OUTPUT SMD 202 AUDIO INPUT AUDIO. G 3.5 mm, 5-pole captive screw connector for analog stereo. audio output

Transcription

1 SMD 202 Setup Guide The Extron SMD 202 is a compact, high performance media player and live stream decoder for H.264 streaming applications. It provides the flexibility to present a locally connected AV signal, decode a live streaming source, or play back media files from internal memory, removable SD card, local USB, or network storage. The SMD 202 supports a wide range of media file container formats and streaming protocols, making it adaptable for use with a variety of encoded media. Advanced signal processing, scaling, and aspect ratio management supply high quality signals to AV displays. An intuitive, interactive on-screen menu provides easy setup and source selection using front panel buttons or the optional handheld IR remote control. Designed for pro AV applications, the SMD 202 can be controlled using Ethernet, RS-232, IR, or wired IR. Install the SMD 202 Before mounting and connecting the SMD 202, turn off all devices that will be connected to it. The SMD 202 is housed in a 1-inch high, half rack width, 6 inch deep metal enclosure that can sit on a table with the provided rubber feet or can be rack mounted. Select a suitable location, then choose an appropriate mounting option. Make all external device connections before applying power. Rear Panel Features A B C D E F G H I J K POWER 12V 1.3A MAX USB SD HDMI OUTPUT HDMI OUTPUT SMD 202 AUDIO AUDIO L R L R IR IN RS-232 RESET S G Tx Rx G LAN Figure 1. SMD 202 Rear Panel A 12 VDC power input B USB type A receptacle for external storage device C Slot for additional storage on SD card (optional) D HDMI input E HDMI output F 3.5 mm, 5-pole captive screw connector for analog stereo audio input G 3.5 mm, 5-pole captive screw connector for analog stereo audio output H 3.5 mm, 3-pole captive screw connector for wired IR receiver input I 3.5 mm, 3-pole captive screw connector for Simple Instruction Set (SIS ) control over RS 232 or serial pass through to other devices J Reset button and LED K RJ-45 Ethernet connector for connection to a LAN Input Connections D HDMI input Connect an HDMI (or DVI with suitable adapter) source to the HDMI input connector. F Audio input Connect a balanced or unbalanced stereo (or dual mono) line level audio source to this 5-pole 3.5 mm captive screw connector. Wire the connector as shown in figure 2, below. Sleeve(s) Balanced Stereo Input (high impedance) Sleeve Sleeve Unbalanced Stereo Input (high impedance) Do not tin the wires! Figure 2. Audio Input Wiring 1

2 SMD 202 Setup Guide (Continued) Control System and External Device Connections The SMD 202 can be configured and controlled from the RS-232 port or the front panel mini-type B USB config port using DataViewer, or from the LAN port using a standard Web browser. Since the LAN port must be connected for streaming source input, Extron recommends also using it for configuration and remote control of the SMD 202. B USB host port Connect a USB compatible storage device to this port (see figure 1 on page 1). C SD Card slot This slot supports SD, SD-HC, and SD-XC card types up to 512 Gigabyte card capacity and Class 10 (UHS 1) data rates up to 25 Mbytes/sec. Mounted media is listed in the user file system under the media folder. The media folder and contents are accessible from the File browser of the default Web interface (see Connect to the SMD 202 and Play a File or Stream: on page 6). H IR In Connect an (optional) IR receiver to this 3-pole 3.5 mm captive screw connector to extend the range of the optional IR remote control (see figure at right). The handheld H I J K IR remote provides access to the on-screen menus for configuration and for direct control over playback (see the SMD 202 User Guide). IR IN RS-232 RESET I RS-232 To control the SMD 202 using SIS commands over RS-232, connect the S G Tx Rx G host RS-232 cable to the rear panel (see the figure at right) with a 3-pole captive screw LAN connector for bi directional (±5 V) serial host control. The default protocol for this port is 9600 baud, no parity, 8 data bits, 1 stop bit, and no flow control (handshaking). J Reset button and LED The SMD 202 has four reset modes to restore default configuration settings or all settings back to factory defaults (see figure at right). The LED indicates the desired reset mode, and provides the reset status during the reset operation. For information on using the reset mode, see the SMD 202 User Guide. K RJ-45 Ethernet connector (LAN) Use a standard Ethernet cable to connect to a network. The table (right) includes the default network settings of the SMD 202. The left side (amber) LED indicator on the LAN connector blinks in a pattern to indicate the network link speed. Three blinks, pause 1 Gbps Two blinks, pause 100 Mbps One blink, pause 10 Mbps NOTE: The SMD 202 LAN connection uses Auto MDI-X allowing direct connection of a control PC using a standard straight through Ethernet cable. Output Connections E HDMI output Connect an HDMI (or DVI with suitable adapter) display device to the HDMI output connector. The EDID of a connected display is read and the output automatically configured. For non-standard displays or devices, see the SMD 202 User Guide for additional output resolutions and format settings. G Audio output Connect a balanced or unbalanced stereo (or dual mono) line level audio device to this 5-pole 3.5 mm captive screw connector (see figure 1, G on page 1). Wire the connector as shown in figure 3, below. ATTENTION: + S G IR Transmitter IP Address: Subnet Mask: Default Gateway: DHCP: OFF For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative ( ) contacts. Pour l audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts négatifs ( ). Receive Transmit Ground Connected RS-232 Device Pins Sleeve(s) Balanced Audio Output NO Ground Here Sleeve(s) NO Ground Here Unbalanced Audio Output Do not tin the wires! Figure 3. Audio Output Captive Screw Connector Wiring 2

3 SMD 202 Setup Guide (Continued) Power Supply Connection A 12 VDC power input Connect the provided 12 VDC power supply to the rear panel captive screw connector and plug in the power cord. Verify the front panel power LED lights. AC Power Input DC Power Output Figure 4. PS 1215 C External Power Supply ATTENTION: Always use a power supply provided by or specified by Extron. Use of an unauthorized power supply voids all regulatory compliance certification and may cause damage to the supply and the end product. Utilisez toujours une source d alimentation fournie ou recommandée par Extron. L utilisation d une source d alimentation non autorisée annule toute conformité réglementaire et peut endommager la source d alimentation ainsi que le produit final. Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities. The power supply is to be located within the same vicinity as the Extron AV processing equipment in an ordinary location, Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium, or desk. Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d aération ou dans les cavités murales. La source d alimentation doit être située à proximité de l équipement de traitement audiovisuel dans un endroit ordinaire, avec un degré 2 de pollution, fixé à un équipement de rack à l intérieur d un placard, d une estrade, ou d un bureau. The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/ NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently fixed to building structure or similar structure. Cette installation doit toujours être en accord avec les mesures qui s applique au National Electrical Code ANSI/ NFPA 70, article 725, et au Canadian Electrical Code, partie 1, section 16. La source d alimentation ne devra pas être fixée de façon permanente à une structure de bâtiment ou à une structure similaire. 3

4 Front Panel Features ABC D E F G H I IR CONFIG HDMI DECODER MENU ENTER SMD 202 Figure 5. SMD 202 Front Panel A Power LED Lights solid green when the SMD 202 is powered, blinks green during power up, and lights solid red when in standby (low power) mode. B Playback status indicator Dual-color LED indicates the current state of playback operation. Solid Green The SMD 202 is actively decoding a stream or playing a file. Blinking Green A stream or file is selected for decoding, but playback is paused. Off The selected source is not being decoded. Solid Red Lights during playback errors and when the source is unavailable. C Network status indicator Dual-color LED indicates the current state of network operation and connection quality. Solid Green Indicates network conditions are favorable for the current source. The LED is also lit if the current source is a local file. Red/Green When flashing red and green, source or network conditions are marginal and might compromise image or audio quality. Solid Red Indicates server or network conditions are poor and are compromising video or audio quality. Off No network connectivity. D IR receiver window Allows remote operation using a compatible handheld IR remote control (optional). E Config port Connect a control PC to this port with a mini-type B USB cable (not supplied). Use this port to send Simple Instruction Set (SIS ) commands to the SMD 202 for device configuration and control. NOTE: For information on using this port for device configuration and control and for a list of available SIS commands, see the SMD 202 User Guide. F Input indicators HDMI Indicates the rear panel HDMI input (see figure 1, D on page 1) is selected. Decoder Indicates the decoder is selected. G Menu selection button Press to activate the interactive On-screen Display (OSD) menu system. H Input selection and OSD menu navigation buttons By default, the up and down arrow buttons allow input selection between HDMI or decoder inputs. Press UP to select the HDMI and DOWN to select the Decoder input. When the OSD menu is active, the directional arrow buttons provide navigation within the OSD menu structure (see the SMD 202 User Guide for information about the OSD menu). I Enter button Press to make a selection on the interactive OSD menu. Change the IP Address using the OSD menus: 1. Connect the external power supply to a 100 to 240 VAC, 50 or 60 Hz power source. The SMD 202 powers up and undergoes a self testing sequence. 2. Power up the display device. The SMD 202 reads the EDID of the display and sets the output resolution and format. 3. Press Menu (see figure 5, G) to open the OSD menu (see figure 6, below). 4. Navigate to the Communications submenu using the UP and DOWN arrow buttons (see figure 5, H). 4

5 The Communications submenu opens. Configure the communications ports to connect the SMD 202 to your local network (consult your IT department for the suitable network settings). The default settings are shown below Figure 6. On Screen User Interface, Communications submenu. 5. Press the Enter or button to enter the submenu panel. 6. Press the front panel (or remote control) Up and Down buttons to scroll through the submenu items. Stop on the IP Address field. 7. Press the arrow button to move the selection arrow to the first octet of the address Press the Up and Down buttons to change the octet to the required address, or enter the numbers directly using the optional IR remote control number buttons. NOTE: Press the front panel buttons quickly to accelerate the numbers in the octet. As you press faster, more numbers are skipped so that the time locating the final number is reduced. You can also accelerate through the numbers using the IR remote control. The longer you hold the Up or Down button, the faster it accelerates through the number field. 9. Repeat steps 7 and 8 for the next three octets. 10. Press the Enter button to accept the new value or press the Menu button to cancel the changes. 11. In the same manner, repeat steps 4 through 10 to configure all communications settings. 12. When you are finished configuring the communications settings, press Menu on the front panel or the remote to exit the OSD. Alternatively, you can use the following SIS commands to enable and disable DHCP, view and configure the IP address, and change the subnet mask. Use DataViewer, available from the Extron Web page, on a control PC via any of the control system connections to send commands to the SMD 202 and view the results (ee the SMD 202 User Guide for additional information). SIS Command E CI} E 1DH} E 0DH} E 2BOOT} E CI} E CS} Description View the current IP address Enable DHCP Disable DHCP Restart the network interface and apply changes Set the default IP address Set the default subnet mask NOTE: } = Carriage return (no line feed, hex 0D). 5

6 Connect to the SMD 202 and Play a File or Stream: 1. Ensure the control PC is on the same subnet. Power the PC, and open one of the following web browsers: Google Chrome version 40 or higher (recommended) Mozilla Firefox (version 35 or higher) Microsoft Internet Explorer version 9 or higher (for Windows operating systems) NOTE: If you are using Internet Explorer, compatibility mode must be turned off. Apple Safari version 8 or higher (for Mac OS X operating systems) NOTE: The SMD 202 embedded Web pages are designed for viewing in a browser at 100% zoom. The appearance of individual pages can differ from those in this guide for other zoom ratios. 2. Enter the SMD 202 IP address into the browser address bar and press <Enter> on the keyboard. The Player page opens with the Player Controls (see figure 7, A), Browser (B), Lists (C), and Playlist Editor (D) panes open. The browser Streams tab (F) is selected displaying available streams on the network. Select the Files tab (G) in the Browser pane to see a list of clips in the internal memory, on attached devices, or in shared network folders xsap:// :sme es-rtp xsap:// :sme100-hd stream xsap:// :pdlab-30 xsap:// :pdlab-31 xsap:// :pdlab xsap:// :pdlab-34 xsap:// :pdlab xsap:// :classroom xsap:// :cameras xsap:// :sme-100-hd-08-ce-38+stream xsap:// :sme100-hd- xsap:// :sme-100-hd-08-ce-38+stream Figure 7. SMD 202 Player Page 3. Drag and drop a media clip from the Browser (B) Streams or Files tab to the Player Controls (A) pane. The clip plays on the display connected to the HDMI output (see figure 1, E on page 1 ). 4. If the clip does not start automatically, press Play (H) on the player controls. NOTE: To enable automatic playback of clips as they are loaded into the Player Controls pane, press Load Play (I) on the player controls. Further configuration and control options, including connection to network shared folders, are available (see the SMD 202 User Guide at and the SMD 202 Embedded Web Pages Help File [see figure 7, E, above]) Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners Rev. B 03 18