IPCP Pro Series Setup Guide

Transcription

1 IPCP Pro Series Setup uide IMPORTANT: o to f the complete user guide, installation instructions, and specifications befe connecting the product to the power source. The Extron IPCP Pro Series IP Link Pro Control Processs integrate Ethernet connection into AV systems to allow users to remotely control, monit, and troubleshoot AV equipment, including display devices and switchers. All models include an embedded web server. Depending on the model, an IPCP Pro control process can include multiple bidirectional serial pts, relays, IR/serial pts, digital, flex, switched VDC power output pts, a volume control pt, contact input pts f use in applications that require control and moniting of multiple devices within a large-scale AV system. All models include an Extron pt, which allows a variety of devices to be connected to a single control process. devices include an array of button panels as well as power and signal hubs. devices are automatically recognized by the control process and can be added removed at any time. IPCP Pro Control Processs with AV provide a secure netwk dedicated f the connection and isolation of AV devices. This guide provides instructions f an experienced installer to install an IPCP Pro Series control process and to create a basic configuration. Use Extron Toolbelt software to discover and manage the IPCP Pro control process and other Extron control products. Configure the control process using Extron lobal Configurat software running in lobal Configurat Professional (C Professional) lobal Configurat Plus (C Plus) mode, program the control process using Extron lobal Scripter (S). The IPCP integrates seamlessly with Extron lobalviewer Enterprise (VE) software and Extron Control apps f remote control applications. These control processs suppt multiple TouchLink Pro touchpanel interfaces over a standard Ethernet netwk. lobal Configurat and other useful software applications are available at Setup Checklist: How to Proceed With Installation et Ready Familiarize yourself with the features of the control process (see Front Panel Features Models Without AV on page 4, Front Panel Features Models With AV on page 5, Rear Panel Features Models Without AV on page 6, and Rear Panel Features Models With AV on page 7) and of any TouchLink Pro touchpanels that will be part of the system. Download and install the latest version of the following: Toolbelt software f discovering the control process and other control products on the netwk, f managing ce settings, and f upgrading firmware when needed. lobal Configurat (C) software f configuring the control system. lobal Scripter software f programming the control process (as an alternative to C) UI Designer software f designing layouts f Extron TouchLink Pro touchpanels and third party touch interfaces IP Link Pro device drivers f use with C, to make control of AV devices possible IR Learner Pro software f use with models that have IR receiver pts. Use this to create your own IR drivers using the remote control of an AV device, if drivers are not already available from Extron All are avail able from (see Locating Software, Firmware, and Driver Files on the Extron Website on page 5). Obtain netwk infmation f the unit from the netwk administrat. You also need the following details f each IP Link Pro device: DHCP setting (on off) Subnet mask Username Device (IPCP Pro, TouchLink Pro, IPL Pro) IP address ateway IP address Passwds AV IP address (f models with AV ) Write down the MAC address of each netwk interface on each IP Link Pro device to be used. Obtain model names and setup infmation f devices the IPCP will control.

2 IPCP Pro Series Setup uide (Continued) Each control process comes with a facty-installed Secure Sockets Layer (SSL) security certificate. If you intend to install a different SSL certificate, contact your IT department to obtain the certificate f instructions on how to obtain one. See Secure Sockets Layer (SSL) Certificates in the IPCP Pro Series User uide f requirements and guidelines regarding SSL certificates. Mount and Cable All Devices Mount the unit to a rack furniture (see Mounting on the next page). Cable devices to the control process (see Cabling and Features on page 8). Connect power cds and power on all the devices. Set Up the Control Process and Touchpanels f Netwk Communication Connect the PC that you will use f setup, the ( AV ) pt of the control process, and the touchpanels to the same Ethernet netwk. F control process and AV connections, see Control, Bidirectional and AV (Ethernet) on page 9. Start Toolbelt and use it to set the IP address, subnet, gateway IP address, DHCP status, and related settings. See the flowchart in Netwk Communication Setup on the next page. NOTE: When setting up DHCP during netwk configuration if using a host name instead of an IP address, the user must enter a qualified host name (Username.HostName.Domain). F example: somename.extron.com. Configure Program the Control Process and Touchpanels The most basic steps are outlined below in the recommended der. NOTE: See the Toolbelt Help File, lobal Configurat Help File, lobal Scripter Help File, and UI Designer Help File as needed f step-by-step instructions and detailed infmation. The help file f C includes an introduction to the software and how to start a project and configuration. If TouchLink Pro third party touchpanels are part of the system, start and use UI Designer to design, save, and build the graphical user interface (UI) layout f the touchpanels. NOTE: To redeem (activate) a LinkLicense, go to and follow the online instructions. Using C, create a new C Professional C Plus project and configure the control process and other IP Link Pro devices. The configuration tells the control process: How its pts function What to monit How to control other products When to do things Which touchpanels to interact with Whom to notify, how, and under what circumstances Configure pts on the control process. Select device drivers and link them to each serial, IR/serial, Ethernet pt. Select settings (serial protocol, relay behavi, digital flex settings) as needed. Add devices and set them up: Ensure that the hardware address set on each device is distinct and matches the address used in the configuration. Assign button functions as desired. Set up monits, schedules, macros, and local variables. Add touchpanels and set them up: Add the UI configuration f each touchpanel to the C project using lobal Configurat. Assign any appropriate functions, monits, schedules to the touchpanels and their buttons. If not using C Professional C Plus, use lobal Scripter to program the control system as desired. Program pts on the control process. Program each serial, IR/serial, Ethernet pt. Program relay behavi, digital, and flex settings as needed. Add devices and set them up: Ensure that the hardware address ( ID) set on each device is distinct and matches the address programmed f it in the IPCP. Program button functions as desired.

3 Add touchpanels and set them up: Upload the UI configuration f the touchpanels. Program the touchpanel buttons. Save and build the project. Upload the system configuration to the control process. Test and Troubleshoot Test the system (see the IPCP Pro User uide f an outline of the system testing procedure). Make adjustments to wiring configuration as needed. Netwk Communication Setup Netwk setup is essential pri to configuration. Use the following flowchart as a guide to setting up the control process f netwk use. Netwk Communication Setup Connect the PC and the pt AV pt of the control process to the same netwk. Apply power to all devices. Open the Toolbelt software from within lobal Configurat (C Professional C Plus mode) as the stand-alone application. Start Device Discovery. Toolbelt displays a list of all Extron control devices connected to the netwk. Using the MAC address, locate the desired control process in the list and select it. F each netwk interface (, and AV ), use the Set IP feature in Toolbelt use the Toolbelt Manage > Netwk Settings tab feature to enter the IP address and subnet address, then configure other netwk settings as needed. Figure. Netwk Setup Mounting Securely mount the control process and other devices and attach cables using the wiring section (see Cabling and Features on page 8) as a wiring guide. Optional U rack shelves and furniture mounting bracket kits are available f use with the control process. Read the instructions and UL guidelines that come with the rack shelf mounting kit f installation procedures. See the product-specific page at f a list of compatible accessies f mounting your control process. 3

4 IPCP Pro Series Setup uide (Continued) Panels and Locations of Features Location and quantity of and cresponding connects vary by model, but the functions and pt wiring are identical across models f each pt type. Front Panel Features Models Without AV IPCP Pro Embedded Control Process Without AV (within another device) S LIMIT IR/S OVER (Serial) IR/ Serial Digital Relay IPCP PRO 50 Power R S LIMIT OVER IR/S IR 000 ACT / Netwk Reset Button (recessed) IR Receiver Digital IPCP PRO 350 Power R S LIMIT OVER 3 IR/S IR 000 ACT 3 Reset Switched Button VDC (recessed) (Serial) IR/Serial Relay Flex IR Receiver / Netwk IPCP PRO 550 Power R SWITCHED VDC LIMIT FLEX OVER OVER S LIMIT IR 000 ACT NOTE: Numbers adjacent to crespond to the like-numbered rear panel pts. 5 IR Receiver IR Learning 5 Angle and Distance " (4 30 cm) Figure. Front Panels: IPCP Pro Series Rack Mountable Models Without AV NOTES: F reset mode infmation, see the IPCP Pro Series User uide. The Reset button and power f the IPCP Pro embedded control processs are located next to the rear panel connects. The embedded control processs do not have an IR learning sens. 4

5 Front Panel Features Models With AV This section shows the front panels of a couple representative AV models, not all models. IPCP PRO 360 Power R LIMIT BUSY ERROR OVER 3 IR/S IR 000 ACT AV 3 Reset Button (recessed) (Serial) IR/Serial Digital Relay IR Receiver AV Figure 3. IPCP Pro 360 Front Panel IPCP Pro Embedded Control Process With AV (within another device) LIMIT BUSY IR/S ERROR OVER (Serial) IR/ Serial Digital Relay Figure 4. Figure 3: IPCP Pro Embedded Control Processs With AV Front Panel 5

6 IPCP Pro Series Setup uide (Continued) Rear Panel Features Models Without AV IPCP Pro Embedded Control Process Without AV (within another device) R E D I E D I 3 C C DIITAL +V +S -S POWER V.0A MAX VOL V C C DIITAL +V +S -S IR/S IPCP Pro 50 IPCP PRO 50 M S S PWR OUT = 6W 3 PWR OUT = 6W S F J L A K J F L IPCP Pro 350 E D I M 3 DIITAL IPCP PRO 350 POWER V.0A MAX C C +V +S -S 3 S S PWR OUT = 6W A F J L IPCP Pro 550 J 00-40V ~ 50-60Hz.A MAX 3 7 S S S S SWITCHED VDC 40W MAX TOTAL S S S S VDC 5 6 PWR OUT = W +V +S -S 7 8 FLEX IPCP PRO 550 M B C D E F H L Figure 5. IPCP Pro Control Processs Without AV Rear Panels A Power input connect (external power supply) B Power input connect (internal power supply) c Switched VDC power output pts D 3-pole pts (RS-3-only) E 5-pole pts (RS-3/RS-4/RS-485) F IR/serial output pts Relay pts H Flex pts (digital input/output analog input) I Digital pts (digital input/output) J pts K Volume control pt L connects and (Ethernet) M MAC address label 6

7 Rear Panel Features Models With AV This section shows rear panels of some representative models with AV. IPCP Pro Embedded Control Process With AV (within another device) E D 3 I DIITAL AV AV 3 E IPCP Pro 55 D I DIITAL L M R C C +V +S -S POWER V.0A MAX VOL V C C +V +S -S IR/S AV S S PWR OUT = 6W AV PWR OUT = 6W S F J L N A K J F N IPCP Pro 360 E D I 00-40V ~.5A MAX 3 C C DIITAL +V +S -S IPCP AV AV PWR PWR 3 IPCP PRO 360 IPCP M Hz S S PWR OUT = 6W PoE+ OUT PoE+ OUT B F J N L Figure 6. IPCP Pro Control Processs With AV Rear Panels A Power input connect (external power supply) B Power input connect (internal power supply) D 3-pole pts (RS-3-only) E 5-pole pts (RS-3/RS-4/RS-485) F IR/serial output pts Relay pts I Digital pts (digital input/output) J pts K Volume control pt L connects and (Ethernet) M MAC addresses N AV connect and (Ethernet), some with PoE+ and PoE+ The following pts are not shown in figure 6 but are available in some AV models such as the IPCP Pro 555. c Switched VDC power output pts H Flex pts (digital input/output analog input) 7

8 IPCP Pro Series Setup uide (Continued) Cabling and Features Attach cables using the following wiring diagrams as a guide. Full details are available in the IPCP Pro Series User uide. ATTENTION: Installation and service must be perfmed by experienced personnel. L installation et l entretien doivent être effectués par du personnel expérimenté. Power Input External Smooth POWER V x.xa MAX 3/6" (5 mm) Max. Tie Wrap Ridged Power Input, External Power Supply Connect to Front panel ( ) blinks during included VDC boot-up and remains lit when the power supply. IPCP is powered and operational. Ridged Return + VDC input Smooth To AC power round all devices. R Front Panel External VDC Power Supply NOTE: Check the polarity of the power supply befe connecting it to the IPCP. ATTENTION: Always use a power supply supplied specified by Extron. Use of an unauthized power supply voids all regulaty compliance certification and may cause damage to the supply and the unit. Utilisez toujours une source d alimentation fournie par Extron. L utilisation d une source d alimentation non autisée annule toute certification de confmité réglementaire et peut endommager la source d alimentation que l unité. Power Input Internal 00-40V 50-60Hz Power Input, Internal Power Supply Connect to 00 to Front panel ( ) blinks 40 VAC. during boot-up and remains lit when the IPCP receives power. R.A MAX Rear Panel Front Panel Power Output Switched VDC Power Output SWITCHED VDC 40W MAX TOTAL Rear Panel VDC 3/6" (5 mm) Max. Switched VDC Power Output Total output f all four pts combined: VDC, 40 watts (max.) Cresponding front panel green ( ) light when power is available at each pt. SWITCHED VDC LIMIT 3 Front Panel 4 OVER Lights if total power drawn is 4-46 watts. Lights if total power drawn exceeds 47 watts. Power output shuts off until the user crects the overload. Tie Wrap Power Output PoE+ The IPCP Pro 360 can output PoE+ on AV pts and 3. F details, see the PoE+ output infmation on page. 8

9 Control, Bidirectional Serial () Rear Panels Serial () Pts Front Panels 7 3-pole Select protocol via software. (RS-3) pt default protocol: 9600 baud REL LAYS 5-pole 8 data bits stop bit C 4 8 (RS-3, RS-4, RS-485) no parity no flow control S S NOTE: The 5-pole pts suppt both hardware and software flow control. The 3-pole pts suppt software flow control only. = Request to Send = Clear to Send = Transmitting Data = Receiving Data To 5-pole pt Clear to send Request to send round Receive Transmit Receive () Transmit () Project, Panel Display, PC, Other RS-3, RS-4, RS-485 Device 3 To 3-pole pt Heat Shrink Over Shield Wires round Receive Transmit Heat Shrink Receive () Transmit () Strip wires 3/6" (5 mm) max. RS-3- Controllable Device NOTE: If you use cable that has a drain wire, tie the drain wire to ground at both ends. 5-pole Pin Configurations Pin () () 3 () 4 () 5 () RS-3 round RS round + + RS-485 Data- (pins & tied together) round Data+ (pins 4 & 5 tied together) Control, Bidirectional and AV (Ethernet) Default pt IP addresses and recommended connections vary depending on whether not the IPCP model includes AV pts. 7/8" ( mm) 3/6" (5 mm) Max. Heat Shrink on Outer Jacket to Inner Conduct Transition Extron STP 0-P Cable TIP: STP 0-P cable, shown at left, is recommended f these connections. F best results, insulate the common drain wires using heat shrink. Models without AV pts Insert Twisted Pair Wires Ethernet TCP/IP Netwk PC RJ-45 Connect Rear Panel, Rack Mount Models Pins: Activity Link (Ethernet) Models Without AV Default protocol, public pts: Default login IPCP IP address: credentials: ateway IP address: Username: Subnet mask: admin DNS address: Passwd: DHCP client: off extron Link speed and duplex level: autodetected Data rates: 0/00/000Base-T NOTE: IPCPs with me than one pt function as multipt, unmanaged netwk switches so you can connect additional devices to the same netwk. Front Panel, Rack Mount Models 000 ACT Mbps Connection Netwk is active. Data is being sent/received. 9

10 IPCP Pro Series Setup uide (Continued) Models with AV pts PC Cpate TCP/IP Netwk Ethernet Insert Twisted Pair Wires PC Cpate TCP/IP Netwk Rear Panels IPCP AV PWR AV PoE+ OUT PWR RJ-45 Connect MAC: A6-YY-YY-YY IPCP 3 PoE+ OUT Pins: Activity Ethernet MAC: A6-YY-YY-YY # AV Link (Ethernet) Models With AV Default protocol, pts: IP address: ateway IP address: Subnet mask: DNS address: DHCP client: off Link speed and duplex level: autodetected Data rates: 0/00/000Base-T Default login credentials: Username: admin Passwd: extron Front Panels 000 ACT AV Mbps Connection Netwk is active. Data is being sent/received. NOTE: IPCPs with me than one AV pt function as multipt, unmanaged netwk switches so you can connect additional devices to the same netwk. Models with AV AV pts Insert Twisted Pair Wires Ethernet AV Netwk PC PC Pins: RJ-45 Connect IPCP AV PWR AV PoE+ OUT PWR MAC: A6-YY-YY-YY IPCP 3 PoE+ OUT Activity Ethernet AV Netwk MAC: A6-XX-XX-X X MAC: A6-YY-YY-YY AV Rear Panels Link AV (Ethernet) Default protocol, AV : IP address: Subnet mask: DNS address: DHCP client: off (disabled) DHCP server off (disabled) Link speed and duplex level: autodetected Data rates: 0/00/000Base-T Default login credentials: Username: admin Passwd: extron Front Panels 000 ACT AV Mbps Connection Netwk is active. Data is being sent/received. NOTE: IPCPs with me than one AV pt function as multipt, unmanaged netwk switches so you can connect additional devices to the same netwk. AV DHCP Server The AV DHCP Server is disabled by default. It can be enabled to dynamically assign IP addresses to DHCP clients on the AV. Default protocol, AV when DHCP server is enabled: DHCP server IP address: Subnet mask: DNS address: DHCP dynamic address range f client devices: Maximum served addresses when DHCP server is enabled: 50 DHCP client address lease time: 4 hours. To use DHCP in the AV :. Using Toolbelt, enable the DHCP server f the AV within the control process (see the software programming help file f details).. Enable DHCP on each client AV device (see the user guide f each product). 3. Connect client AV devices to the AV. 0

11 PoE+ output: The IPCP Pro 360 offers Power over Ethernet+ (PoE+) output on AV pts and 3. These RJ 45 connects, labeled PoE+ Out, can output a maximum of 30 watts per pt. The cresponding Power lights when the pt provides power. PoE+ pts can be monited f status and power consumption, and power output can be scheduled. F details, see the IPCP Pro Series User uide and the lobal Configurat Help File. PWR PoE+ OUT ATTENTION: Power over Ethernet (PoE) is intended f indo use only. It is to be connected only to netwks circuits that are not routed to the outside plant building. L alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur uniquement. Elle doit être connectée seulement à des réseaux ou des circuits qui ne sont pas routés au réseau ou au bâtiment extérieur. All models (with without AV ) MAC address: Each netwk interface of the control process is assigned a unique user hardware ID number (MAC address) (f example, A6-05-C-A0). You may need this address during control process configuration. A label that indicates the MAC address is located on the rear side panel of the unit. MAC Address Control, Unidirectional IR/Serial Rear Panels IR/Serial Pts Output options: IR (30 khz to 300 khz, with without carrier signals) Unidirectional RS-3 Front Panels S S S S IR/S S S S S S S IR/Serial Light when signals are transmitted on the cresponding IR/serial pt. (-) To a Project, Panel Display, the Wired IR Remote RS-3 Pt of a Source Device IR RS-3 Output round Unidirectional IR S round IR Output Signal (-) (+) (+) (-) (+) Two Single IR Emitters To the IR Receiver of a Project, Display, Source Device Control, Unidirectional Relays All relays are nmally open. Nmally Open () Nmally Open () Common Common Rear Panels Relays Connect devices f contact control. Do not exceed a total of 4 V at A f each pt. Front Panels C C Nmally Open Closed C C Relay Light when the cresponding relays are activated (tied to ND, closed). To Room Control Equipment Common Relay Relay To Room Control Equipment

12 IPCP Pro Series Setup uide (Continued) Control, Unidirectional Flex Digital Rear Panel Front Panel DIITAL FLEX Digital (digital input/output) Configure each pt as a digital input output, with without +5 VDC pull-up. Use these pts to: Monit trigger events and functions (toggle relays, issue commands, send ), once configured. Power other devices that accept a TTL signal. Flex (digital input/output analog input) Configure each pt as an analog input as a digital input output with without +5 VDC pull-up. Digital Light when the cresponding pts are active. Heat Shrink Over Shield Wires round Wire Nut Share the same ground among connections. FLEX Flex Light when the cresponding pts are active. 4 3 Switch, Sens Device 4 Device 3 Device Device (Switches, senss,, relays, similar items) Control Link (green) Lights steadily and remains lit when the unit detects connected devices, there are no ID conflicts, and firmware is not currently being synchronized. +V +S -S PWR OUT = 6W Rear Panels, Rack Mount Models PWR OUT = W +V +S -S Drain Wires +V + VDC +S + Signal -S - Signal round Accessy Pt Connect the first device to this pt, then connect other devices and accessies to that device in the desired topology (daisy chain, star, combination). Wire the connects the same at both ends f every device. See the Technology Reference uide f the recommended distance from the control process to the last device and maximum quantity of devices per control process. The IPCP Pro can provide power to the button panel devices. pt on an device (button panel similar device) DISPLAY ON Busy (amber) Blinks while firmware is being synchronized. VOLUME PC VIDEO VOLUME MUTE Err (red) Blinks if the unit detects an ID conflict. OFF LAPTOP DOC CAM PC DVD VIDEO LIMIT BUSY ERROR S LIMIT OVER OVER Front Panels, Rack Mount Models Status (green) Limit (amber) Lights steadily and remains lit while the pt uses the maximum threshold power. Overload (red) Lights steadily when the pt exceeds maximum threshold power usage and enters the fault state. During this fault state, pt power is shut down until the power usage falls back below the threshold. The Over remains lit during the fault state. is not lit This indicates one of the following conditions: No power is present. No devices are detected. is blinking fast An ID conflict has occurred: two devices have the same bus ID number. is blinking slowly A firmware update is in progress: the control process is synchronizing firmware of the panel(s). is lit steadily Power is present with confirmed communication and there are no ID conflicts in the entire system.

13 EBDB MINI Rear Panel ( use an EBDB 0-pt hub) DISTRIBUTION HUB +V +S -S +V +S -S +V +S -S Connections Connect up to four (4) devices to the distribution hub (EBDB MINI). Wire the connects the same at both ends. X +S-S +V+S-S +V+S-S 3/6" (5 mm) Max. ATTENTION: Do NOT connect the power pin to any device ATTENTION: that is already Do powered NOT by the IPCP connect Pro control the power process pin by an additional to any device power supply. that is NE connectez already PAS la powered broche by the d'alimentation IPCP à un Pro appareil control déjà alimenté par process le processeur by de an contrôle IPCP additional Pro ou par power une supply. autre source d'alimentation. +V +S -S + VDC + Signal - Signal round IPCP Pro Rear Panel +V +S -S PWR OUT = 6W + V + S S Tie drain wires to ground. pt on an EBP other device Powered +S-S device(s) Tie drain wires to ground. +V+S-S Control Volume Reference voltage: 0 VDC Rear Panel V C VOL V C Control voltage output: 0-0 VDC Volume Control This pt can be used to control the volume and mute unmute the audio f Extron half rack width audio amplifiers. Connect to an Extron audio amplifier to permit volume control via touchpanel controls, macros, schedules. Do not exceed 0 VDC input voltage. Configure the maximum and minimum voltage limits. Set Soft Start mode off on (default). Soft Start mode allows volume to gradually increase from mute to the previous level after muting power-on to prevent loud audio bursts. round (nd) C Control voltage (variable output to amp from IPCP Pro) This signal controls the amp volume. V Reference voltage input (from amplifier) This allows the IPCP Pro to detect when the amp is present. NOTE: Use shielded cable and place the control process as close as possible to the amplifier to avoid picking up background noise via the cable. Ideal cable length is six feet (.8 m) less. Example: Connecting to Extron Amplifiers VOL V C IPCP Pro Rear Panel XPA 00 0V 50mA V C STANDBY MPA 40 Series MPA 8T, MP 0 Series REMOTE 0V 50mA V C MPA 5 Plus REMOTE 0V VOL/MUTE MPA 5 REMOTE NOTE: When audio mute is active, the control process sets output voltage to 0 VDC, even if the voltage range (minimum and maximum voltage limits) has been set to levels above zero, such as V to 8 V. V C 0V 50mA 0V VOL/MUTE 50mA C VOL/MUTE V 0V round C Control voltage V Reference voltage 3

14 IPCP Pro Series Setup uide (Continued) Reset Modes: a Brief Summary The IP Link Pro control processs offer the following reset modes: Use Facty Firmware: Press and hold the front panel Reset button while applying power to the unit. Keep holding the button down until the Power blinks twice, f 6 seconds, then release the button. The control process enters facty firmware mode. F units with firmware pri to version.x, the blinks quickly. Use this mode to revert to facty firmware in the event of a firmware failure. Do not continue to operate the control process using the facty firmware version. If you want to use the facty default firmware version, you must upload that version again. Project Recovery: See the IPCP Pro Series User uide f instructions. Use this mode to recover the project in the event of a lost user name and passwd. Run/Stop Program: Hold down the Reset button f about 3 seconds, until the Power blinks once. Release and press the Reset button momentarily (f < second) within second. (Nothing happens if the momentary press does not occur within second.) The blinks times if the program is starting. The blinks 3 times if the program is stopping. This mode allows you to restart any programs stopped by an IP settings reset. Toggle DHCP Client: Press the Reset button five times (consecutively). Release the button. Do not press the button within 3 seconds following the fifth press. Use this mode to enable disable the DHCP client f the pt. The Reset blinks 6 times if the DHCP client is enabled. The Reset blinks 3 times if the DHCP client is disabled. NOTES: DHCP toggle mode is suppted on firmware version 3.0 higher. By default DHCP is off and the unit uses a static IP address. When you disable the DHCP client, the unit reverts to using the previously-set static IP address. Reset All IP Settings: Press and hold the front panel Reset button f 6 seconds. After the Power blinks twice, release and momentarily press the Reset button. Use this mode to reset all netwk settings to facty default values without affecting user-loaded files. This reset mode also stops any running programs. This resets the settings f both and AV pts, including turning DHCP off. Reset to Facty Defaults: Press and hold the front panel Reset button f 9 seconds. After the Power blinks three times, release and momentarily press the Reset button. Use this mode to return the control process to facty default settings. This mode also deletes all user-loaded files and configurations. F detailed infmation on each mode and its use, see the IPCP Pro Series User uide at Resources Obtaining Control Drivers Extron provides an extensive selection of device drivers available on the Extron website. If the system requires a control driver that is not already available, you have additional options: Request a new serial (RS 3) Ethernet driver from Extron. Create your own custom IR device driver using IR Learner Pro software. Follow the directions in the IR Learner Pro Help File to create a driver by using the remote control f that device and the IR receiver pt on the front panel of the IPCP Pro. Obtaining Instructions, Infmation, and Assistance A checklist of basic setup steps is provided at the beginning of this guide. F additional infmation see the help files and the IPCP Pro Series User uide, available at If you have questions during installation and setup, call the Extron S3 Sales & Technical Suppt Hotline the Extron S3 Control Systems Suppt Hotline ( ). 4

15 Locating Software, Firmware, and Driver Files on the Extron Website There are three main ways to find software, firmware, and device drivers within Via links from the web page f the specific product Via the Download page (Click on the Download tab at the top of any page within Via links from search results NOTES: F some software you have the option to click the Download Now button to begin downloading the software file. F other software there is a link f contacting an Extron suppt representative who can provide you access to the latest version. To obtain Extron control product software, you must have an Extron Insider account. Extron provides training to our customers on how to use the software. Access to the full features of lobal Configurat Professional is available to those who successfully complete Extron Control Professional Certification. New RS-3 and Ethernet drivers are required. You must use serial and Ethernet drivers developed specifically f the IP Link Pro platfm. With the exception of IR device drivers, drivers used f the previous generation IP Link (non-pro) control processs are not compatible. 5

16 IPCP Pro Series Setup uide (Continued) Overall Configuration Procedure f the Control Process Within lobal Configurat (C Professional C Plus mode): Configure the IP settings of the control process and the TouchLink Pro touchpanels. See Netwk Communication Setup on page 3. If desired required, install a new security certificate (via Toolbelt). Create a new C Professional C Plus project and add the control process to it. No Will TouchLink Pro third party touchpanels other user interfaces be used? Yes Create UI layouts f the touchpanels other interfaces:. Start UI Designer.. Create UI layout designs f each TouchLink Pro, third party touchpanel (with a TouchLink Interface), a computer mobile device (with LinkLicense). 3. Save and build the UI layout file. Or... Download existing UI layouts from identical touchpanels. Configure pts on the control process. Create monits, schedules, timers, macros, and local variables. Add touchpanels other interfaces (if used) to the project. Impt UI layouts and configure the touchpanels other interfaces. Save the project. Build and upload the configuration to the control process. Test the system, make adjustments, finalize configuration. Figure 7. Overall Configuration Steps F infmation on safety guidelines, regulaty compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulaty Compliance uide on the Extron website Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners Rev. E 08 8