Compact Block LDX I/O for DeviceNet

Transcription

1 Compact Block LDX I/O for DeviceNet Technical Data 1790D, 1790 The CompactBlock TM I/O product family now offers you a new, more cost-effective I/O product line for light industrial and commercial automation environments. CompactBlock LDX I/O utilizes the leading, lowest-cost, device-level communication network, DeviceNet TM, to translate simple messages from the controller to the plant floor. It is especially suitable where low cost and confined space is coupled with reduced envrionmental requirements.

2 2 Overview CompactBlock LDX I/O The following CompactBlock LDX I/O for DeviceNet base and expansion blocks are available with either D-shell connectors or screw terminations (terminal blocks): D-hell Blocks 1790D-16BV0 1790D-8BV8B 1790D-8BV8V 1790D-0B D-0V D-0W BV0X BV8BX BV8VX B16X V16X W8X 1790D-N4C0 1790D-N0C2 1790D-N4V0 1790D-N0V2 1790D-4R0 1790D-4T0 Terminal Blocks 1790D-T16BV0 1790D-T8BV8B 1790D-T8BV8V 1790D-T0B D-T0V D-T0W6 1790D-T8A0 1790D-T0A T16BV0X 1790-T8BV8BX 1790-T8BV8VX 1790-T0B16X 1790-T0V16X 1790-T0W8X 1790-T8A0X 1790-T0A8X 1790D-TN4C0 1790D-TN0C2 1790D-TN4V0 1790D-TN0V2 1790D-T4R0 1790D-T4T0 Description 24VDC, 16 universal input base block 24VDC, 8 universal input/8 sourcing output base block 24VDC, 8 universal input/8 sinking output base block 24VDC, 16 sourcing output base block 24VDC, 16 sinking output base block 6 relay output base block 24VDC, 16 universal input expansion block 24VDC, 8 universal input/8 sourcing output expansion block 24VDC, 8 universal input/8 sinking output expansion block 24VDC, 16 sourcing output expansion block 24VDC, 16 sinking output expansion block 8 relay output expansion block 4 channel analog current input block 2 channel analog current output block 4 channel analog voltage input block 2 channel analog voltage output block 4 channel input RTD base block 4 channel input Thermocouple base block Description 24VDC, 16 universal input base block 24VDC, 8 universal input/8 sourcing output base block 24VDC, 8 universal input/8 sinking output base block 24VDC, 16 sourcing output base block 24VDC, 16 sinking output base block 6 relay output base block 120VAC, 8 input base block 120VAC, 6 output base block 24VDC, 16 universal input expansion block 24VDC, 8 universal input/8 sourcing output expansion block 24VDC, 8 universal input/8 sinking output expansion block 24VDC, 16 sourcing output expansion block 24VDC,16 sinking output expansion block 8 relay output expansion block 120VAC, 8 input expansion block 120VAC, 8 output expansion block 4 channel analog current input block 2 channel analog current output block 4 channel analog voltage input block 2 channel analog voltage output block 4 channel input RTD base block 4 channel input Thermocouple base block Publication 1790D-TD001B-EP - February 2002

3 CompactBlock LDX I/O Overview 3 Overview CompactBlock LDX I/O Blocks CompactBlock LDX I/O for DeviceNet blocks are compatible with PLC, LC, oftlogix or Logix programmable controllers using DeviceNet scanners. All CompactBlock LDX I/O block values are accessible through the data tables of the PLC or LC programmable controller. et node addresses on the blocks using rotary switches, located on the base block, RNetWorx for DeviceNet software or a similar configuration tool. et baud rate using a similar configuration tool. Benefits Base block with D-shell connector Expansion block with D-shell connector Base block with screw terminations Expansion block with screw terminations Wide breadth of I/O types that can handle diverse commercial applications Expands up to 4 digital blocks for flexibility of node size (6-64 points) Base blocks have a built-in DeviceNet adapter Digital base blocks (24Vdc, 120Vac and relay) can support up to 3 digital expansion blocks base blocks (current and voltage) can support up to 2 digital expansion blocks RTD and Thermocouple base blocks do not support expansion blocks Universal sink/source inputs reduces the number of components to stock and allows flexibility of input types Compatible with a broad range of sensors: NEMA/IEC Type 3 compliance for DC blocks NEMA/IEC Type 1 compliance for AC blocks Very compact, can fit into confined areas (104mm x 52mm x 42mm) electable termination types - removable D-shell and fixed screw termination Easy to connect and configure using modular ED files Installation and configuration costs are minimized ODVA conformance tested means high level of interoperability with other DeviceNet products RTD and thermocouple blocks support a wide range of sensors and have on-board scaling Cyclic and change-of-state messaging increases network throughput, increases productivity Auto baud rate detection Mounts horizontally or vertically on DIN rail UL/cUL Listed, CE certified Publication 1790D-TD001B-EP - February 2002

4 PULL EXPANION UNIT CompactBlock LDX PULL PULL EXPANION UNIT CompactBlock LDX PULL PULL EXPANION UNIT CompactBlock LDX PULL PULL 4 Overview CompactBlock LDX I/O Typical Configuration This illustration shows how CompactBlock LDX I/O fits into a typical DeviceNet system PCD PCMCIA card Personal Computer with Configuration software PLC-5 controller 1771-DN scanner 1747-DN scanner LC controller eries 9000 Photoelectric ensors RediTATION Interface DTAM TM Micro or plus 1305 Drive 1336 PLU TM Drive GV3000 drive 1336 FORCE Drive FlexPac 3000 drive Ezlink TM bearing monitor C TM Bulletin 160 FLEX I/OTM ArmorBlock TM I/O DeviceView TM hand-held computer MC TM motor starter with MP-3 TM Dialog Plus 1790 CompactBlock LDX I/O overload relay DeviceLink TM I/O with limit switch M ystem Compatibility CompactBlock LDX I/O blocks are compatible with PLC, LC or oftlogix programmable controllers when used with DeviceNet scanners. CompactBlock LDX I/O Family Block Communication The CompactBlock LDX I/O blocks act as slaves in a master/slave environment. Their I/O data is exchanged with the master through a polled, cyclic, or change-of-state connection. This selection is made in the DeviceNet scanner module s configuration. Polled When configured as a polled device, a master initiates communication by sending its polled I/O message to the CompactBlock LDX I/O block. In response, the I/O block returns its input data. Cyclic When using cyclic operation, the master only sends data to the CompactBlock LDX I/O block and only receives data from the block at a preconfigured time interval. Publication 1790D-TD001B-EP - February 2002

5 CompactBlock LDX I/O Overview 5 Change-of-tate When the CompactBlock LDX I/O blocks are configured for change-of-state, the master sends output data only when: the user s control program wants to update the block s output the time period for communication has expired The CompactBlock LDX I/O block s input data is sent to the master only when: an input changes the time period for communication has expired With change-of-state, the master does not have to request input data from the slave, it is sent automatically when data changes. In addition, an adjustable "heartbeat" is produced periodically by the CompactBlock LDX I/O block to let the consuming device know that the block connection is alive and ready to communicate. oftware and ED File Requirements CompactBlock LDX I/O block require RNetWorx for DeviceNet software, version 3.0 or later. Additionally, current functionality of CompactBlock LDX I/O blocks require current modular ED files for RNetWorx for DeviceNet software. These files are easy to install and are available on-line at: ED files for blocks with matching catalog numbers (for D-hell and terminal block versions) are the same. Thus on the website or in RNetWorx for DeviceNet, there may be only one catalog number listed for both versions. tatus Each CompactBlock I/O block has indicators to provide a diagnostic readout. Module and Network tatus Base Block I/O tatus I/O tatus Expansion Block Publication 1790D-TD001B-EP - February 2002

6 6 Overview CompactBlock LDX I/O Module/Network tatus - All Base Blocks Mod/Net tatus Indicator LED Indicator: tatus: Description: Module tatus olid Red Unrecoverable fault in base block Flashing Red Recoverable fault olid Green Normal operation - OK Flashing Green tandby Off No power LED Indicator: tatus: Description: Network tatus olid Red Unrecoverable communication fault Flashing Red Recoverable communication fault olid Green Communication path complete - OK Flashing Green Communication path incomplete Off Device not online or not powered I/O tatus - Digital Base and Expansion Blocks I/O tatus Function: LED Color: Module Illumination: Condition: s Each output: Green None Green not energized energized s Each : Green None Green No valid input Valid input I/O tatus - Base Blocks 1790D-N4V0, -TN4V0 Voltage Block 1790D-N4C0, -TN4C0 Current Block tatus: Description: tatus: Description: Flashing Green/ Red up Flashing Green/ Red up Off Off line Off Off line Red On line and no field Red On line and no field power power Red Green Green DeviceNet connection and no field power Field power and open wire Field power and valid input Red Flashing Red 1 Green DeviceNet connection and no field power Field power and open wire (4-20mA range only) 2 Field power and valid input Green over range Green over range Green under range Flashing Red 1 under range <3mA (4-20ma range only) 2 Flashing Red Recoverable fault Flashing Red Recoverable fault 1 Green for 0-20mA range. 2 Can be determined from the data table. Publication 1790D-TD001B-EP - February 2002

7 CompactBlock LDX I/O Overview 7 I/O tatus - Base Blocks 1790D-N0V2, -TN0V2 Voltage Block 1790D-N0C2, -TN0C2 Current Block tatus: Description: tatus: Description: Flashing Green/ Red up Flashing Green/ Red up Off Off line Off Off line Off On line and no field Off On line and no field power power Green Green Green Flashing Red DeviceNet connection and no field power Field power and open wire Field power and valid output Field power and output out of range Green Green Green Flashing Red DeviceNet connection and no field power Field power and open wire Field power and valid output Field power and output out of range Flashing Green idle Flashing Green idle Flashing Red Recoverable fault Flashing Red Recoverable fault I/O tatus - RTD and Thermocouple Base Blocks 1790D-4R0, -4T0 tatus: Flashing Green/Red Off Red Red Flashing Red Green Flashing Red Flashing Red Flashing Red Description: up Off line On line and no field power DeviceNet connection and no field power Field power and open wire Field power and valid input over range under range Recoverable fault upply Requirements The DeviceNet network supplies power to the CompactBlock I/O base and expansion blocks. s and outputs are powered by an external 24V dc source which is independent of the network. Mounting You can mount the CompactBlock I/O base and expansion blocks directly to a panel or on a DIN rail. Publication 1790D-TD001B-EP - February 2002

8 PULL PULL PULL PULL PULL PULL PULL PULL PULL PULL PULL PULL 8 Overview CompactBlock LDX I/O The following illustration shows the base and expansion blocks mounting dimensions. Base block 95 mm 3.74 in 25mm 1 in 95 mm 3.74 in Expansion block 41mm 1.6 in 41mm 1.6 in Remember to consider the length of the expansion ribbon cable when installing a base block with an expansion. The expansion block must be close enough for the expansion cable to reach from the base block to the expansion block. To install plug, gently pull and swing expansion cover inward Red strip must be on bottom of expansion cable Beginning with the base block, you can mount the blocks either horizontally or vertically as shown below: EXPANION UNIT CompactBlock LDX EXPANION UNIT CompactBlock LDX EXPANION UNIT CompactBlock LDX EXPANION UNIT CompactBlock LDX RIGHT IDE UP RIGHT IDE UP RIGHT IDE UP RIGHT IDE UP EXPANION UNIT CompactBlock LDX RIGHT IDE UP UPIDE DOWN The longer expansion cable ( CMCBL) will allow up to 7cm of space between blocks EXPANION UNIT CompactBlock LDX PULL PULL EXPANION UNIT CompactBlock LDX RIGHT IDE UP Publication 1790D-TD001B-EP - February 2002

9 CompactBlock LDX I/O Overview 9 CompactBlock LDX I/O Accessories and DeviceNet Cables CompactBlock LDX I/O Accessories Description 5-position open style plug for DeviceNet 5-position open style plug for DeviceNet (with locking screws) 5-position plug adapter to 12mm male connector, straight 7cm LDX I/O replacement ribbon cable (included with expansion module) 15cm optional LDX I/O ribbon cable (required for vertical mounting) DeviceNet Cables Part Number 1799-DNETCON 1799-DNETCON 1799-D5MM CMCBL CMCBL Description Mini male to conductor (unshielded) Mini male to conductor (shielded) Length m Part Number (aluminum): Part Number (stainless steel): Application: P1M5-C 1485R-P1M5-C DeviceNet drop cable R-P6M5-C 1485R-P6M5-C (flat media) R-P1M5-C 1485P-1M5-C DeviceNet drop cable R-P2M5-C 1485R-P2M5-C (round media) R-P3M5-C 1485R-P3M5-C Detailed Block Information The remainder of this publication describes detailed informaton for each CompactBlock LDX I/O block, such as: schematic diagrams connection sizes word/bit definitions connection wiring diagrams specifications Publication 1790D-TD001B-EP - February 2002

10 10 Overview CompactBlock LDX I/O Refer to the table below to find information about a specific block. For information about: ee page: DeviceNet Digital and Base and Expansion D-hell Blocks 11 24VDC, 16 universal input (1790D-16BV0 and BV0X) 12 24VDC, 8 universal input/8 sinking output1790d-8bv8v and BV8VX) 13 24VDC, 8 universal input/8 sourcing output (1790D-8BV8B and BV8BX) 14 24VDC, 16 sourcing output (1790D-0B16 and B16X) 14 24VDC, 16 sinking output (1790D-0V16 and V16X) 16 6 relay output (1790D-0W6) and 8 relay output (1790-0W8X) 17, 18 4 channel analog current input (1790D-N4C0) 19 4 channel analog voltage input (1790D-N4V0) 20 2 channel analog current output (1790D-N0C2) 21 2 channel analog voltage output (1790D-N0V2) 22 4 channel input RTD base block (1790D-4R0) 23 4 channel input Thermocouple base block (1790D-4T0) 24 DeviceNet Digital and Base and Expansion Terminal Blocks 25 24VDC, 16 universal input (1790D-T16BV0 and 1790-T16BV0X) 26 24VDC, 8 universal input/8 sinking output (1790D-T8BV8V and 1790-T8BV8VX) 27 24VDC, 8 universal input/8 sourcing output (1790D-T8BV8B and 1790-T8BV8BX) 28 24VDC, 16 sourcing output (1790D-T0B16 and 1790-T0B16X) 29 24VDC, 16 sinking output (1790D-T0V16 and 1790-T0V16X) 30 6 relay output (1790D-T0W6 and1790-t0w8x) 31, VAC, 8 input (1790D-T8A0 and 1790-T8A0X) VAC, 6 output (1790D-T0A6) and 8 output (1790-T0A8X) 34, 35 4 channel analog current input (1790D-TN4C0) 36 4 channel analog voltage input (1790D-TN4V0) 37 2 channel analog current output (1790D-TN0C2) 38 2 channel analog voltage output (1790D-TN0V2) 39 4 channel input RTD base block (1790D-T4R0) 40 4 channel input Thermocouple base block (1790D-T4T0) 41 Related Publications Refer to the following list of publications for more information about CompactBlock LDX I/O blocks as well as the DeviceNet network and its products. Title: Publication Number: CompactBlock LDX I/O Product Profile 1790-PP002B-EN-P DeviceNet Base Terminal Block CompactBlock LDX I/O Installation Instructions 1790-IN002A-EN-P Digital Expansion D-shell Block CompactBlock LDX I/O Installation Instructions 1790-IN003A-EN-P DeviceNet Base D-shell CompactBlock LDX I/O Installation Instructions 1790-IN004A-EN-P Digital Expansion Terminal Block CompactBlock LDX /O Installation Instructions 1790-IN005A-EN-P DeviceNet Digital Base Terminal Block CompactBlock LDX I/O Installation Instructions 1790-IN006A-EN-P DeviceNet Digital Base D-shell Block CompactBlock LDX I/O Installation Instructions 1790-IN007A-EN-P DeviceNet Digital Base RTD and Thermocouple D-shell and Terminal Block 1790-IN011A-EN-P CompactBlock LDX I/O Installation Instructions DeviceNet election Guide DNET-G001A-EN-P DeviceNet Product Overview DN-2.5 DeviceNet Cable ystem Planning and Installation Manual DN Publication 1790D-TD001B-EP - February 2002

11 CompactBlock LDX I/O DeviceNet Digital and D-hell Blocks 11 DeviceNet Digital and D-hell Blocks The DeviceNet digital and analog D-shell block I/O is exchanged with the master through a poll, change-of-state, or cyclic connection. Polled - a master initiates communication by sending its polled I/O message to the block. The block consumes the message, updates any outputs, and produces a response. If any inputs are present, the response will contain the input data. Change-of-state - productions occur when an input changes. If no input change occurs within the expected packet rate, a heartbeat production occurs. This heartbeat production tells the scanner module that the block is alive and ready to communicate. Consumption occurs when data changes and the master produces new output data to the block. Cyclic - allows configuration of the block as an I/O client. The block will produce and consume its I/O cyclically at the rate configured. The DeviceNet Network uses advanced network technology, producer/consumer communication, to increase network functionality and throughput. Visit our Web site at for producer/ consumer technology information and updates. General pecifications The following table contains specifications that are common to all of the DeviceNet base and expansion blocks in this section. Individual block connection sizes, word/bit definitions, schematics, wiring diagrams and specifications are detailed after this table. Environmental pecifications Operating Temperature 0 to 55 C (32 to 131 F) IEC (Test Ad, Operating Cold), IEC (Test Bd, Operating Dry Heat), IEC (Test Nb, Operating Thermal hock) torage Temperature -40 to 85 C (-40 to 185 F) IEC (Test Ab, Un-packaged Non-operating Cold), IEC (Test Bb, Un-packaged Non-operating Dry Heat), IEC (Test Na, Un-packaged Non-operating Thermal hock) Relative Humidity 5-90% non-condensing IEC (Test Db, Un-packaged Non-operating) Operating Altitude 2000m Vibration Hz EC (Test Fc, Operating) Environmental pecifications hock: Operating I0g Non-operating 30g IEC Test Ea, (Unpackaged hock) Emissions Group 1, Class A CIPR 11 ED Immunity 8kV air discharges IEC Radiated RF Immunity 10V/m with 1kHz sine-wave 80%AM from 80MHz to 1000MHz 10V/m with 200Hz 50% Pulse 900Mhz IEC EFT/B Immunity 5kHz on power ports 5kHz on signal ports 5kHz on communications ports IEC urge Transient Immunity Conducted RF Immunity +1kV line-line(dm) and +2kV line-earth(cm) on power ports +1kV line-line(dm) and +2kV line-earth(cm) on signal ports +2kV line-earth(cm) on shielded ports IEC Vrms with 1kHz sine-wave 80%AM from 150kHzto 80MHz IEC Enclosure Type Rating None (open style) Mounting DIN rail or screw Dimensions 52x104x42mm (2.03x4.07x1.64in) Weight 0.3lb (0.1kg) 1 Refer to publication , Programmable Controller Wiring and Grounding Guidelines. DeviceNet pecifications Network protocol I/O lave messaging: - Poll command - Bit trobe command - Cyclic command - CO command Network length 500 meters 125Kbps 100 meters 500Kbps 1 red/green module status 1 red/green network status Number of nodes 64 maximum - rotary switch type node address setting Communication rate 125Kbps, 250Kbps, 500Kbps - auto baud rate selection Type test 1250Vac rms for 60 seconds between field power and DeviceNet (I/O to logic) Wiring Refer to publication DN General pecifications Wiring Category 2 1 Product Certifications (when product or packaging is marked) c-ul-us CE 2 C-Tick 2 ODVA UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.. and Canada European Union 89/336/EEC EMC Directive, compliant with: EN ; Industrial Emissions EN ; Industrial Immunity EN61326; Meas./Control/Lab., Industrial Requirements EN ; Industrial Immunity Australian Radiocommunications Act, compliant with: A/NZ 2064; Industrial Emissions ODVA conformance tested to ODVA DeviceNet specifications 1 Refer to publication , Programmable Controller Wiring and Grounding Guidelines. 2 ee the Product Certification link at for Declarations of Conformity, Certificates, and other certification details.

12 12 DeviceNet Digital and D-hell Blocks CompactBlock LDX I/O 24VDC 16 Universal Base and Expansion Block D-16BV0 and BV0X implified chematic Wiring Diagram for D-hell Connector COM0 I0 I1 I2 I3 I4 I5 I6 I7 I8 COM2 I10 I12 I14 I9 I11 I13 I COM1 COM1 COM1 COM1 COM1 COM3 COM3 COM3 COM3 COM1 COM1 COM1 COM1 COM3 COM3 COM3 COM3 COM3 +/- 24Vdc -/+ COM Opto ystem Circuitry Indication LED (logic) For inputs 0-7: inking inputs - wire Com 1 to Field (+) 24V dc, wire Com 0 to Field (-) ourcing inputs - wire Com 1 to Field (-), wire Com 0 to Field (+) 24V dc For inputs 8-15: inking inputs - wire Com 3 to Field (+) 24V dc, wire Com 2 to Field (-) ourcing inputs - wire Com 3 to Field (-), wire Com 2 to Field (+) 24V dc Note: All Com 1 and Com 3 are internally connected - Com 1 is used for inputs 0-7, Com 3 is used for inputs Block pecifications 1790D-16BVO and 1790-BV0X Connection izes Blocks 1790D-16BV0, BV0X I/O Points Produce 16 input 2 0 Bit Produces 0 I7 I6 I5 I4 I3 I2 I1 I0 Produces 1 I15 I14 I13 I12 I11 I10 I9 I8 Word Bit Description Produces tatus bits - when the bit is set (1), the input is on. Bit 00 corresponds to input I0, bit 01 corresponds to input I1, bit 02 corresponds to input I2, bit 03 corresponds to input I3, etc. Produces tatus bits - when the bit is set (1), the input is on. Bit 00 corresponds to input I8, bit 01 corresponds to input I9, bit 02 corresponds to input I10, bit 03 corresponds to input I11, etc. s per block On-state voltage Off-state voltage On-state current Nominal input impedance Common type General pecifications 16 points, sinking or sourcing 9.6V dc minimum 24V dc nominal 28.8V dc maximum 5.0V dc maximum 8mA maximum per 28.8V dc 4.8KΩ 16 green input status 8 points/8com (non-polarity) DeviceNet - base block upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc voltage: 1250V ac rms DeviceNet to logic: non-isolated DeviceNet power: non-isolated Wiring 37-pin D-hell connector

13 CompactBlock LDX I/O DeviceNet Digital and D-hell Blocks 13 24VDC 8 Universal /8 inking Base and Expansion Blocks D-8BV8V and BV8VX Wiring Diagram for D-hell Connector COM0 I0 I1 I2 I3 I4 I5 I6 I7 O0 O2 COM2 O1 O3 O4 O6 O5 O implified chematic 24Vdc +/- Opto ystem Circuitry Indication LED (logic) COM1 COM1 COM1 COM1 COM1 COM2 COM2 COM2 COM2 COM1 COM1 COM1 COM1 COM3 COM2 COM2 COM2 COM2 inking inputs - wire Com 1 to Field (+) 24V dc, wire Com 0 to Field (-) ourcing inputs - wire Com1 to Field (-), wire Com 0 to Field (+) 24V dc Note: all Com 1 are internally connected. inking outputs -wire Com 2 to Field (+) 24Vdc, wire Com 3 to Field (-) Note: all Com 2 are internally connected. -/+ COM Block pecifications Indication LED (logic) Vdc 1790D-8BV8V and BV8VX INPUT PECIFICATION ystem Circuitry Opto Protected Device 24Vdc s per block On-state voltage 8 points non-isolated, sinking or sourcing 9.6V dc minimum 24V dc nominal 28.8V dc maximum On-state current Off-state voltage 8mA maximum per 28.8V dc 5V dc maximum Connection izes Nominal input impedance 4.8KΩ 8 green status Blocks I/O Points Produce Common type OUTPUT PECIFICATION 8 points/8com (non-polarity) 1790D-8BV8V and BV8VX 8 input / 8 output 1 1 s per block On-state voltage On-state voltage drop 8 points non-isolated, sinking 10V dc minimum 24V dc nominal 28.8V dc maximum 0.5V dc maximum Bit Produces I7 I6 I5 I4 I3 I2 I1 I0 s O7 O6 O5 O4 O3 O2 O1 O0 On-state current Off-state leakage signal delay 1mA minimum per channel 0.5mA maximum Off to On: 0.5ms maximum On to Off: 1.0ms maximum Word Bit Description Produces tatus bits - when the bit is set (1), the input is on. Bit 00 corresponds to input I0, bit 01 corresponds to input I1, bit 02 corresponds to input I2, bit 03 corresponds to input I3, etc. s bits - when the bit is set (1), the output is on. Bit 00 corresponds to output O0, bit 01 corresponds to output 01, bit 02 to output 02, bit 03 to output 03, etc. current rating Common type General pecifications 8 green status Maximum 0.5A per output 4.0A maximum per common 8 points/8com DeviceNet - base block upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc Field upply voltage - 24V dc nominal Voltage range V dc dissipation V dc per point Wiring voltage: 1250V ac rms DeviceNet to logic: non-isolated DeviceNet power: non-isolated 37-pin D-hell connector

14 14 DeviceNet Digital and D-hell Blocks CompactBlock LDX I/O 24VDC 8 Universal /8 ourcing Base and Expansion Blocks D-8BV8B and BV8BX Wiring Diagram for D-hell Connector COM0 I0 I1 I2 I3 I4 I5 I6 I7 O0 O2 COM2 O1 O3 O4 O6 O5 O implified chematic +/- 24Vdc Opto ystem Circuitry Indication LED (logic) COM1 COM1 COM1 COM1 COM1 COM3 COM3 COM3 COM3 COM1 COM1 COM1 COM1 COM3 COM3 COM3 COM3 COM3 inking inputs - wire Com 1 to Field (+) 24V dc, wire Com 0 to Field (-) ourcing inputs - wire Com1 to Field (-), wire Com 0 to Field (+) 24V dc Note: all Com 1 are internally connected. ourcing outputs -wire Com 2 to Field (+) 24Vdc, wire Com 3 to Field (-) Note: all Com 3 are internally connected. Connection izes Blocks -/+ COM Indication LED (logic) ystem Circuitry 1790D-8BV8B, BV8BX Opto Protected Device I/O Points 8 input / 8 output Produce 1 1 Bit Produces I7 I6 I5 I4 I3 I2 I1 I0 s O7 O6 O5 O4 O3 O2 O1 O0 Word Bit Description Produces tatus bits - when the bit is set (1), the input is on. Bit 00 corresponds to input I0, bit 01 corresponds to input I1, bit 02 corresponds to input I2, bit 03 corresponds to input I3, etc. s bits - when the bit is set (1), the output is on. Bit 00 corresponds to output O0, bit 01 corresponds to output 01, bit 02 to output 02, bit 03 to output 03, etc. Vdc 24Vdc Block pecifications 1790D-8BV8B, BV8BX INPUT PECIFICATION s per block On-state voltage On-state current Off-state voltage Nominal input impedance Common type OUTPUT PECIFICATION s per block On-state voltage On-state voltage drop On-state current Off-state leakage signal delay current rating Common type General pecifications 8 points non-isolated, sinking or sourcing 9.6V dc minimum 24V dc nominal 28.8V dc maximum 8mA maximum per 28.8V dc 5V dc maximum 4.8KΩ 8 green status 8 points/8com (non-polarity) 8 points non-isolated, sourcing 10V dc minimum 24V dc nominal 28.8V dc maximum 0.5V dc maximum 1mA minimum per channel 0.5mA maximum Off to On: 0.5ms maximum On to Off: 1.0ms maximum 8 green status Maximum 0.5A per output 4.0A maximum per common 8 points/8com D-8BV8B DeviceNet - base block upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc Field upply voltage - 24V dc nominal Voltage range V dc dissipation V dc per point voltage: 1250V ac rms DeviceNet to logic: non-isolated DeviceNet power: non-isolated Wiring 37-pin D-hell connector

15 CompactBlock LDX I/O DeviceNet Digital and D-hell Blocks 15 24VDC 16 ourcing Base and Expansion Blocks D-0B16 and B16X implified chematic Wiring Diagram for D-hell Connector COM0 O1 O3 O5 O0 O2 O4 O6 O7 O8 O10 O12 O14 COM2 O9 O11 O13 O COM1 COM1 COM1 COM1 COM1 COM3 COM3 COM3 COM3 COM1 COM1 COM1 COM1 COM3 COM3 COM3 COM3 COM3 Indication LED (logic) Vdc ourcing outputs - wire Com 0 and Com 2 to Field (+) 24V dc, wire Com 1 and Com 3 to Field (-) Note: all Com 1 and Com 3 are internally connected. ystem Circuitry Opto Protected Device 24Vdc Block pecifications 1790D-OB16 and 1790-OB16X Connection izes Blocks I/O Points Produce 1790D-0B16 and 1790-OB16X 16 outputs 0 2 s per block On-state voltage On-state voltage drop On-state current Off-state voltage Off-state leakage signal delay current rating Common type 16 points non-isolated, sourcing 10V dc minimum 24V dc nominal 28.8V dc maximum 0.5V dc maximum 1mA minimum per channel 28.8V dc maximum 0.5mA maximum Off to On: 0.5ms maximum On to Off: 1.0ms maximum 16 green status Maximum 0.5A per output 4.0A maximum per common 8 points/8com for 1790D-0B16 Bit s 0 O7 O6 O5 O4 O3 O2 O1 O0 s 1 O15 O14 O13 O12 O11 O10 O9 O8 General pecifications DeviceNet - base block upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc Field upply voltage - 24V dc nominal Voltage range V dc dissipation V dc per point Word Bit Description s bits - when the bit is set (1), the output will be turned on. Bit 00 corresponds to output O0, bit 01 corresponds to output 01, bit 02 to output 02, bit 03 to output 03, etc. s bits - when the bit is set (1), the output will be turned on. Bit 00 corresponds to output O8, bit 01 corresponds to output O9, bit 02 to output O10, bit 03 to output O11, etc. Wiring voltage: 1250V ac rms 37-pin D-hell connector

16 16 DeviceNet Digital and D-hell Blocks CompactBlock LDX I/O 24VDC 16 inking Base and Expansion Blocks D-0V16 and V16X implified chematic Wiring Diagram for D-hell Connector COM0 O1 O3 O5 O0 O2 O4 O6 O7 O8 O10 O12 O14 COM2 O9 O11 O13 O COM1 COM0 COM0 COM0 COM0 COM2 COM2 COM2 COM2 COM0 COM0 COM0 COM0 COM3 COM2 COM2 COM2 COM2 Indication LED (logic) Vdc inking outputs - wire Com 0 and Com 2 to Field (+) 24V dc, wire Com 1 and Com 3 to Field (-) Note: all Com 0 and Com 2 are internally connected. ystem Circuitry Opto Protected Device 24Vdc Block pecifications 1790D-OV16 and 1790-OV16X s per block On-state voltage On-state voltage drop 16 points non-isolated, sinking 10V dc minimum 24V dc nominal 28.8V dc maximum 0.5V dc maximum Connection izes Blocks I/O Points Produce 1790D-0V16 and V16X 16 output 0 2 On-state current Off-state voltage Off-state leakage signal delay 1mA minimum per channel 28.8V dc maximum 0.5mA maximum Off to On: 0.5ms maximum On to Off: 1.0ms maximum 16 green status Bit s 0 O7 O6 O5 O4 O3 O2 O1 O0 s 1 O15 O14 O13 O12 O11 O10 O9 O8 current rating Common type General pecifications Maximum 0.5A per output 4.0A maximum per common 8 points/2com for 1790D-OV16 DeviceNet - base block upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc Word Bit Description s bits - when the bit is set (1), the output will be turned on. Bit 00 corresponds to output O0, bit 01 corresponds to output 01, bit 02 to output 02, bit 03 to output 03, etc. s bits - when the bit is set (1), the output will be turned on. Bit 00 corresponds to output O8, bit 01 corresponds to output O9, bit 02 to output O10, bit 03 to output O11, etc. Field Wiring upply voltage - 24V dc nominal Voltage range V dc dissipation V dc per point voltage: 1250V ac rms 37-pin D-hell connector

17 CompactBlock LDX I/O DeviceNet Digital and D-hell Blocks 17 6 Relay Base Block D-0W6 implified chematic Vdc Wiring Diagram for D-hell Connector +24V CH0 CH1 CH2 CH3 CH4 CH5 +24V COM0 COM1 COM2 COM3 COM4 COM Indication LED (logic) ystem Circuitry Connection izes Relay Block I/O Points Produce 1790D-0W6 6 outputs 0 1 Opto Bit s 0 O5 O4 O3 O2 O1 O0 24Vdc Word Bit Description s bits - when the bit is set (1), the output will be turned on. Bit 00 corresponds to output O0, bit 01 corresponds to output 01, bit 02 to output 02, bit 03 to output 03, etc. COM ource Load D-OW6 Relay type Wire pins 18 and 19 to Field (+) 24Vdc Wire pins 36 and 37 to Field (-) Block pecifications voltage range (load dependent) current rating (at rated power) Minimum load Maximum on-state voltage drop Initial Contact Resistance Expected contact life Maximum off-state leakage delay time Common type General pecifications DeviceNet Field Wiring Form A, normally open ingle pole, single throw 5-24V 2.0A resistive 30V 2.0A resistive 5-24V dc resistive 30V dc resistive 100µA, 100mV dc per input 2.0A, resistive load, 24V dc 30m ohm 300K cycles resistive 100K cycles inductive 1.5mA maximum 10ms maximum on to off or off to on 6 green status 1 point/1com upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc upply voltage - 24V dc nominal Voltage range V dc dissipation V dc per channel voltage: 1250V ac rms 37-pin D-hell connector

18 18 DeviceNet Digital and D-hell Blocks CompactBlock LDX I/O 8 Relay Expansion Block W8X implified chematic Vdc Wiring Diagram for D-hell Connector +24V CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 +24V COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM Indication LED (logic) ystem Circuitry Connection izes Relay Block I/O Points Produce W8X 8 outputs 0 1 Opto 24Vdc Bit s 0 O7 O6 O5 O4 O3 O2 O1 O0 Word Bit Description s bits - when the bit is set (1), the output will be turned on. Bit 00 corresponds to output O0, bit 01 corresponds to output 01, bit 02 to output 02, bit 03 to output 03, etc. COM ource Load OW8X Relay type Wire pins 18 and 19 to Field (+) 24Vdc Wire pins 36 and 37 to Field (-) Block pecifications voltage range (load dependent) current rating (at rated power) Minimum load Maximum on-state voltage drop Initial Contact Resistance Expected contact life Maximum off-state leakage delay time Common type General pecifications Field Wiring Form A, normally open ingle pole, single throw 5-24V 2.0A resistive 30V 2.0A resistive 5-24V dc resistive 30V dc resistive 100µA, 100mV dc per input 2.0A, resistive load, 24V dc 30m ohm 300K cycles resistive 100K cycles inductive 1.5mA maximum 10ms maximum on to off or off to on 8 green status 1 point/1com upply voltage - 24V dc nominal Voltage range V dc dissipation V dc per channel voltage: 1250V ac rms 37-pin D-hell connector

19 CompactBlock LDX I/O DeviceNet Digital and D-hell Blocks 19 4 Channel Current Block D-N4C0 implified chematic Wiring Diagram for D-hell Connector +24V CH0 CH1 CH2 CH3 +24V +24V COM COM COM COM Multiplexer 24VDC Field ignal A/D elect upply ignal Control Optocouplers Vcc Indicator LEDs Micro controller upply Xcur Network ystem 24VDC Wire pins 17, 18 and 19 to Field (+) 24Vdc Wire pins 35, 36 and 37 to Field (-) Data File Word Bit Position Not Used Data Channel 0 1 Not Used Data Channel 1 2 Not Used Data Channel 2 3 Not Used Data Channel 3 4 Not Used Connection izes Block I/O Points Produce 1790D-N4C0 4 channel 10 0 Word Decimal Description Bit Read Bits Channel 0 input data Word 0 Bits Not used: et to 0 Read Bits Channel 1 input data Word 1 Bits Not used: et to 0 Read Bits Channel 2 input data Word 2 Bits Not used: et to 0 Read Bits Channel 3 input data Word 3 Bits Not used: et to 0 Read Word 4 Bits tatus bits for individual channels - Bit 00 corresponds to input channel 0, bit 01 corresponds to input channel 1 and so on. When set (1) indicates: No field power Open wire (4-20mA current input only) Under range (4-20mA current input only) Recoverable module fault (whole channel to be set) Unrecoverable module fault (whole channel to be set) Bits Not used: et to 0 Block pecifications 1790D-N4C0 s per module Current (software configurable) Resolution Converted Data Conversion Time Overall accuracy Calibration Impedance Insulation Resistance General pecifications DeviceNet Field Wiring 4 channel single-ended, non-isolated 4-20mA (default) 0-20mA 12 bits-unipolar 1/4096 maximum 3.90µA/bit (4-20mA) 4.88µA/bit (0-20mA) Binary data 0000 to 0fff (max scale) 10ms/channel 0.2% Full C None required 249Ω 20MΩ 250V dc (between insulated circuits) upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc upply Voltage - 24Vdc nominal Voltage Range V dc (+10%) Dissipation - 1.5W dc voltage: Type Test 1250V ac rms for 60 seconds DeviceNet to logic: non-isolated Field power: non-isolated 4 red/green I/O status 37-pin D-hell connector IMPORTANT: This analog base module can accommodate a maximum of two discrete expansion modules.

20 20 DeviceNet Digital and D-hell Blocks CompactBlock LDX I/O 4 Channel Voltage Block D-N4V0 implified chematic Wiring Diagram for D-hell Connector +24V CH0 CH1 CH2 CH3 +24V +24V COM COM COM COM Multiplexer 24VDC Field ignal A/D elect upply ignal Control Optocouplers Vcc Indicator LEDs Micro controller upply Xcur Network ystem 24VDC Wire pins 17, 18 and 19 to Field (+) 24Vdc Wire pins 35, 36 and 37 to Field (-) Data File Word Bit Position Not Used Data Channel 0 1 Not Used Data Channel 1 2 Not Used Data Channel 2 3 Not Used Data Channel 3 4 Not Used Connection izes Block I/O Points Produce 1790D-N4V0 4 channel 10 0 Word Decimal Description Bit Read Bits Channel 0 input data Word 0 Bits Not used: et to 0 Read Bits Channel 1 input data Word 1 Bits Not used: et to 0 Read Bits Channel 2 input data Word 2 Bits Not used: et to 0 Read Bits Channel 3 input data Word 3 Bits Not used: et to 0 Read Word 4 Bits tatus bits for individual channels - Bit 00 corresponds to input channel 0, bit 01 corresponds to input channel 1 and so on. When set (1) indicates: No field power Open wire (4-20mA current input only) Under range (4-20mA current input only) Recoverable module fault (whole channel to be set) Unrecoverable module fault (whole channel to be set) Bits Not used: et to 0 Block pecifications 1790D-N4V0 s per module 4 channel single-ended, non-isolated Voltage 0-10V Resolution 12 bits-unipolar 1/4096 maximum 2.44mV/bit Converted Data Binary data 0000 to 0fff (max scale) Conversion Time 10ms/channel Overall accuracy 0.2% Full C Calibration None required Impedance 500KΩ minimum Insulation Resistance 20MΩ 250V dc (between insulated circuits) General pecifications DeviceNet upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc Field upply Voltage - 24Vdc nominal Voltage Range V dc (+10%) Dissipation - 1.5W dc voltage: Type Test 1250V ac rms for 60 seconds DeviceNet to logic: non-isolated Field power: non-isolated 4 red/green I/O status Wiring 37-pin D-hell connector IMPORTANT: This analog base module can accommodate a maximum of two discrete expansion modules.

21 CompactBlock LDX I/O DeviceNet Digital and D-hell Blocks 21 2 Channel Current Block D-N0C2 implified chematic Wiring Diagram for D-hell Connector +24V CH0 CH1 +24V +24V Indicator LEDs COM COM D/A Data Control Optocouplers Micro controller Xcur Network Wire pins 17, 18 and 19 to Field (+) 24Vdc Wire pins 35, 36 and 37 to Field (-) Block pecifications 24VDC Field Connection izes Block I/O Points Produce 1790D-N0C2 2 channel 0 4 Word Decimal Bit Description Write Word 0 Write Word 1 Data File upply Vcc Bits Channel 0 output data Bits Not used: et to 0 Bits Channel 1 output data Bits Not used: et to 0 upply ystem 24VDC Word Bit Position Not Used Data Channel 0 1 Not Used Data Channel D-N0C2 s per module Current Resolution Converted Data Conversion Time Overall accuracy Calibration Allowable external output load resistance Insulation Resistance General pecifications DeviceNet Field Wiring 2 channel single-ended, non-isolated 0-20mA 12 bits 1/4096 maximum 4.88µA/bit Binary data 0000 to 0fff (max scale) 2ms/channel 0.2% Full C None required 600Ω maximum 20MΩ 250V dc (between insulated circuits) upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc upply Voltage - 24Vdc nominal Voltage Range V dc (+10%) Dissipation - 1.5W dc voltage: Type Test 1250V ac rms for 60 seconds DeviceNet to logic: non-isolated Field power: non-isolated 2 red/green I/O status 37-pin D-hell connector IMPORTANT: This analog base module can accommodate a maximum of two discrete expansion modules.

22 22 DeviceNet Digital and D-hell Blocks CompactBlock LDX I/O 2 Channel Voltage Block D-N0V2 implified chematic Wiring Diagram for D-hell Connector +24V CH0 CH1 +24V +24V Indicator LEDs COM COM D/A Data Control Optocouplers Micro controller Xcur Network Wire pins 17, 18 and 19 to Field (+) 24Vdc Wire pins 35, 36 and 37 to Field (-) Block pecifications 24VDC Field Connection izes Block I/O Points Produce 1790D-N0V2 2 channel 0 4 Word Decimal Bit Description Write Word 0 Write Word 1 Data File upply Vcc Bits Channel 0 output data Bits Not used: et to 0 Bits Channel 1 output data Bits Not used: et to 0 upply ystem 24VDC Word Bit Position Not Used Data Channel 0 1 Not Used Data Channel D-N0V2 s per module 2 channel single-ended, non-isolated Voltage 0-10V Resolution 12 bits 1/4096 maximum 2.44mV/bit Converted Data Binary data 0000 to 0fff (max scale) Conversion Time 2ms/channel Overall accuracy 0.2% Full C Calibration None required Allowable external output load 1KΩ minimum resistance Impedance 0.5Ω maximum Insulation Resistance 20MΩ 250V dc (between insulated circuits) General pecifications DeviceNet upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc Field upply Voltage - 24Vdc nominal Voltage Range V dc (+10%) Dissipation - 1.5W dc voltage: Type Test 1250V ac rms for 60 seconds DeviceNet to logic: non-isolated Field power: non-isolated 2 red/green I/O status Wiring 37-pin D-hell connector IMPORTANT: This analog base module can accommodate a maximum of two discrete expansion modules.

23 CompactBlock LDX I/O DeviceNet Digital and D-hell Blocks 23 4 Channel RTD Base Block D-4R0 implified chematic Wiring Diagram for D-hell Connector +24V +24V +24V CH0_B CH1_B CH2_B CH3_B CH0_A CH1_A CH2_A CH3_A CH0 EXC0 A ENE0 B RTN0 Com Connection izes Block I/O Points Produce 1790D-4R0 4 channel 10 0 Word Decimal Bit Description Read Word 0 Bits Channel 0 input data Read Word 1 Bits Channel 1 input data Read Word 2 Bits Channel 2 input data Read Word 3 Bits Channel 3 input data Read Word 4 Data File VA2 Multiplexer Bits Underrange for individual channels - Bit 00 corresponds to input channel 0, bit 01 corresponds to input channel 1 and so on. When set (1) the input signal is below the input channel s minimum range. Bits Not used: et to 0 Bits Overrange for individual channels - Bit 08 corresponds to input channel 0, bit 09 corresponds to input channel 1 and so on. When set (1) the input signal is above the input channel s maximum range, or open RTD is detected. Bits Not used: et to 0 Word Bit Position RTD Data Channel 0 1 RTD Data Channel 1 2 RTD Data Channel 2 3 RTD Data Channel 3 4 Not Used 11 VA1 VA1 EXC Current A- Vref 10 AIN+1 A/D AIN+2 AIN- Vref 9 8 Not Used Vcc Micro controller Channel elect VA3 VDC UA1 Auxiliary 24VDC UA2 Vcc Field UA3 upply A- Transceiver Network Transmit Recieve upply 3 Indicator LEDs 2 ystem 24VDC 1 0 COM COM COM COM COM COM COM COM COM COM COM COM Wire pins 17, 18 and 19 to Field (+) 24Vdc Wire pins 35, 36 and 37 to Field (-) Block pecifications 1790D-4R0 s per module 4 channel, RTD/Resistance Range ohm ensors upported ensor Type Degree Counts Resolution Resistance 100mΩ 1 to 625Ω 10 to mΩ Resistance 10mΩ 1 to 327Ω 100 to mΩ 100ohm Pt/α = ohm Pt/α = ohm Pt/α = ohm Pt/α = ohm Pt/α = ohm Pt/α = ohm Nickel 120ohm Nickel 200ohm Nickel 500ohm Nickel -200 to +850 C -200 to +850 C -200 to +650 C -200 to +640 C -200 to +640 C -200 to +640 C -60 to 250 C -80 to 260 C -60 to 250 C -60 to 250 C to to to to to to to to to to C 0.1 C 0.1 C 0.1 C 0.1 C 0.1 C 0.1 C 0.1 C 0.1 C 0.1 C Resolution 16 bits across 625ohms, 0.1 C/bit or 0.1 F/bit (RTD ensors) 20bit igma-delta modulation converter Data Format 16 bit Integer (2 s compliment) Module can Time Notch Filter = 60Hz Overall accuracy 0.2% Full C-55 C ettable Notch Filter 10Hz (default), 25Hz, 50Hz, 60Hz, 100Hz, 250Hz, 500Hz Open Wire Detection Out of range, open wiring Excitation Current 1mA Impedance 5M ohm DeviceNet upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc Field upply Voltage - 24Vdc nominal Voltage Range V dc (+10%) Dissipation - 1.5W dc voltage: Type Test 1250V ac rms for 60 seconds DeviceNet to logic: non-isolated Field power: non-isolated 4 red/green I/O status Wiring 37-pin D-hell connector IMPORTANT: This module does not support any expansion modules.

24 24 DeviceNet Digital and D-hell Blocks CompactBlock LDX I/O 4 Channel Thermocouple Base Block D-4T0 implified chematic + _ CH0 A B Connection izes Block I/O Points Produce 1790D-4T0 4 channel 10 0 Word Decimal Bit Description Read Word 0 Bits Channel 0 input data Read Word 1 Bits Channel 1 input data Read Word 2 Bits Channel 2 input data Read Word 3 Bits Channel 3 input data Read Word 4 VA2 Multiplexer A- Vref A/D VA1 AIN+ AIN- Vref Vcc Micro controller Channel elect VA3 VDC UA1 Auxiliary 24VDC UA2 Vcc Field UA3 upply A- Transmit Recieve upply Transceiver Indicator LEDs Network ystem 24VDC Bits Underrange for individual channels - Bit 00 corresponds to input channel 0, bit 01 corresponds to input channel 1 and so on. When set (1) the input signal is below the input channel s minimum range. Bits Not used: et to 0 Bits Overrange for individual channels - Bit 08 corresponds to input channel 0, bit 09 corresponds to input channel 1 and so on. When set (1) the input signal is above the input channel s maximum range, or open RTD is detected. Bits Not used: et to 0 Wiring Diagram for D-hell Connector +24V +24V +24V Wire pins 17, 18 and 19 to Field (+) 24Vdc Wire pins 35, 36 and 37 to Field (-) Block pecifications CH0_B CH1_B CH2_B CH3_B CH0_A CH1_A CH2_A CH3_A D-4T0 s per module 4 channel, Thermocouple/mV Range mV ensors upported ensor Type Range caling Voltage 10µV to mV to Type B 300 to 1800 C 3000 to Type E -270 to 1000 C to Type J -210 to 1200 C to Type K -270 to 1370 C to Type R -50 to 1768 C -500 to Type -50 to 1768 C -500 to Type T -270 to 400 C to 4000 Type N -270 to 1300 C to Resolution 16 bits, 0.1 C/bit or 0.1 F/bit (Thermocouple ensors) 20bit igma-delta modulation converter Data Format 16 bit Integer (2 s compliment) Module can Time Notch Filter = 60Hz Overall accuracy 0.2% Full C-55 C ettable Notch Filter 10Hz (default), 25Hz, 50Hz, 60Hz, 100Hz, 250Hz, 500Hz Open Wire Detection Out of range, open wiring Cold Junction 0 to 70 C Compensation Range Impedance 5M ohm General pecifications DeviceNet upply voltage - 24V dc nominal dissipation - 1.2W 28.8V dc Field upply Voltage - 24Vdc nominal Voltage Range V dc (+10%) Dissipation - 1.5W dc voltage: Type Test 1250V ac rms for 60 seconds DeviceNet to logic: non-isolated Field power: non-isolated 4 red/green I/O status Wiring 37-pin D-hell connector IMPORTANT: This module does not support any expansion modules. Data File Word Bit Position Thermocouple Data Channel 0 1 Thermocouple Data Channel 1 2 Thermocouple Data Channel 2 3 Thermocouple Data Channel 3 4 Not Used Not Used

25 CompactBlock LDX I/O DeviceNet Digital and Terminal Blocks 25 DeviceNet Digital and Terminal Blocks The DeviceNet digital and analog terminal block I/O is exchanged with the master through a poll, change-of-state, or cyclic connection. Polled - a master initiates communication by sending its polled I/O message to the block. The block consumes the message, updates any outputs, and produces a response. If any inputs are present, the response will contain the input data. Change-of-state - productions occur when an input changes. If no input change occurs within the expected packet rate, a heartbeat production occurs. This heartbeat production tells the scanner module that the block is alive and ready to communicate. Consumption occurs when data changes and the master produces new output data to the block. Cyclic - allows configuration of the block as an I/O client. The block will produce and consume its I/O cyclically at the rate configured. The DeviceNet Network uses advanced network technology, producer/consumer communication, to increase network functionality and throughput. Visit our Web site at for producer/ consumer technology information and updates. General pecifications The following table contains specifications that are common to all of the DeviceNet base and expansion blocks in this section. Individual block connection sizes, word/bit definitions, schematics, wiring diagrams and specifications are detailed after this table. Environmental pecifications Operating Temperature 0 to 55 C (32 to 131 F) IEC (Test Ad, Operating Cold), IEC (Test Bd, Operating Dry Heat), IEC (Test Nb, Operating Thermal hock) torage Temperature -40 to 85 C (-40 to 185 F) IEC (Test Ab, Un-packaged Non-operating Cold), IEC (Test Bb, Un-packaged Non-operating Dry Heat), IEC (Test Na, Un-packaged Non-operating Thermal hock) Relative Humidity 5-90% non-condensing IEC (Test Db, Un-packaged Non-operating) Operating Altitude 2000m Vibration Hz EC (Test Fc, Operating) Environmental pecifications hock: Operating I0g Non-operating 30g IEC Test Ea, (Unpackaged hock) Emissions Group 1, Class A CIPR 11 ED Immunity 8kV air discharges IEC Radiated RF Immunity 10V/m with 1kHz sine-wave 80%AM from 80MHz to 1000MHz 10V/m with 200Hz 50% Pulse 900Mhz IEC EFT/B Immunity 5kHz on power ports 5kHz on signal ports 5kHz on communications ports IEC urge Transient Immunity Conducted RF Immunity +1kV line-line(dm) and +2kV line-earth(cm) on power ports +1kV line-line(dm) and +2kV line-earth(cm) on signal ports +2kV line-earth(cm) on shielded ports IEC Vrms with 1kHz sine-wave 80%AM from 150kHzto 80MHz IEC Enclosure Type Rating None (open style) Mounting DIN rail or screw Dimensions 52x104x42mm (2.03x4.07x1.64in) Weight 0.3lb (0.1kg) 1 Refer to publication , Programmable Controller Wiring and Grounding Guidelines. DeviceNet pecifications Network protocol I/O lave messaging: - Poll command - Bit trobe command - Cyclic command - CO command Network length 500 meters 125Kbps 100 meters 500Kbps 1 red/green module status 1 red/green network status Number of nodes 64 maximum - rotary switch type node address setting Communication rate 125Kbps, 250Kbps, 500Kbps - auto baud rate selection Type test 1250Vac rms for 60 seconds between field power and DeviceNet (I/O to logic) Wiring Refer to publication DN General pecifications Wiring Category 2 1 Product Certifications (when product or packaging is marked) c-ul-us CE 2 C-Tick 2 ODVA UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.. and Canada European Union 89/336/EEC EMC Directive, compliant with: EN ; Industrial Emissions EN ; Industrial Immunity EN61326; Meas./Control/Lab., Industrial Requirements EN ; Industrial Immunity Australian Radiocommunications Act, compliant with: A/NZ 2064; Industrial Emissions ODVA conformance tested to ODVA DeviceNet specifications 1 Refer to publication , Programmable Controller Wiring and Grounding Guidelines. 2 ee the Product Certification link at for Declarations of Conformity, Certificates, and other certification details.