Space Duel 4 in 1 MultiVector INSTALL GUIDE
|
|
- Alaina Sullivan
- 5 years ago
- Views:
Transcription
1 Space Duel 4 in 1 MultiVector INSTALL GUIDE The Space Duel 4 in1 MultiVector kit includes four boards, the main board is pictured above and the CPU, Vector & ER2055 boards and cable below.
2 As you can see each connector set on the main board is labeled with the name of the PCB. The Space Duel PCB requires no modifications and is simply plugged into the lower set of connectors. You can use a Gravitar or Black Widow board in the upper set of connectors as marked. The CPU & Vector boards has ROM images of the Gravitar, Lunar Battle & Black Widow games. The ER2055 board allows for seperate game saves for these three games. The Space Duel board has its own ER2055 chip for games saves. Make sure you install the PCB s in the correct set of connectors. IMPORTANT INFORMATION PLEASE READ AND UNDERSTAND FULLY The MultiVector kit is a power & video switching backplane developed for Atari full size vector game boards. A Microcontroller & CPLD handle all control functions. The kit is designed for owners of Space Duel standup & cocktail games to allow for the addition of Gravitar or Black Widow PCB s to form a 2 board stack. Only one board is powered at any given time and is selectable through the control panel. Space Duel,Gravitar & Lunar Battle have similar controls so no additional buttons are required. However Black Widow has move & fire joysticks similar to Robotron so those two joysticks will need to be added to the Space Duel control panel. There is a 10 pin connector on the MultiVector main board so the joysticks can be wired into the control panel. ** Note that the select button in Space Duel is Player 2 in Gravitar & Lunar Battle* Some of the recommend tools for the install are pictured above.
3 The 10 pin connector P8 is shown in the picture below. The following is the pinout for the 10 pin connector. FIRE JOYSTICK MOVE JOYSTICK 1. Fire up 6. Ground 2. Fire down 7. Move up 3. Fire left 8. Move down 4. Fire right 9. Move left 5. Ground 10. Move right Two 5pin connector shells & ten pins are included in the kit for joystick wiring. **Note that the Move left & Move right function on the Move joystick can also be used as well as the Rotate left & Rotate right buttons on Space Duel, Gravitar & Lunar Battle.** Also in the picture above there is a two position dip switch for game default on power up. The settings are as follows. 1-ON 2-ON = SPACE DUEL 1-ON 2-OFF = GRAVITAR 1-OFF 2-ON = LUNAR BATTLE 1-OFF 2-OFF = BLACK WIDOW The MultiVector kit controls the power source to each of the PWB s through MOSFET transistors. These power sources are +5v, +10v, +22v & -22v and are fuse protected against short circuits which would damage the MOSFET s.
4 These fuses have sockets and are shown in the picture below. It is essential that any PWB s that are plugged into the MultiVector kit are working 100%. If there are any power issues with the boards you WILL blow one of these fuses. Take note of the current ratings for each power source 1.25 Amps for +10v,+22v & -22v. And 3.15 Amps for +5v, DO NOT mix these values into the wrong locations when replacing. The MultiVector kit has been tested for many hours to select the proper current ratings for these fuses, and are there to protect both the kit and your PWB s. The LED s are provided to monitor all power sources and indicate if any of the fuses are blown when the LED is not lit. If all 4 are lit then the power is good.
5 Gravitar or Black Widow board preparation. Remove 6502 CPU from socket Remove four vector ROM s from their sockets.
6 **note: There is no need to remove the six game ROM s as the Cpu daughter board disables them.** Remove the ER2055 from its socket. Plug CPU daughter board into CPU socket.
7 Plug 6502 processor back into socked on daughter board as shown below. Plug ER2055 daughter board into socket as shown below.
8 Plug vector daughter board into vector ROM sockets as shown below. Plug supplied ribbon cable into the three daughter boards as shown in the picture below. Take note of position of red stripe (pin1) when plugging cable in.
9 Set board aside and open package of hardware as shown below. Remove spacers, lock washers and locking nuts from package. Attach spacers and lock nuts to Space Duel board at the places indicated below.
10 Insert Space Duel pcb into 4in1 main board as shown below.
11 Insert modified Gravitar/Black Widow pcb into main board and attach cable as shown below. Now insert two screws and locking washers into spacers as shown below.
12 THE INSTALL IS NOW COMPLETE!!! On both the Standup & cocktail versions of Space Duel there are plastic card guides/holders that are mounted to the cabinet. Use these to slide the rear board of the stack (which is the Space Duel PWB) back into, you may have to loosen the screws that hold the guides into the cabinet to help with the fit. Take note that all four LED s should be lit.
13 To switch games merely hold down the (P2) button and then use the (P1) to select the next game (Gravitar) and then again to select (Lunar Battle) and again to selecto(black Widow), then the sequence repeats. There are also four jumper headers JP1 = Atari self test JP2 = Cabinet type for Grav/Bwidow PCB ON = Cocktail OFF = Stand Up JP3 Cabinet type for Space Duel PCB ON = Cocktail OFF = Stand Up JP4 = 1&2 Coin mech 1 JP4 = 3&4 Coin mech2 IF YOU HAVE AND PROBLEMS OR SUGGESTIONS ON HOW TO IMPROVE THIS INSTALL GUIDE PLEASE CONTACT VECTOR-LABS@TX.RR.COM THANK YOU FOR YOUR PURCHASE
VS. 4 Game Selector INSTALL GUIDE
VS. 4 Game Selector INSTALL GUIDE Each DK Selector includes the following items: 1. VS. 4 Game Selector PWB 2. 4 power cables 12, 14, 16 & 18 3. Ribbon daisy chain cable 4. Mounting feet and screws Some
More informationDK 4 Game Selector INSTALL GUIDE
DK 4 Game Selector INSTALL GUIDE Each DK Selector includes the following items: 1. DK Selector PWB 2. 4 power cables 12, 14, 16 & 18 3. Ribbon daisy chain cable 4. Mounting feet and screws Some of the
More informationNamco/System1 4in1 Kit INSTALL GUIDE
Namco/System1 4in1 Kit INSTALL GUIDE The Namco/System1 4 in1 kit installed in the picture above. There are 7 PWB s that come with the kit. 1. Voice/Game Controller PWB 2. CHR Rom PWB 3. CHR8 Rom PWB 4.
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationKit K Instructions. V8700 to Alpha Conversion Instructions
V8700 to Alpha Conversion Instructions Contents Contents Installation Instructions for Kit K-00927-0001 Before You Begin..................................................................................
More informationButton Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System
Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept
More informationinto the EMU E4 Classic and E4 Platinum Samplers
Installing the CF-CARD SCSI Card Reader/Writer Drive into the EMU E4 Classic and E4 Platinum Samplers Thank you for purchasing the CF-CARD Internal Card Reader Drive Installation Kit from SCSICardReaders.com.
More informationBasketball Shot Clock Set LX2180 Manual
Basketball Shot Clock Set LX2180 Manual 72 Industrial Boulevard Wrightsville, GA 31096 Phone: (800) 445-7843 Fax: (800) 864-0212 www.electro-mech.com LX2180 Revision 5 February 8, 2013 Table of Contents
More informationI/O Expansion Board. Control Made Simple
? Control Made Simple I/O Expansion Board West Coast Office 1263 El Camino Real Menlo Park, CA 94025 Phone (650) 853-1444? Fax (650) 853-1405 www.flashcutcnc.com Midwest Office 444 Lake Cook Road, Suite
More informationSystem FPGA. wsf - System FPGA. Setup Guide
System FPGA wsf - System FPGA Setup Guide Table of Contents Option Setup Menu...3 System Functions...3 BOOT TO: 3 MACHINE TYPE 3 HOLD 1P+2P TO MENU 4 SCREEN SAVER 4 FAST BOOT 4 49 WAY JOYSTICK 4 BUTTON
More informationG80 MULTIGAME/SPEECH/SOUND INSTALL GUIDE
G80 MULTIGAME/SPEECH/SOUND INSTALL GUIDE The G80 MultiGame kit includes the items pictured above. 1. Main PWA 2. Spinner PWA 3. Wire Harness Interface PWA 4. 48 34 conductor ribbon cable 5. 3 pin connector
More informationForeseesons Monitor Installation Instructions
Foreseesons Monitor Installation Instructions Visit the Merit Entertainment Web site http://www.meritind.com PM0626-04 Table of Contents Parts List... p. 1 Cabinet Identification... p. 1 Cabinets with
More informationTwisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Supplement to Operation & Service Manual
Twisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Supplement to Operation & Service Manual Document Part #: 040-0271-01 Rev. C Your cabinet has a new design with a Sintra Marquee, stand-alone
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the
More informationUltimate LPF kit: Relay-switched LPF kit
Ultimate LPF kit: Relay-switched LPF kit PCB Revision 4 1. Introduction Thank you for purchasing the QRP Labs relay-switched low-pass filter (LPF) kit. This kit is designed to complement the Ultimate3
More informationCarefully remove the translite from the backbox and then lower the speaker panel to the position shown in Fig. A to gain access to the backbox.
Installation Instructions for Data East (wooden speaker panel) Congratulations on the purchase of your new display. The will enhance your pinball machine by introducing color to the dot matrix display
More informationUF-3701 Power Board Construction Guide
Page 1/5 Soldering and Part Placement See the Chapter 3 of the MIT 6270 Manual for information on electronic assembly, including soldering techniques and component mounting. Construction Information All
More informationSystem FPGA. wsf - System FPGA. Setup Guide
System FPGA wsf - System FPGA Setup Guide Table of Contents Option Setup Menu... 3 System Functions... 3 JAMMA to Original Harness Adapter... 6 wsf Board Layout and Connections... 7 JAMMA Button Mappings...
More informationE2460GS Oscilloscope Upgrade Kit
Installation Instructions for E2460GS Oscilloscope Upgrade Kit Agilent 1670G-Series Logic Analyzers This kit upgrades either the Agilent Technologies 1670G, Agilent 1671G, Agilent 1672G, or the Agilent
More informationCarefully remove the translite from the backbox and then swing speaker panel to the open position as shown in Fig. A to gain access to the DMD.
Installation Instructions for SEGA (wooden speaker panel) Congratulations on the purchase of your new display. The will enhance your pinball machine by introducing color to the dot matrix display graphics
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationUzebox JAMMA. Operation manual. (For Uzebox JAMMA Rev. C devices)
Uzebox JAMMA Operation manual (For Uzebox JAMMA Rev. C devices) Basement Hobbies 2011 Contents Warnings 2 Introduction 3 Materials 4 Overview 5 Installation 6 Operation 7 Troubleshooting 13 Contact 16
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationPI36 Raspberry PI Cape/ Standalone Lighting Controller USER MANUAL
PI36 Raspberry PI Cape/ Standalone Lighting Controller USER MANUAL Features -Mates with a Raspberry Pi running the Falcon Player (previously Falcon Pi Player, FPP) -PI is powered by the onboard regulator.
More informationHow to Build a SuperGun or Arcade at Home Machine
How to Build a SuperGun or Arcade at Home Machine Parts Needed: Triple Output Power Supply (+5v,+12v,-5v) 1 Fully wired Jamma Harness RGB to NTSC Video Encoder Panel Mount Video and Audio Jacks Enclosure
More informationIon Memory Upgrade. Visit the AMI Entertainment Web site PM
Ion Memory Upgrade Visit the AMI Entertainment Web site http://www.meritgames.com PM0672-04 COPYRIGHT 2011 AMI ENTERTAINMENT NETWORK, INC. Ion Memory Upgrade CONTENTS: QTY PART NUMBER DESCRIPTION 1 EC0146-06
More informationFC-25/50DA Main Circuit Board Replacement Product Installation Document
FC-25/50DA Main Circuit Board Replacement Product Installation Document Document 51875 Rev A 10/12/01 ECN 01-506 This Product Installation Document outlines the replacement of the Main Circuit Board for
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More information*E * E E0606
75000 SERIES B Instrument BASIC Installation Note Copyright Agilent Technologies, Inc., 1990-2006 *E1300-90020* E1300-90020 E0606 Manual Part Number: E1300-90020 Printed: June 2006 Edition 1 Rev 2 Microfiche
More informationWilliams Games to JAMMA Conversion For Defender, Stargate, Robotron, Joust, Sinistar, Bubbles and Splat!
Williams Games to JAMMA Conversion For Defender, Stargate, Robotron, Joust, Sinistar, Bubbles and Splat! This document was originally downloaded from: WWW.ROBOTRON-2084.CO.UK Disclaimer: Although I have
More informationTROUBLESHOOTING CHAPTER
CHAPTER TROUBLESHOOTING CAUTION: Turn AC power off before attempting any of the following procedures, unless otherwise specified. Failure to do so may damage equipment, cause personal injury, or void warranty.
More informationEMC 10/4 "CE" Mechanical Upgrade Procedure
EMC 10/4 "CE" Mechanical Upgrade Procedure Kit Part Number: 009663-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationUniversal Keying Adapter 3+
Universal Keying Adapter 3+ The Universal Keying Adapter Version 3+ kit will allow you to key nearly any transmitter or transceiver with a straight key, electronic keyer, computer serial or parallel port
More informationQuick Start Guide. SEB-710 I/O Expansion board. Introduction
SEB-710 I/O Expansion board Revision 1.0 - (March, 2011) Saflec Systems (Pty) Ltd Quick Start Guide Introduction The SEB-710 is an I/O expansion device for additional inputs and outputs. It has eight relay
More informationInstalling PRO/DGX or Pro Soloist MIDI interface. R Grieb 9/08/2017
Installing PRO/DGX or Pro Soloist MIDI interface. R Grieb 9/08/2017 Please read these instructions before purchasing the MIDI interface, to make sure you are comfortable performing the necessary steps.
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More information3M I/O Connector Mounting Options and Hardware
M I/O Connector Mounting Options and Hardware Hardware Guide Date Modified: July 20, 2009 Part Number Type Mounting Hardware Applications - Table 1 Mini D Ribbon (MDR) Conn. s D Sub Conn. s D Ribbon Conn.
More informationUSER MANUAL. BBB36+ Beagle Bone Black Cape/ Standalone Lighting Controller
BBB36+ Beagle Bone Black Cape/ Standalone Lighting Controller USER MANUAL Features -Mates with a BeagleBoneBlack (BBB) running the Falcon Player (previously Falcon Pi Player, FPP) -BBB is powered by the
More informationTRAKIT-25P. Printings. Version 1.00: 10/03/01 Version 2.00: 01/20/03 Version 2.10: 01/19/04
TRAKIT-25P Printings Version 1.00: 10/03/01 Version 2.00: 01/20/03 Version 2.10: 01/19/04 TABLE OF CONTENTS SPECIFICATIONS... 1 1.0 GENERAL DESCRIPTION... 2 1.1 Description... 2 1.2 Capabilities and Features...
More informationInstructions to Install Retrofit Kit 6/7000 Machine
Instructions to Install Retrofit Kit 6/7000 Machine **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit kit contents: PART NAME QUANTITY PART NUMBER
More informationMoog Components Group Submux1 Manual December 7, 2009
RS-232 Submux Motherboard (P/N 970381-xxx) and Daughter-cards (4 ch. RS-232 P/N 970391-xxx, 4ch. RS-485 / 2 ch. RS422 P/N 980430-xxx, and Trigger Interface P/N 200700-XXX) User s Manual And Troubleshooting
More informationEP-ELVCTL Elevator Control (NION-16C48M)
EP-ELVCTL Elevator Control (NION-16C48M) Product Installation Document This document covers the procedures and specifications for installing the above listed unit and when appropriate, information regarding
More informationEB-51 Low-Cost Emulator
EB-51 Low-Cost Emulator Development Tool for 80C51 Microcontrollers FEATURES Emulates 80C51 Microcontrollers and Derivatives Real-Time Operation up to 40 MHz 3.3V or 5V Voltage Operation Source-Level Debugger
More informationConstruction manual. (Almost Ready To Control) Stand , V1.05
V.3 ARTC Construction manual V.3 ARTC (Almost Ready To Control) Stand 5.08.206, V.05 Qube Solutions UG (limited liability) Arbachtalstr. 6, 72800 Eningen, GERMANY http://www.qube-solutions.de/ http://
More informationStar Trac Fitness E-ST 5090 Stepper. Install Guide
Star Trac Fitness E-ST 5090 Stepper Install Guide STAR TRAC E-ST STEPPER Install Guide E-ST 5090 E Series Stepper ASSEMBLY AND SETUP The following parts are included with the base STAR TRAC E-ST STEPPER:
More informationA TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address
Requirements A TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address Power Up A Reader with an Ethernet adaptor installed and the network cable
More informationReplacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly
Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Assembly Introduction The Replacement Kit provides a replacement backlight for the PanelMate Power Pro 1785 Series,
More informationInstallation Instructions
Installation Instructions This document provides information on: important pre-installation considerations power supply requirements initial handling installing the module short circuit protection using
More informationFrightfearland Conversion Kit Instructions
Frightfearland Conversion Kit Instructions for Aliens Extermination and Paradise Lost Cabinets Document Part #: 040-0248-01 This kit converts an Aliens Extermination or Paradise Lost Upright Cabinet to
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationDOEPFER. Midi Bass Pedal Electronic Kit MBP25. User's Guide
DOEPFER Midi Bass Pedal Electronic Kit MBP25 User's Guide 2008 by Doepfer Musikelektronik GmbH Geigerstr. 13 82166 Graefelfing Deutschland / Germany Phone: + 49 89 89809510 Fax: + 49 89 89809511 Web Site:
More information8088 All-in-One Gameboard Setup Guide For v1.02 / 1.02 Rev.A / v1.03 board hardware
mylfpga 8088 All-in-One Gameboard Setup Guide For v1.02 / 1.02 Rev.A / v1.03 board hardware Table of Contents Board Layout... 3 Hardware & Connectors... 4 Connectors 4 Voltage & Current 4 JAMMA wiring...
More informationEMC 10T "CE" Mechanical Upgrade Procedure
EMC 10T "CE" Mechanical Upgrade Procedure Kit Part Number: 009866-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationUniversity of Florida EEL 4744 Drs. Eric M. Schwartz, Karl Gugel & Tao Li Department of Electrical and Computer Engineering
Page 1/9 Revision 1 OBJECTIVES In this document you will learn how to solder and to debug a board as you are building it. REQUIRED MATERIALS Website documents o UF 68HC12 Development Board Manual (board
More informationDMX512-4 Channel PWM Driver Board #805
DMX512-4 Channel PWM Driver Board #805 Overview The 4-channel PWM driver board provides four open drain (collector) type outputs that can be directly controlled from a DMX512 network. The four channels
More informationVG-305A AC Traffic Light Controller Kit
Galak Electronics Electronic kits and components Website: GalakElectronics.com Email: sales@galakelectronics.com Phone: (302) 832-1978 VG-305A AC Traffic Light Controller Kit Thank you for your purchase
More informationChapter 3 Installation
Installation Chapter 3 Installation This chapter will guide you through the installation of your I/ O Extension A.3 board. It includes instructions on how to set the I/O port address and interrupt request
More informationN8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B.
N8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B. Background. This board is a copy of Andrew Lynch s Version 03 board (with 8 slots) but with added features. Added features: 9 SLOT Active Termination (copied
More informationWORDSYNC ADDENDUM to the SupraDrive Operator s Manual
WORDSYNC ADDENDUM to the SupraDrive Operator s Manual Congratulations on your purchase of a SupraDrive Hard Card or WordSync Interface Kit for your Amiga 2000 computer. Your new hard drive system will
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationComputer Maintenance. PC Disassembly and Reassembly. Copyright Texas Education Agency, All rights reserved.
Computer Maintenance PC Disassembly and Reassembly 1 Enabling Objectives Computer Chassis (Cases) Power Supplies Configuring the Motherboard Configuring the Connectors CPU Interfaces RAM Installing a Hard
More informationDMX36 USER MANUAL Features Revision 1 Suits PCB revision June, 2014
DMX36 USER MANUAL Features -The DMX36 controller accepts DMX data input and drives 36 DC channels. -Quad DC input (5V, 7-35V) (large screw terminals) -4x 30A mini blade fuses (30A overall max per 9 channels)
More informationInk-Dot Series II Driver
Instruction Sheet P/N 766B Ink-Dot Series II Driver Introduction See Figure. Ink-Dot Series II controllers can have from one to three driver modules. Any existing controller can easily be retrofit with
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationAltair 8800b Restoration
Altair 8800b Restoration I purchased this Altair 8800b through ebay. This is a very heavy computer, especially in the corner with the enormous transformer. Unfortunately, the seller shipped the computer
More informationUpgrading a 2U CHP to an i7 Quad Core SBC
Upgrading a 2U CHP to an i7 Quad Core SBC 1. Parts required: i7 SBC Slim line SATA DVD drive Combined SATA data and power cable for slim-line optical drive Serial port ribbon cable - 9way D male to 10
More informationFigure 1. 6-Way JAMMA Switcher
RiddledTV.com 6-Way, Single-Board JAMMA Switcher INSTALLATION GUIDE Figure 1. 6-Way JAMMA Switcher Features: Supports 6 JAMMA boards Only 1 JAMMA board is powered at a time. No external remotes required
More informationNumber Name Description Notes Image 0101 Resistor, 100 ohm. brown-black-browngold. ¼ watt, 5% tolerance, red-red-brown-gold. brown-black-red-gold.
Passive Components 0101 Resistor, 100 brown-black-browngold. 690620 0102 Resistor, 220 red-red-brown-gold. 690700 0103 Resistor, 1000 brown-black-red-gold. 690865 0104 Resistor, 10k 0201 Capacitor, 1 µf,
More informationSingle ROM Prototyping Board (SRBP) Instructions Version 2.0
Single ROM Prototyping Board (SRBP) Instructions Version 2.0 Copyright 2015 Brian E. Brzezicki http://www.arcade-cabinets.com Disclaimer The Single ROM Prototyping Board (SRBP) is provided as is without
More informationVoice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document
Voice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document Document 50795 Rev B 10/10/01 ECN 01-507 This Product Installation Document outlines the replacement of the Main
More informationEPROM Replacement for Contrbl Systems
EPROM Replacement 1 EPROM Replacement for OmniScan@ Contrbl Systems Important 0 Before starting, read all instruction sheets that have been provided with your service kit It is recommended that you use
More informationOracle <Insert Picture Here>
Slide 1 Oracle Slide 2 WZT-6509 version B Sun Fire Nehalem and Westmere Rack-Mount Server Installation and Replacement Welcome to the installation and replacement
More informationAssembly Manual for Mobile X-ray
Suitable for Kodak 2000, Kodak 2100, Kodak 2200 and Trophy Elytis - 12 th January 2011 William Green Page 1 of 8 Printed 12/01/2011, 2:07:42 PM Mobile X-ray Parts List 1. 6 x M10 x 65mm UNB CAP Bolts 2.
More informationAssignment 5. You can configure hardware options by setting jumper on the mainboard. See Figure 2-1 for jumper locations. Set a jumper as follows:
CIS 170 Microcomputer Hardware Name: Assignment 5 From the lack of having enough peripherals for this course (at least at this point), we have the necessity of doing some experiments mentally rather than
More informationInstalling TEAC CD-ROM Drives
D I G I T A L Installing TEAC CD-ROM Drives S O U N D Date: May 12, 2000 (updated) Document # TN-E211 We have used only two manufacturers of CD-ROM drives: Toshiba and TEAC. This procedure is to be used
More informationTechnovision Inc. CD-ROM Audio Sampler. Repair Manual
Technovision Inc. CD-ROM Audio Sampler Repair Manual Table Of Contents: Page # INITIAL SETUP & TESTING 3 System Components 3 System Set-Up Procedure 3 Self Test Routine 3 REPAIR ACTION PARTS REPLACEMENT
More informationUSER MANUAL DMX36. Features
DMX36 USER MANUAL Features -The DMX36 controller accepts DMX data input and drives 36 DC channels. -Quad DC input (5V, 7-35V) (large screw terminals) -4x 30A mini blade fuses (30A overall max per 9 channels)
More informationHow to install shaker motor in a LOTR standard edition
How to install shaker motor in a LOTR standard edition What you need: 1. Shaker motor kit Stern Rev. B [www.free-play.se; FP-502-5027-00-01] 2. LOTR v10.02 game ROM chip [www.free-play.se; FP-GROM-LOTR
More informationModel ver INSTALLATION MANUAL Rev CHD Elektroservis
Model 8-435 ver. 1.0 INSTALLATION MANUAL Rev. 2 7 2018 CHD Elektroservis Contents page 1 INTRODUCTION.................................................................. 3 1.1 MIDI INTERFACE KIT PARTS.......................................................
More information6 Channel RS-422 Board (P/N xxx) User s Manual. And. Troubleshooting Guide
6 Channel RS-422 Board (P/N 200560-xxx) User s Manual And Troubleshooting Guide February 24, 2009 Rev. B Moog Components Group Springfield Operations 750 West Sproul Road Springfield, PA 19064 E-Mail:
More informationProduct Specification. Shuttle XPC Accessory. COM / LPT / RJ11 port expansion for Shuttle XPC aio X50V4/V5/V6. Feature Highlight
COM / LPT / RJ11 port expansion for Shuttle XPC aio X50V4/V5/V6 The Shuttle accessory POS01 is compatible with the Shuttle XPC All-in-One- X50V4, X50V5 und X50V6. It will add four serial (COM), one parallel
More informationModel LX8850 Product Guide
Model LX8850 Product Guide Indoor Hockey Scoreboard 72 Industrial Boulevard Wrightsville, GA 31021 Phone:(800) 445-7843 Fax:(800) 864-2012 www.electro-mech.com LX8850 Revision 7 February 27, 2013 Table
More information1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist.
CONSOLE CONNECTOR KIT 8101 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models A-100, D-100, RT2, RT3 LESLIE Speaker Models 122, 122RV KIT CONTENT Console Connector Assembly 047357 Echo Control
More informationSRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
More informationData sheet GCM MOD GMM EC.1 Communications module Modbus for GMM EC
Data sheet GCM MOD GMM EC.1 Communications module Modbus for GMM EC ERP no.: 5206415 GCM MOD GMM EC.1 www.guentner.de Page 2 / 15 Contents 1 GCM MOD GMM EC.1...3 1.1 Functional description...3 1.2 Connections...
More informationARM programmer and daughter board
ARM programmer and daughter board www.matrixtsl.com EB185 Contents About this document 3 Board layout 3 General information 4 Circuit description 4 Protective cover 5 Circuit diagram 6 2 Copyright About
More informationYou need the following components to assemble the Black n Wood Nixie Clock circuit board:
You need the following components to assemble the Black n Wood Nixie Clock circuit board: Quantity Designator Description 1 Battery Battery, CR1220 1 Battery Battery holder 3 Button 1, Button 2, Button
More informationTroubleshooting CHAPTER
CHAPTER 1 1 1 1 0 1 1 0 1 1 0 1 1 0 1 1 0 1 1 0 1 1 0 1 1 1 0 1 6 0 1 1 0 1 1 0 1 0 1 10 1 0 1 1 0 1 0 1 1 0 1 0 1 1 0 1 10 Troubleshooting NOTICE: Information in this manual may change without notice.
More information4100/ VDC Converter Installation Instructions
4100/4120-0156 8 VDC Converter Installation Instructions Introduction This publication describes the installation procedure for the 8 VDC Converter. Related Documentation Field Wiring Diagram for 4100
More informationSierra Radio Systems. Digital Compass. Reference Manual. Version 1.0
Sierra Radio Systems Digital Compass Reference Manual Version 1.0 Contents Digital compass board RS485 power injector For more information, go to the Sierra Radio Systems web site at www.sierraradio.net
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationPS/2 Keyboard Interface User s Manual
PS/2 Keyboard Interface User s Manual Cloud-9 Cloud-9 3749 County Road 30 Delano, MN 55328 1 www.cloud9tech.com PS/2 Keyboard Interface 2013 Cloud-9 All Rights Reserved All portions of this hardware are
More informationSM010, Assembly Manual PCB Version 1.0
180 SM010, Assembly Manual MATRIXARCHATE 16 8 IO SEQUENTIAL MATRIX SIGNAL ROUTER SM010 1 2 1 2 3 4 5 3 4 5 6 7 8 9 10 11 12 6 7 8 9 10 11 12 13 14 15 16 PROGRAM A B C D E F G H f1 f2 20.000 180 SSSR Labs
More informationQuicksilver 606 TR-606 CPU Upgrade
Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...
More informationTIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE
TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE Table of Contents 0. Components List + Tools 0. PCB Sides 03. PCB Assembly 04_. Diode N448 04_. Laying Resistors 04_3. Capacitors 04_4. Quartz 04_5. 78L05
More informationCHAPTER Wi r i n g NOTICE:
CHAPTER Wiring NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering
More informationINSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,
More informationDSP-232 Upgrade Kit A.06113
DSP-232 Upgrade Kit A.063 Installation and Operation Manual Rev. 2.0 WARRANTY WHO IS COVERED WHAT WE WILL DO WHAT YOU MUST DO WHAT IS NOT COVERED SERVICE WARRANTY HOW TO CONTACT TIMEWAVE TIMEWAVE TECHNOLOGY
More information