSU Limited. *2 : F 2 MC is the abbreviation of FUJITSU Flexible Microcontroller. *3 : Referred to as the trace board in this manual. *4 : Referred to as the emulator in this manual. *5 : Referred to as the adapter in this manual. Safe use of this Product This manual contains important information regarding how to use this product safely. Be sure to read this manual before using the adapter, and to follow the directions given in this manual in order to use the product correctly. In particular, thoroughly read the "Safety Precautions" at the start of this manual and perform a full safety check before using this product. After reading the manual, keep it handy for future reference. Warranties and Liability The specifications of the adapter are subject to change without notice. Note that Fujitsu shall accept no responsibility for any consequences arising either directly or indirectly from the use of this product. Product Operating Environment Use the product at an operating temperature of between 5 C and 35 C and at an operating humidity of between 20% to 80%. Use the product in an environment that is free of condensation and avoid high temperature or humidity. This product consists of a printed circuit board unit without casing with all electronic components exposed. Accordingly, do not place other objects on top of the circuit board and do not allow the metal parts of the unit to come into contact with people or materials that may include static electricity. Similarly, keep any objects that are flammable, likely to cause a short circuit, or cause any other such problem well away from the unit when the power to the unit is turned on. Use the product as horizontal as possible and avoid operating it at a place exposed to strong vibration, dust, or explosive gas. If the unit is used in an environment that does not satisfy the above guidelines, there is a risk of unexpected damage to property or injury to the user or other people in the vicinity. You should also keep the packaging materials used for shipping the product. These are useful if the product needs to be re-shipped again, for example, if it becomes faulty and needs to be repaired. Related Manuals Refer to the following manuals in conjunction with this manual. DSU-FR EMULATOR MB HARDWARE MANUAL DSU-FR EMULATOR BGA-416P ADAPTER MB OPERATION MANUAL DSU-FR EMULATOR QFP-100P HEADER TYPE3 MB OPERATION MANUAL i

3 European RoHS compliance Products with a -E suffix on the part number are European RoHS compliant products. Notice on this document All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice. Please confirm the latest relevant information with the sales representatives. ii

4 Cautions of the Products Described in this Document The following precautions apply to the products described in this manual. Warning Electric shock, Damage Electric shock, Damage Indicates a potentially hazardous situation which could result in death or serious injury and/or a fault in the user s system if not avoided appropriately. Before performing any operation described in this manual, turn off all the power supplies to the system. Performing such an operation with the power on may cause an electric shock or device fault. Once the product has been turned on, do not touch any metal part of it. Doing so may cause an electric shock or device fault. Caution Cuts, Damage Cuts Damage Damage Damage Damage Damage Damage Indicates the presence of a hazard that may cause a minor or moderate injury, damages to this product or devices connected to it, or may cause to loose software resources and other properties such as data, if the device is not used appropriately. Before moving the product, be sure to turn off all the power supplies and remove it from the adapters. Watch your step when carrying the product. Do not use the product in an unstable location such as a place exposed to strong vibration or a sloping surface. Doing so may cause the product to fall, resulting in an injury or fault. This product has sharp edges that are left unavoidably exposed. Take care when handling the product to avoid being injured by these sharp edges. Do not place anything on the product or expose the product to physical shocks. Do not carry the product after the power has been turned on. Doing so may cause a malfunction due to overloading or shock. Since the product contains many electronic components, keep it away from direct sunlight, high temperature, and high humidity to prevent condensation. Do not use or store the product where it is exposed to much dust or a strong magnetic or electric field for an extended period of time. Inappropriate operating or storage environments may cause a fault. Use the product within the ranges given in the specifications. Operation over the specified ranges may cause a fault. To prevent electrostatic breakdown, do not let your finger or other object come into contact with the metal parts of any of the connectors. Before handling the product, touch a metal object (such as a door knob) to discharge any static electricity from your body. When turning the power on or off, follow the relevant procedure as described in this document. Before turning the power on, in particular, be sure to finish making all the required connections. Furthermore, be sure to configure and use the product by following the instructions given in this document. Using the product incorrectly or inappropriately may cause a fault. Because the product has no casing, it is recommended that it be stored in the original packaging. Transporting the product may cause a damage or fault. Therefore, keep the packaging materials and use them when re-shipping the product. iii

5 The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU semiconductor device; FUJITSU does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU or any third party or does FUJITSU warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Copyright 2008 FUJITSU LIMITED All rights reserved iv

6 1. Product Overview Overview This product is an external trace board that provides a maximum capacity of 2 Gbytes (64 bits 256 Mframe) of external trace functionality. The trace board is used by connecting to the F 2 MC-16FX BGA-416P adapter (model number: MB ),which connects the DSU-FR Emulator (model number: MB , referred to as the emulator in this manual) to a user system using a Fujitsu F 2 MC-16FX family microcontroller. This product is an optional product for the DSU-FR emulator that assists the development of user systems that use a Fujitsu F 2 MC-16FX family microcontroller. Verifying the Contents of the Package Check that all of the following components are present in the package before using the trace board. Trace board :1 AC adapter :1 Locking screws :1 set (2 screws) Operation manual (English: this manual) :1 Operation manual (Japanese) :1 Related Products The optional products shown in Table 1 are available for the adapter. Purchase these separately as needed. Table 1 Optional Parts Name Part number DSU-FR emulator F 2 MC-16FX BGA-416P adapter F 2 MC-16FX QFP-100P header type3 MB MB MB Evaluation MCU* MB96V300 * : The evaluation MCU is used connected to the adapter. Consult with sales or support representative for details on compatible evaluation MCUs. 1

7 System Configuration The trace board is used in combination with the emulator, adapter, header board, and other components. These are used connected to the user system. A schematic of the system configuration of this product is shown in Figure 1. Host computer General-purpose measurement device AC in External trigger/program execution AC adapter RS232C, USB, LAN AC Adapter for the Emulator DSU-FR emulator AC in AC adapter AC adapter for the trace board (Supplied with this product) Trace board (this product) Trace board Evaluation MCU (MB96V300) Adapter board Adapter Flat cable User system Header board Header Figure 1 System configuration schematic A host computer and emulator debugger software need to be purchased separately to use the emulator. See "3. Connection" for details on how to connect the adapter and the header board. See the hardware manual and operation manual of the emulator and adapter for the specifications of these components. 2

8 External Appearance and Component Names The external appearance of the adapter board is shown in Figure 2 and the component names are shown in Figure 3. C130 C128 C118 C116 R496 R480 R497 R498 R481 R482 GND RN16 R499 M41 R483 M37 (3) RN18 GND ADAPTER BOARD POWER ON D4 R S1 1 9 R159 R158 C42 R187 R R500 R501 R502 R503 R520 R521 R522 R523 R524 R525 C127 C126 C129 M40 R484 R485 R486 R487 R536 R537 R538 R539 R540 R541 C137 C139 C117 M44 M2 R52 R44 R54 R55 R57 R56 R58 R59 R61 M R526 R527 C106 C105 C125 R542 R543 C93 C92 C138 (1) (2) 160 CN1 159 ADAPTER-BOARD CN RN2 RN1 INITDONE MSEL0 RN9 RN12 MSEL1 RN11 R154 RN8 RN7 22 R63 R65 R67 R69 R71 R73 R38 R39 R13 R14 M1 R8 R9 AB R6 R7 R2 R3 R51 R50 R49 R60 R68 R70 R79 R77 X1 R157 R103 R109 R106 R105 A R117 R108 R112 R115 1 R116 R110 T0 T2 R113 R114 RN6 RN4 C4 RN5 RN3 T1 T3 RN10 CRCERR R126 R131 R127 R130 R125 R120 R124 R121 R126 R128 R133 R129 R132 R123 R118 R122 R119 R128 R111 R153 R93 R150 R51 M3 C40 R185 R183 R184 R M C38 R181 R179 R180 R M10 R436 R437 R438 R439 M33 R440 R441 R442 R443 C103 C102 C104 R456 R457 R458 R459 M32 R460 R461 R462 R463 C82 C81 C104 R374 R375 R368 R369 M25 R372 R373 R370 R371 C79 C78 C80 R416 R417 R418 R419 M29 R421 R423 R426 R427 C115 C113 C94 R472 R473 R474 R475 M36 R476 R477 R478 R479 C69 C68 C114 R352 R353 R354 R355 M25 R358 R359 R356 R357 C91 C89 C70 RN V 1 4 R392 R408 C32 FL1 L3 C33 C35 RN20 GND R177 R176 R393 R394 R395 R396 R397 R398 M24 R410 R409 R412 R413 R411 R415 M28 R399 C58 C57 C77 R414 C46 C45 C90 D3 Q1 (4) R162 R161 D5 AC ADAPTER R163 POWER ON R164 R166 R168 D1 M6 M5 M4 D2 M8 R171 L1 L V RN V RN14 C36 R175 R M9 1 4 R173 R172 R335 R336 R337 R338 R339 R340 R341 R342 R285 R286 R279 M17 C55 C54 C56 R263 R264 R265 R266 M13 R267 R268 R269 R270 C65 C67 C44 R301 R302 R295 R280 M16 R296 M20 RN19 GND C27 10 M7 C29 R281 R282 R283 R284 C53 R297 R298 R299 R300 C66 GND RN17 No. Description Function (1) Trace board fixing bracket A bracket for connecting the trace board to the adapter. (2) Expansion trace connector A connector that connects to the adapter. The power supply to the trace board is supplied via this connector from the AC adapter connected to the adapter board. (3) Adapter power LED Lights up when the adapter power is on. (4) Trace board power LED Lights up when then trace board power is on. The power to the trace board is turned on by connecting the supplied AC adapter. There is no power switch. Figure 2 External appearance (component side) 3

9 C124 C136 R495 R511 R494 R493 R510 R509 M39 R492 M43 R508 R491 R490 R489 R507 R506 R505 C133 C122 C123 R488 C121 C134 C135 R504 R535 R519 R524 R533 R518 R517 R253 M42 R532 M38 R516 C100 C131 C132 M31 C109 C98 C99 M34 C76 C107 C108 M23 C85 C74 C75 M26 C52 C83 C84 M15 C59 C50 C51 R531 R530 R529 R528 R435 R434 R433 R432 R431 R430 R429 R428 R471 R470 R469 R468 R467 R466 R465 R464 R363 R362 R365 R364 R361 R360 R367 R366 R406 R407 R404 R405 R403 R402 R401 R400 R334 R333 R332 R331 R330 R329 R328 R327 RB2 RB7 RB8 RB1 C112 C119 C120 M35 C97 C110 C111 M30 C88 C95 C96 M27 C73 C86 C87 M22 C64 C71 C72 M19 C49 C62 C63 R515 R514 R513 R512 R451 R450 R449 R448 R447 R446 R445 R444 R455 R454 R453 R452 R425 R424 R422 R420 R383 R382 R381 R380 R379 R378 R377 R376 R391 R390 R389 R388 R387 R386 R385 R384 R350 R349 R348 R347 R346 R345 R344 R343 RB4 RB6 RB5 RB3 C43 C41 C39 C37 R72 R17 R19 R46 R45 R11 R12 R4 R53 R48 R62 R75 R81 R104 R100 R97 R101 R96 R86 R88 C1 R18 R20 R16 R15 R99 R94 R85 R87 C20 C2 R10 R83 R82 R152 R84 R24 R34 R41 R29 R40 R32 R25 R31 R22 R21 R35 R1 R5 C19 R43 R57 R66 R64 R74 R155 R107 R102 R98 R95 R156 R91 R89 R92 R90 R170 R23 R36 C18 C13 R135 R137 R42 C5 C10 C34 R28 R138 R140 R169 R139 R134 R136 R76 R37 R80 R78 R30 R27 R33 R26 C7 R141 C8 C11 R148 R149 C6 R146 R147 R145 R144 R143 R142 C26 C3 C9 C12 C17 C14 C21 C24 C16 C23 C15 R254 R252 R291 R278 R292 R289 R277 R276 C25 M18 R290 R287 R288 R293 M14 R275 R274 R273 R272 C28 R165 R167 C60 C61 R294 C47 C48 R271 C31 C30 Figure 3 External appearance(solder side) 4

10 2. Usage Cautions Adhere to the following precautions where using the trace board. Cautions The basic trace function on the adapter cannot be used when the trace board is connected to the adapter. When using the trace board, connect the AC adapter provided with the trace memory to the adapter. See "3. Connection Connecting the AC adapter" for details on how to connect the AC adapter. When the trace board is connected to the adapter, fix the two boards together using the locking screws. 3. Connection Connecting the Adapter See Figure 4 to connect the trace board. See the operation manual of the F 2 MC-16FX BGA-416P adapter (model number: MB ) and the F 2 MC-16FX QFP-100P header type3 (model number: MB ) for details on connecting the adapter and header to the user system. Trace board Adapter connector Adapter Flat cable connector Expansion trace connector Header Flat cables ( 2) Socket for Evaluation MCU Emulator connector Adapter Board Connector Locking screws ( 2) (Supplied with this product) Emulator User System Figure 4 Connecting the trace board 5

11 Connecting the AC Adapter See Figure 5 to connect the AC adapter. See the F 2 MC-16FX BGA-416P ADAPTER MB OPERATION MANUAL for the position of the DC jack. 1. Connect the AC cord to the AC adapter. 2. Connect the AC adapter to the adapter. 3. Insert the AC plug into a power outlet. Note : The power supply to the trace board is supplied by connecting the AC adapter to the adapter. As there is no power switch on the trace board, connect the AC adapter in the correct sequence within the power-on sequence. See "4 Operating Procedures Power-on Sequence and Power-off Sequence" for details on the poweron sequence. AC adapter DC jack Figure 5 Connecting the AC adapter 6

12 4. Operating Procedures This section describes the power-on and off sequences. Be sure to read this section before turning the power on. Power-on Sequence To turn the power on, follow the procedure shown in Figure 6 after making all devices connected. The emulator power can be turned on by pressing down the power switch on the rear of the emulator. The switch then remains in the depressed position. See the hardware manual of the emulator for details on the position of the power switch. The power to the adapter is turned on using the power switch on the adapter. See the F 2 MC-16FX BGA- 416P ADAPTER MB OPERATION MANUAL for the position of the power switch on the adapter. The emulator needs to be initialized (monitor loading) immediately before the power is turned on to the user system in a factory default state. See the SOFTUNE Workbench OPERATING MANUAL for details on the initialization procedure. Turn on the host computer Turn on the emulator The POWER LED on the emulator lights up Run SOFTUNE Workbench Run Emulator Debugger Has the emulator been initialized? YES NO Perform the emulator initialization Check that the dialog box is displayed (See Figure 7) Turn on the adapter Connect the AC adapter to the DC jack on the adapter to supply power to the trace board Click [OK] in the dialog box The adapter power LED on the trace board lights up The trace board power LED lights up Figure 6 Power-on sequence 7

13 Figure 7 Dialog box displayed Note : When the power is turned on to the user system, the adapter power LED on the trace board and the USER POWER LED on the adapter light up. Additionally, when the AC adapter is connected to the DC jack on the adapter, the Trace Board Power LED on the trace board lights up. If a LED does not light up when the power is turned on, quickly disconnect the power to the entire system, and turn the power on again after resolving the problem by checking such that there are no incorrect connections. Power-off Sequence Turn the power off by following the procedure shown in Figure 8. The emulator power can be turned off by pressing down and releasing the power switch on the rear of the emulator. The depressed switch then returns to the off position (the unpressed position). See the hardware manual of the emulator for details on the position of the power switch. Turn off the power to the adapter using the power switch on the adapter. See the "F 2 MC-16FX BGA- 416P Adapter MB Operation Manual" for the position of the power switch on the adapter. Exit Emulator Debugger Remove the AC adapter from the DC jack on the adapter to turn off the power to the trace board. Turn off the adapter power Turn off the power to the emulator Turn off the host computer (as required) Figure 8 Power-off sequence 8

14 5. Specifications 5. 1 General Specifications The general specifications of the trace board are shown in Table 2. Table 2 General Specifications Item Specification Remarks Product name Product model DSU-FR emulator F 2 MC-16FX expansion trace board MB E Memory capacity 2 GB 512Mbit SDRAM 32 Input power Maximum: +16V / 2.5A Supplied by adapter DC jack Operating voltage Operating frequency Operating temperature Storage temperature Operating humidity Storage humidity +3.3V: FPGA (I/O), SDRAM +1.2V: FPGA (internal) Max: 66MHz +5 C to +35 C 0 C to +70 C 20% to 80% 20% to 80% Generates +5V from +16V Generates +3.3V and +1.2V from +5V No condensation No condensation External dimensions 169.0mm(D) 139.0mm(W) 19.0mm(H) No chassis Weight 125.0g No chassis 5. 2 Function Specifications The function specifications of the trace board are shown in Table 3. Table 3 Trace Board Function Specifications Item Trace board function Description 64bit 256Mframe (2GB) trace memory function. The adapter connector specifications are shown in Table 4 and the pin assignment is shown in Table 5. Table 4 Adapter Connector Specifications Item Adapter connector Description Model: L (Manufactured by KEL). 160-pin right-angle connector 9

15 Connector pin number Pin name Table 5 Adapter Connector Pin Assignment Connector pin number Pin name Connector pin number Pin name Connector pin number Pin name 1 DC16V 41 TRDYX 81 TDT[30] 121 TDT[62] 2 DC16V 42 TOEX 82 TDT[31] 122 TDT[63] 3 DC16V 43 GND 83 GND 123 GND 4 DC16V 44 GND 84 GND 124 GND 5 DC16V 45 TDT[0] 85 TDT[32] 125 TAD[0] 6 DC16V 46 TDT[1] 86 TDT[33] 126 TAD[1] 7 MNT[0] 47 TDT[2] 87 TDT[34] 127 TAD[2] 8 MNT[1] 48 TDT[3] 88 TDT[35] 128 TAD[3] 9 MNT[2] 49 TDT[4] 89 TDT[36] 129 TAD[4] 10 MNT[3] 50 TDT[5] 90 TDT[37] 130 TAD[5] 11 MNT[4] 51 TDT[6] 91 TDT[38] 131 TAD[6] 12 MNT[5] 52 TDT[7] 92 TDT[39] 132 TAD[7] 13 GND 53 GND 93 GND 133 GND 14 GND 54 GND 94 GND 134 GND 15 MNT[6] 55 TDT[8] 95 TDT[40] 135 TAD[8] 16 MNT[7] 56 TDT[9] 96 TDT[41] 136 TAD[9] 17 MNT[8] 57 TDT[10] 97 TDT[42] 137 TAD[10] 18 MNT[9] 58 TDT[11] 98 TDT[43] 138 TAD[11] 19 MNT[10] 59 TDT[12] 99 TDT[44] 139 TAD[12] 20 MNT[11] 60 TDT[13] 100 TDT[45] 140 TAD[13] 21 MNT[12] 61 TDT[14] 101 TDT[46] 141 TAD[14] 22 MNT[13] 62 TDT[15] 102 TDT[47] 142 TAD[15] 23 GND 63 GND 103 GND 143 GND 24 GND 64 GND 104 GND 144 GND 25 MNT[14] 65 TDT[16] 105 TDT[48] 145 TAD[16] 26 MNT[15] 66 TDT[17] 106 TDT[49] 146 TAD[17] 27 MNT[16] 67 TDT[18] 107 TDT[50] 147 TAD[18] 28 MNT[17] 68 TDT[19] 108 TDT[51] 148 TAD[19] 29 MNT[18] 69 TDT[20] 109 TDT[52] 149 TAD[20] 30 MNT[19] 70 TDT[21] 110 TDT[53] 150 TAD[21] 31 MNT[20] 71 TDT[22] 111 TDT[54] 151 TAD[22] 32 EXTTRC 72 TDT[23] 112 TDT[55] 152 TAD[23] 33 GND 73 GND 113 GND 153 GND 34 GND 74 GND 114 GND 154 GND 35 TCLK 75 TDT[24] 115 TDT[56] 155 TAD[24] 36 EXTTRCX 76 TDT[25] 116 TDT[57] 156 TAD[25] 37 GND 77 TDT[26] 117 TDT[58] 157 TAD[26] 38 TADCSX 78 TDT[27] 118 TDT[59] 158 TAD[27] 39 TWRX 79 TDT[28] 119 TDT[60] 159 VCC 40 TEMUL 80 TDT[29] 120 TDT[61] 160 VCC 10

16 5. 3 Expansion Trace Memory AC Specifications DSU-side Trace Memory Write Timing Figure 9 shows the trace memory write timing as seen from the DSU side. TCLK WRITE TEMUL (1) (2) TRDYX TADSCX TWRX (3) (4) (3) (4) TOEX TAD[27:0] TDT[63:0] (3) (4) Address Data (5) (6) Symbol Description Min Max Units (1) TEMUL setup time 3 - ns (2) TEMUL hold time 3 - ns (3) TADSCX setup time 3 - ns (4) TADSCX hold time 3 - ns (5) Data setup time 3 - ns (6) Data hold time 3 - ns Figure 9 DSU-side trace memory write timing 11

17 DSU-side Trace Memory Read Timing Figure 10 shows the trace memory read timing as viewed from the DSU side. Note that the AC specifications vary depending on the voltage applied to VCC5. READ TCLK TEMUL TRDYX (7) (8) TADSCX (1) (2) TWRX TOEX (3) (4) (5) (6) TAD[27:0] Address TDT[63:0] Data (9) (10) Symbol Description Min Max Units (1) TADSCX setup time 3 - ns (2) TADSCX hold time 3 - ns (3) Address setup time 3 - ns (4) Address hold time 3 - ns (5) TOEX setup time 3 - ns (6) TOEX hold time 3 - ns (7) TRDYX setup time 3 - ns (8) TRDYX hold time 3 - ns (9) Data setup time 3 - ns (10) Data hold time 3 - ns Figure 10 DSU-side trace memory read timing 12

18 FUJITSU SEMICONDUCTOR SUPPORT SYSTEM DSU-FR EMULATOR F 2 MC-16FX EXPANSION TRACE BOARD MB E OPERATION MANUAL SS E February 2008 the first edition Published Edited FUJITSU LIMITED Electronic Devices Strategic Business Development Dept.

19